K9N2 Diamond - bios does not recognise Intel SSD 520 series

Hi,
I have a K9N2 Diamond motherboard and BIOS v2.7. I recently bought an Intel SSD 520 Series and when I connect it, the BIOS does not recognise the HDD at all. When I try to install Windows 7, the HDD is shown at the list, but it says that I can not install Windows at the HDD.
I have tried to connect the HDD at SATA port 5 and 6 and set the RAID mode to ACHI and also at ports 1 and 2 and set the RAID mode to IDE. Nothing works.
Any ideas?
Regards,
George

.and does the problem appears using the HDD which was equipped in this notebook?
If the BSOD would not appear using the HDD, then a problem is realalted to the inserted SSD drive.
In many cases firmware updates are released for SSD drives and in some cases this might be a solution.

Similar Messages

Bios does not recognise cr52-m drive

I recently updated the aspi drivers because I had a dvd rom which needed it, but it now seems that the cr52-m is now not reciognised by my bios.
This means Nero does not recognise the drive and on 2k pro the logical disc manager now takes several more minutes in loading.
I have searched the msi site looking for the firmware or driver for the drive but cannot find anything which can help me.
Live monitor does not give me anything useful to solve this problem.
So if support or any other forum member can point me in the right direction so I can resolve this issue so that my bios can recognise the drive again by flashing the right firmware, I will be happy to continue using msi products.

what is aspi driver?
Also, try to contact MSI by phone and e-mail about your problem as well not just this forum.

W510 type 4876-A11 With Intel SSD 520 Series BSOD

Hi lenovo community,
please help regarding this issue.
I took out the SSD from another computer which has never failed me.
I swap into thinkpad W510, and format and re-install windows 7 HomePremium . Keep getting Blue screen of death.
Tried win7 Professional, BSOD also.
Swap a hard disk into the w510, no issues.
Put the SSD into another computer, no issues.
W510 bios updated to latest.
SSD firmware update to latest 400i.
please help.
should i call thinkpad service hotline? It's still under on-site warranty.
seems like a compactibility issue.

Welcome to Lenovo Community! Terryhoho
Go to Control Panel > Lenovo - Airbag Protection > Uncheck Enable Active Protection System. (Check only when you are using HDD and not SSD) SSD does not require Active Protection System as it does not contain mechanical parts.
http://www.jdhodges.com/blog/tip-shock-protection-unnecessary-if-you-have-a-ssd/
If the step above does not resolve your issue.
1. What source do you use to reformat? Windows 7 Original DVD (Clean Install), Lenovo Recovery Disk or others?
2. If you install using Windows 7 Original DVD, download and install System Update. (If Recovery Disk, can skip this step as it's preinstalled in the image)
3. Download and install the latest Intel Chipset driver.
4. Go to Control Panel > Lenovo - Update and drivers > Install Critical and Recommended Updates, up to you for optional updates.
Peter
W520 (4284-A99)
Give kudos to reward people for their assistance | Mark the thread solved if the solution works | Direct e-mail regarding technical problems will be ignored
=====================================
Dolby ; IdeaPad Slate Tablet ; Equalizer APO

My 2010 imac does not recognise my time machine since I had the Seagate replacement hard drive. Any thought from anyone? The External hard drive is a 1 TB seagate

My iMac (2010 intel model) does not recognise or communicate with my external seagate drive as a time machine for back ups since I had the 1TB Seagate replacement hard drive as part of the replacement prgram with OSX LION 10.5.8 installed.
Is this because I need to update the time machine drive itself?

This excellent Support article may help you solve that TM problem:
http://pondini.org/TM/Troubleshooting.html

Itunes does not recognise CDs................please help

i've had my ipod for a few months now and it hasnt been a problem before as it has always imported CDs fine onto my ipod but recently whenever i insert a CD into the drive itunes does not recognise that i have put a CD in and it cant be the CDs that i put in as i have leant one of them to my friend and she said its worked fine on her itunes, when i insert the CD and go onto run CD diagnostics this comes up,
Microsoft Windows XP Home Edition Service Pack 2 (Build 2600)
FUJITSU SIEMENS P5SD1-FM2
iTunes 6.0.4.2
CD Driver 2.0.4.3
CD Driver DLL 2.0.3.2
UpperFilters: GEARAspiWDM (2.0.4.3),
Video Driver: NVIDIA GeForce 6200SE TurboCache(TM)\GeForce 6200SE TurboCache(TM)
IDE\DiskST3160023AS____________________________3.00___, Bus Type ATA, Bus Address [0,0]
IDE\CdRomHL-DT-STDVDRRW_GWA-4164B_______________1.03___, Bus Type ATA, Bus Address [0,0]
If you have multiple drives on the same IDE or SCSI bus, these drives may interfere with each other.
Some computers need an update to the ATA or IDE bus driver, or Intel chipset. If iTunes has problems recognizing CDs or hanging or crashing while importing or burning CDs, check the support site for the manufacturer of your computer or motherboard.
Current user is administrator.
D: HL-DT-ST DVDRRW GWA-4164B, Rev 1.03
Drive is empty.
The last failed audio CD burn had error code -128(0xffffff80). It happened on drive D: HL-DT-ST DVDRRW GWA-4164B on -128(0xffffff80) media at speed 0X.
i dont even understand what this means, please help!!!!!!!!!!!! thanx xxxx

Well the report just tells basics of your setup and errors going on in short. Error -128 means either you or iTUnes cancelled the burn before it even started.
Your issue tho is you have no lower filter. you should have 2, and upper filter and a lower filter. Now Im not that good with the filter thing just yet, but I think if you reinstall itunes it will install the lower filter you need.
You will want to remove itunes AND quicktime in the control panel>Add/remove. Dis able any antivirus/security programs so they do not interferr with iTUnes and then download and install the latest iTunes from www.apple.com

"This virtual machine is configured for 64-bit guest operating systems. However, 64-bit operation is not possible. This host does not support Intel VT-x"

Hi, I have installed vmware 5.5 hypervisor on hp G8 microserver. I have created one vm as windows 2008 R2. I have also install vmware workstation 11 on this vm. In this workstation when I tried to run vmware 5.5 hypervisor I come across "This virtual machine is configured for 64-bit guest operating systems. However, 64-bit operation is not possible. This host does not support Intel VT-x" this statement. Which shows that the host machine does not support virtualization and for that you need to go in Bios and enable it but in present case as host machine is also a vm and you would not find much detail of Bios when you log into the Bios therefore, I am pretty much stuck here. I don't see any information in relation to this. Now my question is:
1. Can we run ESXi inside a vm which is already sitting on ESXi?

I moved the discussion from VMware Workstation to Nested Virtualization which contains several hints on what's possible and what needs to be configured to make things work.
André

FCP X does not recognise my hard disc for storage

I run all my applications of a 120 GB SSD and replaced my DVD drive with a 1 TB hard disc for storage. This is working very well with all my applications apart from FCP. FCP simply does not recognise my hard disc as a place for storage, although it has no problem recognising it as a source to import from.
After doing some research on other forums, most commonly this problem is due to your hard disc having a typical "camera picture name" like "IMG_001" or "DCI_001" etc. for a folder at root level, thus FCP thinks the hard disc is a camera (for import) but not suitable for storage.
I have been messing around with this for days now, and would really appreciate some help.
Thanks in advance
p.s screen shots of typical infomation attached
- Duddleif is the name of the SSD
- Kjell is the name of the 'missing' hard disc

Instead of using older OS X CD/DVD install to a new drive.
Where is your backup and clone?
Buy some drives! that is a must.
Pick up a FW case, you will need it to put the old drive in, and later, so you have an external and off line drive for backups and maintenance.
A copy of TechTool Pro 4/5 and Disk Warrior (DW first).
SuperDuper to clone your drives.
Demo of Prosoft Data Rescue 3 to scan the drive once you have a system and you put the 'dead' drive in FW case.
Then do backups and preventative maintenance on a very regular basis and have at least two backup sets.
If you have been doing that, and know and have read those instructions in the past....

Satellite P100-434 does not have Intel Vitualisation (VT)

Hi,
My shiney new P100-434 which cost me a fairly serious amount of money does not have Intel Vitualisation (VT) enabled which is annoying because I went for this laptop specifically because it was Core 2 Duo which supports VT and I want it in order to run KQEMU faster under Linux.
There is no option to switch it on in the BIOS and no updated BIOS available either.
Anyone know if a BIOS with the option to enable this feature is coming or suggestions for who I should complain at to make this happen faster? I see plenty of other people in the forums with other models that similarly have it disabled by default and no BIOS option to turn it on!
Cheers,
Jamie

Hi
I have already posted my statement to this theme.
Please check this thread:
http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=21855

K9N2 Diamond Bios

Has anyone noticed that on bootup the K9N2 Diamond BIOS (both available versions) read AMD Northbridge? What does that mean, I wonder...

The integrated memory controller in the CPU.

IPod Nano: Error Message "The USB device has malfunctioned and Windows does not recognise it"

Hi everyone, I just received 2 brand new iPod Nanos for my kids for Christmas, thought I'd be smart and sync them both now before wrapping them so I don't have to be messing around with them on the day. One synced without a problem, then using the same cable, same computer, same USB port, the 2nd one came up with "The USB device has malfunctioned and Windows does not recognise it" I've tried restarting my computer, unplugging and reinserting the USB. Is there anthing else I can try before returning it? Thanking you for any help.

I have solved my problem, I ended up ringing Apple and got an awesome lady who told me to reset it by pressing the sleep button and menu button together for about 10 seconds and once it actually turned on for the first time the computer then recognised it, so it's all good, :-) Thank you lovely lady!

I have a 16GB iPhone 3GS. Tried synching my phone through iTunes (11.0.1 I think... on a 2009 Macbook Pro). Now when I connect to iTunes, it says it does not recognise the content on my phone. Is this because my phone (and laptop) are too old?

I have a 16GB iPhone 3GS. Tried synching my phone through iTunes (11.0.1 I think... on a 2009 Macbook Pro). Now when I connect to iTunes, it says it does not recognise the content on my phone. Is this because my phone (and laptop) are too old?
Also, when I tried to Restore the settings, an Error Message pops up that says " The iPhone software update server could not be contacted. The requested resource was not found.
I'm trying to free up space on my phone by removing [literally] thousands of old photos which were originally synched to the phone, because I had forgotten to uncheck the photos button when I synched it ages ago.
I have also tried synching it on my 24" iMac (running OSX Snow Leopard). But again, when I try restoring the phone through itunes, it says the file is corrupted. It sggests unplugging the device, and then plugging it in again. I have done this numerous times with no success.
I'm guessing it must be because my phone (and versions of iTunes, and OSX) are all too old.
Please can anybody help.
Cheers,
Dan_nz.

There are multiple reasons that lead to issue. You should read the troubleshooting guide to get the right solution to solve the issue: iPhone, iPad, or iPod touch not recognized in iTunes for Windows - Apple Support

I changed from i iphone 5 back to a iphone 4.. now my itunes does not recognise that i have a iphone 4! how do i convert my last back up (on iphone 5) to my new iphone 4?

i changed from i iphone 5 back to a iphone 4.. now my itunes does not recognise that i have a iphone 4! how do i convert my last back up (on iphone 5) to my new iphone 4?

In your case you can only restore from a backup that has been created with the same iOS version. An iPhone 4 can only run 7.1.2, and, unless your iPhone 5 did not run the same version, you can't use a newer iOS backup of the 5 on the iPhone 4

HT1414 I was in the middle of updating my iphone 4s to iOS7, then it crashed, I am able to get the apple simple when trying to restart, then it shows the cord and itunes logo and then switches off again. Itunes on computer does not recognise the phone

I was in the middle of updated iOS7 onto my 4s then it crashed, tried to restore and backup and it wont power off restart it just shows a black screen.
Tried the tips
Does not recognise my phone as I updated Itunes to see if this would work and I have lost all my back ups and every thing,
when i try the power on butter and the home button I get the apple icon, then it shows power cord and itunes logo and then returns to a black screen, I can hear it beeping like when you put it on the charge each time this happens on my PC.
please can anyone else help me???

Unable to Update or Restore..?
See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once...
Take your time... Pay particular attention to Steps 3 and 4
Note:
Some users have reported as many as 8 or 9 attempts were necessary before success.

My Apple TV does not recognise My iTunes password. It works on all other devices but not Apple TV? Any ideas why or how to fix?

Any ideas why my Apple TV does not recognise my iTunes password, when all other devices, including these communities are good with it?

Hi Mick2291,
Thanks for visiting Apple Support Communities.
I'd suggest restarting, and then restoring, your Apple TV if the issue persists:
Apple TV (2nd and 3rd generation): How to restart your Apple TV
http://support.apple.com/kb/HT3180
Apple TV (2nd and 3rd generation): Restoring your Apple TV
http://support.apple.com/kb/HT4367
Best Regards,
Jeremy

Please help. ive bought a second hand ipod nano, when i connect it to my pc it recognises it as a sigma mass usb device, yet its a 8gb ipod nano,and i tunes does not recognise it, im running on windows vista basic yet my own 80g classic ipod runs perfect

please help. ive bought a second hand ipod nano, when i connect it to my pc, it does not recognise it in itunes,yet it comes up as a sigma mass usb device. its an ipod nano 8gb?. im running on windows vista,my own ipod classic runs fine.

there is a good chance that this can be related to bad contact in USB lead.. e.g not enough power from IPOD to PC so that pc cannot recognise it. Where I work I get alot of USB devices on pc's that are not recognised and most of the time it is the connection to the device that is not good enough because the flat end of the USB adapter has been gradually bent over time just slightly and now contact is not good. It can also be todo with drivers or If you are using it through a USB hub.
so if it is not working through USB hub try direct. also try in back of PC as these Ports or direct access to main board to pc and would be less trouble some if there was a voltage loss from mainboard in pc to front of unit.

K9N2 Diamond - bios does not recognise Intel SSD 520 series

Similar Messages

Maybe you are looking for