K9N2GM-FIH CPU VCore correct manual settings not possible

Hello,
I have got the uATX K9N2GM-FIH Board and recently switched from a 4850e Athlon to a Sempron 140.
I am on BIOS Version 3.6.
After changing the CPU I cleared CMOS with the jumper and menually re-entered all settings in BIOS.
BUT:
The CPU Vcore is stuck at 1.35V, I wanted to lower this setting -> The voltage range from which I can choose is from 0V to 0.4V
This does not make sense...
I already contacted MSI two weeks ago via the official contact page but I did not get an answer.
Can you help me?
regards cdc42

Because the voltage defaults to 1.375V at the moment, if I set up any of the wrong values from which I can choose (0V - 0.4V) then the CPU vcore goes up to 1.45 V, this is way to high.
As I mentioned earlier this PC is used as a VDR as my SAT receiver, so it runs severeal hours a day in my living room. It should be as silent as possible, so undervoltiging/underclocking is my goal. I had to switch from a Athlon 4850e to the Sempron 140 because of the faster HyperTransport of the KUMA Sempron (VDPAU NVIDIA HD decoding), but that is another story...
With the AThlon 4850e I could setup correct Vcore values, with the Sempron it is as mentioned above.
My problem is the bug in this BIOS!

Similar Messages

Tariff scheme was created manually - upload not possible

Hi guys
I tried to upload german import numbers (purchased from BANZ provider). I used transaction /SAPSLL/LLNS_UPL101
Unfortunately I am getting the error message 'Scheme was created manually - upload not possible'
This scheme was already in the system (I guess it's standard) - how to deal with that?
For sure I need to delete an entry somewhere in the customizing - but where???
Your help is very appreciated..Thanks in advance!
Best regards
t.

Hi Tsunami,
If you maintained data manually and then after trying import from official XMLs you get this error.
Please clear these tables for your CTS scheme :
/SAPSLL/CTSNUM
/SAPSLL/CTSNUMT
/SAPSLL/CTSGEN
/SAPSLL/CTSGENT
or set field CREO in these tables to a value (for all commodity/tarrif codes) that will allow upload.
Probably a small ABAP report will help you in the fastest way.
Hope this helps,
Branislav Petricek
Edited by: Branko Petricek on Aug 2, 2011 2:54 PM

Correct smtp settings not sending

Having entered the correct pop and smtp settings into my IPad , mail can only be received not sent?
Any ideas?

iOS: Unable to send or receive email
http://support.apple.com/kb/TS3899
Can’t Send Emails on iPad – Troubleshooting Steps
http://ipadhelp.com/ipad-help/ipad-cant-send-emails-troubleshooting-steps/
Setting up and troubleshooting Mail
http://www.apple.com/support/ipad/assistant/mail/
Server does not allow relaying email error, fix
http://appletoolbox.com/2012/01/server-does-not-allow-relaying-email-error-fix/
Why Does My iPad Say "Cannot Connect to Server"?
http://www.ehow.co.uk/info_8693415_ipad-say-cannot-connect-server.html
iPad Mail
http://www.apple.com/support/ipad/mail/
Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
Or this - Delete the account in Mail and then set it up again. Settings->Mail, Contacts, Calendars -> Accounts Tap on the Account, then on the red button that says Remove Account.
 Cheers, Tom

Qosimo G20: Wlan WEP settings not possible running Config free?

Hi!
I have a Qosimo G20 running XP media center as OS.
Default Toshiba ConfigFree is installed.
Tried to find out how to set WEP key, but trying to do so in network config/settings task was halted with a message.
This message referring to Microsoft KB 871122.
Wireless Zero Configuration seams to be replaced by ConfigFree (or other software I'm not aware of).
I can not follow the instruction as I see it as I have ConfigFree installed.
Have anyone out there encountered this problem and solved it?
/Jonas

Hi
ConfigFree is a monitoring tool and helps you to monitor your connection. It allows you to pick up the information about used connections and helps you to have a better overview.
You can not use this tool for network configuration. If you want to do this please do this:
- activate the WiFi card at first
- go into Control panel > Network Connections > right mouse click on Wireless network and choose Properties
- under "preferred networks" add your WLAN and configure "Data encryption"
I hope that will help you.
Good luck!

Delete Facebook account in settings not possible

Hi,
I made a big mistake and put on the Ipad an old version of the backup, in this backup was the old Facebook adress saved.
The problem is that nobody rememberd on the password of this old facebook account. Now it is impossible to delete this
account in the settings. For some games I need this account, therefore has someone an idea what I can do ?? Thanks

I have the same issue and I don't have a place to enter a user name. So how did you change your user name? This problem is only on my iPad it did not follow my iPhone. It happened right after updating to IOS 7.1.1 and now I can't use Facebook for anything on my iPad. I have not changed my login on Facebook. Very frustrated.

Outgoing server settings entered correctly but will not update and tries to send under old settings

I can receive all of my emails correctly but can not send any emails. I have set up under a different program and it works fine. I have tried to update thunderbird by its settings and it does not provide any options?? I am running ubuntu 14.04lts.
My outgoing mail settings are correct but when thunderbird tries to send it uses old settings and does not update to the new mail server.
https://app.box.com/s/i27ulu2zq53iaq444boxoo7dp047qgyt
https://app.box.com/s/ivujudbq64mp8e5fd0pzkv5yt724bzta
https://app.box.com/s/zwj25bxv10sad27fcuov2ters23lcvu8
Thanks in advance

Application Basics
Name: Thunderbird
Version: 31.4.0
User Agent: Mozilla/5.0 (X11; Linux x86_64; rv:31.0) Gecko/20100101 Thunderbird/31.4.0
Profile Directory: Open Directory
(Unknown location)
Application Build ID: 20150112185638
Enabled Plugins: about:plugins
Build Configuration: about:buildconfig
Memory Use: about:memory
Mail and News Accounts
account2:
INCOMING: account2, , (none) Local Folders, plain, passwordCleartext
account3:
INCOMING: account3, , (imap) imap.netregistry.net:993, SSL, passwordCleartext
OUTGOING: smtp.netregistry.net:465, SSL, passwordCleartext, true
account5:
INCOMING: account5, , (imap) imap.netregistry.net:993, SSL, passwordCleartext
OUTGOING: smtp.netregistry.net:465, SSL, passwordCleartext, true
account6:
INCOMING: account6, , (imap) imap.netregistry.net:993, SSL, passwordCleartext
OUTGOING: smtp.netregistry.net:465, SSL, passwordCleartext, true
account7:
INCOMING: account7, , (imap) imap.netregistry.net:993, SSL, passwordCleartext
OUTGOING: smtp.netregistry.net:465, SSL, passwordCleartext, true
account9:
INCOMING: account9, , (pop3) mail.crochead.com:110, plain, passwordCleartext
OUTGOING: mail.crochead.com:465, SSL, passwordCleartext, true
account10:
INCOMING: account10, , (imap) imap.crochead.com.au:143, alwaysSTARTTLS, passwordEncrypted
OUTGOING: smtp.netregistry.net:465, SSL, passwordCleartext, true
account11:
INCOMING: account11, , (imap) mail3.bigcommerce.com:993, SSL, passwordCleartext
OUTGOING: mail3.bigcommerce.com:587, alwaysSTARTTLS, passwordEncrypted, true
Crash Reports
Extensions
Enigmail, 1.7.2, true, {847b3a00-7ab1-11d4-8f02-006008948af5}
Lightning, 3.3.4, true, {e2fda1a4-762b-4020-b5ad-a41df1933103}
Messaging Menu and Unity Launcher integration, 1.3.1, true, [email protected]
Provider for Google Calendar, 0.32, true, {a62ef8ec-5fdc-40c2-873c-223b8a6925cc}
Important Modified Preferences
Name: Value
browser.cache.disk.capacity: 204800
browser.cache.disk.smart_size_cached_value: 358400
browser.cache.disk.smart_size.first_run: false
browser.cache.disk.smart_size.use_old_max: false
extensions.lastAppVersion: 31.4.0
general.autoScroll: true
mail.openMessageBehavior.version: 1
mailnews.database.global.datastore.id: 912c1d9f-f79f-4a8b-9bf5-5c273fa7a3c
mailnews.database.global.indexer.enabled: false
mailnews.database.global.views.conversation.columns: {"threadCol":{"visible":true,"ordinal":"1"},"flaggedCol":{"visible":true,"ordinal":"3"},"attachmentCol":{"visible":false…
network.cookie.cookieBehavior: 2
network.cookie.prefsMigrated: true
places.database.lastMaintenance: 1424651152
places.history.expiration.transient_current_max_pages: 104858
plugin.importedState: true
print.print_bgcolor: false
print.print_bgimages: false
print.print_colorspace: default
print.print_downloadfonts: false
print.print_evenpages: true
print.print_in_color: true
print.print_margin_bottom: 0.5
print.print_margin_left: 0.5
print.print_margin_right: 0.5
print.print_margin_top: 0.5
print.print_oddpages: true
print.print_orientation: 0
print.print_page_delay: 50
print.print_paper_data: 0
print.print_paper_height: 279.40
print.print_paper_name: na_letter
print.print_paper_size_type: 1
print.print_paper_size_unit: 1
print.print_paper_width: 215.90
print.print_plex_name: default
print.print_resolution_name: default
print.print_scaling: 1.00
print.print_shrink_to_fit: true
print.print_to_file: false
print.print_unwriteable_margin_bottom: 56
print.print_unwriteable_margin_left: 25
print.print_unwriteable_margin_right: 25
print.print_unwriteable_margin_top: 25
privacy.donottrackheader.enabled: true
security.disable_button.openCertManager: false
security.disable_button.openDeviceManager: false
Graphics
Adapter Description: X.Org -- Gallium 0.4 on AMD KABINI
Vendor ID: X.Org
Device ID: Gallium 0.4 on AMD KABINI
Driver Version: 3.0 Mesa 10.1.3
WebGL Renderer: false
GPU Accelerated Windows: 0
AzureCanvasBackend: cairo
AzureSkiaAccelerated: 0
AzureFallbackCanvasBackend: none
AzureContentBackend: cairo
JavaScript
Incremental GC: 1
Accessibility
Activated: 0
Prevent Accessibility: 0
Library Versions
Expected minimum version
Version in use
NSPR
4.10.6
4.10.6
NSS
3.16.2.3 Basic ECC
3.16.2.3 Basic ECC
NSS Util
3.16.2.3
3.16.2.3
NSS SSL
3.16.2.3 Basic ECC
3.16.2.3 Basic ECC
NSS S/MIME
3.16.2.3 Basic ECC
3.16.2.3 Basic ECC

Trying to update software on my 4.3.3 itouch but getting message that server not available or settings not correct?

I am 9. Trying to update software on my I touch 4.3.3 and getting message in I tunes saying server not coinnected, but it is and then that settings not correct? Help please.

Update Server
Try:
- Powering off and then back on your router.
- iTunes for Windows: iTunes cannot contact the iPhone, iPad, or iPod software update server
- Change the DNS to either Google's or Open DNS servers
Public DNS — Google Developers
OpenDNS IP Addresses
- For one user uninstalling/reinstalling iTunes resolved the problem
- Try on another computer/network
- Wait if it is an Apple problem

I have Lion on my IMac and it is hooked up to I Cloud, however, even though all settings are correct I am not getting auto sync of calendars to my I Mac from my IPHone 4S or my iPad 1. Neither am I getting Photfrom my IPhone to my I Mac?

I have Lion on my IMac and it is hooked up to I Cloud, however, even though all settings are correct I am not getting auto sync of calendars to my I Mac from my IPHone 4S or my iPad 1. Neither am I getting Photfrom my IPhone to my I Mac?
Can someone set me straight?

Check system preferences to make sure you have iCal and your photostream checkmarked to TRUE.
If you still have problems, give us more details.
Also, make sure the calendar in iCal you're using/looking at is not "On My Mac", but actually an iCloud one.

Airport extreme will not fix problems or allow manual settings

So I have a recently purchased airport extreme and the dreaded "flashing amber light" problem, but I can't find a solution that works. When I open my airport utility it says it has found an airport extreme that is experiencing problems, and then gives all the specs of my airport extreme (e.g. name, ip address, etc.) and says it is reporting problems.
It then instructs me to press the continue button to resolve the problems. However, when I do that (or attempt to open the manual settings), it thinks and thinks and thinks while reading the configuration and then finally tells me that an error occurred while reading my configuration and I should make sure the airport is properly plugged in and in range of my computer, though it's plugged in properly and sitting immediately next to the computer.
I would also note that the internet works fine on my desktop (being run through the airport to my mac), but just will not work on the danged airport.
Any idea of what I can do now?

It opens up a new window, but still gives me the exact same error message about not being plugged in or in range, though it is both of those

Problems errors ram with cpu vcore change on k7n2 delta2 platinum

hello
i'm a french new owner of k7n2 delta2 platinum and i got something strange.
I have 2*512 PC3200 cas3 of kingston value ram with voltage 1.75 instead of 1.6v running in dual CAS 2.5/3/3/8 at FSB 195 like the cpu : 2500xp barton.
With occt and memtest86+ i'm stable with a CPU vcore at 1.725.After 195 the computer starts but not really stable. So i put the cpu vcore at 1.75 to put higher fsb and then i get thousands RAM errors with memtest. i tried with cas 3/3/3/11 and it was worst. On the bios B6 i tried with different settings : agressive, optimal, 1/1, auto, manual, patch ddr or not...and always the same. My PSU is 450w and i've 4 HD 1player 1 burner.
Of course i'm happy to reach 195 but i feel disapointed to be stop with this problem of vcore/ram

Quote from: osnavi on 23-September-05, 11:36:11
"...So i put the cpu vcore at 1.75 to put higher fsb and then i get thousands RAM errors with memtest..." I would say it's not the v. core but the CPU o/c. that gives that errors, as it make not sence to increase v.core only for itself.
Oh yes it does
The CPU and memory work hand-in-hand. If one is out of sync it can cause the other to start spitting out errors.
You are overclocking and that more of a scientific art, not an exact science.
Components react differently to an entire list of variables, especially the CPU/memory.
What you are trying to do requires trail and error testing however I agree the Kingston memory is holding you back at this point with the clock you are pushing
I would go for the most stable FSB settings that allow Dynamic Overclock to be enabled to SERGEANT before I would go for ultra High FSB because you will peak the system at its highest performance curve when you need the boost, and I would bet money that peak would be higher than any strait FSB over-clock you can hit stable.
Psychologically allot of people think their systems are not running the highest performance it can unless they set the system up at the highest FSB/multiplier and that is simply not true with dynamic overclocking enabled and correctly tuned with the rest of the components.

[AMD] problems errors ram with cpu vcore change on k7n2 delta2 platinum

hello
i'm a french new owner of k7n2 delta2 platinum and i got something strange.
I have 2*512 PC3200 cas3 of kingston value ram with voltage 1.75 instead of 1.6v running in dual CAS 2.5/3/3/8 at FSB 195 like the cpu : 2500xp barton.
With occt and memtest86+ i'm stable with a CPU vcore at 1.725.After 195 the computer starts but not really stable. So i put the cpu vcore at 1.75 to put higher fsb and then i get thousands RAM errors with memtest(even if i stay fsb 195). i tried with cas 3/3/3/11 and it was worst. On the bios B5 i tried with different settings : agressive, optimal, 1/1, auto, manual, patch ddr or not...and always the same. My PSU is 450w noname and i've 4 HD 1player 1 burner & a geforce 5200 o/c 10%.
Of course i'm happy to reach 195 but i feel disapointed to be stop with this problem of vcore/ram because i have not problem of temperature with a silent boost for cpu(52°c maxi), 3 fans for the box(35°c maxi) and copper memory heat spreaders for ram.
thanks for your answer

the thing to check is the vdimm voltage for the ram ... i'm pretty sure it should be around 2.6 volts .. try upping it one step
vcore is the voltage to the cpu and doesn't affect the ram

Lens Correction Manual Slider Bug!

Hello,
I've been having a problem with the Lens correction Manual Sliders. Constrain Crop selected.
The vertical and horizontal sliders are behaving more like the distortion slider.
When sliding left or right they are pulling from the center, rather than the right or left end.
Also, with the scale slider....If I scale down it shifts to the right. when I reset all the sliders to zero.
The image doe not reset to its original position.
Is this something that the Lightroom 4 team is aware of?
One all the bugs are fixed I look forward to its release! Your hard work on this software is appreciated!
Best, Pam

The vertical and horizontal sliders are behaving more like the distortion slider.
When sliding left or right they are pulling from the center, rather than the right or left end.
Well, they *are* distortion sliders (sort of), leaving the very center of the photo unchanged. This has not changed from LR3. I can see no bug there. Also keep in mind that the visual effect is very different from wide angle photos to tele photos. Photos made with a tele lens are more or less just changed in the aspect ratio, and not so much distorted like wide angle photos.
Also, with the scale slider....If I scale down it shifts to the right.
This can happen if you used the horizontal slider before, combined with "Constrain Crop" - because the usable part of the photo shifts to one side or another. In the same way, scaling will shift up/down if one used the vertical slider before. This is perfectly normal. Hint: Try the vertical and horizontal sliders independently, with scaling set to 50 (minimum) and "Constrain Crop" *OFF* to see what they do with the photo - that made it a lot clearer to me how they work.
when I reset all the sliders to zero. The image doe not reset to its original position.
Also normal, because if you reset the manual corrections after working with "Constrain Crop" enabled, only the manual corrections themselves are reset, leaving the crop&straighten tool at some "funny" settings. Go to crop&straighten and reset it, too.
In conclusion, I see no bugs here. I also fiddled with the various manual sliders, and could not see any behaviour that was different to LR3, which has no bugs in this respect as far as I know...
P.S. I am not sure if I quoted the last question correctly or not. I assume these two sentences belong together?

D70 manual settings with studio flash

I have a D70 and wish to use it with Bowen flash units with a remote wireless trigger. This is not the problem as I have two triggers both of which work fine. The problem is with the camera, I only ever use manual settings and keep losing the LCD display as I focus with the trigger attached. The image holds if the flash is open, but that is no good to me. Does anybody please know how I can hold the LCD display in the studio using manual settings.

That's correct. All that's being done is pretty basic symbol animation. Tweens, eases, a lot of symbols within symbols for easy switching of parts. What confuses me most is that it opens fine in CS5.5. What features might CS6 have/not have to completely break the file?
I also attempted to re-save the file in CS5.5 and then try opening it in CS6. This killed the program. Didn't even get as far as exporting a swf. All of my tools disappeared, all assets were corrupted, and the program just went on an endless loop of thinking and freezing.

Lightroom 3.4.1 Lens Corrections – Manual Tab Defaults

I'm running LR 3.4.1 on Windows 64bit OS. I just discovered some pictures shot recently with my 5D MKII have the Lens Corrections Manual tab Chromatic Aberration settings applied Red/Cyan = -17 and Blue/Yellow = +5. I hadn't applied these settings so went back and checked my Lens Profile defaults only to find this is the default for those settings. What I mean is when you double-click on the Manual tab slider titles 'Red/Cyan' and ‘Blue/Yellow,' or on the heading title 'Chromatic Aberration, these are the settings applied as "defaults." I would have expected the default to be '0' for both, and there does not appear to be anyway to reset them to '0' other than manually correcting each. I tried 'Reset Lens Profile Defaults,' but that only resets the settings in the 'Profile' tab.
It appears to have only affected one group of pictures and import of new pictures applies the Lens Profile correctly with Manual tab settings at '0.' But it still defaults to the non-zero settings for Manual CA when double-clicking as described above, which is probably how I screwed up on that one group of pictures.
Anyone have ideas in what is going on...or am I simply overlooking something obvious?

Thanks Lee Jay. I must have inadvertently set those when updating the camera profile. ALT key, 'Set Default' and selected 'Update to current settings' with them set back to '0' did the trick.

[865PE/G Neo2 Series] CPU VCore CPU Voltage funny looking after Flash Update 3.A

Hi There,
I have just updated the flash on my computer thru the LiveUpdate running on windows 2000 (without a floppydisk),... the flash ran thru without error and rebooted,... then i ran thru the BIOS settings and came to Frequency/Voltage Control,... BLIP said the computer and then i saw the CPU Voltage (V) saying = ╕65¤ ┐ (not really this sign: ¤ but it is as close as i can get it tiny o with a line on top and buttom of it)
However the system seems (so far (still with the SATA shutdown problem) ) be working fine,... as long as i keep CPU Vcore Adjust on NO,...
I tried reflashing the system,.. same result, i tried coldbooting,... same thing,...

sorry bout the "hijacking" thingi .....i am a newbie...sorry again...i already start a new topic ...thankss 4 your all help bye... come join in if u can helpthanks
me...i relly need some help ...
motherboard - MSI 865PE neo-2 Platinum edition...processor - P4P (Presscott) Pentium 4E 90nm 2.8 - 4GHz 1.25 - 1.40v...bought from U.S.A....
3d card - MSI GeforceFX5200 128mb....
RAM - 512 ddr333...
Optical drive - LG CD writer, Samsung DVD rom...
Floppy Drive - samsung normal Floppy drive
chasis - normal ATX icute Chasis....added 2 120x120x25mm fan an a 80x80x25 mm fan.....
Power supply - normal power supply....
monitor - Prolink 17inch
cpu cooler - Cooler Master Hyper 48(KHC-L91-U2)
3d card cooler - Cooler Master CoolViva(VHC-L61)
thanks
i relly need some help ...

K9N2GM-FIH CPU VCore correct manual settings not possible

Similar Messages

Maybe you are looking for