K9N SLI PLATINUM low data transfer rate

Hi, (sorry for my pour english) I had to go back to Winxp native SATA/IDE drivers and my pc crash & BSOD problem it's gone! :D (BSOD when i install some programs or some games, listening music and moving data at the same time, etc.) now i'm available to execute multitasks without any troubles. But now the transference it's quite poor , I think this is an easy and temporary solution for this big problem.
I bought my PC on 2006 and the Windows XP drivers are from 2001, aren't new Nvidia/MSI drivers to fix this annoying problem?
Thanks.
AM2 3800+ X2
MSI K9N SLI PLATINUM, bios 1.4
2 x 1GB OCZ DDR2 6400 Platinum
PSU PowerCooler 550w
HD WD3200 SATAII
NX7900GT

I've got nearly the same problem, but a little worse. My data transfer rate seems very slow for a 100mb network and if I start copying files over the network, after only a couple of megs I lose connectivity to the network completely! I've removed the network cable and windows notices this, and when I put it back in windows also notices the change, but the green and orange lights on the port itself stay on solid. If I reboot windows everything comes back. I don't have problems browsing the web, seems to only happen when the ethernat port is running close to full load (for the connection speed of 100mb as apposed to 1gb).
Anyone else seen this? I'm on the latest drivers, the latest bios and I've tried disabling on of the network ports in the bios but his didn't work.
Kevpatts

Similar Messages

Data transfer rate Airport Extreme

which is the data transfer rate of the USB port in the Airport Extreme (4ta. Generation)...???
The HDD installed in that port, reads and writes very slow

I executed the test and I have a rate of data transfer of 1.9 escrtura of Mb/s and 2.7 reading Mb/s…. this is very under… What I can do.?
I even reinitiated the Airport and itself with the problem. I directly tested with the ports of iMac, and have DRT of 25.8 and 18.4 Mb/s
Ok, I am assuming that your measurements are in Mega Bytes per Second (MB/s) and not Mega Bits per Second (Mb/s). Even so, I would agree that you are getting low data transfer rates.
What is the make and model of the USB HDD that you have attached to the AirPort Extreme? Is it formatted in HFS+ or FAT32?
Also, the 25.8 & 18.4 readings when you have this drive attached directly is a bit low as well. I would expect something more like: 35 MB/s (read) & 25 MB/s (write) for a USB 2.0-connected HDD.

MSI K9N SLI Platinum - SATA not hot-swappable?

can i get a confirmation that K9N SLI Platinum motherboard does NOT support hot-swapping the SATA drives. I switched to this board for the AM2 socket and now i am not seeing the removable drive bays as hot-swappable (ie. no green arrow down by the clock). maybe i am missing a bios setting?

jackaninny
Quote
I check two machines today and one is just fine using the removable trays and any drives we put in there show up in the 'safely remove hardware' tool. the other machines does NOT detect any drives inserted while the machine is powered on and something else - under the 'policies' tab the top two choices ('optimize for quick removal' instead of 'optimize for performance') are greyed out but there is an option below them that i can check and uncheck (i cannot remember the exact title of this option).
I assume you are trying the same drives when you swap the removable trays between the two machines. Some drives have a jumper that has to be removed to enable SATA II operation, so if they aren't the same physical drives you might want to check that.
I think the stuff below the greyed out area in your 'Policies' tab is a check box that enables/disables write caching. You might want to try checking/unchecking that.
Also, you should check out the IDE/ATA Controller selection in the Device Manager. Take a look at each instance of controller that shows up there. SATA controllers actually a primary and secondary channel and each channel has a master and a slave drive, just like old IDE controllers. Look at each tab on both machines and make sure all of the drive's features are set identically on these tabs. Sometimes Windows can try to outsmart you. For example, I have an SATA II Maxtor drive that has its transfer mode downgraded to SATA I by Windows (there is a little yellow triangle with a '!' in the middle of the lower part of the panel). The help balloon for this arrtibutes it to 'excessive transfer errors.' I haven't tried to chase that one down yet, however.
As far as setting the machines up the same way, sometimes the sequence of driver installations can have an effect. For example, a RAID driver installed during Windows setup using the 'F6 - install other driver' option can behave differently from one installed with the Device Manager 'Update Driver' function.
Sorry I can't be of more help here.
Maybe someone else in this forum is a bit more knowledgable on the subject.
ss

K9N SLI Platinum - RAID 0 problems

Hi everyone,
I've just assembled a new pc with a K9N SLI Platinum (PCB Ver: 1.1; BIOS Ver: 1.3), 1GB (2x512MB DIMM1 & 3) Kingston KVR667, 2 Maxtor SATA-II disks, GF 7300GS with 256MB DDR2.
I'm able to install windows with one disk but can't do it with both disks setup as raid 0.
I've tried both Sata Raid Driver from cd and from MSI website.
With the driver from the cd windows setup finds the raid and starts installation, but freezes somewhere (totally random) without finishing.
With the driver downloaded from the website windows setup can't find the raid.
Any hints?
Thanks

Quote from: manuelmont on 25-September-06, 07:13:09
I tried once again to install windows and this time setup finished successfully and the computer boots from the raid. So my first question: what is the relation between the bootable option at the raid setup and the fact that the system booted without it?
I doubt that the removal of the floppy from the bootable devices list has anything to do with the successful install...
Well if it is grayed out in the RAID setup is because it is already Bootable, as for the removal of the floppy from the bootable devices, there are things that only the gods of the computers know...
Quote from: manuelmont on 25-September-06, 07:13:09
Everything seemed to work ok but the computer started to freeze once again during installation of other software which made the system unstable.
Then I replace the graphics card with an ATI X300 (just for testing) and the system became stable. I installed software, played some games without problems. As the GF 7300GS I removed works on another pc this seems to be some compatibility problem between the MB and the GF (turbocache?).
I used Sisoft Sandra 2007 Lite to test/benchmark the system. All the tests were almost normal (except memory - benchmark showed values a bit lower than I expected!) but I could not run Physical Disks Benchmark module neither Physical Disks Hardware module (but could benchmark the file system). What does this mean?
The disks are in fact DiamonMax 17 (6G160E0) but I'll try another brand as well, these are the only disks. On the IDE channel I only have one dvd recorder.
Your PSU has way to low amperage for that system, the test is the change you made from a superior GFX to a lower end one, the NX7300GS eats alot of amps in comparison to the X300, and it does not have nothing to do with the TurboCache feature.
As for Sisoft Sandra I don't use that "I'm a potty mouth" (pardon my french ) I use Lavalys Everest or for disks HDtach, and others.
You could not test the physical disks because they are in RAID mode, but you can test or benchmark the logical disks because they are the partitions you created in the physical disks and are divided by the 2 disks, half in one half in the other...
I hope this will shed some light into the questions...
Be well....

How to find the max data transfer rate(disk speed) supported by mobo?

I plan on replacing my current HDD with a new and bigger HDD.
For this I need to know the max data transfer rate(disk speed) that my mobo will support. However, dmidecode is not telling me that. Am I missing something?
Here's dmidecode:
# dmidecode 2.11
SMBIOS 2.5 present.
80 structures occupying 2858 bytes.
Table at 0x000F0450.
Handle 0xDA00, DMI type 218, 101 bytes
OEM-specific Type
Header and Data:
DA 65 00 DA B2 00 17 4B 0E 38 00 00 80 00 80 01
00 02 80 02 80 01 00 00 A0 00 A0 01 00 58 00 58
00 01 00 59 00 59 00 01 00 75 01 75 01 01 00 76
01 76 01 01 00 05 80 05 80 01 00 D1 01 19 00 01
00 15 02 19 00 02 00 1B 00 19 00 03 00 19 00 19
00 00 00 4A 02 4A 02 01 00 0C 80 0C 80 01 00 FF
FF 00 00 00 00
Handle 0xDA01, DMI type 218, 35 bytes
OEM-specific Type
Header and Data:
DA 23 01 DA B2 00 17 4B 0E 38 00 10 F5 10 F5 00
00 11 F5 11 F5 00 00 12 F5 12 F5 00 00 FF FF 00
00 00 00
Handle 0x0000, DMI type 0, 24 bytes
BIOS Information
Vendor: Dell Inc.
Version: A17
Release Date: 04/06/2010
Address: 0xF0000
Runtime Size: 64 kB
ROM Size: 4096 kB
Characteristics:
PCI is supported
PNP is supported
APM is supported
BIOS is upgradeable
BIOS shadowing is allowed
ESCD support is available
Boot from CD is supported
Selectable boot is supported
EDD is supported
Japanese floppy for Toshiba 1.2 MB is supported (int 13h)
3.5"/720 kB floppy services are supported (int 13h)
Print screen service is supported (int 5h)
8042 keyboard services are supported (int 9h)
Serial services are supported (int 14h)
Printer services are supported (int 17h)
ACPI is supported
USB legacy is supported
BIOS boot specification is supported
Function key-initiated network boot is supported
Targeted content distribution is supported
BIOS Revision: 17.0
Handle 0x0100, DMI type 1, 27 bytes
System Information
Manufacturer: Dell Inc.
Product Name: OptiPlex 755
Version: Not Specified
UUID: 44454C4C-5900-1050-8033-C4C04F434731
Wake-up Type: Power Switch
SKU Number: Not Specified
Family: Not Specified
Handle 0x0200, DMI type 2, 8 bytes
Base Board Information
Manufacturer: Dell Inc.
Product Name: 0PU052
Version:
Handle 0x0300, DMI type 3, 13 bytes
Chassis Information
Manufacturer: Dell Inc.
Type: Space-saving
Lock: Not Present
Version: Not Specified
Asset Tag:
Boot-up State: Safe
Power Supply State: Safe
Thermal State: Safe
Security Status: None
Handle 0x0400, DMI type 4, 40 bytes
Processor Information
Socket Designation: CPU
Type: Central Processor
Family: Xeon
Manufacturer: Intel
ID: 76 06 01 00 FF FB EB BF
Signature: Type 0, Family 6, Model 23, Stepping 6
Flags:
FPU (Floating-point unit on-chip)
VME (Virtual mode extension)
DE (Debugging extension)
PSE (Page size extension)
TSC (Time stamp counter)
MSR (Model specific registers)
PAE (Physical address extension)
MCE (Machine check exception)
CX8 (CMPXCHG8 instruction supported)
APIC (On-chip APIC hardware supported)
SEP (Fast system call)
MTRR (Memory type range registers)
PGE (Page global enable)
MCA (Machine check architecture)
CMOV (Conditional move instruction supported)
PAT (Page attribute table)
PSE-36 (36-bit page size extension)
CLFSH (CLFLUSH instruction supported)
DS (Debug store)
ACPI (ACPI supported)
MMX (MMX technology supported)
FXSR (FXSAVE and FXSTOR instructions supported)
SSE (Streaming SIMD extensions)
SSE2 (Streaming SIMD extensions 2)
SS (Self-snoop)
HTT (Multi-threading)
TM (Thermal monitor supported)
PBE (Pending break enabled)
Version: Not Specified
Voltage: 0.0 V
External Clock: 1333 MHz
Max Speed: 5200 MHz
Current Speed: 2666 MHz
Status: Populated, Enabled
Upgrade: Socket LGA775
L1 Cache Handle: 0x0700
L2 Cache Handle: 0x0701
L3 Cache Handle: Not Provided
Serial Number: Not Specified
Asset Tag: Not Specified
Part Number: Not Specified
Core Count: 2
Core Enabled: 2
Thread Count: 2
Characteristics:
64-bit capable
Handle 0x0700, DMI type 7, 19 bytes
Cache Information
Socket Designation: Not Specified
Configuration: Enabled, Not Socketed, Level 1
Operational Mode: Write Back
Location: Internal
Installed Size: 32 kB
Maximum Size: 32 kB
Supported SRAM Types:
Other
Installed SRAM Type: Other
Speed: Unknown
Error Correction Type: None
System Type: Data
Associativity: 8-way Set-associative
Handle 0x0701, DMI type 7, 19 bytes
Cache Information
Socket Designation: Not Specified
Configuration: Enabled, Not Socketed, Level 2
Operational Mode: Varies With Memory Address
Location: Internal
Installed Size: 6144 kB
Maximum Size: 6144 kB
Supported SRAM Types:
Other
Installed SRAM Type: Other
Speed: Unknown
Error Correction Type: Single-bit ECC
System Type: Unified
Associativity: <OUT OF SPEC>
Handle 0x0800, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: PARALLEL
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: DB-25 female
Port Type: Parallel Port PS/2
Handle 0x0801, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: SERIAL1
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: DB-9 male
Port Type: Serial Port 16550A Compatible
Handle 0x0802, DMI type 126, 9 bytes
Inactive
Handle 0x0803, DMI type 126, 9 bytes
Inactive
Handle 0x0804, DMI type 126, 9 bytes
Inactive
Handle 0x0805, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB1
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x0806, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB2
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x0807, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB3
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x0808, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB4
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x0809, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB5
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x080A, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB6
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x080B, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB7
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x080C, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB8
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x080D, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: ENET
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: RJ-45
Port Type: Network Port
Handle 0x080E, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: MIC
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Mini Jack (headphones)
Port Type: Audio Port
Handle 0x080F, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: LINE-OUT
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Mini Jack (headphones)
Port Type: Audio Port
Handle 0x0810, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: LINE-IN
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Mini Jack (headphones)
Port Type: Audio Port
Handle 0x0811, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: HP-OUT
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Mini Jack (headphones)
Port Type: Audio Port
Handle 0x0812, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: MONITOR
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: DB-15 female
Port Type: Video Port
Handle 0x090A, DMI type 9, 13 bytes
System Slot Information
Designation: SLOT1
Type: x1 Proprietary
Current Usage: In Use
Length: Long
Characteristics:
PME signal is supported
Handle 0x0901, DMI type 126, 13 bytes
Inactive
Handle 0x0902, DMI type 9, 13 bytes
System Slot Information
Designation: SLOT2
Type: 32-bit PCI
Current Usage: Available
Length: Long
ID: 2
Characteristics:
5.0 V is provided
3.3 V is provided
PME signal is supported
Handle 0x0903, DMI type 126, 13 bytes
Inactive
Handle 0x0904, DMI type 126, 13 bytes
Inactive
Handle 0x0905, DMI type 126, 13 bytes
Inactive
Handle 0x0906, DMI type 126, 13 bytes
Inactive
Handle 0x0907, DMI type 126, 13 bytes
Inactive
Handle 0x0908, DMI type 126, 13 bytes
Inactive
Handle 0x0A00, DMI type 10, 6 bytes
On Board Device Information
Type: Video
Status: Disabled
Description: Intel Graphics Media Accelerator 950
Handle 0x0A02, DMI type 10, 6 bytes
On Board Device Information
Type: Ethernet
Status: Enabled
Description: Intel Gigabit Ethernet Controller
Handle 0x0A03, DMI type 10, 6 bytes
On Board Device Information
Type: Sound
Status: Enabled
Description: Intel(R) High Definition Audio Controller
Handle 0x0B00, DMI type 11, 5 bytes
OEM Strings
String 1: www.dell.com
Handle 0x0D00, DMI type 13, 22 bytes
BIOS Language Information
Language Description Format: Long
Installable Languages: 1
en|US|iso8859-1
Currently Installed Language: en|US|iso8859-1
Handle 0x0F00, DMI type 15, 29 bytes
System Event Log
Area Length: 2049 bytes
Header Start Offset: 0x0000
Header Length: 16 bytes
Data Start Offset: 0x0010
Access Method: Memory-mapped physical 32-bit address
Access Address: 0xFFF01000
Status: Valid, Not Full
Change Token: 0x00000018
Header Format: Type 1
Supported Log Type Descriptors: 3
Descriptor 1: POST error
Data Format 1: POST results bitmap
Descriptor 2: System limit exceeded
Data Format 2: System management
Descriptor 3: Log area reset/cleared
Data Format 3: None
Handle 0x1000, DMI type 16, 15 bytes
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: None
Maximum Capacity: 8 GB
Error Information Handle: Not Provided
Number Of Devices: 4
Handle 0x1100, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x1000
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 1024 MB
Form Factor: DIMM
Set: None
Locator: DIMM_1
Bank Locator: Not Specified
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz
Manufacturer: AD00000000000000
Handle 0x1101, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x1000
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 1024 MB
Form Factor: DIMM
Set: None
Locator: DIMM_3
Bank Locator: Not Specified
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz
Handle 0x1102, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x1000
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 1024 MB
Form Factor: DIMM
Set: None
Locator: DIMM_2
Bank Locator: Not Specified
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz
Handle 0x1103, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x1000
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 1024 MB
Form Factor: DIMM
Set: None
Locator: DIMM_4
Bank Locator: Not Specified
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz
Handle 0x1300, DMI type 19, 15 bytes
Memory Array Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x000FDFFFFFF
Range Size: 4064 MB
Physical Array Handle: 0x1000
Partition Width: 1
Handle 0x1400, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0007FFFFFFF
Range Size: 2 GB
Physical Device Handle: 0x1100
Memory Array Mapped Address Handle: 0x1300
Partition Row Position: 1
Interleave Position: 1
Interleaved Data Depth: 1
Handle 0x1401, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00080000000
Ending Address: 0x000FDFFFFFF
Range Size: 2016 MB
Physical Device Handle: 0x1101
Memory Array Mapped Address Handle: 0x1300
Partition Row Position: 1
Interleave Position: 1
Interleaved Data Depth: 1
Handle 0x1402, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0007FFFFFFF
Range Size: 2 GB
Physical Device Handle: 0x1102
Memory Array Mapped Address Handle: 0x1300
Partition Row Position: 1
Interleave Position: 2
Interleaved Data Depth: 1
Handle 0x1403, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00080000000
Ending Address: 0x000FDFFFFFF
Range Size: 2016 MB
Physical Device Handle: 0x1103
Memory Array Mapped Address Handle: 0x1300
Partition Row Position: 1
Interleave Position: 2
Interleaved Data Depth: 1
Handle 0x1410, DMI type 126, 19 bytes
Inactive
Handle 0x1800, DMI type 24, 5 bytes
Hardware Security
Power-On Password Status: Enabled
Keyboard Password Status: Not Implemented
Administrator Password Status: Enabled
Front Panel Reset Status: Not Implemented
Handle 0x1900, DMI type 25, 9 bytes
System Power Controls
Next Scheduled Power-on: *-* 00:00:00
Handle 0x1B10, DMI type 27, 12 bytes
Cooling Device
Type: Fan
Status: OK
OEM-specific Information: 0x0000DD00
Handle 0x1B11, DMI type 27, 12 bytes
Cooling Device
Type: Fan
Status: OK
OEM-specific Information: 0x0000DD01
Handle 0x1B12, DMI type 126, 12 bytes
Inactive
Handle 0x1B13, DMI type 126, 12 bytes
Inactive
Handle 0x1B14, DMI type 126, 12 bytes
Inactive
Handle 0x2000, DMI type 32, 11 bytes
System Boot Information
Status: No errors detected
Handle 0x8100, DMI type 129, 8 bytes
OEM-specific Type
Header and Data:
81 08 00 81 01 01 02 01
Strings:
Intel_ASF
Intel_ASF_001
Handle 0x8200, DMI type 130, 20 bytes
OEM-specific Type
Header and Data:
82 14 00 82 24 41 4D 54 01 01 00 00 01 A5 0B 02
00 00 00 00
Handle 0x8300, DMI type 131, 64 bytes
OEM-specific Type
Header and Data:
83 40 00 83 14 00 00 00 00 00 C0 29 05 00 00 00
F8 00 4E 24 00 00 00 00 0D 00 00 00 02 00 03 00
19 04 14 00 01 00 01 02 C8 00 BD 10 00 00 00 00
00 00 00 00 FF 00 00 00 00 00 00 00 00 00 00 00
Handle 0x8800, DMI type 136, 6 bytes
OEM-specific Type
Header and Data:
88 06 00 88 5A 5A
Handle 0xD000, DMI type 208, 10 bytes
OEM-specific Type
Header and Data:
D0 0A 00 D0 01 03 FE 00 11 02
Handle 0xD100, DMI type 209, 12 bytes
OEM-specific Type
Header and Data:
D1 0C 00 D1 78 03 07 03 04 0F 80 05
Handle 0xD200, DMI type 210, 12 bytes
OEM-specific Type
Header and Data:
D2 0C 00 D2 F8 03 04 03 06 80 04 05
Handle 0xD201, DMI type 126, 12 bytes
Inactive
Handle 0xD400, DMI type 212, 242 bytes
OEM-specific Type
Header and Data:
D4 F2 00 D4 70 00 71 00 00 10 2D 2E 42 00 11 FE
01 43 00 11 FE 00 0F 00 25 FC 00 10 00 25 FC 01
11 00 25 FC 02 12 00 25 FC 03 00 00 25 F3 00 00
00 25 F3 04 00 00 25 F3 08 00 00 25 F3 0C 07 00
23 8F 00 08 00 23 F3 00 09 00 23 F3 04 0A 00 23
F3 08 0B 00 23 8F 10 0C 00 23 8F 20 0E 00 23 8F
30 0D 00 23 8C 40 A6 00 23 8C 41 A7 00 23 8C 42
05 01 22 FD 02 06 01 22 FD 00 8C 00 22 FE 00 8D
00 22 FE 01 9B 00 25 3F 40 9C 00 25 3F 00 09 01
25 3F 80 A1 00 26 F3 00 A2 00 26 F3 08 A3 00 26
F3 04 9F 00 26 FD 02 A0 00 26 FD 00 9D 00 11 FB
04 9E 00 11 FB 00 54 01 23 7F 00 55 01 23 7F 80
5C 00 78 BF 40 5D 00 78 BF 00 04 80 78 F5 0A 01
A0 78 F5 00 93 00 7B 7F 80 94 00 7B 7F 00 8A 00
37 DF 20 8B 00 37 DF 00 03 C0 67 00 05 FF FF 00
00 00
Handle 0xD401, DMI type 212, 172 bytes
OEM-specific Type
Header and Data:
D4 AC 01 D4 70 00 71 00 03 40 59 6D 2D 00 59 FC
02 2E 00 59 FC 00 6E 00 59 FC 01 E0 01 59 FC 03
28 00 59 3F 00 29 00 59 3F 40 2A 00 59 3F 80 2B
00 5A 00 00 2C 00 5B 00 00 55 00 59 F3 00 6D 00
59 F3 04 8E 00 59 F3 08 8F 00 59 F3 00 00 00 55
FB 04 00 00 55 FB 00 23 00 55 7F 00 22 00 55 7F
80 F5 00 58 BF 40 F6 00 58 BF 00 EB 00 55 FE 00
EA 00 55 FE 01 40 01 54 EF 00 41 01 54 EF 10 ED
00 54 F7 00 F0 00 54 F7 08 4A 01 53 DF 00 4B 01
53 DF 20 4C 01 53 7F 00 4D 01 53 7F 80 68 01 56
BF 00 69 01 56 BF 40 FF FF 00 00 00
Handle 0xD402, DMI type 212, 152 bytes
OEM-specific Type
Header and Data:
D4 98 02 D4 70 00 71 00 00 10 2D 2E 2D 01 21 FE
01 2E 01 21 FE 00 97 00 22 FB 00 98 00 22 FB 04
90 00 11 CF 00 91 00 11 CF 20 92 00 11 CF 10 E2
00 27 7F 00 E3 00 27 7F 80 E4 00 27 BF 00 E5 00
27 BF 40 D1 00 22 7F 80 D2 00 22 7F 00 45 01 22
BF 40 44 01 22 BF 00 36 01 21 F1 06 37 01 21 F1
02 38 01 21 F1 00 39 01 21 F1 04 2B 01 11 7F 80
2C 01 11 7F 00 4E 01 65 CF 00 4F 01 65 CF 10 D4
01 65 F3 00 D5 01 65 F3 04 D2 01 65 FC 00 D3 01
65 FC 01 FF FF 00 00 00
Handle 0xD403, DMI type 212, 157 bytes
OEM-specific Type
Header and Data:
D4 9D 03 D4 70 00 71 00 03 40 59 6D 17 01 52 FE
00 18 01 52 FE 01 19 01 52 FB 00 1A 01 52 FB 04
1B 01 52 FD 00 1C 01 52 FD 02 1D 01 52 F7 00 1E
01 52 F7 08 1F 01 52 EF 00 20 01 52 EF 10 21 01
52 BF 00 22 01 52 BF 40 87 00 59 DF 20 88 00 59
DF 00 E8 01 66 FD 00 E9 01 66 FD 02 02 02 53 BF
00 03 02 53 BF 40 04 02 53 EF 00 05 02 53 EF 10
06 02 66 DF 00 07 02 66 DF 20 08 02 66 EF 00 09
02 66 EF 10 17 02 66 F7 00 18 02 66 F7 08 44 02
52 BF 40 45 02 52 BF 00 FF FF 00 00 00
Handle 0xD800, DMI type 126, 9 bytes
Inactive
Handle 0xDD00, DMI type 221, 19 bytes
OEM-specific Type
Header and Data:
DD 13 00 DD 00 01 00 00 00 10 F5 00 00 00 00 00
00 00 00
Handle 0xDD01, DMI type 221, 19 bytes
OEM-specific Type
Header and Data:
DD 13 01 DD 00 01 00 00 00 11 F5 00 00 00 00 00
00 00 00
Handle 0xDD02, DMI type 221, 19 bytes
OEM-specific Type
Header and Data:
DD 13 02 DD 00 01 00 00 00 12 F5 00 00 00 00 00
00 00 00
Handle 0xDE00, DMI type 222, 16 bytes
OEM-specific Type
Header and Data:
DE 10 00 DE C1 0B 00 00 10 05 19 21 01 00 00 01
Handle 0x7F00, DMI type 127, 4 bytes
End Of Table
Hdparm also does not tell me the max data transfer rate (disk speed) of my current drive although this link : www.wdc.com/en/library/sata/2879-001146.pdf says that it is 3.0Gb/s
and here's hdparm -I /dev/sda
/dev/sda:
ATA device, with non-removable media
Model Number: WDC WD800JD-75JNC0
Firmware Revision: 06.01C06
Standards:
Supported: 6 5 4
Likely used: 8
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
CHS current addressable sectors: 16514064
LBA user addressable sectors: 156250000
Logical/Physical Sector size: 512 bytes
device size with M = 1024*1024: 76293 MBytes
device size with M = 1000*1000: 80000 MBytes (80 GB)
cache/buffer size = 8192 KBytes
Capabilities:
LBA, IORDY(can be disabled)
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 8
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* DOWNLOAD_MICROCODE
SET_MAX security extension
Automatic Acoustic Management feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* SMART error logging
* SMART self-test
* Gen1 signaling speed (1.5Gb/s)
* Host-initiated interface power management
* SMART Command Transport (SCT) feature set
* SCT Long Sector Access (AC1)
* SCT LBA Segment Access (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
Checksum: correct
Last edited by Inxsible (2011-03-27 04:40:49)

I just checked my BIOS and my current setting is set at IDE although it also mentions that the default should be AHCI. Currently I have a dual boot of Windows 7 (need it for Tax software) and Arch
So I guess, when I get the new HDD, I will first set it to AHCI and then install the OSes on it. See if NCQ helps any, and if not I will turn it back and re-install (if I have to). I am planning to have Windows only in virtualbox in the new drive.
Anyhoo, while I was in the BIOS I found two things which I had questions about :
1) Under Onboard Devices --> Integrated NIC , my setting is currently set at "On w/PXE" and it says the default should be just "On". Would it be ok to change it back to On since its a single machine and its not booting an OS on any server. I just don't want to have to re-install anything now since I will be doing that in the new HDD.
2) How would I know whether my BIOS would support a 64 bit OS in Virtualbox? I checked some setting under Virtualization, but they weren't very clear.
I will edit this post and let you know exactly what settings were present under the Virtualization sub-section.

Determining Data transfer rate through modem in java

Hi,
I want to write an application in java which will communicate with
connected modem of the system and it will detect the data transfer rate.
I want to know how much data is transferring(upload/download)through modem and in a specific time how much data is transferred.
I will give some max upload/downloading limit for a specific time and if data transfer exceeds that limit,it will show message.
e.g if i fix max upload/download data transfer limit by the modem is say 10GB/20GB for a specific time span say for 15 days.Then my program automatically will start when the Modem will be connected and keep a log of data transfer(upload/download)and if data transfer goes beyond limit then it will show message.Also i would be able to see how much data is transferred for any specific day.
I want to know this type of application is possible in java.If yes then
which API's i need to use.
If this type of program is available in some site in other language then also i will be helpful.Pl give the links.
byeeeeeeee
Pradipto

Hi,
i want to do it in java only to explore the power of
java.I agree with Abuse, Java is not designed for such applications. I'm not even sure if you can solve your problems with Java.

Vista Beta 2 (v5472) + K9N SLI Platinum

Has anyone managed to get Vista installed from scratch with the "K9N SLI Platinum"?
I tried, 32bit and 64bit. both failed.

I got Vista Beta 2 32-bit installed on K9N Ultra + 4200+ X2, but because of the poweroff-issues of K9N-series, Vista was really unstable. Well, my mobo is RMA'd now, so let's see how's gonna work with the new revision.

Difference in data transfer rates between winXP and Linux server?

Hello all,
I am using a winXP laptop to act as my server (all usb external hard drives are connected to it) but the data transfer rates can be really slow. Is Linux faster in that regard? Can a Linux based server provide faster data transfer rates?
Thanks for any help.
Bmora96

Linux cannot make hardware go any faster - so if WinXP and its drivers are making optimal use of those USB drives and the USB data transfer pipe, Linux will not make it faster. (but installing Linux and going Tux are always excellent ideas that need no real reason either ;-) )
Real question you should be asking is if using a notebook in a server role is wise thing to do?

Disk data transfer rate - iMac 2013

Good morning Apple fellows
First of all, sorry for my troubled English speaking, I'll do my best to explain the issue I'm having in the best way possible.
Yesterday I finally received my new iMac (I'm a proud Apple user since 2006), the machine has these specifications: 16 GB Ram, i7 processor, nVidia GT 780M, and a SSD drive of 1TB of capacity.
Under Mavericks everything runs smooth and fine, no issues at all, just perfect, the fastest machine I've ever had. Unfortunately, I had to install Windows 7 via Bootcamp (I'm a mechanical engineer and I use Autodesk Inventor to do my stuff).
After completing the installation of the Microsoft OS, I instantly noticed some laggy performance while running Windows: I installed as asked all the Bootcamp drivers with the USB pendrive that I prepared, but both the startup of the system and the normal use were a bit slow, even slower than my old '09 iMac.
In order to understand what the problem was, I ran the system performance test included in Windows: all the ratings I have are maxed out at 7.9 (7.9 is the top I think), in exception of the "Disk Data Transfer Rate", that is 5.9. As far as I remember, this value is typical for a mechanical disk drive, not for an SSD drive supported with PCIe connections.
Does anybody here got a similar issue? Is there any driver package that I have to install in addition to the Bootcamp drivers?
Thanks in advance

That is because the WEI uses your boot disk as the default device to measure performance, and, for instance, a Velociraptor 10 K disk, does not score more than 5.9. The story changes when the test is run on other disks, like my array:
However, this measurement is totally worthless in real life. You should look at practical benchmarks like PPBM5 Benchmark

K9N SLI Platinum MS7250 ver1.1 ... need help with Windows 7 install

Hello,
Having an intermittant issue with Windows 7 32bit. During startup Windows 7 gets stuck at the logo screen. Not always though. Every 7-8th reboot it will make it past and go all the way into Windows 7. I've tried all sorts of combinations of "ebabling/disabling". This system ran XP professional for 3 years without any issues. Currently, I have the most luck by connecting the keyboard and mouse to PS2 and leaving USB disabled. This may not be the issue though. Once I got Win7 to boot I performed driver updates etc.
If someone has suggestions please let me know. I'm about to try the USB bios flash but have never done it before.
Thank you,
BK
CPU: AMD 64 x2 5000+
RAM: 4GB Patriot Viper Series -- set to 2.1V per specs, 800MHz, setup in Dual Channel mode
Video: NVidia GeForce 7900GS
PSU: 600Watt CoolerMaster ATX12V 12volt rails push around 18amps and I'm using the additional power port for power to the video card
Bios ver: 1.3 (this is what shows on the splash screen at startup however CPUID shows 080014 - not sure what that means)
Motherboard: K9N SLI Platinum MS7250 ver1.1

Hi Guys,
Thank you for the replies.
- Yes it is a fresh install of Windows7 on a drive that originally had XP Pro
- If I boot into safe mode it does go into Win7 most of the time.
- I posted on the MSI tech support page (http://support.msi.com/index.php) and the response was to upgrade the BIOS. What do you think?
- I've been using this graphics card for three years and is nowhere near as powerful as what's out there now. In fact all of the components are three years old except the RAM
- I tried the old RAM (2GB Corsair) and it also had the same issue. Even at default RAM settings or otherwise. Now I'm back to the 4GB Patriot Vipers.
- What is this capacitor problem people are referring to? Is it a problem specifically on this model board?
Thank you..
BK

Limit Hyper-V Replication Data Transfer Rate

Hello,
i need to limit data transfer rate for Hyper-v replication because between two Datacenter have bandwidth limitation.
Please suggest

You can use the New-NetQoSPolicy cmdlet to set the throttling limits -
http://technet.microsoft.com/en-us/library/hh967468.aspx. Based on the destination port (the port on which the replica server has been configured to receive replication traffic - maybe it's port 80 in your case) or the destination subnet, you can specify
a throttling value (-ThrottleRateActionBitsPerSecond) or assign a weight (MinBandwidthWeightAction).
Eg: New-NetQosPolicy "Replica traffic to 8080" –DestinationPort 8080 –ThrottleRateActionBitsPerSecond 100000
or check the link to Thomas blog
http://www.thomasmaurer.ch/2013/12/throttling-hyper-v-replica-traffic/

Low data transfer between my iMac & Time Capsule

Hello,
I have just purchased 1GB Time Capsule yesterday to get a back-up of my iMac HDD, and also to use it as an external HDD. I was much interested by the wireless functions.
After the installation, Time Machine started to save a back-up of my HDD (more than 200GB). But after one full night, only 7GB out of 220GB was transfered wireless.
With a so low data transfer, it will take 20 days for the full back-up.
Is it normal ?
Do I have to make the first back-up though ethernet (wired) ?
I am working on big video files (xx GB), so I really need to increase the speed of data transfer. Is there someting to change in the settings ?
Thank you for your help, it will be highly appreciated...
Regards,
Jean-Philippe, Paris, France

Hello,
I have just purchased 1GB Time Capsule yesterday to get a back-up of my iMac HDD, and also to use it as an external HDD. I was much interested by the wireless functions.
After the installation, Time Machine started to save a back-up of my HDD (more than 200GB). But after one full night, only 7GB out of 220GB was transfered wireless.
With a so low data transfer, it will take 20 days for the full back-up.
Is it normal ?
Do I have to make the first back-up though ethernet (wired) ?
I am working on big video files (xx GB), so I really need to increase the speed of data transfer. Is there someting to change in the settings ?
Thank you for your help, it will be highly appreciated...
Regards,
Jean-Philippe, Paris, France

K9N SLI Platinum Power off issue when burning CD/DVD

MSI K9N SLI Platinum
AMD Athlon64 X2 4200
2x 1Gb Kingsten DDR2 Dual Channel
2x 256Mb nvidia 7600GS on SLI
1x 160Gb seagate SATA HDD
1x 250G seagate SATA HDD
1xDVD Rom
1xDVD-RW
750W Thermaltake Toughpower PSU
The problem what I'm getting is when I'm try to burn a DVD or CD... my PC shuts like you unplugged your power (not restarting)
first I thought something wrong with my DVD burner then I tried with a new one(had a ASUS one and switched to LITE-on).. but still happening.. I have update the BIOS v1.3 as well..but didn't do any changes.. My DVD-RW connected to IDE controller.. that's only thing controlled by IDE.. don know how to fix this... I'm sure it can't be the PSU.. I changed my PSU 500W to 750W because of this matter.. I guess something wrong with the IDE controller.. only MSI can fix this... I'm waiting for a reply from them ... Please post if you having the same problem..thx

HEY GUYS FINALLY GOT A ANSWER FROM MSI Co.
According to this best thing is RMA..
Dear Kamal,
We have fixed this issue by changing C565 from 100pF to 220pF. All the stock had been reworked, and we have informed all the MSI™ Distributor locators.
So please get your MB for RMA.
As to the RMA, The normal procedure is to contact your reseller (the place you bought the board from) for repair/exchange , If the reseller for some reason like bankrupt cannot be contacted, then contact MSI distributor http://www.msi.com.tw/program/contact/where2buy/ or MSI office near your place http://www.msi.com.tw/program/about/w2b/index.php
Sorry for any inconveniency.
Best wishes,
MSI Technical Support Team

K9N SLI Platinum reboots while playing games

Hello,
System config
Athlon 64 3800+ x2
K9N SLI Platinum (Bios version 1.1)
2 * 1024 ocz 6400 gold memory
80 gig sata 1 drive
nec dual layer burner
Xfx 7600 gt xxx
floppy
PSU Coolmax AP-450 (CX-400)
The system is stable when I browse email and such, but as soon as I play games I'm getting reboots. Blue screen of death a couple times. I bought a couple more fans for my case (waiting to see if it makes a difference when it arrives). It may be getting to hot. I have been reading and perhaps the PSU is not good enough or compatible. I haven't checked the memory yet, But i would think that it would reboot consistantly not just in games if that were a problem. Does anyone have a solution for me?
Thanks,
LTBob

Quote from: eddie_g on 19-July-06, 19:06:28
I had the same problems as you have.
The fix I did was, downloaded the drivers for AMD dual core processors from the AMD website.
Make sure you have your RAM set to 2.1V.
It's nothing to do with the PSU.
"It's nothing to do with the PSU."
cant agree, there is alot of issues with the same symptoms. it may crap or overload PSU also.

K9n SLI Platinum + 4x1GB = Cold

Got som problems running my K9n SLI platinum with 2x VS2GBKIT667D2 (= 4x1GB dimms)
With 2x1GB DIMMs , it works fine, in any DIMM slots.
But when i put in all 4 of them I got Major Freezing problems.
Memtest86+ works fine.
But in XP it freezez, in Vista it freezes.
Trying to install Vista with 4GB it freezes before the installation program even starts..
Any helpfull thoughts?

V-ICE, there are at least 3 more people (myself included) who are having this "HT sync flood" error. All of us have K9N motherboards with V1.7 BIOS:
- K9N SLI Platinum + BIOS 7250v17 (V-ICE)
- K9N SLI Platinum + BIOS 7250v17 (TomMe)
- K9N4 Ultra-F + BIOS 7310v17 (zzkey)
- K9N Platinum + BIOS 7250v17 (Grawp)
I think there is a problem with those BIOS versions. I've had 3 K9N SLI Platinum boards, never had that error before. Only with my latest board + v1.7 BIOS.
Have you had any "overclock failed" messages so far?

K9N SLI PLATINUM low data transfer rate

Similar Messages

Maybe you are looking for