K9N Platinum (not SLI) Ethernet/LAN ports shut down

Not sure if this has been up before but i could not find this exact problem. I have the K9N Platinum with am AMD 64x 4200+ CPU and OCZ 1GB x2 mem. My build and install of XP went without incident. My problem is that when I start to download anything of size, the LAN shut down. It will say "cable unplugged". If I switch to the second port, it will be good for a while, then the same thing. The only fix is to reboot. I am connected through a switch. I loaded the latest drivers (nVidia) from the monitor software. I found a different set on the NVidia web site and installed, but now it will not pick up DHCP. It will work if I hard code the IP. I read that it should be using Realtek drivers, not Nvidia. Please help!!! I opened a case with support but they have not answered yet.

That is a start on Specs. You can look at anyone's signatuires here to see what is most commonly looked for in specs. Your are missing the PSU specs.
However one of the first things to try is to go into Bios and set optimized defaults. Then you will need to make sure nothing else in Bios has changed as setting Optimized defaults usually changes things quite a bit.
Then make sure that your using the drivers that came with the board including the NVidia and Network drivers.
You may have to enter Device manager and remove the Network Driver and let it restart.
You did answer one question many folks would have with the specs you gave about memory. The memory you have listed should be fine.

Similar Messages

  • Number of Ethernet Devices Supported on Ethernet/LAN port of Airport Express

    I am using an Airport Express to extend my wireless network (Apple Time Capsule Base) and using the ethernet/LAN port to connect a wired device (a DirecTV DECA) so that my DirecTV HD DVR box can connect to the internet thru my home network. Works great. I have Whole Home DVR installed and so the other DirecTV receivers in the house are connecting to one another over the the coax and using the (DECA - Ethernet over Coax) to talk to one another and they each recieve an IP address via DHCP from the Apple Time Capsule Base - obviously thru the brdige created by the AirPort Express. Recently added an additional DirecTV reciever and for some reason this one will not get an address? Is as if the Aiport Express has "maxed out" the number of ethernet devices it will connect or bridge on the LAN side? I have tried shutting everything down and bringing DirecTV recievers on in different orders and it is alwasy the last one (the 5th one) that fails to get an address. Anyone have any knowledge if there is indeed a limit of the number of ethernet devices that are supported on the Ethernet/LAN port of the Airport Express? Thanks for any insight.

    in theory, yes, but you work network admin may have locked the network preventing this from working

  • Equium M50 will not recognise the LAN port - error: Network Cable unplugged

    I own a Toshiba Equium M50 and have problems with the Marvell Yukon 88E8036 PCI-E Fast Ethernet Controller.
    I used to connect via an 'ADDON' Modem/ADSL Switch and had no problems. I then replaced the ADDON with a 'NETGEAR' DG834G ADSL Modem/Router to gain the wireless port, and since then my machine will not recognise the LAN port. <error: Network Cable unplugged>.
    I know that the cables are OK as I used them with other laptops and had no trouble. I can also plug in a PCI card to connect without any problems. It looks to me as if the Marvell Yukon 88E8036 PCI-E Fast Ethernet Controller has a problem with the netgear Modem/Router.
    Anyone out there with a similar experience and some advice/suggestions?
    PLEASE

    Hi
    For me it doesnt show like a LAN card problem but your router is a problem.
    Check the device manager if the LAN card was properly recognized. If there are no yellow exclamation marks so everything is ok!
    You can try to delete the LAN card from the device manager and after new reboot install the LAN driver again.
    The issue has stared after installing or connecting the new Netgear modem router.
    Therefore I would recommend to checking firstly the settings or to update the firmware on this router.
    I have found additionally these useful websites
    http://compnetworking.about.com/od/windowsnetworking/f/cableunplugged.htm
    http://www.experts-exchange.com/Networking/Broadband/DSL_Cable/Q_20381405.html

  • Can the Gigabit Ethernet LAN Port be used with a Thunderbolt to Gigabit Ethernet adaptor and then to a Thunderbolt Hard Drive as a back up drive?

    Can the Gigabit Ethernet LAN Port be used with a Thunderbolt to Gigabit Ethernet adaptor and then to a Thunderbolt Hard Drive as a back up drive?

    If you use ethernet to connect the two AirPort Extremes together, you'll have Gigabit speeds available at all of the ethernet ports on both routers.
    If you connect the second AirPort Extreme using wireless only and configure the Extreme to "extend a wireless network", then the maximum speeds that the second router can attain will be limited to the capability of the wireless connection. So, if you connect at normal "n" wireless speeds of say 130 Mbps, that will be the maximum speed available at the ethernet ports on the second AirPort Extreme.
    I think you can easily see the difference between Gigabit ethernet, which is 1000 Mbps compared to "n" wireless at 130 Mbps. Even if you can manage to connect at 5 GHz speeds for wireless, the max speed will be in the 300 Mbps range, more than 3 times slower than Gigabit ethernet. Normal "n" speeds will be about 7 times slower than ethernet.
    For streaming high definition video and other demanding sources, you'll need as much bandwidth (speed) as you can get. Ethernet is always the best choice if you can possibly use it. And...there's no wireless interference on an ethernet connection.
    Message was edited by: Bob Timmons

  • Error in premiere elements 11 program is not responding and needs to shut down

    hi ,
    Please help just installed premiere elements version 11 and many time this message is shown, program is not active and must be shut down, please wait until program reacts.
    How can i solve this issue?

    hi ATR,
    Thanks for your prompt reply:
    1 b. after you are in the workspace and are importing/editing/exporting? During Editing and add pictures and gopro files to the time line
    2
    1. Are you running the program as Administrator with an Internet connection?
    No not running in admin mode.
    Wifi connection is on
    Do you have the latest version of QuickTime
    Nieuw in QuickTime 7.7.6
    installed on your computer along with Premiere Elements 11? yes
    computer see attachment
    2. Does the problem exist with or without the antivirus and firewall(s) disabled?
    not tried yet , now avg 2015 virus scanner is on
    3. Are you working with pen and tablet device instead of mouse?
    No only laptop elan smart pad , on laptop.
    4. Is your video card/graphics card up to date according to the web site of the manufacturer of the card? How many
    video cards/graphics cards does you computer use?
    yes up to date only 1 card
    5. Please describe your computer resources - processor, clock speed, installed RAM, available hard drive space?
    Is the program installed to the default Local Disk C?
    Installed on local disk drive C
    See attachment for details

  • When I start iTunes on my home computer (Not a MAC), it automatically shuts down, and gives me the message that the Data Execution Prevention security feature has shut it down...what to do?

    When I start iTunes on my home computer (Not a MAC), it automatically shuts down, and gives me the message that the Data Execution Prevention security feature has shut it down...what to do?

    For general advice see Troubleshooting issues with iTunes for Windows updates.
    The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it, which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down page in case one of them applies.
    Your library should be unaffected by these steps but there is backup and recovery advice elsewhere in the user tip.
    tt2

  • I just subscribed to IHome but when it tries to gather information about my music library, I get an error message that my Itunes is not responding and then it shuts down. Has anyone else had this problem?

    I just subscribed to IHome but when it tries to gather information about my music library, I get an error message that my Itunes is not responding and then it shuts down. Has anyone else had this problem?

    Thanks so much but none of that helped.  It was driving me crazy because it would back up another external drive.  I just changed the name of the drive from iPhoto/iTunes Library to Media Libraries and IT WORKED!! I guess for some reason it didn't like the drive being called iPhoto or iTunes ???? I don't understand but I have tried so many solutions and exchanging things out but the name change did it????!!!
    Thank you for your help and replying to this.  Guess I made my own issue!

  • IMac does not power off when I shut down

    I have an iMac with 10.7 as the operating system. When I power down the machine the screen goes gray and just stays in the gray mode until I hold the power key down manually. It starts up normally, just a "shut down" issue. I recently upgraded from 10.6 to 10.7 and had the same problem with 10.6 (not sure that means anything.) I am pretty sure this is not a good way to shut down a Mac.  Any ideas on what might be going on here? Thanks.

    I have an iMac with 10.7 as the operating system. When I power down the machine the screen goes gray and just stays in the gray mode until I hold the power key down manually. It starts up normally, just a "shut down" issue. I recently upgraded from 10.6 to 10.7 and had the same problem with 10.6 (not sure that means anything.) I am pretty sure this is not a good way to shut down a Mac.  Any ideas on what might be going on here? Thanks.

  • Lighting bolt port shuts down macbook pro

    lighting bolt port shuts down macbook pro once the cable is pugged in. What is the cause of this problem

    Hi reginaldt,
    If your Mac unexpectedly turns off when you plug in a cable (unclear if you are describing a USB Lightning cable or a Thunderbolt cable) and you have checked to make sure there is no debris in either the cable jack or port, you may want to try resetting the PRAM and SMC:
    Apple Support: About NVRAM and PRAM
    http://support.apple.com/kb/ht1379
    Intel-based Macs: Resetting the System Management Controller (SMC)
    http://support.apple.com/kb/ht3964
    If the issue persists, you may find the troubleshooting steps in the following article helpful:
    OS X: When your computer spontaneously restarts or displays "Your computer restarted because of a problem."
    http://support.apple.com/kb/TS4636
    Regards,
    - Brenden

  • Migration from PC with MA did not end. Had to shut down MacBookPro. After restart no new user was created. Can't find the transferred data (35 GB). Would like to delete it.

    Migration from PC with MA did not end. Had to shut down MacBookPro. After restart no new user was created. Can't find the transferred data (35 GB). Would like to delete it.

    iTunes is required to initially activate the phone. Back when the iPhone 3G was sold, you would take it out of the box and see a "Connect to iTunes" screen. She HAD to connect to a computer in order to begin using the phone. Does she remember what computer this was?

  • My email is not visible and I cannot shut down the mail app

    My email is not visible and I cannot shut down the mail app

    Command + Option + Esc will prompt the Force Quit window where you can quit the Mail app.
    OS X: How to quit an unresponsive application using Force Quit

  • My Iphone 5 got stuck when I did rest all Settings in my iphone 5 and my iphone do not restart or shut down. The phone do not have the ability to shut down.

    my Iphone 5 got stuck when I did rest all Settings in my iphone 5 and my iphone do not restart or shut down. The phone do not have the ability to shut down.

    Did you try to press and hold the home and sleep button for about 10sec, until the Apple logo comes back again? You will not lose data by resetting the device.
    If this does not work, try connecting in recovery mode, explained in this article:
    If you can't update or restore your iOS device

  • Why does iPhoto start up every time I start the computer. I have not checked any box at shut down.

    Why does iPhoto start up every time I start the computer. I have not checked any box at shut down.
    Thanks,
    Bill

    Is it on your Log-In items?
    Do you have a disk or device formatted like a camera card attched to your computer - say with a FAT format?

  • Msi p4n sli - ethernet LAN connection not recognized after reinstall

    So I am reinstalling windows xp home edition after replacing a hard drive with over 1,000 bad sectors... The ethernet LAN worked just fine before reinstalling.  I don't have the original driver cd, so using another computer, i downloaded the latest nforce4 chipset / ethernet / IDE / SATA drivers from the msi downloads site.  Installed them and everything worked fine except that the network connection never showed up.  It is not to be found in the device manager, and I don't see it when I view hidden devices.  The LAN chip is enabled in the BIOS and it tried to netboot the first time i booted with the new hard drive (hadn't put the cd in the drive  ).   When that didn't work, I tried downloading the latest chipset drivers from nvidia's site, and the same thing happened.  No local area connection!
    Is there something I'm missing?  is there a utility I should be installing before I install the chipset drivers, etc?
    I'm feeling stressed as I need to get this finished and returned to my client today but I've been dealing with this since yesterday to no avail
    Any help is appreciated!  thank you!
    Jeff

    A little embarrassed that I didn't figure it out earlier, but I tried several things, realized I had turned off the LAN chip in the BIOS and forgot to turn it back on after installing the second time.   
    once i enabled it, I had to manually pick drivers for the "Other PCI Bridge Device", and then for the the nforce network controller windows found after that.
    Lesson learned: stress inhibits cognitive function. 

  • K9N Platinum, 7600GTOC, SLI, No Video Signal

    Just built up my new system, specs as follows
    MSI K9N Platinum
    AMD 5200X2 AM2 CPU
    2 Gigs Corsair XMS2 DDR800
    2 BFG Tech 7600GT OC's in SLI
    Thermaltake TR2-500 Watt PSU +12V(1) 14A +12V(2)15A
    1 Maxtor 120 GB SATA 150
    1 Maxtor 160 GB SATA 160
    When i turned the computer on for the first time, the system boots up and there is one small beep, sounds like it is posting, but I get no video signal from my monitor, which I checked on my other computer and is working fine, I tried both video cards in the 1st slot, in non-sli mode and I get the same result each time, so I get no video signal with all ways tried? Do I not have enough power in this PSU to run what I have? The video manufacturer suggests a 450W PSU, which I meet, but do I not have enough juice the 12V rails? And would this cause the no signal? Any help would be much appreciated.

    Hello, welcome to forum.
    "When i turned the computer on for the first time, the system boots up and there is one small beep, sounds like it is posting, but I get no video signal from my monitor, which I checked on my other computer and is working fine, I tried both video cards in the 1st slot, in non-sli mode and I get the same result each time, so I get no video signal with all ways tried?"
    have you tried with one of them only into 1st PCI-E? use 1st DVI output, when using SLI, ensure SLI bridge is configured property, connect monitor to VGA onto 1st PCI-E slot. also check monitor output is configured property(etc: Input 1, Input 2).
    power down PC, remove power cord from the PSU and Clear CMOS Guide
    re-test.
    ensure all power cables are connected property. try to boot with one memory stick only into slot close to CPU socket.
    what D-bracket shows?
    "Do I not have enough power in this PSU to run what I have? The video manufacturer suggests a 450W PSU, which I meet, but do I not have enough juice the 12V rails? And would this cause the no signal?"
    yes, think is too weak for your system
    its recommended to get single rail with high amperes on +12V (over 30A)
    read here:
    PSU's---2 x 12v---The Dual Rail Myth
    Is your problem caused by your PSU?
    good suggestion can be found here:
    https://forum-en.msi.com/index.php?topic=105635.msg783148#msg783148
    https://forum-en.msi.com/index.php?topic=103299.msg757739#msg757739

Maybe you are looking for