K9N2 SLI Platinum - Testing

Ok so since I built this PC in February I have tested it with Windows XP SP3 Pro and Windows 7 Beta. Only issues I've had is with the HD Audio from Realtek. I read posts here about people having problems with their K9N2 SLI Platinum boards and maybe you're trying too hard.
My system specs are below, my PSU from Ultra is the 2nd Ultra PSU that I have owned, the first generation X-Connect 500W I had lasted from February 2005 to February 2009 and probably still has 5-10 years left on it. I upgraded to the 3rd Generation X-Connect 600W PSU, it's sufficient for single graphics card and powers everything just fine. Modular to keep airflow awesome.
I would only trust these PSU manufacturers:
Ultra
Corsair
Thermaltake
Enermax
Antec
I have only good reviews for Ultra and Enermax since I've owned them and they have never failed.
Back to the motherboard though, so my findings is that Windows XP Pro SP3 still has a few issues with this motherboard, mostly due to audio drivers, but not MSI's fault. Windows 7 Beta runs like a top, absolutely will be buying Windows 7 when it becomes available.
I had a red LED on my board for the longest time, then I figured out the issue, no floppy drive installed, after turning off the FDD controller, the red light went away.
CPU Idle Temps 23C with an Ambient Temp of about 70F, Load 30-32C same ambient temp. Stock HSF, 5 Case fans, no thermal compound, and excellent cable management.
Basically I completely love this board, but Realtek needs some better drivers for Windows XP.
I think I will be testing OpenSUSE on this after Windows 7 beta expires.
For those having troubles with this board I really don't know what to say, maybe try paying for the name when you buy PSU, Memory, Video. I went with Ultra, Corsair, and MSI and I did my research and I actually read many bad reviews of this board and still bought it. 2nd MSI board I've owned, love them both.
Anyway, thought I'd write something positive here, instead of seeing all the negativity towards MSI.

I have had bad experiences with Ultra as well.
PSU's: RAM: HDD: Mobo:
Thermaltake Corsair WD MSI
Apevia OCZ Hitachi Asus
Kingwin PNY Seagate Gigabyte
Corsair Kingston
Crucial

Similar Messages

K9N2 SLI Platinum video won't initialize with monitor connected

Hi,
I've gone through the RMA process with my vendor and I am on my third motherboard right now and I am still having an issue (so, basically, nightmare scenario here ). The first and second motherboard failures seemed slightly different but the failure seems to be the same for the second and third and it is making me think that another factor may be at play other than the motherboard. All of the failures have been with the integrated video (which is all I plan to use at the moment --I don't even own a PCI-E video card right now nor have any plans to get one in the near future).
In the first motherboard, everything seemed to work (as far as I could tell --4 green diagnostic LED's and all that) but no video signal was produced. Testing with an antediluvian Virge DX based PCI card (some of you kiddies may be too young to remember such things) did show normal booting with that video card (as far as I allowed it to go) and I suspect, from the pattern of hard drive activity, that with the integrated video the boot process was also normal (I just couldn't see it because of no video signal being produced). But that is past and has been RMA'd.
The replacement motherboard and the motherboard replacing the replacement motherboard, on the other hand, have seemed unable to initialize video whenever my monitor is connected but if the monitor is not connected, they work fine (but then video defaults to a 1028x768 mode and I cannot run my monitor at native resolution). Curiously enough, my second motherboard worked correctly twice before exhibiting the described behavior making me think, at the time, that I just got really unlucky and simply had had it fail shortly after testing it those two initial times.
Not being able to initialize video while the monitor is plugged in means that if I try to start it while the monitor is attached, the motherboard will not even POST and that the diagnostic LED's will be stuck at the video initialization stage (three reds, and one green at group 4).
Furthermore, if I start it with no monitor attached and plug the monitor in after I get 4 green LED's, it will start booting the OS (Windows XP) but the screen will go black when the Windows XP logo should be appearing. I can also leave it unplugged until it should be at the Windows XP logo stage (or plug it after the 4 green LED's and unplug it again before the video mode switch happens) and when I plug it back in I can see the Windows XP logo. However, as soon as it switches to the Windows XP desktop, I get a black screen.
And again, if I leave the monitor unplugged until the Desktop should be showing up and I plug it in at that point (or go through the process of plugging and unplugging the monitor while avoiding having video mode switches happen with the monitor plugged in) I do get a Windows desktop at the 1024x768 resolution. Once in the desktop, as far as I can tell, I can do anything there that I normally would be able to do (so I mostly have a working system, as far as I can tell). I have even installed drivers, verified that the sound works, etc.. I will still do a repair install at some point because I am not doing this the "right way" and I probably needed to do it anyway (though I think it's using the right kernel and everything --showing 3 CPU's, etc.) but I am not looking for answers with that as my issue shows up before the system even goes through POST. Again, note that I cannot even take advantage of my monitor's native resolution with the current kludge.
Curiously enough, if I try to switch to my native resolution of 1920x1200 it will do it but only by switching me to a virtual 1920x1200 desktop on a 1024x768 display (so there's no actual video mode switch involved and the desktop becomes bigger than what my monitor can show). It's as if part of the subsystem is reading the monitor and "knows" that it supports 1920x1200 but another part of the subsystem is just assuming some sort of 1024x768 default common lowest denominator for digital displays. I attribute this to the fact that video has been initialized with no monitor connected.
I originally had a 350W Enermax power supply (which worked as long as the monitor was not plugged in) supplying 32A on the +3.3V rail, 32A on the +5V rail and 26A on the +12V rail but I replaced it with the power supply shown on my profile (which was probably totally unnecessary as I'm only using the integrated video --but hey, I now have a blue light coming from my power supply so that makes it all worth it ). I suppose both power supplies could work badly with this motherboard model but it seems exceedingly unlikely that that would be the case (specially since everything works as long as there is no monitor plugged in during video mode switches).
I currently am running it, on cardboard, with a single stick of RAM (on the slot next to the CPU) and nothing else connected to it except the power supply (including JPW3 & JPW4), the CPU, a hard disk with a working Windows XP install, a mouse on the mouse port and a keyboard on the keyboard port (specification as on my profile minus one RAM module). I did play with RAM timings at the request of tech support but I can't imagine how it could be a RAM problem when everything works as long as a monitor isn't plugged in during video mode switches.
I did update the BIOS from 3.4 to 3.5. 3.5 did not seem to be available at the time of my previous motherboard and I knew it was a real long shot for this to be a BIOS issue that would be fixed with the 3.5 update (specially since the update mentions only CPU support stuff and nothing about video) but I am desperate. Yes, I have done the whole resetting the CMOS thing.
I am even considering the possibility that there may be some weird incompatibility between the video on this board and my monitor (under the assumption that, quoting Holmes, once you have eliminated the impossible, whatever remains, however improbable, must be the truth). I don't even know how that would work. Note that my monitor worked in my previous system with the digital input (my previous system is no longer available to me for testing --but I did get a chance to test it, after having problems with my first K9N2 SLI Platinum motherboard which I returned, and it worked). Note that my monitor works with the system in question (I simply cannot have it connected while there's a video mode switch under way). Note that the lack of a picture seems to be related to the motherboard as evidenced by it being stuck at the video initialization stage if I attempt to start it with the monitor connected.
Any wild ideas? I do not want to return this motherboard a third time and I specially do not want to return this motherboard a third time if it's something that can be easily fixed.

Quote from: Svet on 25-May-09, 02:21:06
Have you tried with just memory stick in 1st DIMM near to CPU socket and mainboard out of PC case?
Yes, I currently am running it, on cardboard outside the case, with a single DIMM (on the slot next to the CPU) and nothing else connected to it except for the power supply (including JPW3 & JPW4), the CPU, a hard disk with a working Windows XP install, a mouse on the mouse port and a keyboard on the keyboard port (specification as on my profile minus one RAM module). And it works,... as long as the monitor is not ever connected while video mode switches occur (including power on). And this is exactly how the previous motherboard which I returned also behaved.
Addendum: As an additional note, I have tried the other DIMM on the same socket by the CPU with the same results (everything works as long as there's no monitor connected during a video mode switch). I also managed to make a bootable Memtest86+ (is that what people use to test memory these days?) USB stick and I am running it right now. It has shown no errors right so far but it has only been running a few minutes. I do not really expect any memory errors to be at fault since they would have to be magical memory errors which only cause problems when there is a monitor connected while a video mode switch is happening but I'm desperate to try anything to find out what the issue is.

K9N2 Sli Platinum + SSD OCZ Vertex 3 = Slow Speed Problem [PARTIALLY SOLVED]

Hey folks,
I have a problem with my new SSD. I only get sequential reads of 140MB/s and writes of 114MB/s.
I think it is a driver related issue. I once got faster SATA2-like speeds but cannot reproduce the system settings again... Everything back to SATA1-like speeds after reboot.
First my pc specs:
MSI K9N2 Sli Platinum, BIOS v3.9
- 6 SATAII ports by nForce 750a SLI
- 2 ESATA (External-SATA) ports (back panel) by JMB363
- Supports storage and data transfers at up to 3 Gb/s
AMD Phenom II 965 Black
Patriot PV224G8500ELKB Viper II Series DDR2 4GB (2 x 2GB, CL5 PC-8500/1066MHz)
SSD SATAIII OCZ Vertex 3, 120GB, FW v2.11
LG Internal BlueRay BH10LS30
Windows 7 Ultimate x64
I only get very slow speeds with the SSD. I tried so many things that I am getting very frustrated now, I am even thinking about getting a new board and ram just to get the SSD up to speed...
1)
I installed Win7 first with all the default settings in Windows Setup from DVD. Default "IDE ATA/ATAPI controllers" driver was "Standard AHCI1.0 Serial ATA Controller".
SSD was connected to SATA1-port, On-Chip Sata Controller AHCI enabled in BIOS, Extra RAID/IDE Controller disabled.
All fine, but whichever benchmark I used (AS SSD, HD Tune Pro, Atto Disk Benchmark, CrystalDiskMark; other tools used: DriveControllerInfo, AIDA64/Everest, CrystalDiskInfo ) I got e.g. 140MB/s Read and 114MB/s Write sequentially (CrystalDiskmark, similar with random data AND only zeros ).
Trim working (it seems) with AHCI driver. I also changed to nvstor64 driver (nforce driver setup 15.56), with is marginally faster but not what you would expect from a SATAIII drive on SATAII controller.
2)
I installed Win7 using "diskpart" (Shift-F10) during disk setup, setting a cluster size of 64k instead of default. No real change.
3)
After reinstall of Win7 x64 (again...), I changed from SATA1 port to SATA6 port, also enabled Extra Raid/IDE controller set to AHCI as well.
Nothing changed. With all settings to default in Windows (ahci default driver), I then manually updated the ahci to nvstore64 driver in Device Management, rebooted.
Then a minute later after reboot I got the following Sequential speeds with CrystalDiskMark:
273MB/s read and 137MB/s write (random data) + 274MB/s read and 220MB/s write (with zeros) !!!
While I ran this benchmark Windows came up with a message: "You must restart your computer to apply these changes - Restart Now/Restart Later".
After the previos reboot, when I changed manually from AHCI to NVSTORE, I had changed nothing in the current session, apart from running CrystalDiskMark.
I did reboot and I was back to the slow SSD speeds again = 140/114 MB/s...
4)
I have tried every possible combination of mainboard SATA ports, drivers changing with nvidia setup/manually, deleting and disabling controllers (incl BSOD and startup repair :D ), chaning bios settings around, but I just cannot get back the faster speeds
There is never any change in speed, whether I use ahci or nvstore64, whichever benchmark I use, whether random or zeros...
5)
Could the SSD be broken, something internally preventing it from faster speeds (with this one random exception)?
Could it be that my K9N2 SataPorts only allows for / reduced to SATA1 speeds?
Am I missing something with the driver setup?
Do I need additional drivers for the extra JMicron Controller when using SataPorts 5/6 ?
I have no other mainboard to test this with...
Please guys, I am going to jump out of the window if I can't fix it... :(
Thanks, Mike

Hey guys - problem 'solved':
I tested the OCZ SSD Vertex 3 120GB with following sata3 controller card http://www.lycom.com.tw/PE-115H.htm.
The card itself works immediately (needs at least PCIe x4 slot, will work slower otherwise but still faster than the OCZ SSD @sata1 with nvidia chipset).
There is some raid setup, doesn't apply to me, the boot even with the card is really only a few seconds longer and not annoying at all. Windows (7 x64) needed a driver, supplied on CD (which is cheap and making noise like h**l). The card works w/o the driver but doesn't harm to install it...
Also, just to clarify, this sata controller card did not need any specific setup at all. Just put it in, plug in sata cable (I use akasa sata3-rated), maybe change boot device in BIOS (I didn't even have to), done - booting Windows as usual.
Benchmark CDM with sata controller card Lycom PE-115H:
http://img24.imageshack.us/img24/3845/cdmpe115hahci0x00.png
http://img850.imageshack.us/img850/7549/cdmpe115hahcirand.png
Speed is much better than before with nvidia chipset 750a SLI controller: sata1 (sata2 whenever it randomly worked):
http://img839.imageshack.us/img839/505/cdmahci0x0.png
http://img13.imageshack.us/img13/6258/cdmahci0x0sata6contnv64.png
Final thoughts:
Well, I am happy with the SSD speed now (PCIe limited to 5Gbps). However, I had to spent quite some time to get it working on my sata2-cabable mainboard. Finally, I had to buy a extra controller card to get it working reliably at speeds faster than sata1. There is hardly any useful information on why this problem occurs with (older) nvidia chipsets and OCZ (sata3) SSDs. I still think that OCZ must know about this problem, but regards this issue as low priority, while at the same time not planning on giving up on sales to people with nvidia chipsets. Maybe OCZ should just make a big sticker on the box the drives come in with something like "Does/Might not work with nvidia chipsets, please use third-party sata controller card or different SSD manufacturer". But then none of these potential customers would buy OCZ SSDs...
I will keep the sata3 controller, anyway handy to have, but return the OCZ Vertex 3 120GB and replace it with a SSD from a different manufacturer (Corsair Force GT, Patriot and OWC are not that great to get around here). The benchmarks for most people will not achieve the maximum advertised OCZ speeds anyway, so why not go with a brand that allows for some plug'n'play with some customer support.
Hope this post helps others like me with their nvidia chipset + sata1 speed problem
Cheers, Mike

K9N2 Sli Platinum - won't boot? Can't figure out problem.

Hey guys. My computer practically crapped itself the other day, and there were so many symptoms I'm not quite sure
what to even search for.
I've had this computer for about a year now. no problems since the day i built it.
specs:
Msi K9n2 Sli Platinum mobo
AMD Athlon 64x2 3.2 Ghz
2x BFG Nvidia Geforce 9800 GTX+
2x Cosair xms2 2gb ddr2
1000 watt BFG EX Series
Sony DvD drive
1tb western digital drive
So i was playing SC2 and my computer froze. So i restarted and it hung during windows loading.
I turned it off waited a few seconds and started... still hung. Cycled it and tried a couple more times.
Still nothing. Naturally i assumed it was a virus so i repaired my windows installation. After it finished it hung on
Windows has finished repairing your computer will now restart. I waited about an hour and decided to just restart
myself. Next time it booted asked me if i wanted to boot from cd and then it just shutdown like i pulled the plug.
Then i thought well i ruined my windows install. I tried booting again it did the same thing. So i just said screw it
ill reformat. But this time there was no signal from my graphics card. When i turn the computer on it will normally
be loud and then get quiet after everything has booted. But now it just turns on and stays loud because i suspect
it's still booting. So i took everything apart. Tried connecting and unconnecting everything. moving ram etc...
Ive got it to boot twice but after that it crashes before windows loads like a plug pull and it wont boot again.
I cant tell whats wrong it could be everything but nothing makes sense. I've built about 7 or 8 computers.
gotten rid of several viruses and bad hardware but I've never seen anything like this.
I tried checking the LED codes for the board. Leds 11 and 10 and 9 and 8 alternate red and green which means HDD and floppy drive are trying to boot.
but it does that even when my harddrive is not connected and it still wont show video. Ive even rotated the graphics cards and tried a 7900gs. nothing.
Edit: now led 6 and 7 are red.
please help me out. Thanks.

Yeah the case i have is the antec 1200. Never had a problem with heat before.
Ive tried it with just the ram and the cpu and it still gives me the lights so i
guess it must be the mobo or processor. I don't have another motherboard to test everything else on
all my other pcs are 5 to 7 years old.
I was thinking about keeping all my old parts and buying these as replacements:
MSI NF980-G65 AM3 NVIDIA nForce 980a SLI HDMI ATX AMD Motherboard
AMD Phenom II X4 965 Black Edition Deneb 3.4GHz 4 x 512KB L2 Cache 6MB L3 Cache Socket AM3 140W Quad-Core Processor
G.SKILL Ripjaws Series 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Desktop Memory Model F3-12800CL9D-4GBRL

K9n2 SLI Platinum DRAM timings will not stay

First off, I would like to say that I am posting this for my friend and that we both love MSI products. His setup is
K9n2 SLI Platinum,
Phenom 9950 140 watt black edition,
2 gigs OCz sli ready 8500 1066 1x2 kit,
BFG 8800 GTS G92 core 512mb graphics card,
and Corsair 650 watt PSU.
I don't at this time of writing have any screens, I can only explain whats going on. When he goes into BIOS and sets the Dram timings to 5.5.5.15 moves the voltage to 2.0, sets the Dram to run at 1066 which I think is 1.2.66, it reads at the top of the BIOS screen 1066. He then saves and exits reboots into windows runs CPU-z and it shows the timings have changed to 5.6.6.16, when he shuts down and goes back to BIOS it has changed there as well to the 5.6.6.16. The BIOS is the most current 3.2 also all the drivers and updates are the most recent for hardware and windows Vista home premium 32 bit. I Am trying to be as specific as possible to help you guys help us. The ram is in Dual channel Unganged. Please note it reads in CPU-z even with the 5.6.6.16 timings 1066 rather 533 DDR2 however the ram supports 5.5.5.15 in timings so I don't think that this could be good for it. We have done Memtest on the ram all test did fine we also used the windows version no errors on both test, We have not used Prime95 yet.
Any help would be great and much appreciated at this point. His computer has crashed twice, once was the Blue screen of death and the other was just a lockup. I also should mention CPU, mobo temps I think are well within specs CPU idle 37c load 45c graphics card at idle 40c load 46c. Thank you for reading Shucky.

You are most welcome! Ever so kind!
No performace lost, instead higher efficiency like you noticed.
Think of it like this:
A pipe with a big diameter can transport a lot of fluid.
A pipe with high pressure, where things have a high speed, can transport a lot of fluid.
A pipe where the diameter is not the same in both ends. Well, you can't say how much fluid will come out the other end, at least not without a lot of calculating and testing. (Like you also noticed. :D )
What is a pity is that program(mer)s have difficulties making use of all the cores. Phenom have four true cores. I think it will take about two years until all four can be put to full use, but if there ever is any real use in using all four cores is hard to say and a different question.
Sure AMD and Intel and Microsoft et al have found ways of distributing processor work, but they are far from optimized. And it isn't easy: Think of the project your work group got from your chief or teacher: How many should be involved? Or if you are 300 people in your dorm, or even just four of you in your family, should all help out with the washing up after supper?
No, is the best answer to that. So what has begun is developing processors, with a variety of cores. One may - as a silly example - make icons until or unless it can do better work somewhere else. - Not an easy thing making it do tasks like that, either! So that is why I did the washing up just now.

K9N2 SLI Platinum / K9N2 Zilent 4 RED lights

Hello. I got a problem with my K9N2 SLI Platinum / K9N2 Zilent...When i start the computer every thing gos as normal but there are 4 RED lights on the mainboard...but the hardriver's starts just like its about to start up. But the 4 RED lights are still standing. after maybe 40-60 sec it the first 1 turns green then the last 1 then all the lights blinks green and they all the lights stands on green and the computer starts up. But for a while a go it only took about 10sec to get the computer booting up. So what can be the problem with this long start up. I have take my computer apart then cleaned it but still the same problem. Now i need pro help and hopes someone out the can help me with this:) anyways i know 4 RED lights is a processor error but iv taken it out and if there was a processor error it would en start up at all?
Processor: Amd phenom 9650 2,3GHz
Ram: 4xkingston hyper x 1gb 800 RAM
Mainboard::K9N2 SLI Platinum / K9N2 Zilent

What PSU you use? List full details, read >>Posting Guide<<
Quote
Ram: 4xkingston hyper x 1gb 800 RAM
Use only 1 memory stick in 1st DIMM close to CPU socket.
Re-test.
Does it worked before or its new build?
Have you tried with barabone setup and mainboard out of PC case?

K9N2 SLI Platinum Fails Boot In Morning

System:
# AMD Phenom X4 9550
# MSI K9N2 SLI Platinum
# 2x2GB G Skil DDR2-1066 ( Bios DDR2 800/2.1 Volts )
# GeForce 8500GT
# 1x Seagate 500GB Sata
# 1x Maxtor 60GB ATA 133
# 650W PSU
Having Boot problems: Failed Boot this morning, System Shutdown 10 Hours ( PS AC On , LEDs Lite )
Failed at 2nd Green Light ( memory size check ), Reset and system Booted normal..
Previous: Overnight AC OFF , No Leds, System Failed Boot at 2nd Green LED and kept Recycling.
Several Power sw On/Off, system Posted with Bios Check sum, Booted defaults, System ok.
Ran OK all day..
Note: system Memory passes Memtst+ at 1066, 6 hours , no fails......
& Sandra Hardware tests ok
Question, Is Bios powered by PS when Power is off ( Leds are Lighted ) or could Battery be bad,
( I know, I will get another, But I don't think it is the problem )

You should have had early warnings if the battery was running low.
Could have been some kind of power problem during night, of course. If you mean by reset that you restarted the system, that would however suggest the PSU is on the limit.
There isn't much use in overclocking your memory, so I suggest you run it at 800.
And please specify your PSU a little better. Watts mean nothing substantial at all. It says mostly what profit the manufacturer wants.

K9N2 SLI Platinum with Xigmatek Dark Knight S1283V Mounted - w/ Pictures

((I've updated my Temperature results in MY FIFTH POST DOWN; so please refer to the results in that post before jumping to conclusions!))
So.
I had some Credit available at a local Micro Center after returning a couple items to there that didn't work.
I decided to apply this credit to a new Cooler for my Phenom II 940 BE; and I settled on a Xigmatek Dark Knight S1283V. It is basically the same thing as Xigmatek's HDT-S1283; just with black nickle over its aluminum fins and copper heat pipes. Read a lot of reviews that seemed to put Xigamtek's HDT model Coolers "on par" with both the TRue120 and OCZ Vendetta. I settled on the Black Knight primarily because I didn't want one that was all shiny and flashy; and this one supported the "snap on" lever set up of the AM2+ socket; rather then having to removemy Mob and bolting it on.
Got it mounted; though it didn't quite mount the way I had wanted it to; was hoping to have vertical, it so the fan blew through it and out the back of the case, via the case fan on the back. But it mounts horizontal the AM2 Socket. So the Fan is flat and blowing downwards.
Anyway.
I am thus far not as impressed as I had hoped. It does not seem any better then my Stock Cooler; with my Phenom II 940BE on stock settings at 3.0ghz..
Idle temps around 44c.
Running Prime95 and it immediately jumped to 55c as soon as the "Torture Test" started, and gradually rose to 64c where its been holding there. I get the same results from my Stock Cooler.
This, is with Arctic Silver 5 applied to the base of the block as opposed to the thermal compound that came included with it.
Anyway, here are some pictures of it mounted on my K9N2 SLI Platinum.
Dark Knights Fan is blowing air DOWNwards.
Case Fan immediately to the left of the Dark Knight here, is blowing air out the back of the case.
The Case fan just above that, is blowing air into the case, as my HDD used to be there but no longer is.
The Case fan at the roof, of the case, is also blowing air into the case.
There is a large 120mm fan on the front of the case which is not shown, that is also blowing air into the case.
Left side of the Dark Knight; just barely touches the CIRCU PIPE Heat sink.
Right Side of the Dark Knight, just barely covers DIMM Slot 1. It pushed my Ram to the side by a couple Milimeters, so I moved them into Dimms slots 3-4.
Perhaps, the rest of my Fans need to be adjusted to work best with this; I am not sure.
But I expected to see at least a difference of 5 - 10 degrees celsius when compared with my stock cooler. I was, hoping to use this thing to push my chip into a higher Overclock. As it is, with my stock cooler, I can not overclock much higher then 3.4ghz. But if this Xigmatek is preforming about the same as my stock cooler, then I am afraid it just won't do for a suitable cooler for overclocking...

The Stock vCore for the chip is 1.350v.
I was able to go as high as 3.5gz with that. When I pushed to 3.6ghz, I had to push the vCore up to 1.375v.
At 3.7ghz, I had to push the vCore up to 1.4v.. and am now running at 1.450v for 3.8ghz.
This particular chip is claimed to be able to push 4.0ghz at 1.5v; though most people haven't been able to achieve this without Liquid Cooling. Infact, AMD set a Worlds Record with this chip, pushing it to 6.5ghz under Liquid Nitrogen... They did the same with the PhenomII x3 720BE.
Also; I was using the Stock Cooler on mine at 3.5ghz and was getting similar Temps to what you're getting. The Stock AMD cooler can't take that chip much pasted the 3.5/3.6 marks, depending on Chip, as bare in mind, not every chip of the same model is the same. Your 940BE may run differently from mine...
You're also using a different motherboard; so your Heat Pipes layout and configuration is different from mine; nt sure if this would have much effect on your CPU heat, don't think it should.... But it looks like your Mobo has more room to mount that V1 in a vertical position, with the fan blowing out the rear. Coolers like mine, can't mount that way.
I honestly believe though, if Xigmatek were able to supply their S1283 series coolers with a mounting bracket that would allow it to mount vertically like that, then it would dramatically improve its performance.
At present, mine is blowing air up, from the Video Cards, through the Cooler, and up towards the fans at the top which pulls it out the case. My video Cards are pushing 70c under load so I'm already pulling hot air. I also have two Thermaltake iCage's now, with 120mm Fans on the front, blowing air out the back. One of those is blowing air directly over the Cooler, and out the rear case fan.... which is why I think if I were able to mount a cooler in a vertical position, the CPU would probably run even cooler.

K9n2 sli platinum will only boot/post when running single channel

Hey
I am having problems with the rig when i want memory to run Dual channel.
I have tried all bios settings (or at least i think so) and all memory slot combination (or at least i think so) without any luck.
When i put 2 sticks in dimm 1+2 I get nothing but a black screen.
When I then turn my pc off, putting 1 stick in dimm 1 it will boot and I get the message: DQS training failed on previous boot.
Mainboard: MSI K9N2 Sli platinum
CPU: AMD 5600X2 Windsor 2x1mb cache
HD: have tried with WD 250gb and hitachi 160gb sata2
Psu: Have tried with OCZ 500W and corsair 620W
Memory: Have tried with kingston pc5400 and Adata pc6400 both 1gb sticks
GFX: Have tried with GF8800GTS, ATI 1800XT and GF8500GT
CPU cooler: CM Gemini2
Motherboard have BIOS 3.1 ( so there should be no problem with running the cpu)
everything except for mainboard have been testet with other gear and is working 100%
Memory passed memtest with no errors.
Some facts
1 stick in dimm 1 = boot/post single channel
1 stick in dimm 2 = black screen.
1 stick in dimm 3 = boot/post single channel
1 stick in dimm 4 = black screen
1 stick in dimm 1 + 2 = black screen.
1 stick in dimm 1 + 3 = boot/post single channel
1 stck in dimm 2 + 4 black screen
1 stckk in dimm 3 + 4 black screen.
1 stick in 1 + 4 = Boot/postor black screen..cant remember but for sure not dual.
1 stick in 2 + 3 = boot/post or black screen..cant remember but for sure not dual
I have tried:
manual timming settings, both recommended and lower timmings.
Auto timmings
More volt to memory
More volt to cpu
Tried 800, 667, 553 and 400mhz
Tried sli memory disabled and enabled
Changing cpu ratio
Tried T2 and T1
Have tried load default settings
load optimized settings
everything on auto
well, that’s just about it and don’t know what to try next.
So if anybody have some input I would really appreciate it.
Regards
Jesper

Have you done that?:
Quote from: Stu on 13-September-09, 02:54:40
Have you tried taking the board out of the case and setting up outside on a flat anti-static surface? Maybe there is something shorting the back of the board where the DIMM slot is.
If no change:
Leave just one memory stick in 1st DIMM close to CPU socket,
ensure that system is stable the flash to the latest BIOS ==>
http://eu.msi.com/index.php?func=downloaddetail&type=bios&maincat_no=1&prod_no=1443
You can >>Use the MSI HQ Forum USB flasher<<
Once done re-test.

K9N2 SLI Platinum Brick

So I recently replaced a faulty ASUS Crosshair with what I was led to believe was a better board, the MSI K9N2. I had a little trouble getting it installed, but I managed to work around that with nLite and reinstalling windows with the RAID drivers. So I got it to boot to windows once, installed all the drivers, and restarted. I went into the BIOS to save the settings in the "USER SETTINGS" menu, and the BIOS froze up and crashed. I gave it a while in case it was going to do something, and then restarted. Nothing happened. The diagnostic LEDs were going between "Testing base and extended memory" and "Boot Attempt". I shut down, disconnected power, reset BIOS, and tried again. Now it's only showing "Boot Attempt" on the LEDs, and still nothing.
So tell me, is there anything I can do, or am I in for more of the same? And is there another motherboard that would be more appropriate for my system?
Also important: hardware I'm using now.
K9N2 SLI Platinum (MS-7374 VER 1.2)
AMD Phenom 9850 Black Edition
Corsair Gaming memory 2x2GB (CGM2X2G800)
BFG 8800 GTX OC X2
SeaSonic SS-650HT +3.3V@24A,+5V@30A,+12V1@18A,+12V2@18A,+12V3@18A, +12V4@18A,[email protected],[email protected]
Seagate 500GB 7200 RPM SATA 3.0Gb/s Hard Drive X4
Lite-On 52x32x52 CD-RW and a Samsung Writemaster DVD-RW
Creative X-Fi 7.1 Sound Card
Windows XP SP2 (without themes, or sample pictures, music, etc.)

Quote from: Fredrik Åsenius on 07-July-08, 06:03:51
From first post of yours I would have guessed at a processor problem. Hard to imagine you used that Phenom in the ASUS system too, but did you?
ModificatioNNNNN:
- "Agena 9850 (B3, 125W) 200 12.5 SINCE 3.1 "
- http://global.msi.com.tw/index.php?func=downloaddetail&type=bios&maincat_no=1&prod_no=1443
No, the ASUS was an AM2, not an AM2+, and didn't support the Phenom. I figured I'd pick up a new processor while I was getting a new motherboard. I can say it's not a processor problem, unless both the new Phenom and the old FX were bad, as I tried to boot with the board on a board, and tried both processors.

K9N2 SLi Platinum - Raid Issues

Components:
Enermax Pro82+ 525W
MSI K9N2 SLi Platinum
AMD 5400+ Black Edition
2x2Gb SUPER*TALENT DDRII 800Mhz CL4
MSI 8800GT 512mb
1 X WD Blue 500Gb Sata2
2 x WD Blue 320GB Sata2 (NEW SET)
Basically, I've had only the 500Gb HD as the main disk, Now I've got a set of 320GB's for Raid, which i'd like to add to my current setup without Re-installing OS coz the main drive contains necessary Data etc. So I Enable the Raid settings in Bios as outlined in the Manual. Setup the raid in the Mediashield Raid Bios. Windows Vista 32 simply Bsods at the Windows loading screen, with latest MB RAID drivers from MSI & Nvidia tested, still the same.
I've discovered in other threads, people experiencing something similar. According to what I've learnt is the best is going to have to Set the single 500Gb Drive into a stripe and re-install. I've tried other alternatives, like leaving the the 320's as single drives and setting up the raid through windows Mediashield, same problem after rebooting. Compared to My older rig, RAID seems to not work so starightforward on the K9N2. MSI should be more Specific with instructions and limitations to implementing a Raid.
That's not my biggest problem here though, I've disconnected the 500Gb due to critical data, I've only got the 320's in Ports 1 & 2. Setup Stripe raid in Bios. I cannot succesfully install Windows Vista or XP to the raid, Vista install remains stuck @ the decompressing files window. XP loads until it's about to boot the OS for the first time then Bsods. Using latest Floppy Raid Drivers too. Has anyone with this board got a Raid with OS installed? Am i missing something here? what am I doing wrong?
I'm still Testing, gonna pull out my Aged and beloved Hitachi 80Gb Sata1 Drive from the dead, install OS and then get this baby to work in Raid as I want it to, Hopefully......
Will report back..

The RAID implementation on this board is really obnoxious, if you have installed windows (XP/VISTA) prior to enabling RAID in the motherboard bios, windows will keep restarting itself at the windows load screen. Not an OS problem but the way the RAID controllers work on this motherboard.
My raid setup:
1 X WD 500GB BLUE (System C:\)(Single Stripe)(HAS TO BE IN IT'S OWN ARRAY IN MEDIASHIELD ROM for windows to work if RAID IS ENABLED)
2 X WD 320GB BLUE (Raid 0)(Stripe)
1 X LG Optical Drive (Also shows up in Mediashield post screen when Raid controller is ensbled)
Make sure to back up all data before setting up an array, setting up a array on a single HDD and selecting NOT to delete the MBR should keep your data intact. Booting up the system with the previous installation not deleted but now with the system HDD in it's own array you will continue to get BSOD and auto reboots.
V3.3 Bios Settings:
1) Set 'RAID MODE' to 'RAID" within the Integrated Peripherals Menu.
2)Enable 'RAID' in the Sub-Menu "ON-CHIP ATA DEVICES" --> RIAD MODE set to RAID then enable the ports you want Raid enabled on. SATA 1.2.3.4 are NV raid 5.6 are JMICRON. I have have ports 1,2,3 & 4 enabled as all 4 of my drives are connected to those ports. Optical drives will automatically show up in Mediashield ROM post screen even if port is disabled, and once windows is reinstalled other HDD'S can be connected without having to enable raid or arrays and all will be seen as normal.
Now to install windows, had an issue with the Floppy raid drivers from MSI site so I used the MCP78 floppy from gigabyte
http://www.gigabyte.com.tw/Support/Motherboard/Driver_Model.aspx?ProductID=2819. Windows working and Raid 0 on 2X 320GB HDD. Once windows is installed to a single disk in this manner windows will work fine with sata raid disabled (deleting array in mediashield will delete MBR) and in IDE mode as but when raid is re-enabled it will detect the disk and work fine too. Another issue unresolved is that I couldn't successfully install to the Raid 0-2X WD 320gb blue stripe, anybody got windows installed successfully to a Raid 0-2X hdd stripe? Note, If installing to Jmicron you will need JM drivers.
Another issue I have since using Raid is that S3 mode is not working well at all. S3 is enabled in Bios power management and definitely worked previously when raid was disabled. Now I cannot get S3 suspend. When i choose sleep it goes into Hibernation, checked all vista settings in power management and it should go to sleep not hibernate. Any Help? When it comes out of sleep all the lights are red and I have to power it down, turn power supply off/on then post-> 'windows resuming' then only does it come out of hibernation, strange... Whether I choose sleep or hibernate this is what I'm getting. Using Vista 32, Nvidia driver version 15.24, display driver version 180.48. Jmicron drivers installed as well.
Components:
Enermax Pro82+ 525W
MSI K9N2 SLi Platinum
AMD 5400+ Black Edition
2x2Gb SUPER*TALENT DDRII 800Mhz CL4
2x1Gb SUPER*TALENT DDRII 800Mhz CL4
MSI 8800GT OC 512mb
1 X WD Blue 500Gb Sata2
2 x WD Blue 320GB Sata2 (NEW SET)
1 X LG Dvd-Rw
Hope this helps & thanks in advance.

Random Lockups K9N2 SLI Platinum

Hey guys, Ive been dealing with a very annoying issue with a random Windows lockup, when I mean lockup its a press the reset button lockup. At first I thought it was a faulty Hard Drive, I replaced that with a Fresh reload of Windows 7 64 Bit. This issue has been going on for a few months, even before the Hard Drive going bad.. Some days/weeks I can play games without a problem, the lockups only occur within the first 5 to 10 minutes of playing, If I make it past that I am good to go.. In the last week I ran Memtest86 v4.0 and 3dMark Vantage, I got no errors or lockup's on either test.
Right after I ran the 3dMark Test I checked the temp in the bios here is what I found CPU Temp 111 F and System Temp 84 F, Im sure this is higher when Im gaming
I have been also getting this error in the event viewer on a lockup:
Component: AMD Northbridge
Error Source: Machine Check Exception
Error Type: HyperTransport Watchdog Timeout Error
Processor ID: 0
Here is my PC build, Ive been thinking about getting a new case that vents the heat from the top, I think this case I have is storing a lot of heat, the case itself gets very hot while playing games, I have 4 120mm fans running to. I was orginally running SLI with the 9800GT, I rebooted one day and one of the cards went, I sent both back to PNY and got 2 new ones but only put one back in since the heat was just to bad, I have a spare card now.
COOLER MASTER Elite 330 RC-330-KKN1-GP Black SECC ATX Mid Tower Computer Case
MSI K9N2 SLI Platinum AM2+/AM2 NVIDIA nForce 750a SLI ATX AMD Motherboard
AMD Phenom 9950 Agena 2.6GHz Socket AM2+ 125W Quad-Core Black Edition Processor Model HD995ZXAGHBOX
CORSAIR XMS2 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel Kit Desktop Memory Model TWIN2X4096-6400C5DHX
CORSAIR CMPSU-750TX 750W ATX12V / EPS12V SLI Ready CrossFire Ready 80 PLUS Certified Active PFC Compatible with Core i7 Power
PNY VCG981024GXEB-FLB GeForce 9800 GT Hybrid Power 1GB 256-bit GDDR3 PCI Express 2.0 x16 HDCP Ready SLI Supported Video Card
Western Digital Caviar Black WD5001AALS 500GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive
Any help would be appreciated
Thanks

Quote from: GavinMS1 on 25-February-10, 08:17:04
Sounds exactly like the problem I was having when I upgraded to an AM3 965 Phenom-II from an AM2 6000+ and 800MHz DDR2 6GB to 1100MHz DDR2 @1066 8GB all at the same time. All I can suggest is to make sure your motherboard chipset drivers are current. Right now for 750a SLI Nforce the current driver from NVidia is SMBUS Driver (v4.74) WHQL, SMU Driver (v1.71) WHQL. That is in the v15.49 download from the NVidia website. Also make sure your video card drivers are also current. v196.21 WHQL is the latest from the NVidia website for windows 7 64 bit for 9 series cards. another thing you could try is updating you BIOS to the latets version for K9N2 Sli Platinum, it is v3.6. In this website at the top you should see a link to down load the FORUM FLASHER tool made by Svet (Hopefully he posts a reply to this as well, he would most likely be able to help you out more with this). There is also an info page containing instructions on how to use it somewhere on this website as well.
Im pretty good for keeping drivers updated, to double check I downloaded the Nvidia tool to check for updated drivers, says everything is up to date.. I havent updated the bios, Ive done it in the past on other machines and Im always a little scared to do it
I downloaded SpeedFan, here are some temps sitting idle, Im not sure what the temps should be, what do you guys think?
CPU: 163F
Remote Temp: 234F
Temp: 166F
Temp1: 97F
Temp2: 84F
Temp3: 205F
HD0: 100F
Core: 105F

MSI K9N2 SLI Platinum problems again

Like many of you all who suggested me to RMA my board couple weeks ago. Well, looks like I finally got the board back and I decided to give it a go. Put in my computer parts (CPU, Ram, using on-board vga/dvi) and gave it a go. I turned on and then I see the same red light that occurred to me in the previous problem that I had before sending it in. I am thinking MSI didn't thoroughly test the board enough? I tried sticking the memory stick in different slots to see if that would help, still no go. I switched/changed cpu I contacted MSI and they said to reseat the CPU and check PSU. I told them that my PSU is brand new (Corsair 650TX) and confirmed them that it is indeed working. I took it out of the case to test by putting a cardboard underneath the motherboard using only 1 stick of ram in DIMM1 slot. Reseat/re-inserted the CPU and heatsink fan in. Connect the DVI cable to the on-board dvi connection. Then I took a flat screw driver and turned it on, I saw the CPU fan spin and the PSU fan spinning but the same red light showed up. I am still stuck and wonder what other options I have left.
MSI K9N2 SLI Platinum
AMD64 X2 5400
2x2GB Corsair (I am only using 1 stick to test at the moment)
Using onboard video instead of my 8800GT
Corsair 650TX watts (tested and it is brand new)
I feel like I don't know what else to do except I could take it to a computer technician to have a second look at it. If anyone have suggestion, I'd be happy to try.

I have done all of the following you listed except for testing the CPU in another machine. I will bring the two cpu to a local shop and have them tested. I will report back.
Quote from: Svet on 06-March-09, 04:54:11
Do you have power cable for the CPU connected?
Does the CPU works in another machine?
Have you done >>Clear CMOS Guide<< with power cord removed?
Have you tested with mainboard out of PC case too? {With one memory stick in 1st DIMM close to CPU socket}
Does the CPU is properly installed?
Checked CPU for bent pins too?

MSI K9N2 Sli Platinum with 1090t Problem

If anyone can figure this out, they will help me alot.
I updated my bios from 3.8 to 3.9. and it didnt anything
Light indicator.
http://imageshack.us/f/691/bioch.jpg/
While mine is
Group4. Led 4
   Led 5 Blinking between eachother (red light)
Group3. Led 6 Red
   Led 7 off
Group2. Led 8 Off
   Led 9 Green
Group1. Led 10 Red
   Led 11 Off
My Conclusion is that the lights are messed.
I have both yellow and Green light at the bottom of my motherboard.
In the instructions it says
Green light means the computer is powered on
Yellow means computer is standby.
The yellow light is on 24/7 even if the computer is off
The green light is on when i turn the computer (which is right)
I installed DualCoreCenter From MSI and it causes bsod.
The computer was working fine until I ran Prime95. It shutdown. And than it shutdown twice a starting windows screen. It worked fine after a while, but it shutdown again now. I dont wonna turn it on again.
My problem is somewhat similar to this persons.
https://forum-en.msi.com/index.php?action=printpage;topic=126143.0
I previously had q9400 with asus p5qlpro. I didnt know how to reinstall the os. the only thing i had to was reinstall nvidia drivers for the 9600 gso.

Quote from: impossibledone on 11-August-11, 09:41:47
Recently installed a 1090T on N9N2 Diamond and did testing on K9N2 SLI Platinum. All good after I flashed to 2.8 (the correct BIOS for that CPU). I Had the same problem with CPU sticking to heatsink, It was not caused by heat, I suspect the socket is weak. I just carefully pried it off.
Did I miss something? How did everyone jump on the CPU cooler without knowing what sort of case it's installed in/# of fans/what size fans, etc...?
did you have the same problem with different bios?

MSI K9N2 SLI Platinum - Ram suport

Where can I find a list over the ram that is suportet and testet with MSI K9N2 SLI Platinum ??
I have been using OCZ2P10664GK it run at 2.2v but the motherboard did not register it correct.

http://www.msi.com/index.php?func=prodtestreport&maincat_no=1&cat2_no=171&cat3_no=&prod_no=1443
That is where to find all tested components.

K9N2 SLI Platinum - Testing

Similar Messages

Maybe you are looking for