K9N SLI Platinum operating system problems

I have a MSI K9N SLI plat MB, an AMD 64 x2 4200 cpu, a EVGA nvidia 7600GS video card and 2gb mem.
My problem is that I am unable to get windows XP, XP64, or Vista to run on my IDE hard drive.
I am running XP from an SATA HD and it works OK. I have a CD/DVD and IDE HD on the IDE controller.
Updated BIOS to 1.3, no help.

Quote from: don_mccarter on 24-August-06, 14:16:44
I have a MSI K9N SLI plat MB, an AMD 64 x2 4200 cpu, a EVGA nvidia 7600GS video card and 2gb mem.
My problem is that I am unable to get windows XP, XP64, or Vista to run on my IDE hard drive.
I am running XP from an SATA HD and it works OK. I have a CD/DVD and IDE HD on the IDE controller.
Updated BIOS to 1.3, no help.
==============================
Trouble here too
My system bit similer to your one:
MSI K9N SLI Platinum
AMD Athlon64 X2 4200
2x 1Gb Kingsten DDR2 Dual Channel
2x 256Mb nvidia 7600GS on SLI
1x 160Gb SATA HDD
1x 250G SATA HDD
1xDVD Rom
1xDVD-RW
750W Thermaltake Toughpower PSU
The problem what I'm getting is when I'm try to burn a DVD or CD... my PC shuts like you unplugged your power (not restarting)
first I thought something wrong with my DVD burner then I tried with a new one(had ASUS one now having LITE-on).. but still happening.. I have update the BIOS v1.3 as well..but didn't do any changes.. My DVD-RW connected to IDE controller.. that's only thing controlled by IDE.. don know how to fix this... I'm sure it can't be the PSU.. I changed my PSU 500W to 750W because of this matter.. I guess something wrong with the IDE controller.. only MSI can fix this... I'm waiting for a reply from them... :(
Kamal

Similar Messages

K9N SLI Platinum - RAID 0 problems

Hi everyone,
I've just assembled a new pc with a K9N SLI Platinum (PCB Ver: 1.1; BIOS Ver: 1.3), 1GB (2x512MB DIMM1 & 3) Kingston KVR667, 2 Maxtor SATA-II disks, GF 7300GS with 256MB DDR2.
I'm able to install windows with one disk but can't do it with both disks setup as raid 0.
I've tried both Sata Raid Driver from cd and from MSI website.
With the driver from the cd windows setup finds the raid and starts installation, but freezes somewhere (totally random) without finishing.
With the driver downloaded from the website windows setup can't find the raid.
Any hints?
Thanks

Quote from: manuelmont on 25-September-06, 07:13:09
I tried once again to install windows and this time setup finished successfully and the computer boots from the raid. So my first question: what is the relation between the bootable option at the raid setup and the fact that the system booted without it?
I doubt that the removal of the floppy from the bootable devices list has anything to do with the successful install...
Well if it is grayed out in the RAID setup is because it is already Bootable, as for the removal of the floppy from the bootable devices, there are things that only the gods of the computers know...
Quote from: manuelmont on 25-September-06, 07:13:09
Everything seemed to work ok but the computer started to freeze once again during installation of other software which made the system unstable.
Then I replace the graphics card with an ATI X300 (just for testing) and the system became stable. I installed software, played some games without problems. As the GF 7300GS I removed works on another pc this seems to be some compatibility problem between the MB and the GF (turbocache?).
I used Sisoft Sandra 2007 Lite to test/benchmark the system. All the tests were almost normal (except memory - benchmark showed values a bit lower than I expected!) but I could not run Physical Disks Benchmark module neither Physical Disks Hardware module (but could benchmark the file system). What does this mean?
The disks are in fact DiamonMax 17 (6G160E0) but I'll try another brand as well, these are the only disks. On the IDE channel I only have one dvd recorder.
Your PSU has way to low amperage for that system, the test is the change you made from a superior GFX to a lower end one, the NX7300GS eats alot of amps in comparison to the X300, and it does not have nothing to do with the TurboCache feature.
As for Sisoft Sandra I don't use that "I'm a potty mouth" (pardon my french ) I use Lavalys Everest or for disks HDtach, and others.
You could not test the physical disks because they are in RAID mode, but you can test or benchmark the logical disks because they are the partitions you created in the physical disks and are divided by the 2 disks, half in one half in the other...
I hope this will shed some light into the questions...
Be well....

K9N SLI Platinum MS7250 ver1.1 ... need help with Windows 7 install

Hello,
Having an intermittant issue with Windows 7 32bit. During startup Windows 7 gets stuck at the logo screen. Not always though. Every 7-8th reboot it will make it past and go all the way into Windows 7. I've tried all sorts of combinations of "ebabling/disabling". This system ran XP professional for 3 years without any issues. Currently, I have the most luck by connecting the keyboard and mouse to PS2 and leaving USB disabled. This may not be the issue though. Once I got Win7 to boot I performed driver updates etc.
If someone has suggestions please let me know. I'm about to try the USB bios flash but have never done it before.
Thank you,
BK
CPU: AMD 64 x2 5000+
RAM: 4GB Patriot Viper Series -- set to 2.1V per specs, 800MHz, setup in Dual Channel mode
Video: NVidia GeForce 7900GS
PSU: 600Watt CoolerMaster ATX12V 12volt rails push around 18amps and I'm using the additional power port for power to the video card
Bios ver: 1.3 (this is what shows on the splash screen at startup however CPUID shows 080014 - not sure what that means)
Motherboard: K9N SLI Platinum MS7250 ver1.1

Hi Guys,
Thank you for the replies.
- Yes it is a fresh install of Windows7 on a drive that originally had XP Pro
- If I boot into safe mode it does go into Win7 most of the time.
- I posted on the MSI tech support page (http://support.msi.com/index.php) and the response was to upgrade the BIOS. What do you think?
- I've been using this graphics card for three years and is nowhere near as powerful as what's out there now. In fact all of the components are three years old except the RAM
- I tried the old RAM (2GB Corsair) and it also had the same issue. Even at default RAM settings or otherwise. Now I'm back to the 4GB Patriot Vipers.
- What is this capacitor problem people are referring to? Is it a problem specifically on this model board?
Thank you..
BK

K9N SLI Platinum reboots while playing games

Hello,
System config
Athlon 64 3800+ x2
K9N SLI Platinum (Bios version 1.1)
2 * 1024 ocz 6400 gold memory
80 gig sata 1 drive
nec dual layer burner
Xfx 7600 gt xxx
floppy
PSU Coolmax AP-450 (CX-400)
The system is stable when I browse email and such, but as soon as I play games I'm getting reboots. Blue screen of death a couple times. I bought a couple more fans for my case (waiting to see if it makes a difference when it arrives). It may be getting to hot. I have been reading and perhaps the PSU is not good enough or compatible. I haven't checked the memory yet, But i would think that it would reboot consistantly not just in games if that were a problem. Does anyone have a solution for me?
Thanks,
LTBob

Quote from: eddie_g on 19-July-06, 19:06:28
I had the same problems as you have.
The fix I did was, downloaded the drivers for AMD dual core processors from the AMD website.
Make sure you have your RAM set to 2.1V.
It's nothing to do with the PSU.
"It's nothing to do with the PSU."
cant agree, there is alot of issues with the same symptoms. it may crap or overload PSU also.

K9N SLI PLATINUM low data transfer rate

Hi, (sorry for my pour english) I had to go back to Winxp native SATA/IDE drivers and my pc crash & BSOD problem it's gone! :D (BSOD when i install some programs or some games, listening music and moving data at the same time, etc.) now i'm available to execute multitasks without any troubles. But now the transference it's quite poor , I think this is an easy and temporary solution for this big problem.
I bought my PC on 2006 and the Windows XP drivers are from 2001, aren't new Nvidia/MSI drivers to fix this annoying problem?
Thanks.
AM2 3800+ X2
MSI K9N SLI PLATINUM, bios 1.4
2 x 1GB OCZ DDR2 6400 Platinum
PSU PowerCooler 550w
HD WD3200 SATAII
NX7900GT

I've got nearly the same problem, but a little worse. My data transfer rate seems very slow for a 100mb network and if I start copying files over the network, after only a couple of megs I lose connectivity to the network completely! I've removed the network cable and windows notices this, and when I put it back in windows also notices the change, but the green and orange lights on the port itself stay on solid. If I reboot windows everything comes back. I don't have problems browsing the web, seems to only happen when the ethernat port is running close to full load (for the connection speed of 100mb as apposed to 1gb).
Anyone else seen this? I'm on the latest drivers, the latest bios and I've tried disabling on of the network ports in the bios but his didn't work.
Kevpatts

K9N SLI Platinum Power off issue when burning CD/DVD

MSI K9N SLI Platinum
AMD Athlon64 X2 4200
2x 1Gb Kingsten DDR2 Dual Channel
2x 256Mb nvidia 7600GS on SLI
1x 160Gb seagate SATA HDD
1x 250G seagate SATA HDD
1xDVD Rom
1xDVD-RW
750W Thermaltake Toughpower PSU
The problem what I'm getting is when I'm try to burn a DVD or CD... my PC shuts like you unplugged your power (not restarting)
first I thought something wrong with my DVD burner then I tried with a new one(had a ASUS one and switched to LITE-on).. but still happening.. I have update the BIOS v1.3 as well..but didn't do any changes.. My DVD-RW connected to IDE controller.. that's only thing controlled by IDE.. don know how to fix this... I'm sure it can't be the PSU.. I changed my PSU 500W to 750W because of this matter.. I guess something wrong with the IDE controller.. only MSI can fix this... I'm waiting for a reply from them ... Please post if you having the same problem..thx

HEY GUYS FINALLY GOT A ANSWER FROM MSI Co.
According to this best thing is RMA..
Dear Kamal,
We have fixed this issue by changing C565 from 100pF to 220pF. All the stock had been reworked, and we have informed all the MSI™ Distributor locators.
So please get your MB for RMA.
As to the RMA, The normal procedure is to contact your reseller (the place you bought the board from) for repair/exchange , If the reseller for some reason like bankrupt cannot be contacted, then contact MSI distributor http://www.msi.com.tw/program/contact/where2buy/ or MSI office near your place http://www.msi.com.tw/program/about/w2b/index.php
Sorry for any inconveniency.
Best wishes,
MSI Technical Support Team

MSI K9N SLI Platinum - SATA not hot-swappable?

can i get a confirmation that K9N SLI Platinum motherboard does NOT support hot-swapping the SATA drives. I switched to this board for the AM2 socket and now i am not seeing the removable drive bays as hot-swappable (ie. no green arrow down by the clock). maybe i am missing a bios setting?

jackaninny
Quote
I check two machines today and one is just fine using the removable trays and any drives we put in there show up in the 'safely remove hardware' tool. the other machines does NOT detect any drives inserted while the machine is powered on and something else - under the 'policies' tab the top two choices ('optimize for quick removal' instead of 'optimize for performance') are greyed out but there is an option below them that i can check and uncheck (i cannot remember the exact title of this option).
I assume you are trying the same drives when you swap the removable trays between the two machines. Some drives have a jumper that has to be removed to enable SATA II operation, so if they aren't the same physical drives you might want to check that.
I think the stuff below the greyed out area in your 'Policies' tab is a check box that enables/disables write caching. You might want to try checking/unchecking that.
Also, you should check out the IDE/ATA Controller selection in the Device Manager. Take a look at each instance of controller that shows up there. SATA controllers actually a primary and secondary channel and each channel has a master and a slave drive, just like old IDE controllers. Look at each tab on both machines and make sure all of the drive's features are set identically on these tabs. Sometimes Windows can try to outsmart you. For example, I have an SATA II Maxtor drive that has its transfer mode downgraded to SATA I by Windows (there is a little yellow triangle with a '!' in the middle of the lower part of the panel). The help balloon for this arrtibutes it to 'excessive transfer errors.' I haven't tried to chase that one down yet, however.
As far as setting the machines up the same way, sometimes the sequence of driver installations can have an effect. For example, a RAID driver installed during Windows setup using the 'F6 - install other driver' option can behave differently from one installed with the Device Manager 'Update Driver' function.
Sorry I can't be of more help here.
Maybe someone else in this forum is a bit more knowledgable on the subject.
ss

K9n SLI Platinum + 4x1GB = Cold

Got som problems running my K9n SLI platinum with 2x VS2GBKIT667D2 (= 4x1GB dimms)
With 2x1GB DIMMs , it works fine, in any DIMM slots.
But when i put in all 4 of them I got Major Freezing problems.
Memtest86+ works fine.
But in XP it freezez, in Vista it freezes.
Trying to install Vista with 4GB it freezes before the installation program even starts..
Any helpfull thoughts?

V-ICE, there are at least 3 more people (myself included) who are having this "HT sync flood" error. All of us have K9N motherboards with V1.7 BIOS:
- K9N SLI Platinum + BIOS 7250v17 (V-ICE)
- K9N SLI Platinum + BIOS 7250v17 (TomMe)
- K9N4 Ultra-F + BIOS 7310v17 (zzkey)
- K9N Platinum + BIOS 7250v17 (Grawp)
I think there is a problem with those BIOS versions. I've had 3 K9N SLI Platinum boards, never had that error before. Only with my latest board + v1.7 BIOS.
Have you had any "overclock failed" messages so far?

Need to buy a MSI K9N SLI Platinum I/O Back Plate, But where ?

Where can I buy a I/O back plate for a MSI K9N SLI Platinum Motherboard in the Uk online
I've looked on ebay, but most are standard design,,, have email MSI, but no reply so far
Thanks for any help.......
Regards
NC ........

Quote from: nuttycomputer on 25-April-07, 19:40:40
Russell.......
Rang MSI in the UK and they gave me an email address:
[email protected]
And they emailed me back with the following message:
Hi,
We have in stock E21-7030012-A91 and we will send you the item free of charge.
Please provide full delivery address.
Best Regards,
MSI (UK) Returns Department
(non-direct customers)
UK - www.msicomputer.co.uk
HQ - www.msi.com.tw
Thanks Russell for your help !!
No problem, I'm glad I could help.
They are a great bunch of guys, last time I called we ended up talking for almost a hour, about various things
Russell.

Orange slot in MSI K9N SLI Platinum

Quick and Dirty:
What cards can I use in the Orange slot for in the K9N SLI Platinum?
Details:
I currently have the K8N Neo4 Platinum and am upgrading from 939 to socket AM2. I want the K9N SLI Platinum board but NEED 3 PCI slots. The three cards I need are Promise Ultra ATA/133 card, Soundblaster X-Fi sound card, Belkin wireless G LAN card. The K9N has three slots but that INCLUDES the orange slot but I don't know what its for.
I tried the wireless card in the orange slot but i can't get the drivers to install and "accept" the card. Works fine when I switch back to white slot. I'm afraid without 3 slots I cannot purchase the board. Any solutions?

Tried:
Raid card installed without a hitch, first time installing that in this system.
Also tried:
Moved X-Fi from two slots down into the orange slot, was working immediately after bootup. I'm psyched beyond belief.
Will be buying the K9N Platinum. Thanks for the info.

Vista Beta 2 (v5472) + K9N SLI Platinum

Has anyone managed to get Vista installed from scratch with the "K9N SLI Platinum"?
I tried, 32bit and 64bit. both failed.

I got Vista Beta 2 32-bit installed on K9N Ultra + 4200+ X2, but because of the poweroff-issues of K9N-series, Vista was really unstable. Well, my mobo is RMA'd now, so let's see how's gonna work with the new revision.

K9N SLI Platinum & 5600+ W/Bios 1.2 Question?

Hello all,
I recently purchased an X2 5600+ and will be installing it on my board in a couple of days when I receive the CPU. I currently have BIOS 1.2 on my K9N SLI Platinum board and was wondering if any of you know if that particular BIOS will recognize the new CPU? (5600+)
Several new BIOS versions have been released and the latest is 1.6 but I am a person who goes by... "If it ain't broke, don't fix it"
Thanks in advance, and I look forward to hearing from you with insight.
The Ice!

Quote from: Piiooo on 26-April-07, 10:40:53
Just wanted to add my two cents.
BIOS 1.6 recognizes 6000+ as well, but it is a pain to update to 1.6 because a mobo with oroginal BIOS will not post
I did not have another CPU to flash BIOS, so what I did was just changing the multiplier in BIOS to 7 or 8, flashing the BIOS off a floppy drive and then changing multiplier back to 15.
Nice!
Thanks for providing a solution. I'm sure your discovery will help out a lot of people.
Cheers, the Ice!

MSI K9N2 SLI Platinum nForce 750a Problem

I bought this barebone kit a couple days ago http://www.tigerdirect.com/applications/SearchTools/item-details.asp?EdpNo=4692741&CatId=3508 and I had no troubles, I installed the 4GB Sli-READY 2GB RAM and thought that it wouldn't hurt to have another 4GB. So I bought the same RAM, and installed it, I started to get BSOD when I start programs, or games like "Lineage 2". I tried changing the voltage on DRAM but l can't change it to 1.8v, or 2.1v (2.1v says that the pc might be unstable) so l set it to auto. l also made it [AUTO] for SLI-READY DRAM. l still get BSOD.
Help would be greatly appreciated, the specs on the computer are:
MSI K9N2 SLI Platinum Motherboard
AMD Phenom X4 9850 Black Ed. 2.50GHz
OCZ SLI 4096MB PC6400 DDR2 / 8GB
Western Digital Caviar Green 500GB Hard Drive
Ultra LSP550 550-Watt Power Supply
(2) XFX nVidia 9800GT 512MB (1GB cause l have 2) SLI - Ready
Sound Blaster Audigy SE
My operating system is a Windows XP 64bit Edition.

Quote from: Younha on 04-July-09, 01:38:49
May you please explain how to use memtest and drop the mem. freq. to 667 and the 2T thing? :x
Memtest details ==> https://forum-en.msi.com/index.php?topic=103598.msg760534#msg760534
Quote
drop the mem. freq. to 667 and the 2T thing? :x
Apply "FSB/DRAM Ratio" in BIOS, 'Cell Menu' to 1:1.66
Quote
and the 2T thing? :x
By default it should be already 2T, verify that with CPU-Z memory tab{Command Rate} ==> http://www.cpuid.com/download/cpuz/cpuz_151_setup.exe

Msi p7n sli platinum ram chips problem

ok i have a msi p7n sli platinum mother board, i've had it now for the past 2 - 3 years. I finally got around to upgrading the ram from 2xcorsair xms2 ddr2 1024mb ram chips to 2x corsair dominator 2048mb ram chips.
i have checked the motherboard specs the voltage and MHz arent a problem.
But when i use 2 of the new chips my computer wont load the boot screen a 10th of the time. When i use 1 of the new chips it runs all the time. I was thinking it maybe a problem with the bios, i have reset it several times to the correct voltage, as it doesnt automatically some times.
anyone have and idea what i can do to fix this.

Please give full system specs --> >>Posting Guide<<
Try running the RAM at 800MHz 5-5-5-15 1.8V 2T.

K9N2 SLI Platinum Install,2 Problems, Resolved..

I upgraded to a K9N2 SLI Platinum With 9550 Quad Core.
I used a Copy of WinXp from a Thunderbird CPU System.
1. Boot failure at second test ( memory ) Green light flashing. I thought it was a memory failure.
Read install instructions," need spacers" on mounting screws ( ?, I thought board needed to be grounded to case).
Installed non conductive spacers ( top $ Bottom ). Fixed Boot problem....
Board Booted to system Install.
2. Next , repair WinXp with Install CD, (repair option after Install selected )
system Repair completed " Almost" bombed out at " lan,
Could not call MS on LAN, no LAN installed on repair process,
evidently MSI Lan not in MS Hardware table....
Installed PCI Lan, MS recognized LAN, talked to mother and completed repair of WINXP.
Cleaned up system with " CCleaner exe "
System working, Alls well, All old programs and Data retained....
SO< Suggest MSI provide a way to access lan on boot.... and ship Motherboard install screws/spacers...

You don't choose Repair actually. You let Windows find the previous installation. It will ask you there for a repair /rhyme!/. Here is a description:
Boot the computer using the XP CD. You may need to change the boot order in the system BIOS so the CD boots before the hard drive. Check your system documentation for steps to access the BIOS and change the boot order.
When you see the "Welcome To Setup" screen, you will see the options below
This portion of the Setup program prepares Microsoft
Windows XP to run on your computer:
To setup Windows XP now, press ENTER.
To repair a Windows XP installation using Recovery Console, press R.
To quit Setup without installing Windows XP, press F3.
Press Enter to start the Windows Setup. do not choose "To repair a Windows XP installation using the Recovery Console, press R", (you Do Not want to load Recovery Console). I repeat, do not choose "To repair a Windows XP installation using the Recovery Console, press R".
Accept the License Agreement and Windows will search for existing Windows installations.
Select the XP installation you want to repair from the list and press R to start the repair.
Setup will copy the necessary files to the hard drive and reboot. Do not press any key to boot from CD when the message appears. Setup will continue as if it were doing a clean install, but your applications and settings will remain intact.
You will not loose personal files, but you will loose Windows Update history.

K9N SLI Platinum operating system problems

Similar Messages

Maybe you are looking for