K9N2 Diamond - not working with 4x 1Gb Corsair PC2-6400 modules

Hi !
I've just discovered that my K9N2 Diamond will not accept my 4x 1Gb Corsair PC2-6400 modules with my new GTX275, although they seemed ok with my temporary 7950GT card.
The only noticeable difference is that one pair is 5-5-5-18 (installed now alone and working) and the other pair is 5-5-5-12 (removed).
Is this normal ? I also noticed that the actual installed pair is working in "Unganged 128Bit mode" compared to the previous "Unganged 64bit mode".
Would it therefore be wise for me to purchase 2x 2Gb modules instead ? I read that the Athlon x2 6000+ processor only works with DDR2 800Mhz memory ... Is this correct ?
Thanks in advance for your help !

Quote from: GEC on 28-May-10, 01:40:03
Hi,
Just a quick update : I set the DRAM frequency to 667Mhz using the FSB/DRAM ratio = 1:1.6 but to no avail : the system hangs at post. Would it be better for me then to buy 2x 2gGb sticks ?
Quote
Just a quick update : I set the DRAM frequency to 667Mhz using the FSB/DRAM ratio = 1:1.6 but to no avail : the system hangs at post.
Also make sure that 2T is used
Quote
Would it be better for me then to buy 2x 2gGb sticks ?
Yes, that's best option. For best performance and troubles free use 2x matched memory sticks only.

Similar Messages

K9n2 Diamond having trouble with more than one stick of ram

Hi there. Thanks for reading. My setup is as follows
WIN-500xspx 500W PSU
Geforce 9600 GSO
7750 BE Kuma
XP 64bit
k9n2 diamond w/ BIOS 2.3
2GB Mushkin HP2-6400 (2x1GB)
I just got the board two days ago and got everything set up, but I've been having some trouble with my ram. Whenever I have more than one stick of ram, it fails to post, unless I clear the cmos before I power on. Then, it will give me the option to load the bios or run on default settings. If I run on default, it will boot up fine and work well for about 5 minutes. Then it will shut off and not post until I've cleared the cmos again. So, I figured I had an incompatibility issue with the ram. So I tried another set, the Crucial Ballistix BL1286AA1065.8FEF with the same results. Next I went with the Rendition RM12864AA800 with the same results. I tested each stick individually and they're all good. Each slot works fine as well. I switched the old mobo back and all was well. The only thing left is the PSU but I don't think thats the problem. Any suggestions would be greatly appreciated.

Quote
. If I run on default, it will boot up fine and work well for about 5 minutes. Then it will shut off and not post until I've cleared the cmos again.
Its the PSU, go for better one with strong single rail like Corsair VX,TX Series.

Do SD card readers not work with 10.3?

I have an old G4 Power mac, and my kids have iMac G5s. We all run 10.3.9, and have SD card readers, and none of them work at all. Does Apple acknowledge that SD cards do not work with Macs, and/or was this fixed in 10.4? We are looking to replace our computers, and this is a deal breaker.

Okay, I did a little more research, and here's what I have found.
(Yes, I'm talking about a USB card reader.)
On my ancient G4 Mac, the 2GB card never mounts. I can see it with Disk Utility, but Disk Utility usually offers to format it. When I do this, it attempts to format it as a 1GB card, and fails.
However, I found an old 16MB card, and it mounts every time.
My kids both have a reader and a 2GB card for their iMacs. They usually mount okay, but not always. Sometimes it takes a restart.
The 2GB cards are all a funky off-brand, "Adata." The 16MB card is a Canon.
Now I am wondering if it's the cheap cards, or the capacity of the cards. I remember reading at one time that some Macs don't want to see removable drives over 1GB. This may be the problem with my computer. I just ordered a 1GB PQI card, we'll see how that does when it arrives.
My mac has both USB 1.1 and 2.0 slots. Same results on either bus.

ACROBAT XI - DOES NOT WORK WITH WINDOWS VISTA

WHY DOESN'T THE COMPANY STATE ACROBAT XI PRO DOES NOT WORK WITH WINDOWS VISTA.
THE COMPANY NEEDS TO WARN PEOPLE. THE ACROBAT TECH SUPPORT FINALLY FIGURED OUT THAT IT'S NOT COMPATIBLE WITH WINDOWS VISTA.

The Acrobat website and the box lists the compatible OSs. You want Adobe to list all of the incompatible OSs---going back how far.
Acrobat XI Pro system requirements
These system requirements are for Adobe® Acrobat® XI Pro software, v11.0. Because system requirements change with each software update, refer to the Release Notes for your software version for the latest information on supported operating systems and browsers.
Windows
1.3GHz or faster processor
Microsoft® Windows® XP with Service Pack 3 for 32 bit or Service Pack 2 for 64 bit; Windows Server® 2003 R2 (32 bit and 64 bit); Windows Server 2008 or 2008 R2 (32 bit and 64 bit); Windows 7 (32 bit and 64 bit); or Windows 8 (32 bit and 64 bit)
512MB of RAM (1GB recommended)
1.85GB of available hard-disk space
1024x768 screen resolution
DVD-ROM drive
Internet Explorer 7, 8, 9, or 10; Firefox Extended Support Release; or Chrome
Video hardware acceleration (optional)
Note: For 64-bit versions of Windows Server 2003 R2 and Windows XP (with Service Pack 2), Microsoft Update KB930627 is required.

H.264 not working with QT

H.264 streaming does not work with QuickTime instead a green screen pops up. I can watch the camera (Axis P1343 network cam) using Motion JPEG stream profile but not H.264. The camera LiveView is set up to use QT but QT does not respond. I know this issue has been discussed before and a lot of literature exists on this subject on line. Has a solution been found? My computer is a MacBook Pro running Snow Leopard 10.6.8.
Any advise will be greatly appreciated.

Thanks for the quick response, I checked with our Admin guys
and it indeed 3.0.0.
So I will update immediately.
Is there a big advantage to using H.264 over VP6 for live
streaming?
I have another forum question that went unanswered relating
to this issue asking, what are the required recommended settings
for both FMS 3 and FME 2.5 to reduce any lagging in video on a 1gb
LAN which should not have any?
cheers again

Can't get k8n diamond plus working with 4x1Gb

I managed to get the DDR memory frequency running at 333MHz using only 2x1Gb in the Green slots of the motherboard (as listed in page 2-7 of the K8N Diamond Plus Manual).
However, when I add the other 2x1Gb modules to the Purple slots, the system does not even come up.
I've then went back to 2x1Gb in the Green slots so that I can get the system to fire up, gone into the BIOS and adjusted the settings according to the configurations below and restarted.
I've then shut-down and re-inserted the other 2x1Gb into the Purple slots so that 4Gb is present, then rebooted but the system still does not come up.
Adjust CPU FSB Frequency: 200.0
Current DDR Memory Frequency (this is Read Only) DDR 333
Adjust DDR Memory Frequency: set to Manual
Memory Clock: Tried all of the following for DRAM/FSB 1/2,2/3,5/6,1/1,5/4
Does anyone know of any person who has got a K8N Diamond Plus working with 4x1Gb ?

Tried removing one of the video cards and disabling the sound card (as suggested by http://www.asktheramguy.com/v3/showthread.php?t=65436), but the system still didn't fire up with 4Gb RAM.
Hans,
I managed to find the D-Bracket and here's the sequence that the LEDs cycle through:
LED1
LED2
LED3
LED4
DESCRIPTION
1
red
red
red
red
System Power ON
2
red
red
red
green
Initializing Video Interface
3
red
red
green
green
Initializing Hard Drive Controller
4
red
red
red
red
System Power ON
5
red
red
red
green
Initializing Video Interface
6
red
red
green
green
Initializing Hard Drive Controller
7
green
red
red
green
BIOS Sign On
8
green
green
red
green
Assign Resources to all ISA
Row 7 of the table above indicates "BIOS Sign On" and this should start showing information about logo, processor brand name etc, but this does not occur.
The cycle (phases 1 to 8) then repeats incessantly.

I have recently upgraded my iMac Intel G5 iSight to OS 10.6.8 and now the internal mic does not work with skype or facebook. I can here static when playing back clips. Do I need to update firmware or reload old sys parts

I have recently upgraded my iMac Intel G5 iSight (iMac5,1) to OS 10.6.8 and now the internal mic does not work with skype or facebook. I can here static when playing back clips. Do I need to update firmware or reload old system parts. I have zapped PRAM. The blue indicator in system audio panel will appear for a second as I slide the bar for internal mic but then it disappears. Is there a fix?

The sound seems very faint but can here static on playback.

My operating system windows XP not working with photoshop cloud, why not?

I need to add 2 more licences for photoshop cloud and I'm being told my operating system windows XP does not work with Photoshop cloud. We already have 2 pcs using it in our office so why not?
Please help
Roy

Do you have the latest version of iTunes? If not, get it at:
http://www.apple.com/itunes

Adobe creative cloud eea 1.5 is not working with our asus Eee box , celeron j1900 2.00 ghz, 4gb of ram, 64bit. can settings be changed in adobe?

adobe creative cloud eea 1.5 is not working with our asus Eee box , celeron j1900 2.00 ghz, 4gb of ram, 64bit. can settings be changed in adobe?

A chat session where an agent may remotely look inside your computer may help
Creative Cloud chat support (all Creative Cloud customer service issues)
http://helpx.adobe.com/x-productkb/global/service-ccm.html

Application is not working with mouse

Dear All,
We have a strange issue in the our application (Oracle form) in the one of our client machine.
Some times the forms are not able to work with the mouse but is able to work with the keyboard. After one or two machine restart its again working. When the issue occur we can able to work in other applications using mouse.
Our Applications server is in Other country and client are accessing from India.
This occurs for some user and not for all.
Application server Version 10.1.2.0.2.
Oracle Database 11g Enterprise Edition Release 11.2.0.1.0 - 64bit
Java Plug-in version 1.6.0_31 .
Please any info will help us lot.

Thank you for the quick replies Michael Ferrante and HamidHelal.
But since its occurring for some users (perticulary indian users) and some times. And also its occurring in production environment not in development environment.
Even the java control panel is not working with mouse.
For other country customers everything working fine.
So its difficult for me to apply the patch with these uncertainties.
Checking with fresh java installation and let you know the status.
Thanks.

Voice Memo is not working with iOS 8.2

Voice Memo Records is not working with iOS 8.2. how to fix it?

Voice Memo Records is not working with iOS 8.2. how to fix it?

On updating my iphone it shows no network inspite the sim inserted,now it also not working with itunes.i cant see menu page on display screen

on updating my iphone it shows no network inspite the sim inserted,now it also not working with itunes.
i cant see menu page on display screen

http://support.apple.com/kb/HT1808

Caller ID not working with Nokia 6600?

I have a T-Mobile (US) Nokia 6600, and I can't seem to get address book to display incoming SMS or the caller ID of incoming calls. I've successfully paired the phone via bluetooth, and I can make address book dial the phone and send an sms. I can sync via iSync, use my phone as a modem, etc. etc.
But regardless of what settings I tweak, I can't seem to get Address Book to show a bezel of any kind on incoming calls - not even an 'Unknown Caller' message! Am I missing something obvious? Third party apps like BluePhoneElite work just fine, so I'm pretty sure it's something wrong with Address Book...
15" Aluminum Powerbook 1.5 GHz Mac OS X (10.4.5)

mdcdsc wrote:
My caller ID does not work with the new ap either. I don't like the new ap at all. The old one was beautiful. Now my email is very hard to see, so much that I will just use the Apple email that comes with my IPOD. The caller ID was my favorite thing with the old ap. and now it doesn't work. I have followed the instructions and turned everything on, but it just does not work.
The Caller ID issue was due to an outage. It should be resolved anytime soon. Can yu log out and log back in. Go to app settings and in notifications and turn CAller ID off and on.
On email - what do you mean 'email is very hard to see' ? I would like to pass on this feedback to the team.

Flash player does not work with new ICS Android 4.0.4 OS. Has this problem been addressed?

Flash player does not work with new ICS Android 4.0.4 OS. Has this problem been addressed? I am using Firefox Beta for android and I also tried just Firefox.

Please check the Play Store app for any Flash updates and install them if present.

Flash player does not work with Ie or Firefox with win 8.1?

Flash player does not work with Ie or Firefox with win 8.1 64, If i try and play a video I get the message to install Flashplayer.
If I try and install it it says it is already installed. Your onsite installer says it is not applicable to my machine.
I have followed all the normal steps re enabling addons and active filters etc.
all to no avail Pc is Dell 6 months old, Flashplayer has never worked on this machine. Last MS update mid Dec 2014.
Version of flashplayer is 15....03.......

Flash Player is a built-in component of Internet Explorer. There's nothing separate to download or install.
Firefox requires a different version of Flash Player (the NPAPI plug-in), which will be served to you if you go here: http://get.adobe.com/flashplayer using Firefox; however, there are some unique stability issues related to Firefox on Win8.1, and you're probably better off using Google Chrome if you want a more optimal experience with Flash Player.
For problems where IE isn't being detected by sites that require Flash:
First, confirm that ActiveX Filtering is configured to allow Flash content:
https://forums.adobe.com/thread/867968
Internet Explorer 11 introduces a number of changes both to how the browser identifies itself to remote web servers, and to how it processes JavaScript intended to target behaviors specific to Internet Explorer. Unfortunately, this means that content on some sites will be broken until the content provider changes their site to conform to the new development approach required by modern versions of IE.
You can try to work around these issues by using Compatibility View:
http://windows.microsoft.com/en-us/internet-explorer/use-compatibility-view#ie=ie-11

K9N2 Diamond - not working with 4x 1Gb Corsair PC2-6400 modules

Similar Messages

Maybe you are looking for