K9N2 SLI Platinum and Phenom II 940

I have a K9N2 SLI Platinum and have a Phenom 940 on the way. Are there still issues with bios 3.4? what is the proper way to flash to 3.4 so the volatge is normal ? I just flashed via the usb meathod but dont i have to reset and clear cmos? also what is the stock proper voltage for the phenom 940? is it 1.375 or 1.350?
K9N2 SLI
Phenom 9750
8GB OZC SLI 6400
XFX 9800GT SLI
OCZ 550W

Quote from: digitabc123 on 08-April-09, 06:59:12
have you tried uping the voltage, the black dragon works perfect at 1066 from 2.2v to 2.4v, however the gskill requires 2.3v to work perfect at 1066 (so my setup its 2x1gb geil and 2x1gb gskill (total 4gb) voltage set to 2.3v) if i dont set 2.3v i get completely random restarts (could be after afew hours or afew days), all passed with prime and occt.
just in case, after bios reset ddr is set to 800 as default ,go into bios and set divider to 1066, then set timings to 5-5-5-15 (dont use auto/sli ready) bios sets strange timings by default at 1066 then set voltage and save.
I've tried everything and even chatted with MSI Techs over it all, been back and forth between MSI and OCZ for about a month now.. bottom line, MSI told me was that they don't certify or support OCZ ddr1066 on the K9N2 SLI Plat; which OCZ Techs told me, basically. B.S! ...claiming they tested the Board themselves when it came out. However OCZ doesn't even have the Board listed on their RAM Configurator on their website; which they claim is MSI's fault... and so on, and so on...
Anyway, OCZ is offering to swap my Reaper Set for a different Model set which they claim is more reliable on AMD processors. Probably their Gold or SLI model set I'd guess; they don't even advertise on their website any difference in their sticks being "Intel Certified" or "AMD Certified" ... and so on.
Worse case scenario; if in the end whatever they give me still doesn't work, I'll EBAY it and try a set of those geIL Black Dragons.

Similar Messages

K9N2 SLI Platinum - new Phenom support and OC

____________E D I T ___________________
MSI K9N2 SLI PLATINUM
SUPPORTS
AMD PHENOM X2 965 BE CPU
____________E D I T ___________________
if it didn't I would be crying in a corner somewhere not posting this from my super fast PC
Thanks to all you guys
____________E D I T ___________________
Hi guys,
Had my lovely new M/B for a few months now and It has been a wonderful board.
despite one hiccup where the PCIE bus had a moment / died ( flashing the BIOS to latest fixed it )
My setup currently :
Jeantech Storm 700w Modular PSU
MSI K9N2 SLI Platinum
AMD Phenom 9550
with Zalman silent fan
4GB crap ass RAM (that's a real brand .. honest)
2 x BFG 9800GTX+OC in SLI I likes these .. they make lovely noises in my dark room .. VrrrrUmmmmmmm mmm mmmm mmm
500 GB slow ass HDD (Again the marketing dept of this brand were out to lunch when they launched it)
Windows 7 RC. latest build
Nvidia Det's 190.xxx latest driver
mostly playing Fallout 3 (graphics are beautiful but notice the CPU is lagging behind now)
So to the Crux of my issues :-
I'm looking to upgrade a few things here though,
as you can see a few components are severely bottlenecking performance.
First off the RAM.
going to get some nice Kingston 1066 DDR2 (4GB or should I go for 8GB ?)
next .. a WD VelociRaptor 10k rpm HDD probably just a small 74GB or the 150GB drive
and finally the pies de resistance ( yes PIES ! .. I like PIES !!) shiny new AMD Phenom 965 CPU
SO... Will the 965 phenom work in this board ? I've logged on tech support but no answer,
latest BIOS is installed already 7374v35 i think.
I know it's a 140W CPU so okay there,
the Socket AM2+/AM3 is good
.. I just NEED to be sure before spending £200.00
if not .. is it worth getting the 945 or 955 BE and clocking them ... could the board handle clocking the 965 ??
and last of all, if any one has any opinions on the build .. let me know... have you built a similar rig ?
cheers all
PIES out ~!
OCD

WoW !!
Thanks for the replies guys, I really appreciate it...
and after a drunken bout of spontaneous cash wastage on the internet last night :
1) AMDOA06KNF PHENOM II X4 965 £151.07
2) WDGA060T2 WD VELOCI RAPT 150GB £99.07
3) KTEA069M4 4GB 1066MHZ DDR2 £41.70
... goods on the way...
So I guess in a few days I'll be able to update you all on the build and will more than likely be updating this post with my random moronic questions and queries when the next thing goes wrong
looking into Power requirements
9800GTX+ SLI requires a min 550w PSU .. and so far in top gaming and 3D benchs hasn't gone over 250w on the meter ( pretty good I think)
the Zalman CNPS9700 LED seems to keep everything cool without any power to the fan... but I leave power on low just for the pretty blue lights
I'm happy to listen to any advice though,
One thing I will need is any pointers you can give on the K9N2 built in OC facility in the BIOS .. is it any good .. can I TRUST it to not fry my CPU by running it on auto ? is there any recommended settings ? etc. your thoughts and experiences welcomed
OCD

K9N2 SLI Platinum w/ Phenom II 940BE - Overclocking Advice?

So I am wondering if any other USERS out there, can give any advice on how they've managed to overclock their Phenom II 940 "BE"s on an MSI K9N2 SLI Platinum motherboard?
Now that I got my board running rock solid and stable, I am interested in venturing in this territory and I am curious as to what sort of "stable overclocks" others have achieved and how you configured to achieve such?

Quote from: TheCello on 02-April-09, 01:55:00
I have mine @ 3.4GHz on stock vCore w/ bios 3.3 (vCore is at 1.375ish) with the multiplier settings and the FSB at 200.
Which sucks, because I don't want the extra voltage. I need my proc to stay under 50C and playing crysis, it reaches exaclty 50C.
This is only a minimal increase in perfrormance tho. What I really want, is to be able to overclock the HT link. unfortunately, if I set it to 2000mhz, I get instant freeze at boot, if it even posts at all. Trying to install BIOS 3.4 today. lets see how it works =)
How are you getting it 2000mhz HT? Raising the HT multiplier will not render a bootup. Incrementally raising HT will get you there....with CPU multiplier raised, a little bit of HT will give better Numbers on the CPU - Say 17 x 215 as opposed to stock 17 x 200. My brother has that board, 215+HT no problem, he has a thermaltake active Heatpipe Northbridge cooler attached to the stock cooling.

¿Could work together a MSI K9N2 Sli Platinum and a Radeon HD 4890-HD489XZSFC?

Hello. I know that nVidia and Ati chips are not the best friends. However, I have a very good price and opportunity to buy the XFX RadeonHD 4890 1 GB DDR5 HD489XZSFC. Should I try? Actually I`m running a MSI 9600GT-OC which is not bad at all. This 4890 seems to be really great, I`ve been reading a lot of customer reviews and all of them were delighted.
K9N2 use the DDR2 memory and this GPU has the DDR5.
What do you think about?
Regards,
Florin

We are not going to recommend other manufacturers competing products. ATI video cards and NVIDIA MOBOS should have no problem working together. So, an MSI Radeon 4890 should not have any issue with a K8N2 SLI Platinum.

K9N2 SLI platinum - another problem w/ Phenom II

I decided to upgrade my K9N2 SLI Platinum from Phenom 9850BE to Phenom II 940 3.0GHz. I switched the CPUs but I didn't update the bios from 3.2 to 3.3. When I powered up the bios 3.2 system with the Phenom II it posted and booted but then blue screened. I restarted and went into the bios settings and checked the hardware monitor and it showed the CPU temperature at 80C! I looked at the voltage and this bios was giving the Phenom II 1.8 volts. I immediately shut down and felt the CPU sink and it was quite warm after only 60 seconds or so. That wasn't a stock heatsink either - it was a CNPS9700 with AS5 - a lot of copper to heat up.
It seems that the 3.2 bios, if it didn't recognize the CPU, should not have set the VCORE to the maximum of 1.8 volts and continue to run.
Also, I replaced the Phenom II with a sempron to upgrade the bios and had a problem after successfully flashing 3.3. I spent the weekend back and forth with MSI support and they sent a beta bios 3.3.3 that did work. My problem with 3.3 was that the machine would freeze before POST with the Group 2 LED flashing green/red.
I'm waiting for a new CPU and wondering if I should also RMA the motherboard. How come so many people seem to have flashed 3.3 with no problem but mine didn't work?
# CPU: worked: 9850BE with 4 2Gb sticks of CORSAIR DOMINATOR 1066 (worked at 1066 all four)
burned up by bios version 3.2 Phenom II 940
used to flash bios: Sempron 1800
# Motherboard model: K9N2 SLI Platnium
# Video card: MSI 8800GTS
# Hard drive(s) Seagate SATA 80Gb
# No other cards.
# Operating system: win32 XP
# Power Supply: New ANTEC Neoblue 650W.
Will

Quote from: hifi239 on 04-February-09, 00:37:10
Thanks for all the information. As I said, I have the MB working on a spare Sempron and I am waiting for a new 940, but here are some facts I'm still curious about:
1. With a plain vanilla Sempron 3400+ and a plain vanilla one stick of slow memory my K9N2 SLI Platinum will not boot correctly with bios 3.3, even after resetting cmos, unplugging, etc. MSI tech had to send me 3.3B3. Anyone know why that would be. Is there something wrong or different about my MB compared with everyone else that has 3.3? What bug in 3.3 is fixed with 3.3B3?
The sempron should boot correctly. (3.3Beta3 is a pre-3.30)
Quote
2. I'm sorry but I think that with 3.2 or 3.3 or 3.3B3, before flashing, after flashing, with cmos reset, with cmos not reset, the bios should never put the red maximum 1.8 volts on a CPU it doesn't recognize. I never set that parameter. It is a bios bug for it to switch up to 1.8 Vcore. I had the 9850BE at Auto (about 1.1V I think).
You need 3.30 and after reset the cmos.
Quote
3. "I doubt it burned the CPU" Really? The max case temp for 940 is 60C. Mine got to 80C. That's not good, even if it does still work. Fortunately I purchased from NE who will RMA it.
I doubt yours even got 80C as you where using the wrong BIOS...did you measure it with a digital temp-meter?
Did you burn your fingers on the heatsink?
It's not the first time a CPU temp is being read wrong in the BIOS.
Quote
4. digit123abc said "i have the same board and 940BE, 3.3 sets the cpu voltage to 1.8volts even after bios reset and loading defaults" So, when I get the new 940, with 3.3B3 am I really going to have to rush into the bios and change the 1.8Volts to auto before I burn that CPU also? If so, that's a bad bios bug.
A BIOS default is Vcore at Auto, never seen anything else....not a BIOS-bug but he didn't reset the cmos after flashing.
And again 3.3Beta3 is older then 3.30 that is release version.
Same as with Windows7 Beta....thats prior to Windows7 Release.

K9N2 SLI Platinum - JPW2 connection essential? Also, question about diagLEDs

I've been running a K9N2 SLI Platinum with a Phenom 9950BE and 2 Geforce 9800GT video cards for half a year now, running as stable as any computer could and I couldn't be happier. However, there's one thing that I've always had a question about - the molex connection on the board labeled JPW2. The manual says that JPW2 is "used to provide power to stable the operation of graphics card", but using the PCI-E connectors on the card appears to be adqeuate to running a stable system.
In regards to this though, am I running the risk of an underpowering my motherboard not having JPW2 plugged in? The 24-pin and 8-pin power connectors on the board are of course plugged in and my concern is merely (hopefully!) academic at this point, but I'm just curious if not having power running through JPW2 would cause any problems down the line. My components are power hogs and I believe my power supply is up to it, but I'd love it if someone wiser than I could indulge my curiousity.
Also, my diagnostic LEDS are reading something other than four green solid lights in normal operation (successful POST, Windows loaded and running). If you were to view the motherboard correctly mounted in the case, the order of the lights are: [G][R][R][G]. The manual refers to this as "BIOS Sign On - This will start showing information about logo, processor brand name, etc..." which is as incredibly unhelpful as it can be when it comes to this sort of thing. I state again that this doesn't effect normal operation - it's just another thing that I'm curious about.
Thank you for helping me put my mind to rest!
SPECS
K9N2 SLI Platinum
AMD Phenom 9950BE
8GB G.Skill 800MHz DDR2 RAM
2x Geforce 9800GT 1GB
Seagate Barracuda ST3320620AS 320GB HDD
SAMSUNG Spinpoint F1 HD103UJ 1TB HDD
LITE-ON DH-20A4P-04 20x DVD-DL Writer
Thermaltake W0116RU 750W ATX Power Supply
CM Storm Sniper ATX Case
Windows Vista Ultimate 64-bit

Quote
1. Will not plugging in JPW2 will adversely affect system performance stability.
No, but its recommended to be connected.
Quote
2. Diagnostic led is shoring GRRG during normal use. No apparent adverse effects. Manual quite unhelpful. Cause?
If the system works OK ignore it. Else ask here: http://ocss.msi.com/

K9N2 SLI Platinum Freeze

I did a build 3 weeks ago and everything was smooth as silk. Then this morning was reading up on the news online and system shut down. Try to turn power back on and all leds light green to say OS loading but nothing happens. No post, no bios, no feed out any of the video. Have tried swapping out memory, video cards, using on-board video, clearing cmos, pulling battery and let it sit for an hour. Nothing I do makes any change. I press the power button, the d-led lights green instantly, green #15 for power and the orange for standby, both for the pci-e cards. Please let some one have an idea other than replacing my cpu.
K9N2 SLI Platinum
AMD Phenom X4 9850
4gigs 1066mhz Kingston HyperX
2 - NVidia 9500gt's in SLI
Vista Ultimate64
Acer 22" LCD

Man oh man, I found the issue alright. After trying everything under the sun including all your suggestions, I finally pulled the ruby orb cpu fan off. Scorch marks on the CPU. With low running temps, I'm not sure how it could be other than just a bad cpu. Tigerdirect(whom I purchased it through) said they refuse to exchange it even though I'm under 30 days, but luckily after contacting their supplier (no help from tiger) they are going to swap it for me. Only fear is, could some fault have happened on the motherboard to cause this? Or could the psu have spiked? But if the psu spiked, wouldn't the motherboard be completely dead instead of just unresponsive? Also, one chip on the board above the am2 plug-in and toward the rear looks a little different. Not cooked so much as just not as shiny as the others near it. Could there be a problem there? Don't want to be sticking in a new cpu just to have it fry cause of the motherboard being faulty. Thanks for your ideas.

New K9N2 SLI Platinum isn't booting into BIOS

So i just built a new system with an MSI K9N2 SLI Platinum, and installation went by with a breeze. However, after supplying power, and turning the system on for the first time I'm met with absolutely nothing.
I'm not the most advanced in this category, and I've certainly never experienced the likes of this ever. I've gone through the hardware configuration a thousand times, and I'd know if it were that.
I was wondering if anybody knew a few tricks to get this new board to boot. I'm suspecting it's probably something small and obvious I wouldn't ever think of.
But yeah, any help would be much appreciated.
Current System:
Mobo: MSI K9N2 SLI Platinum
CPU: AMD Phenom X4 9850 (black edition)/stock cooler
RAM: Corsair Dominator 2x2048Mb 1066Mhz DDR2
GPU: PNY XLR8 GeForce 9800 GTX
HDD1: Western Digital VelociRaptor 300GB 10K RPM
HDD2: Seagate Barracude 1.5TB 7200RPM
No operating systems yet (which is kind of impossible since I can't even set the boot order without the BIOS loading.) But I plan to run XP Pro alongside Gentoo.

All fans are spinning fine, I'll get the PSU info later, I took it from an old system I built before my last deployment. It's an 850 watt (single 12 volt rail) system, not sure the exact specs on it anymore.
I do believe though, that I've managed to knock something loose as it keeps beeping repeatedly now when it boots. Before it was absolute silence on boot. (which is weird because i don't actually remember installing the speaker?)
Oh, the DVD drive is from another system too, and pretty old, but it opens, and functions.
I also swapped between onboard video, and the graphics card to see if it was maybe the graphics card and still nothing.
Though I have to use a DVI converter with the graphics card (which is pretty lame for a 200+ dollar graphics card to have two DVI ports and an SVID port, but no HDMI port.)
Anyway, I originally tried to boot with my 1080P television connected into the HDMI DVI* port for the mobo.
Keep good language in a forum!
Now if I can just figure out what was wrong in the first place eh?
It seems the reset button allowed it to boot into the BIOS, but a regular boot wont?
Edit: Still wont boot into BIOS or POST though, I'm met with a blinking line that's been there for over 10 minutes now.

K9N2 SLI Platinum BIOS Flashing.

I have a new K9N2 SLI Platinum and as yet no processor. The best deals look like they are for the Phenom 8xxx series of triple core machines, but they are only supported by BIOS 3.2 (or later). My board is of course at 3.1. The question is whether the board will run enough to be able to flash the BIOS to the new version using an unsupported processor or do I need to have a supported one ? If it is the latter I think I will go for a fast X2 rather than a triple or quad core, I don't for the most part run more than 2 processes that consume a lot of resources.
Thanks
Jim

You'll need a 1.4Mb floppy drive to flash the BIOS.
Go ahead and get an AMD 9850 BE or 9950.
(Personally I'd get the AMD 9850 BE and OC it to 2.6 Mhz - cheaper than the 9950)
I built my rig with AMD 9850 BE - booted the first time it was fed power.
But, being the "good tech", I had downloaded the latest of everything from MSI support site,
and saved to Floppy and flash drive.
(The CD you get with the M/B does NOT have the latest BIOS/Drivers)
The very FIRST thing I did was update the BIOS to version: 3.2
After that, just load your OS and install the drivers.
Good Luck.
-Neut.

MSI K9N2 SLI Platinum problem (Mobo dead again?)

Ok, its been more than 4 months since my computer have been "dead". I went through two RMA for my mobo MSI K9N2 SLI Platinum and I went through RMA for my AMD cpu chip twice. Just today I decided to put the parts together when I got my new chip. Upon putting the parts together and turning the machine on, I get nothing. No post beep, nothing on the screen of the monitor. My PSU fan is spinning, I still get the red light indicator on my motherboard as I always have been in the past.
I put the parts with 1 stick of RAM next to the CPU.
My components for the following:
MSI K9N2 SLI Platinum
AMD 64 X2 5600+
1 stick of 2 GB Corsair Memory
650 Watts Corsair PSU
Does anyone know what else to do? It seems like my options are getting dried up and I feel like I want to ask for a refund since my motherboard is still under warranty, if that's possible.

Wait slow down here. You're saying that I supposed to hear a beeping sound when I power on? If so, I heard none. I am hard of hearing myself by the way.
*Not sure what you mean el-jack?
Quote from: Fredrik on 30-April-09, 06:03:16
Are there more things connected to the same el. jack? - Have a feeling I asked you that before!?
This is not 100% true, but if nothing works there is a power failure. If some things work and there is no beeping you can guess towards the processor. With beeping memory climbs up the ladder as the prime suspect.

K9N2 SLI Platinum / Phenom II 940BE overvolting and buzzing at load

I have seen many posts related to this issue, but have found no solution. The only thread which seemed to be going somewhere went off topic and was closed before anything could be resolved
My Phenom II 940BE, at load, is constantly being overvolted between 1.37-.38 and 1.40v. In the BIOS, after a fresh CMOS reset, I see the processor is set to 1.80v in the cell menu. This is a false reading, though, since the hardware monitor still has it between the aforementioned 1.37-.38 and 1.40v. Regardless, the lowest setting I have available with the CPU voltage setting in the Cell Menu is 1.375v then AUTO.
I have tried using many BIOS images with freshly cleared CMOS (remove battery, power cables from motherboard, wait a few minutes etc.): 3.4 3.5 and a MSI tech provided 3.6B1 BIOS all produce the same behavior.
When my CPU is at load, a light buzzing sound can be heard from the CPU area of the motherboard. This is especially noticeable when cool n quiet is enabled and the system decides to go from 800MHz to 3GHz, the buzzing is for the duration of the up-clocking until clocked back to 800MHz. I had the same issue on Vista x64 as well as Win 7. After some time at 3GHz the buzzing seems to go away, but may be drowned out by a fan or two.
Has anyone found some sort of resolve for this issue?
System Specs:
K9N2 SLI Platinum
Phenom II 940BE stock
Stock AMD cooler
8 gig of OCZ DDR-II 800 RAM (OCZ2N800SR2G) at stock
BFG GeForce 9800GT 1gig stock
Windows 7 X64 RTM
EDIMAX Wireless card 802.11n
Enermax Liberty Power Supply 500W (link)
2x Samsung Ecogreen 500gig in RAID0
Pioneer DVD-RW (SATA)
Onboard sound

Problem 1: solved. The metal curly thing by the RAM was buzzing. Unfortunately I do not have a hot glue gun and pressing on it with an eraser from a pencil did not alleviate buzzing, so removing 2 sticks of ram did it. I had 4x 2gb sticks. Taking out 2 stopped almost all of the buzzing sound, but sadly now I am running with only 4 gig of ram vs my mighty 8
Problem 2 still remains, the mystery of my CPU being at 1.38 - 1.40V instead of 1.350 when set to AUTO in the BIOS.

K9N2 SLI Platinum with Xigmatek Dark Knight S1283V Mounted - w/ Pictures

((I've updated my Temperature results in MY FIFTH POST DOWN; so please refer to the results in that post before jumping to conclusions!))
So.
I had some Credit available at a local Micro Center after returning a couple items to there that didn't work.
I decided to apply this credit to a new Cooler for my Phenom II 940 BE; and I settled on a Xigmatek Dark Knight S1283V. It is basically the same thing as Xigmatek's HDT-S1283; just with black nickle over its aluminum fins and copper heat pipes. Read a lot of reviews that seemed to put Xigamtek's HDT model Coolers "on par" with both the TRue120 and OCZ Vendetta. I settled on the Black Knight primarily because I didn't want one that was all shiny and flashy; and this one supported the "snap on" lever set up of the AM2+ socket; rather then having to removemy Mob and bolting it on.
Got it mounted; though it didn't quite mount the way I had wanted it to; was hoping to have vertical, it so the fan blew through it and out the back of the case, via the case fan on the back. But it mounts horizontal the AM2 Socket. So the Fan is flat and blowing downwards.
Anyway.
I am thus far not as impressed as I had hoped. It does not seem any better then my Stock Cooler; with my Phenom II 940BE on stock settings at 3.0ghz..
Idle temps around 44c.
Running Prime95 and it immediately jumped to 55c as soon as the "Torture Test" started, and gradually rose to 64c where its been holding there. I get the same results from my Stock Cooler.
This, is with Arctic Silver 5 applied to the base of the block as opposed to the thermal compound that came included with it.
Anyway, here are some pictures of it mounted on my K9N2 SLI Platinum.
Dark Knights Fan is blowing air DOWNwards.
Case Fan immediately to the left of the Dark Knight here, is blowing air out the back of the case.
The Case fan just above that, is blowing air into the case, as my HDD used to be there but no longer is.
The Case fan at the roof, of the case, is also blowing air into the case.
There is a large 120mm fan on the front of the case which is not shown, that is also blowing air into the case.
Left side of the Dark Knight; just barely touches the CIRCU PIPE Heat sink.
Right Side of the Dark Knight, just barely covers DIMM Slot 1. It pushed my Ram to the side by a couple Milimeters, so I moved them into Dimms slots 3-4.
Perhaps, the rest of my Fans need to be adjusted to work best with this; I am not sure.
But I expected to see at least a difference of 5 - 10 degrees celsius when compared with my stock cooler. I was, hoping to use this thing to push my chip into a higher Overclock. As it is, with my stock cooler, I can not overclock much higher then 3.4ghz. But if this Xigmatek is preforming about the same as my stock cooler, then I am afraid it just won't do for a suitable cooler for overclocking...

The Stock vCore for the chip is 1.350v.
I was able to go as high as 3.5gz with that. When I pushed to 3.6ghz, I had to push the vCore up to 1.375v.
At 3.7ghz, I had to push the vCore up to 1.4v.. and am now running at 1.450v for 3.8ghz.
This particular chip is claimed to be able to push 4.0ghz at 1.5v; though most people haven't been able to achieve this without Liquid Cooling. Infact, AMD set a Worlds Record with this chip, pushing it to 6.5ghz under Liquid Nitrogen... They did the same with the PhenomII x3 720BE.
Also; I was using the Stock Cooler on mine at 3.5ghz and was getting similar Temps to what you're getting. The Stock AMD cooler can't take that chip much pasted the 3.5/3.6 marks, depending on Chip, as bare in mind, not every chip of the same model is the same. Your 940BE may run differently from mine...
You're also using a different motherboard; so your Heat Pipes layout and configuration is different from mine; nt sure if this would have much effect on your CPU heat, don't think it should.... But it looks like your Mobo has more room to mount that V1 in a vertical position, with the fan blowing out the rear. Coolers like mine, can't mount that way.
I honestly believe though, if Xigmatek were able to supply their S1283 series coolers with a mounting bracket that would allow it to mount vertically like that, then it would dramatically improve its performance.
At present, mine is blowing air up, from the Video Cards, through the Cooler, and up towards the fans at the top which pulls it out the case. My video Cards are pushing 70c under load so I'm already pulling hot air. I also have two Thermaltake iCage's now, with 120mm Fans on the front, blowing air out the back. One of those is blowing air directly over the Cooler, and out the rear case fan.... which is why I think if I were able to mount a cooler in a vertical position, the CPU would probably run even cooler.

MSI K9N2 SLI Platinum - No Mem Voltage Settings?

I recently bought an MSI K9N2 SLI Platinum; along with a Phenom II 940 Black Edition and a set of OCZ Reaper 4gb PC8500/1066 DDR2.
I had, for awhile read that this motherboard was a great board and an excellent buy.
However, I can't seem to find a way to adjust the DRAM Voltage settings. I can change and adjust the memory timings, but not the voltage settings.
CPUz shows that my RAM is running at 1.8volts but it requires 2.1v! It also shows that all the mem timings are different from what they're set at in the BIOS.
Is there a way to unlock the Mem Voltage settings on this Motherboard?
If not, I may have to RMA it and get something else.

Don't have every bit of that info in front of my at the moment, but I can say, and show, where links are available...
AMD Phenom II 940 BE (Deneb)
MSI K9N2 SLI Platinum w/ BIOS v3.4
OCZ DDR2 PC2-8500 Reaper HPC 4GB Edition (OCZ2RPR10664GK)
EVGA Geforce 8800GT 512DDR3 x2/SLI w/Driver v180.08
Creative X-Fi Platinum - (Not installed at present, all software/drivers removed during troubleshooting)
Western Digital Caviar Green WD10EACS 1TB SATA 3.0Gb/s Hard Drive
ENERMAX Liberty ELT500AWT 500W ATX12V SLI Certified CrossFire Ready 80 PLUS Certified Modular Active PFC Power Supply
Logitech LX700 Keyboard/Mouse Combo - no longer available/not listed in products/could only find Logitechs original press release on it - Logitechs provided "set point" software is installed.
Hauppauge-WinTV-PVR-USB 2.0
Sony DVD-ROM IDE
NEC DVD RW IDE
The X-Fi Card, the two 8800GT's, and the Enermax PS' and both DVD drives, are carried over from my former system. All the rest were new, upgrade parts with a fresh and clean install of WinXP Pro w/SP3... Creative also came out with some new Drivers for that X-Fi sometime in 2008. I do not remember the Driver version or the exact date they were released, but I have tried them.
Also, I have tried rolling back the Geforce drivers back through several prior versions and ran tests with those as well, always with the same result.
I'll be removing one of the 8800GT's later on tonight when I get the chance and see what happens there.
One thing I noticed last night, is that the Mobo's Hybrid SLI is enabled with the OnBoard Video Port. I can not disable the Onboard, unless the Hybrid is disabled first. The cursor just skips over the listing for OnBoard when the Hybrid is enabled which is understandable.
However, when Hybrid is disabled and the settings saved, and system rebooted... its gets up to the WinXP Splash Screen then flashes a blue screen and automatically reboots and does this in a loop; until Hybrid is re-enabled.
At present, DRAM is manual configured in BIOS for 5.5.5.18 timings, and 2.20 voltage; as per manufacturer specs. CPU, is manually set at v1.350; which became available after re-flashing BIOS last night, and re-clearing CMOS.
Currently running system with the OnBoard Realtek Audio, using drivers from provided MSI CD.
Problems experience thus far...
Far Cry 2
Locks Ups/stuck in audio loop - often within 5 - 15 mins gameplay
Sometimes garbled Video; Alt Tabbing to Desktop and back into game clears this.
no error codes provided in Event Viewer
Crysis & Crysis Warhead
Locks up, often within 5 - 15 mins gameplay; usually locked up with a constant high pitch "Eeeeee" noise from speakers.
no error codes provided in Event Viewer
Unreal Tournament 3
Refuses to load any game maps, crashes to desktop
no error codes provided in Event Viewer
Second Life
Crashes to Desktop within 10 - 20 minutes
no error codes provided in Event Viewer
SPORE
Locks up within 5 - 15 minutes
no error codes provided in Event Viewer
Can browse internet for hours with no problems, no errors.
Can watch TV on my Hauppauge WinTV2000 USB PVR for hours, with no errors.
Can watch DVD's on any DVD software, for hours, with no errors.
Will try running Memtext86+ again tonight when I get home.

K9N2 SLI Platinum Blue Screen of Death when installing Windows XP

My hardware includes:
•   MSI K9N2 SLI Platinum Motherboard
•   Corsair XMS2 TWIN2X4096-6400C5
•   GeForce 9800 GT 512MB GDDR3
•   AMD Phenom X4 9850 Quad Core Processor, Black Edition 2.5GHz
4MB Cache 2000MHz [4000 MT/s] FSB
•   Thermaltake Ruby Orb Aluminum Core CPU Cooler
•   UltraX3 850 Watt ATX Modular Power Supply
•   [1] Western Digital 200MB7200 ATA133 [Not connected yet]
•   [1] Maxtor 80MB ATA133 Drive [Not connected yet]
•   [1] Western Digital 500GB 7200RPM 16MB SATA II HARD DRIVE
•   [2] Seagate 7200.11 ST3500320AS 500GB SATA Hard Drives With 32 MB Cache
[Not connected yet]
•   LG DVD-RW
•   Toshiba DVD-ROM [Not connected yet]
•   AMI Bios v02.61
•   Antec Full Tower case
After partitioning my drive with Fdisk I tried to install Win Xp. My plan was to format the drive with XP. XP starts up and runs through the initial system check then when it prepares to install I get the blue screen that says [my words] "Windows has shut down to prevent damage to your system. If drivers are mentioned try disabling them in the BIOS or get the latest bios update from the equipment manufacturer..." The error is:
Stop 0x0000007E on the next line
pci.sys - address f7480BFbase at f7487000 Datestamp 3b7d855c
Just never had these problems setting up a system and soon I will be able to say it took me 2 years to get this running. Hope someone can help. Thanks

Use XP Installation disk with SP2 or SP3 included to fix the BSOD.
Simple your XP installation disk is outdated and cause troubles with latest hardware.

SPDIF on K9N2 SLI Platinum

Hello, I just started to use the Geforce GTX 280 for my monitor and 50" DLP TV for dual video.
I have one DVI to HDMI to my monitor and the same setup to my TV. The TV is working like it should as a monitor but I am not able to get any sound. how am I able to get the sound to go through the SPDIF to my Blu-ray speaker system as it to has an SPDIF port?
AMD Phenom 9600 Quad Core
K9N2 SLI Platinum Mainboard
Geforce GTX 280 Video Card
OCZ Reaper v3 4GB 1066MHz
OCZ 750 Watt Modular PSU
Windows Vista 32bit SP2

If you want to use HDMI w/ audio, you must have vista or supported OS, and have spdif cable going from the video card to the motherboard connected. If your using DVI, then you must setup a separate cable from your sound card to the tv or stereo; which is usually just a male 3.5mm phono jack on both ends. Depending on your receiver or TV you may need a phono to RCA converter. However you can go digital if you like, using the rear spdif's and go str8 from optical to optical.
Keep in mind if you don't have ext. spdif. you can only go out analog from your soundcard or internally through HDMI which requires Vista or other supported OS.

K9N2 SLI Platinum and Phenom II 940

Similar Messages

Maybe you are looking for