K9N2 SLI Platinum

ok I've only seen 1 post from this same issue with this mobo. And right now I could use some help.
I've been out almost 3 months from a pc and this is the 4th mobo that I've went with. 1st try with a MSI board.
I'm setting up with the following:
AMD 6400+ (3.2GHz)
8Gb DDR2 800 Gskill Ram
250 SATAII WD HDD
750W SilverStone powersupply
Light-On Dvd/Cd-Rom Combo Drive.
Also have a 9800Gt XFX Gfx Card (512MB )
Toss everything in, simple setup with a single 2GB Stick of Ram in the pc. No Gfx Card went to use on board, and would not show any video feed. I would assume this could be a issue from my parts, but I've tried everything out in this to another pc also tried using a single 1GB stick of GSkill ram as well as a 2.2Ghz AMD Cpu. And still same issues. Only thing I'm unsure about would be if some how my powersupply is not putting out enough power to run even the needed things for this. ( Mobo, CPU, heatsink, HDD, CD-Rom, 1 stick of Ram ) But still get nothing even after 2 days of messing around with it, and I'm unable to find any thing much about the LCD lights from the mobo on line.
The combo that I get when I go to boot:
LED15 - Green
LED16 - Orange
Group4:
LED4: Red
LED5: Off
Group3:
LED6 - Red
LED7 - Off
Group2:
LED8 - Off
LED9 - Green
Group1:
LED10 - Red
LED11 - Off
From what this shows in the book that I get the only thing that matches up with this combo would be a memory Detection Test. And it says that if the LEDs will hang if the memory module is damaged or not installed properly. But my only problem with this is: I've tried 8 different sticks of ram in this. 4 of them were 2GB Sticks, then the other 4 were 1GB sticks.
So could it be a issues with the mobo. And for the question, I've had this mobo now for 2 days. I received it just Wed's the 19th. The only other thing that I'm unable to test out or swap would be a powersupply. I was thinking if it comes to question this, I would get a tester for it due to thats the one thing I do not have.
Would like to see if this is a issue that I share alone, or if there is others with this issue or have ran into this. Also would be great, I'm willing to see what I can do to help it. I've tried almost everything possible with what I have. Testing powersupply would be the last option that I have laying around to see if that carry s a problem.
Also for the ones who would questions, I've tried all the extra power ports on the motherboard wondering if that might be the issue and still same issues.
Thanks if you could help me. Even if you have a wim that might work, feel free to toss ideas up.

Quote from: bruce_andrews on 22-November-08, 07:01:32
You are correct.
Sorry I could not help more. Hopefully someone else can (the durn error LEDs do not have an explanation as far as I can figure out - they only seem to tell you where you are in the bootup process).
Well at least you were sitting here trying with me, but I can say I figured it out.
Quote from: Fredrik on 22-November-08, 09:12:08
What BIOS have you got?
You might try to run outside the case, if you haven't.
BIOS would not be able to tell you or at least I would not have been. Other then it was out of the box.
But your idea of running out of the case would have worked if I not had gotten it before logging into here again with it up and running.
Seems as something that I had or was in the case was shorting something out within it so I just redid it all and putting each part in as I go. Right now only 3 things left, 4Gb more of Ram, then the sound card and everything is in working order again.
Thanks for the help and the response here guys/gals.

Similar Messages

  • K9N2 SLI Platinum Blue Screen of Death when installing Windows XP

    My hardware includes:
    •   MSI K9N2 SLI Platinum Motherboard
    •   Corsair XMS2 TWIN2X4096-6400C5
    •   GeForce 9800 GT 512MB GDDR3
    •   AMD Phenom X4 9850 Quad Core Processor, Black Edition 2.5GHz
                    4MB Cache 2000MHz [4000 MT/s] FSB
    •   Thermaltake  Ruby Orb Aluminum Core CPU Cooler
    •   UltraX3 850 Watt ATX Modular Power Supply
    •   [1] Western Digital 200MB7200 ATA133 [Not connected yet]
    •   [1] Maxtor 80MB ATA133 Drive  [Not connected yet]
    •   [1] Western Digital 500GB 7200RPM 16MB SATA II HARD DRIVE
    •   [2] Seagate 7200.11 ST3500320AS 500GB SATA Hard Drives With 32 MB Cache   
                    [Not connected yet]
    •   LG DVD-RW
    •   Toshiba DVD-ROM  [Not connected yet]
    •   AMI Bios  v02.61
    •   Antec Full Tower case
    After partitioning my drive with Fdisk I tried to install Win Xp. My plan was to format the drive with XP. XP starts up and runs through the initial system check then when it prepares to install I get the blue screen that says [my words] "Windows has shut down to prevent damage to your system. If drivers are mentioned try disabling them in the BIOS or get the latest bios update from the equipment manufacturer..."  The error is:
    Stop 0x0000007E  on the next line
    pci.sys - address f7480BFbase  at  f7487000  Datestamp 3b7d855c     
    Just never had these problems setting up a system and soon I will be able to say it took me 2 years to get this running.  Hope someone can help. Thanks

    Use XP Installation disk with SP2 or SP3 included to fix the BSOD.
    Simple your XP installation disk is outdated and cause troubles with latest hardware.

  • K9N2 SLI Platinum video won't initialize with monitor connected

    Hi,
    I've gone through the RMA process with my vendor and I am on my third motherboard right now and I am still having an issue (so, basically, nightmare scenario here  ). The first and second motherboard failures seemed slightly different but the failure seems to be the same for the second and third and it is making me think that another factor may be at play other than the motherboard. All of the failures have been with the integrated video (which is all I plan to use at the moment --I don't even own a PCI-E video card right now nor have any plans to get one in the near future).
    In the first motherboard, everything seemed to work (as far as I could tell --4 green diagnostic LED's and all that) but no video signal was produced. Testing with an antediluvian Virge DX based PCI card (some of you kiddies may be too young to remember such things) did show normal booting with that video card (as far as I allowed it to go) and I suspect, from the pattern of hard drive activity, that with the integrated video the boot process was also normal (I just couldn't see it because of no video signal being produced). But that is past and has been RMA'd.
    The replacement motherboard and the motherboard replacing the replacement motherboard, on the other hand, have seemed unable to initialize video whenever my monitor is connected but if the monitor is not connected, they work fine (but then video defaults to a 1028x768 mode and I cannot run my monitor at native resolution). Curiously enough, my second motherboard worked correctly twice before exhibiting the described behavior making me think, at the time, that I just got really unlucky and simply had had it fail shortly after testing it those two initial times.
    Not being able to initialize video while the monitor is plugged in means that if I try to start it while the monitor is attached, the motherboard will not even POST and that the diagnostic LED's will be stuck at the video initialization stage (three reds, and one green at group 4).
    Furthermore, if I start it with no monitor attached and plug the monitor in after I get 4 green LED's, it will start booting the OS (Windows XP) but the screen will go black when the Windows XP logo should be appearing. I can also leave it unplugged until it should be at the Windows XP logo stage (or plug it after the 4 green LED's and unplug it again before the video mode switch happens) and when I plug it back in I can see the Windows XP logo. However, as soon as it switches to the Windows XP desktop, I get a black screen.
    And again, if I leave the monitor unplugged until the Desktop should be showing up and I plug it in at that point (or go through the process of plugging and unplugging the monitor while avoiding having video mode switches happen with the monitor plugged in) I do get a Windows desktop at the 1024x768 resolution. Once in the desktop, as far as I can tell, I can do anything there that I normally would be able to do (so I mostly have a working system, as far as I can tell). I have even installed drivers, verified that the sound works, etc.. I will still do a repair install at some point because I am not doing this the "right way" and I probably needed to do it anyway (though I think it's using the right kernel and everything --showing 3 CPU's, etc.) but I am not looking for answers with that as my issue shows up before the system even goes through POST. Again, note that I cannot even take advantage of my monitor's native resolution with the current kludge.
    Curiously enough, if I try to switch to my native resolution of 1920x1200 it will do it but only by switching me to a virtual 1920x1200 desktop on a 1024x768 display (so there's no actual video mode switch involved and the desktop becomes bigger than what my monitor can show). It's as if part of the subsystem is reading the monitor and "knows" that it supports 1920x1200 but another part of the subsystem is just assuming some sort of 1024x768 default common lowest denominator for digital displays. I attribute this to the fact that video has been initialized with no monitor connected.
    I originally had a 350W Enermax power supply (which worked as long as the monitor was not plugged in) supplying 32A on the +3.3V rail, 32A on the +5V rail and 26A on the +12V rail but I replaced it with the power supply shown on my profile (which was probably totally unnecessary as I'm only using the integrated video --but hey, I now have a blue light coming from my power supply so that makes it all worth it  ). I suppose both power supplies could work badly with this motherboard model but it seems exceedingly unlikely that that would be the case (specially since everything works as long as there is no monitor plugged in during video mode switches).
    I currently am running it, on cardboard, with a single stick of RAM (on the slot next to the CPU) and nothing else connected to it except the power supply (including JPW3 & JPW4), the CPU, a hard disk with a working Windows XP install, a mouse on the mouse port and a keyboard on the keyboard port (specification as on my profile minus one RAM module). I did play with RAM timings at the request of tech support but I can't imagine how it could be a RAM problem when everything works as long as a monitor isn't plugged in during video mode switches.
    I did update the BIOS from 3.4 to 3.5. 3.5 did not seem to be available at the time of my previous motherboard and I knew it was a real long shot for this to be a BIOS issue that would be fixed with the 3.5 update (specially since the update mentions only CPU support stuff and nothing about video) but I am desperate. Yes, I have done the whole resetting the CMOS thing.
    I am even considering the possibility that there may be some weird incompatibility between the video on this board and my monitor (under the assumption that, quoting Holmes, once you have eliminated the impossible, whatever remains, however improbable, must be the truth). I don't even know how that would work. Note that my monitor worked in my previous system with the digital input (my previous system is no longer available to me for testing --but I did get a chance to test it, after having problems with my first K9N2 SLI Platinum motherboard which I returned, and it worked). Note that my monitor works with the system in question (I simply cannot have it connected while there's a video mode switch under way). Note that the lack of a picture seems to be related to the motherboard as evidenced by it being stuck at the video initialization stage if I attempt to start it with the monitor connected.
    Any wild ideas? I do not want to return this motherboard a third time  and I specially do not want to return this motherboard a third time if it's something that can be easily fixed.

    Quote from: Svet on 25-May-09, 02:21:06
    Have you tried with just memory stick in 1st DIMM near to CPU socket and mainboard out of PC case?
    Yes, I currently am running it, on cardboard outside the case, with a single DIMM (on the slot next to the CPU) and nothing else connected to it except for the power supply (including JPW3 & JPW4), the CPU, a hard disk with a working Windows XP install, a mouse on the mouse port and a keyboard on the keyboard port (specification as on my profile minus one RAM module). And it works,... as long as the monitor is not ever connected while video mode switches occur (including power on). And this is exactly how the previous motherboard which I returned also behaved.
    Addendum: As an additional note, I have tried the other DIMM on the same socket by the CPU with the same results (everything works as long as there's no monitor connected during a video mode switch). I also managed to make a bootable Memtest86+ (is that what people use to test memory these days?) USB stick and I am running it right now. It has shown no errors right so far but it has only been running a few minutes. I do not really expect any memory errors to be at fault since they would have to be magical memory errors which only cause problems when there is a monitor connected while a video mode switch is happening but I'm desperate to try anything to find out what the issue is.

  • SPDIF on K9N2 SLI Platinum

    Hello, I just started to use the Geforce GTX 280 for my monitor and 50" DLP TV for dual video.
    I have one DVI to HDMI to my monitor and the same setup to my TV. The TV is working like it should as a monitor but I am not able to get any sound. how am I able to get the sound to go through the SPDIF to my Blu-ray speaker system as it to has an SPDIF port?
    AMD Phenom 9600 Quad Core
    K9N2 SLI Platinum Mainboard
    Geforce GTX 280 Video Card
    OCZ Reaper v3 4GB 1066MHz
    OCZ 750 Watt Modular PSU
    Windows Vista 32bit SP2

    If you want to use HDMI w/ audio, you must have vista or supported OS, and have spdif cable going from the video card to the motherboard connected. If your using DVI, then you must setup a separate cable from your sound card to the tv or stereo; which is usually just a male 3.5mm phono jack on both ends. Depending on your receiver or TV you may need a phono to RCA converter. However you can go digital if you like, using the rear spdif's and go str8 from optical to optical.
    Keep in mind if you don't have ext. spdif. you can only go out analog from your soundcard or internally through HDMI which requires Vista or other supported OS.

  • K9N2 Sli Platinum + SSD OCZ Vertex 3 = Slow Speed Problem [PARTIALLY SOLVED]

    Hey folks,
    I have a problem with my new SSD. I only get sequential reads of 140MB/s and writes of 114MB/s.
    I think it is a driver related issue. I once got faster SATA2-like speeds but cannot reproduce the system settings again... Everything back to SATA1-like speeds after reboot.
    First my pc specs:
    MSI K9N2 Sli Platinum, BIOS v3.9
    - 6 SATAII ports by nForce 750a SLI
    - 2 ESATA (External-SATA) ports (back panel) by JMB363
    - Supports storage and data transfers at up to 3 Gb/s
    AMD Phenom II 965 Black
    Patriot PV224G8500ELKB Viper II Series DDR2 4GB (2 x 2GB, CL5 PC-8500/1066MHz)
    SSD SATAIII OCZ Vertex 3, 120GB, FW v2.11
    LG Internal BlueRay BH10LS30
    Windows 7 Ultimate x64
    I only get very slow speeds with the SSD. I tried so many things that I am getting very frustrated now, I am even thinking about getting a new board and ram just to get the SSD up to speed...  
    1)
    I installed Win7 first with all the default settings in Windows Setup from DVD. Default "IDE ATA/ATAPI controllers" driver was "Standard AHCI1.0 Serial ATA Controller".
    SSD was connected to SATA1-port,  On-Chip Sata Controller AHCI enabled in BIOS,  Extra RAID/IDE Controller disabled.
    All fine, but whichever benchmark I used (AS SSD, HD Tune Pro, Atto Disk Benchmark, CrystalDiskMark; other tools used: DriveControllerInfo, AIDA64/Everest, CrystalDiskInfo ) I got e.g. 140MB/s Read and 114MB/s Write sequentially (CrystalDiskmark, similar with random data AND only zeros ).
    Trim working (it seems) with AHCI driver. I also changed to nvstor64 driver (nforce driver setup 15.56), with is marginally faster but not what you would expect from a SATAIII drive on SATAII controller.
    2)
    I installed Win7 using "diskpart" (Shift-F10) during disk setup, setting a cluster size of 64k instead of default. No real change.
    3)
    After reinstall of Win7 x64 (again...), I changed from SATA1 port to SATA6 port, also enabled Extra Raid/IDE controller set to AHCI as well.
    Nothing changed. With all settings to default in Windows (ahci default driver), I then manually updated the ahci to nvstore64 driver in Device Management, rebooted.
    Then a minute later after reboot I got the following Sequential speeds with CrystalDiskMark:
    273MB/s read and 137MB/s write (random data)  +  274MB/s read and 220MB/s write (with zeros) !!!
    While I ran this benchmark Windows came up with a message: "You must restart your computer to apply these changes - Restart Now/Restart Later".
    After the previos reboot, when I changed manually from AHCI to NVSTORE, I had changed nothing in the current session, apart from running CrystalDiskMark.
    I did reboot and I was back to the slow SSD speeds again = 140/114 MB/s...
    4)
    I have tried every possible combination of mainboard SATA ports, drivers changing with nvidia setup/manually, deleting and disabling controllers (incl BSOD and startup repair :D ), chaning bios settings around, but I just cannot get back the faster speeds  
    There is never any change in speed, whether I use ahci or nvstore64, whichever benchmark I use, whether random or zeros...
    5)
    Could the SSD be broken, something internally preventing it from faster speeds (with this one random exception)?
    Could it be that my K9N2 SataPorts only allows for / reduced to SATA1 speeds?
    Am I missing something with the driver setup?
    Do I need additional drivers for the extra JMicron Controller when using SataPorts 5/6 ?
    I have no other mainboard to test this with...
    Please guys, I am going to jump out of the window if I can't fix it... :(
    Thanks, Mike

    Hey guys - problem 'solved':  
    I tested the OCZ SSD Vertex 3 120GB with following sata3 controller card http://www.lycom.com.tw/PE-115H.htm.
    The card itself works immediately (needs at least PCIe x4 slot, will work slower otherwise but still faster than the OCZ SSD @sata1 with nvidia chipset).
    There is some raid setup, doesn't apply to me, the boot even with the card is really only a few seconds longer and not annoying at all. Windows (7 x64) needed a driver, supplied on CD (which is cheap and making noise like h**l). The card works w/o the driver but doesn't harm to install it...
    Also, just to clarify, this sata controller card did not need any specific setup at all. Just put it in, plug in sata cable (I use akasa sata3-rated), maybe change boot device in BIOS (I didn't even have to), done - booting Windows as usual.
    Benchmark CDM with sata controller card Lycom PE-115H:
    http://img24.imageshack.us/img24/3845/cdmpe115hahci0x00.png
    http://img850.imageshack.us/img850/7549/cdmpe115hahcirand.png
    Speed is much better than before with nvidia chipset 750a SLI controller: sata1 (sata2 whenever it randomly worked):
    http://img839.imageshack.us/img839/505/cdmahci0x0.png
    http://img13.imageshack.us/img13/6258/cdmahci0x0sata6contnv64.png
    Final thoughts:
    Well, I am happy with the SSD speed now (PCIe limited to 5Gbps). However, I had to spent quite some time to get it working on my sata2-cabable mainboard. Finally, I had to buy a extra controller card to get it working reliably at speeds faster than sata1. There is hardly any useful information on why this problem occurs with (older) nvidia chipsets and OCZ (sata3) SSDs. I still think that OCZ must know about this problem, but regards this issue as low priority, while at the same time not planning on giving up on sales to people with nvidia chipsets. Maybe OCZ should just make a big sticker on the box the drives come in with something like "Does/Might not work with nvidia chipsets, please use third-party sata controller card or different SSD manufacturer".   But then none of these potential customers would buy OCZ SSDs...  
    I will keep the sata3 controller, anyway handy to have, but return the OCZ Vertex 3 120GB and replace it with a SSD from a different manufacturer (Corsair Force GT, Patriot and OWC are not that great to get around here). The benchmarks for most people will not achieve the maximum advertised OCZ speeds anyway, so why not go with a brand that allows for some plug'n'play with some customer support.
    Hope this post helps others like me with their nvidia chipset  + sata1 speed problem
    Cheers, Mike

  • Need help with drive installation for K9N2 SLI Platinum

     
    Hi
    I am new to the forum and to MSI
    This is my 6th computer build and first time using SATA and PCIe
    My hardware includes:
    •   MSI K9N2 SLI Platinum Motherboard
    •   Corsair XMS2 TWIN2X4096-6400C5
    •   GeForce 9800 GT 512MB GDDR3
    •   AMD Phenom X4 9850 Quad Core Processor, Black Edition 2.5GHz
                    4MB Cache 2000MHz [4000 MT/s] FSB
    •   Thermaltake  Ruby Orb Aluminum Core CPU Cooler
    •   UltraX3 850 Watt ATX Modular Power Supply
    •   [1] Western Digital 200MB7200 ATA133
    •   [1] Maxtor 80MB ATA133 Drive  [Not connected yet]
    •   [1] Western Digital 500GB 7200RPM 16MB SATA II HARD DRIVE
    •   [2] Seagate 7200.11 ST3500320AS 500GB SATA Hard Drives With 32 MB Cache   
                    [Not  connected]
    •   LG DVD-RW
    •   Toshiba DVD-ROM
    •   AMI Bios
    •   Antec Full Tower case
    The board set up fine, but I can’t figure out how to install my drives. The MSI directions are the worse I’ve ever seen, or should I say non-existent. They don’t even describe the bios entries… I am familiar with the bios, but don’t know all the settings for the board. I set the time and date and had to rearrange my drive placement on the board to have my 2 DVD drives show up on the secondary IDE Channel instead of the primary IDE.  The Western Digital 200MB7200 ATA133 is on the primary master IDE. I’m old fashioned so I still use FDISK to erase the old OS and partition the drive… I couldn’t see my SATA drive in FDISK even though I could see it in the bios. Now I want my Western Digital 500GB 7200RPM 16MB SATA II HARD DRIVE to be the system drive and the Western Digital 200MB7200 ATA133 to be a slave drive. My previous boards had raid but I just used them as additional slave drives.
    My goals: I want to have redundancy for my personal audio/video and my work. I will use the 2 Seagate 7200.11 ST3500320AS 500GB SATA drives for that.
    I also want 2 additional drives not purchased yet for my other data storage needs and for games
    My questions are:
    Can I use the SATA drive as the system drive if a drive is connected to the primary IDE?
    How do I set up Raid on this board? I actually want to use its capabilities this time.
    Does this board present any special problems with dual booting XP sp2 and Vista 64bit.
    If I put another set of Corsair XMS2 TWIN2X4096-6400C5 in anticipation of installing Vista 64bit will this cause a problem other than windows XP not seeing the additional memory.
    Is there additional documentation for this board somewhere?
    Please help…I have been working on this thing for 4 days straight. My last build took 2 hours not including software installation. Hope I stated everything you need to know. Thanks in advance  

    Hello!
    Advice no. 1 will be not to have everything connected at once. Have the chosen SATA and one of the DVD:s connected and install Windows. (Windows can only boot from bootable devices. It "jumps" all un-bootable.) Once you have a successful boot and happy with it, remove other things from the boot-sequence.
    Eh, some of your questions suggest you don't have the full manual, but a multi-lingual one. Check this out, bottom of the list:
    http://global.msi.com.tw/index.php?func=downloadfile&dno=6745&type=manual

  • K9N2 SLI Platinum / Phenom II 940BE overvolting and buzzing at load

    I have seen many posts related to this issue, but have found no solution.  The only thread which seemed to be going somewhere went off topic and was closed before anything could be resolved 
    My Phenom II 940BE, at load, is constantly being overvolted between 1.37-.38 and 1.40v.  In the BIOS, after a fresh CMOS reset, I see the processor is set to 1.80v in the cell menu.  This is a false reading, though, since the hardware monitor still has it between the aforementioned 1.37-.38 and 1.40v.  Regardless, the lowest setting I have available with the CPU voltage setting in the Cell Menu is 1.375v then AUTO.
    I have tried using many BIOS images with freshly cleared CMOS (remove battery, power cables from motherboard, wait a few minutes etc.): 3.4 3.5 and a MSI tech provided 3.6B1 BIOS all produce the same behavior. 
    When my CPU is at load, a light buzzing sound can be heard from the CPU area of the motherboard.  This is especially noticeable when cool n quiet is enabled and the system decides to go from 800MHz to 3GHz, the buzzing is for the duration of the up-clocking until clocked back to 800MHz.  I had the same issue on Vista x64 as well as Win 7.  After some time at 3GHz the buzzing seems to go away, but may be drowned out by a fan or two.
    Has anyone found some sort of resolve for this issue?
    System Specs:
    K9N2 SLI Platinum
    Phenom II 940BE stock
    Stock AMD cooler
    8 gig of OCZ DDR-II 800 RAM (OCZ2N800SR2G) at stock
    BFG GeForce 9800GT 1gig stock
    Windows 7 X64 RTM
    EDIMAX Wireless card 802.11n
    Enermax Liberty Power Supply 500W (link)
    2x Samsung Ecogreen 500gig in RAID0
    Pioneer DVD-RW (SATA)
    Onboard sound

    Problem 1: solved.  The metal curly thing by the RAM was buzzing.  Unfortunately I do not have a hot glue gun and pressing on it with an eraser from a pencil did not alleviate buzzing, so removing 2 sticks of ram did it.  I had 4x 2gb sticks.  Taking out 2 stopped almost all of the buzzing sound, but sadly now I am running with only 4 gig of ram vs my mighty 8 
    Problem 2 still remains, the mystery of my CPU being at 1.38 - 1.40V instead of 1.350 when set to AUTO in the BIOS.

  • K9N2 SLI Platinum raid setup after bios flash

    Hi
    I'm building a new system based on K9N2 SLI Platinum. Apart from a new 80 GB sys. HDD everything else is reuse from another MB (MSI K9N Platinum).
    Here is what is puzling me: Before trying to install WinXP i flashed the bios to 3.2 because of the included updates to the raid bios. Flashing went well, however in my setup I want the 80 GB HDD to be non-raid and the two 320 GB HDD to be raid1. I've set this up in bios so that only channel 5 and 6 is enabled for raid and would expect that the 80 GB HDD (channel 1) would show up as a normal sata HDD when starting up. But it doesn't - it is listed as 0.0 xxxx after the "press F10 to enter raid setup" message?
    This is strange because I had the same HDD setup on my old MSI K9N Platinum and there the 80 GB sata HDD was shown as a "normal" disk and not as a "appendix" to the raid list.
    Because of this I have problems installing WinXP on the 80 GB HDD
    Any suggestions?

    Hi BOSSKILLER
    Thanks for your quick response.
    Quote from: BOSSKILLER on 12-August-08, 00:14:44
    Well, leave the 80GB only and install XP over it.
    Then connect other two HDD's and enable RAID for them.
    Unfortunately this didn't help. As soon as I installed the Windows nVidia RAID SW it prompted med that it had registered  the 80 GB disk as a new disk that wasn't a member of any RAID. This happened everytime Windows XP was started.
    The trick was to add the 80 GB disk as a Spanned disk using the nVidia RAID BIOS setup utility. Install Windows XP (again) and the Windows nVidia RAID SW and setup RAID 1 on the other two sata disk.
    I don't think this is a great setup but it works. I hope that MSI will fix this issue in a later BIOS upgrade. It would be nice if the enabled/disabled for sata RAID setting actually worked.

  • K9N2 Sli Platinum - won't boot? Can't figure out problem.

    Hey guys. My computer practically crapped itself the other day, and there were so many symptoms I'm not quite sure
    what to even search for.
    I've had this computer for about a year now. no problems since the day i built it.
    specs:
    Msi K9n2 Sli Platinum mobo
    AMD Athlon 64x2 3.2 Ghz
    2x BFG Nvidia Geforce 9800 GTX+
    2x Cosair xms2 2gb ddr2
    1000 watt BFG EX Series
    Sony DvD drive
    1tb western digital drive
    So i was playing SC2 and my computer froze. So i restarted and it hung during windows loading.
    I turned it off waited a few seconds and started... still hung. Cycled it and tried a couple more times.
    Still nothing. Naturally i assumed it was a virus so i repaired my windows installation. After it finished it hung on
    Windows has finished repairing your computer will now restart. I waited about an hour and decided to just restart
    myself. Next time it booted asked me if i wanted to boot from cd and then it just shutdown like i pulled the plug.
    Then i thought well i ruined my windows install. I tried booting again it did the same thing. So i just said screw it
    ill reformat. But this time there was no signal from my graphics card. When i turn the computer on it will normally
    be loud and then get quiet after everything has booted. But now it just turns on and stays loud because i suspect
    it's still booting. So i took everything apart. Tried connecting and unconnecting everything. moving ram etc...
    Ive got it to boot twice but after that it crashes before windows loads like a plug pull and it wont boot again.
    I cant tell whats wrong it could be everything but nothing makes sense. I've built about 7 or 8 computers.
    gotten rid of several viruses and bad hardware but I've never seen anything like this.
    I tried checking the LED codes for the board. Leds 11 and 10 and 9 and 8 alternate red and green which means HDD and floppy drive are trying to boot.
    but it does that even when my harddrive is not connected and it still wont show video. Ive even rotated the graphics cards and tried a 7900gs. nothing.
    Edit: now led 6 and 7 are red.
    please help me out. Thanks.

    Yeah the case i have is the antec 1200. Never had a problem with heat before.
    Ive tried it with just the ram and the cpu and it still gives me the lights so i
    guess it must be the mobo or processor. I don't have another motherboard to test everything else on
    all my other pcs are 5 to 7 years old.
    I was thinking about keeping all my old parts and buying these as replacements:
    MSI NF980-G65 AM3 NVIDIA nForce 980a SLI HDMI ATX AMD Motherboard
    AMD Phenom II X4 965 Black Edition Deneb 3.4GHz 4 x 512KB L2 Cache 6MB L3 Cache Socket AM3 140W Quad-Core Processor
    G.SKILL Ripjaws Series 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Desktop Memory Model F3-12800CL9D-4GBRL

  • Need some advise - MSI K9N2 Sli Platinum

    Hello. I have some strange behavior of the system since the last week. Processor´s fan speeds up and down. Usualy is 3400-3600rpm; now speeds up to 5400-5600rpm and stay accelerate for a good while. I thought it could be some dust; yesterday I made a general cleaning of the hardware and also replaced the Thermaltake fan with another one which I have for replacement. The heatsink is firm, deos not have movements. The thermal grase is OCZ Freeze etc, something good,  seems to be hardened because heatsink stay firm. This was assembled some 16 month ago.
    I started again the PC, slow down the processor´s speed from OC 3.2Ghz to the basic 2.8 Ghz and the problem still go on. I thought this could be come system drivers problem, some sensor related. Then, I download the sys driver 15.49_nforce_winvista_win7_64bit_intern ational_whql from nVidia site and install it. Nothing, the problem is the same.
    also: http://i44.tinypic.com/120pix4.jpg
    The readings of Temperatures the TMPIN0 and TMPIN1, north and south bridge are ok. The TMPIN2 127°C is a dead sensor, it allways was like that from the beginning. Don´t pay attention to it.
    I´m really worried that thomething bad could happen and I have not a replacement for this mobo now.
    Could be some bad or crazy sensor which send some erroneous signal and that´s could be the origin of this situation?
    Does it exist the possibility the mobo get fried?
    I hope you´ll have the best advise for me.
    My best regards,
    Florin
    OS Windows 7 Ultimate x64
    MSI K9N2 Sli Platinum
    Phenom II x3 720 BE with Thermaltake Venus 12 cooler, 2.8Ghz
    4Gb (2x2Gb) Patriot (PVS24G6400LLKN) Extreme Performance Viper Series PC2-6400 CL4 DDR2-800 Dual Channel
    MSI nVidia GForce 9600GT / 512 Mb
    x2 WDigital Caviar Black bulk / sata 300 / 32Mb cache / 750Gb each
    DVD-RW Plextor px-810SA
    PS Xion Power Real 2.2 / 600W
    Aluminium case Viper XG with x3 120mm Ever Cool Spider fans (front, back, up)
    1 monitor LG Fantasy 19" / 4:3
    1 monitor Siragon 22" / 19:10
    Logitech 2.1 sound system (subwoffer + x2 three way speakers)
    Microsoft curve keyboard
    Microsoft IE mouse
    --I made you image clickable and
      fixed your link.  To see how, click the
      quote button, or edit if it's within an hour
      of your posting.
      Mike

    I'm confused.  You say to ignore the 127° reading, but then state you are concerned and talk about a false reading.  What reading and what exactly are you concerned with, the CPU temps?  If your system were getting that hot(127°C), you'd shut down or blow something.  I'm sure it's a false reading. 
    If you wish to remove the heatsink,  get something like Artic Silver 5 so you have a different paste to use.   Then, boot to the bios and leave it there for 15 minutes and shut down(you can simply hit the power off button this way).  Immediately, after shutdown, removing the power cord and pushing the power on button several times to drain the capacitors, try and remove the Heatsink carefully with some slight wiggle back and forth motion.  Hopefully, the heating of the TIM will make it pliable enough for easier removal.  DO NOT USE FORCE.

  • K9n2 SLI Platinum DRAM timings will not stay

    First off, I would like to say that I am posting this for my friend and that we both love MSI products. His setup is
    K9n2 SLI Platinum,
    Phenom 9950 140 watt black edition,
    2 gigs OCz sli ready 8500 1066 1x2 kit,
    BFG 8800 GTS G92 core 512mb graphics card,
    and Corsair 650 watt PSU.
    I don't at this time of writing have any screens, I can only explain whats going on. When he goes into BIOS and sets the Dram timings to 5.5.5.15 moves the voltage to 2.0, sets the Dram to run at 1066 which I think is 1.2.66, it reads at the top of the BIOS screen 1066. He then saves and exits reboots into windows runs CPU-z and it shows the timings have changed to 5.6.6.16, when he shuts down and goes back to BIOS it has changed there as well to the 5.6.6.16. The BIOS is the most current 3.2 also all the drivers and updates are the most recent for hardware and windows Vista home premium 32 bit. I Am trying to be as specific as possible to help you guys help us. The ram is in Dual channel Unganged. Please note it reads in CPU-z even with the 5.6.6.16 timings 1066 rather 533 DDR2 however the ram supports 5.5.5.15 in timings so I don't think that this could be good for it. We have done Memtest on the ram all test did fine we also used the windows version no errors on both test, We have not used Prime95 yet.
    Any help would be great and much appreciated at this point. His computer has crashed twice, once was the Blue screen of death and the other was just a lockup. I also should mention CPU, mobo temps I think are well within specs CPU idle 37c load 45c graphics card at idle 40c load 46c. Thank you for reading Shucky.   

    You are most welcome! Ever so kind!
    No performace lost, instead higher efficiency like you noticed.
    Think of it like this:
    A pipe with a big diameter can transport a lot of fluid.
    A pipe with high pressure, where things have a high speed, can transport a lot of fluid.
    A pipe where the diameter is not the same in both ends. Well, you can't say how much fluid will come out the other end, at least not without a lot of calculating and testing. (Like you also noticed.  :D )
    What is a pity is that program(mer)s have difficulties making use of all the cores. Phenom have four true cores. I think it will take about two years until all four can be put to full use, but if there ever is any real use in using all four cores is hard to say and a different question.
    Sure AMD and Intel and Microsoft et al have found ways of distributing processor work, but they are far from optimized. And it isn't easy: Think of the project your work group got from your chief or teacher: How many should be involved? Or if you are 300 people in your dorm, or even just four of you in your family, should all help out with the washing up after supper?
    No, is the best answer to that. So what has begun is developing processors, with a variety of cores. One may - as a silly example - make icons until or unless it can do better work somewhere else. - Not an easy thing making it do tasks like that, either! So that is why I did the washing up just now. 

  • K9N2 SLI Platinum / K9N2 Zilent 4 RED lights

    Hello. I got a problem with my K9N2 SLI Platinum / K9N2 Zilent...When i start the computer every thing gos as normal but there are 4 RED lights on the mainboard...but the hardriver's starts just like its about  to start up. But the 4 RED lights are still standing. after maybe 40-60 sec it the first 1 turns green then the last 1 then all the lights blinks green and they all the lights stands on green and the computer starts up. But for a while a go it only took about 10sec to get the computer booting up. So what can be the problem with this long start up. I have take my computer apart then cleaned it but still the same problem. Now i need pro help and hopes someone out the can help me with this:) anyways i know 4 RED lights is a processor error but iv taken it out and if there was a processor error it would en start up at all?
    Processor: Amd phenom 9650 2,3GHz
    Ram: 4xkingston hyper x 1gb 800 RAM
    Mainboard::K9N2 SLI Platinum / K9N2 Zilent

    What PSU you use? List full details, read >>Posting Guide<<
    Quote
    Ram: 4xkingston hyper x 1gb 800 RAM
    Use only 1 memory stick in 1st DIMM close to CPU socket.
    Re-test.
    Does it worked before or its new build?
    Have you tried with barabone setup and mainboard out of PC case?

  • K9N2 SLI Platinum - JPW2 connection essential? Also, question about diagLEDs

    I've been running a K9N2 SLI Platinum with a Phenom 9950BE and 2 Geforce 9800GT video cards for half a year now, running as stable as any computer could and I couldn't be happier. However, there's one thing that I've always had a question about - the molex connection on the board labeled JPW2. The manual says that JPW2 is "used to provide power to stable the operation of graphics card", but using the PCI-E connectors on the card appears to be adqeuate to running a stable system.
    In regards to this though, am I running the risk of an underpowering my motherboard not having JPW2 plugged in? The 24-pin and 8-pin power connectors on the board are of course plugged in and my concern is merely (hopefully!) academic at this point, but I'm just curious if not having power running through JPW2 would cause any problems down the line. My components are power hogs and I believe my power supply is up to it, but I'd love it if someone wiser than I could indulge my curiousity.
    Also, my diagnostic LEDS are reading something other than four green solid lights in normal operation (successful POST, Windows loaded and running). If you were to view the motherboard correctly mounted in the case, the order of the lights are: [G][R][R][G]. The manual refers to this as "BIOS Sign On - This will start showing information about logo, processor brand name, etc..." which is as incredibly unhelpful as it can be when it comes to this sort of thing. I state again that this doesn't effect normal operation - it's just another thing that I'm curious about.
    Thank you for helping me put my mind to rest!
    SPECS
    K9N2 SLI Platinum
    AMD Phenom 9950BE
    8GB G.Skill 800MHz DDR2 RAM
    2x Geforce 9800GT 1GB
    Seagate Barracuda ST3320620AS 320GB HDD
    SAMSUNG Spinpoint F1 HD103UJ 1TB HDD
    LITE-ON DH-20A4P-04 20x DVD-DL Writer
    Thermaltake W0116RU 750W ATX Power Supply
    CM Storm Sniper ATX Case
    Windows Vista Ultimate 64-bit

    Quote
    1. Will not plugging in JPW2 will adversely affect system performance stability.
    No, but its recommended to be connected.
    Quote
    2. Diagnostic led is shoring GRRG during normal use. No apparent adverse effects. Manual quite unhelpful. Cause?
    If the system works OK ignore it. Else ask here: http://ocss.msi.com/

  • K9N2 SLI Platinum Powers down.

    Big Problem starting! I purchased the K9N2 SLI Platinum board a couple months ago. For the first month everything went well except that my games would freeze such as Everquest. Never made any sense could freeze with in 5 minutes or, could be fine for over 5 days. Either way it was annoying so going through some information online I loaded optimal defaults on the Mobo BIOS and stopped loading the NVidia control panel at start up and it was great for a couple weeks no freezing. Now lately the computer just turns off. Like if you just pulled the power plug out. BOOM and its off. Could last 5 minutes or 5 days again. Very random. Nothing is over heating. Board is cool and CPU never goes higher then 49C. Most of the time I can hit the power button and turn the PC right back on again and its fine. Could blow again in 5 minutes or 5 days whether the PC is idle or I am playing a game. Now sometimes when it powers off. I can't turn it back on for a while. Ussually when this happenes there are no LEDs on in the Mobo. If I pull the power plug, let it sit for a min then plug it back in, it so far has powered back up ok. Another wierd thing is when I access the BIOS on start up now it seems to be shutting off. I want to say Power Supply may be? Prolly would be the first to try but would it explain the freezing games also int he beggining? It's 650watt and I am ussing the 8 pin rail since I have a pwoerfull CPU. May be there is a better recommended one for this type of Mobo. I tried the research the best one. My video card and ram worked great in my last PC but I had gotten the XFX 750 board and it was just horrible so I got rid of it. Rather of stayed with MSI which has been running better except for these issues. Any help would be greatly appriciated!
    **** UPDATES ARE IN MY REPLIES UNDER THIS. DIDN'T KNOW I COULD UPDATE IN THE SAME POST ****
    MSI K9N2 SLI Platinum Socket AM2+ Motherboard with Nvidia 750a SLI Chipset, PCI Express 2.0
    Logisys 650 Watt 24 Pin Green Gamer Power Supply w/ SATA and PCI-E
    AMD Phenom X4 9850 Quad
    OCZ Platinum XTC 4GB Dual Channel PC6400 Memory - DDR2-800MHz
    XFX GeForce 9600 GSO Video Card - 768MB DDR2, PCI Express 2.0, Dual Link DVI, SLI Ready
    Western Digital Caviar SE16 500GB Hard Drive - 7200, 16MB, SATA-300

    Ok i want to buy with my same company I bought the PSU from so I bought Prudent Way True One 1000watt nVidia Certified Quad SLI PCI-E w/ Six +12V Rails and Lifetime Warranty. They dont have the Corsair. I figure this one is beefy and solid. If it does power down too we should be able to rule out the PSU hopefully. If you think it's a bad choice please just say so. Should I be using 2 4pin rails or just the 8pin rail??? The manuals say you need an 8pin rail for my processor. I've seen some issues with using two 4 pins together saying it messes with the voltage or something?? What is a better way 2 four pins or just one 8 pin?? I've have checked for loose or frayed wires. No loose metal or screws in the case. Remember also it didn't do this for one whole month. Just some freezing with my everquest game. The only thing I don't like is how my pci-e video card sits in the mobo with this case. Looks like it can't go down all the way but if that were the problem, i figure it wouldn't work at all. I will take a day and rebuild this again in the case just to be safe like you said. I did take my time with mounting holes. Was very careful with this board. The power connections to the mobo seem a little wiggly but it just may be me. They seem to be making good contact. And also it just powered down again as i was typing this. Had to retype it. No shaking or bumping of the case. Plain aggravating this is!
    MSI K9N2 SLI Platinum Socket AM2+ Motherboard with Nvidia 750a SLI Chipset, PCI Express 2.0
    Logisys 650 Watt 24 Pin Green Gamer Power Supply w/ SATA and PCI-E
    AMD Phenom X4 9850 Quad
    OCZ Platinum XTC 4GB Dual Channel PC6400 Memory - DDR2-800MHz
    XFX GeForce 9600 GSO Video Card - 768MB DDR2, PCI Express 2.0, Dual Link DVI, SLI Ready
    Western Digital Caviar SE16 500GB Hard Drive - 7200, 16MB, SATA-300

  • K9N2 SLI Platinum Fails Boot In Morning

    System:
    # AMD Phenom X4 9550
    # MSI K9N2 SLI Platinum
    # 2x2GB G Skil DDR2-1066 ( Bios DDR2 800/2.1 Volts )
    # GeForce 8500GT
    # 1x Seagate 500GB Sata
    # 1x Maxtor 60GB ATA 133
    # 650W PSU
    Having Boot problems: Failed Boot this morning, System Shutdown 10 Hours ( PS AC On , LEDs Lite )
    Failed at 2nd Green Light ( memory size check ), Reset and system Booted normal..
    Previous: Overnight AC OFF , No Leds, System Failed Boot at 2nd Green LED and kept Recycling.
    Several Power sw On/Off, system Posted with Bios Check sum, Booted defaults, System ok.
    Ran OK all day..
    Note: system Memory passes Memtst+ at 1066, 6 hours , no fails......
    & Sandra Hardware tests ok
    Question, Is Bios powered by PS when Power is off ( Leds are Lighted ) or could Battery be bad,
    ( I know, I will get another, But I don't think it is the problem )

    You should have had early warnings if the battery was running low.
    Could have been some kind of power problem during night, of course. If you mean by reset that you restarted the system, that would however suggest the PSU is on the limit.
    There isn't much use in overclocking your memory, so I suggest you run it at 800.
    And please specify your PSU a little better. Watts mean nothing substantial at all. It says mostly what profit the manufacturer wants.

  • K9N2 SLI Platinum: USB mouse works, other USB devices iffy or not at all.

    I have a K9N2 SLI Platinum running now, and lately it's become rather flakey on me.  Windows Mobile device center cut out on me last month when I tried to update the phone software, which I guess should have been the first clue.  I notice that the flash drives I connect aren't showing up, and the new Ipod I bought last week doesn't show up at all, either. 
    Symptoms include:
    1. When I connect my HTC Excalibur up, Windows 7 realizes this is a phone, and starts up or installs Windows Mobile Device Center for me.  However, midway through installing the actual device, it stops and tells me the device is disconnected.  The phone is plugged in, and I've been afraid to touch it during this process.  On rare occasions, the phone actually is detected and installed, somewhere in the next dozen connections it reverts back to the drawing board, though.
    2. I have a bunch of flash drives that never show up on the computer now.  At least one of them showed up in the past, and transferred files just fine.  When I plug them in, I don't get the new device connected noise, and they don't show up in the System screen.
    3. I've managed to completely kill the batteries of two separate Ipods.  (Which actually worked out for me when they let me upgrade the new nano to a new classic).  It doesn't detect that anything is attached to the USB line.  Doesn't matter if I hook it up in disk mode, run "the 5Rs" or what, these little buggers starve to death on the line.
    4. Throughout all of these situations, two devices work no matter which rear USB slots I hook them to: the Microsoft Mouse, and my HP PSC 2700 printer.  So long as I don't pull them out while the machine is running, I don't have to do anything special to get Windows 7 to find and use them.  Unplugging the printer will get the device disconnected noise, but does not free up any resources to detect anything else attached.
    5. The front two USB slots don't work at all.  I don't think they've ever worked for me, so I'll deal with that mess sometime later.  Turning the computer off, unplugging these, and restarting with just the 4 rear slots enabled does not help the problem.
    What I've tried so far:
    1. Reinstalling Windows 7 after formatting the partition.
    2. Reinstalling the Nvidia nforce drivers from Nvidia's site using my board/processor specs.
    3. Reinstalling the software that normally detects these devices: Itunes, Windows MDC, etc.
    4. I've attempted to uninstall the USB drivers, but as the mouse connects here, that's been forcing a hard restart instead of shutting Windows7 down as normal.  On restart, mouse is reinstalled but problem remains.
    5. I've tried disabling Legacy USB drivers in the BIOS. No dice.
    6. I can't get a BIOS flash to work from the Live Update tools, (perhaps for the better), and the USB sticks aren't working to flash from one of those.  (Granted I can still boot and I'm otherwise stable).
    All I can think of is that maybe prior to reinstallation I pulled off something with CCleaner that I actually needed, but the reinstallation should have fixed that if it was a registry error.

    I'm sorry, I need to be a bit clearer, apparently.  The devices on the list were not plugged in at the same time.  Instead, I decided to see which if any devices would work by plugging them in one at a time.  The printer was plugged in for all of them, as was the mouse, then I repeated the one at a time process with both the printer and the mouse unplugged to see if anything new happened.  Results were posted line by line on the list above.
    Now then, I have managed to get my hands on an x86 version of Windows 7.  Surprise, surprise, it works.  Phone not only detects, but also installs.  When I plug in a Sandisk Cruiser, Windows 7 finds it, powers it up, installs drivers and assigns it a drive letter within about 5 seconds.  I haven't gotten around to installing the iTunes yet and getting the iPod running, but I suspect it'll work if everything else is showing up now.  Thus far, the only thing that hasn't worked when installed is the Logitec Gamepad, but then again I just plugged this one in to satisfy my curiousity.  There are probably some drivers I need if I want to actually play games with it.
    While this seems like it would solve the issue, the problem remains that I bought the board so I could eventually upgrade the RAM well beyond the 2GB I have installed.  Since x86 seems to only go up to 3GB, that's going to kind of defeat my purpose there.  Also, I've only got 30 days on this install, then I'm back to square one where I have to either use my x64 license/disc to get a legal, crippled copy going, or reinstall another x86 build.  Pretty sure copy protection will start kicking in soon on that. 
    Any Ideas?

Maybe you are looking for