Kanban - Control cycle
Hello all!
I am trying to create a control cycle for Kanban in my test system. I have created replenishment strategy in Customizing for Kanban and this was transferred all to my test system. When I want to input the address for a vendor it says: Replenishment strategy in plant ... does not exist.
I suppose there must be a problem with my Replenishment strategy which I have created in Customizing for Kanban. I was not sure about what I need to specify. I have specified plant, type of Procurement:it is an external Procurement, working with Scheduling agreements, Order type - LP, GR - 101, Signal lock- 0. These are all information, which I have specified I was not sure about the rest.
Please could anyone help me ??
Hi,
I answered to few of the threads, hope it will help you, if required any further info please let us know.
Re: Implementing KANBAN-WM
Re: Creation of control cycles for lean WH
thanks
Om
Similar Messages
-
Hi team,
I was referring the below statement to understand the control cycle.
The Kanban Control Cycle business object is used to control the flow of information and material between the demand source and the supply source in a pull environment. It controls the material quantities in production. It defines a loop between demand source and the supply source for recurring replenishment.
In the above statement, it is mentioned that, it is linking the demand source and supply source. In SAP, how we are linking the the demand source and supply source?
While creating the supply area in PK05, we are providing the storage location. Is this supply source or demand source?
In SAP, where we are assigning the another source (supply / demand source)?
Regards
pskHello Mario,
Thank you very much for your detailed explanation on storage bin and container.
1. So, if the storage location is not WM managed, there will not be any storage bin. The storage location itself will act as a storage bin. Am i right?
You said that, Containers are the physical means in which materials are kept in this process. a container usually equals a KANBAN. Normally there are at least two (but can be more) containers in a control cycle.
2. We are using pallets to replanish the supply area storage locations (production store which is near to work center). So in this example, the pallets are called as "containers". Am i right?
Consider the below example:
3. In control cycle i have maintained the number of kanban as 4. As you said above, i need to maintain 4 containers. But i have only one field to maintain the container. How to maintain 4 containers in one field?
Thank you.
psk -
BAPI /FM to create /change KANBAN control cycle
Hi
Is there any BAPI or FM to create or Change control cycle?
Thanks.Check
BAPI - BAPI_KANBANCC_ADDEVENTDRKANBAN
Short Text
Create Event-Driven KANBAN for Control Cycle
Functionality
With this method you can procure a material quantity for a control cycle. To procure this material quantity one or more kanbans are created in the control cycle and set to status EMPTY.
The essential entry parameters are:
o Control cycle (if the function module is called as a method for the object kanban control cycle, this parameter is not available, but given by the object.
o Material quantity
Information about the status change is issued.
COMMIT and ROLLBACK WORK: the function module does not carry out any COMMIT work. Command off. This must be ensured by the initiator after ending the function module. Each time the function module is called, a COMMIT WORK must take place. It is not permitted to call this FM several times and to post the result with a COMMIT WORK. If, during the process,
the FM comes across an error, in some cases the command ROLLBACK WORK wil be carried out. In these cases the kanban is either set to ERROR status, or in the parameter RETURN an error message is given.
Hope this helps.
Regards
Vinayak -
Deletion of KANBAN control cycle
Hi All,
I need to delete a KANBAN control cycle which is the TCODE used for doing so , another problem is that the control cycle is created with the TCODE PK01 and the sypply area is a ware house related one .
Thanks and Regards,
Mallik.Hi,
Delete the Kanban control cycle with the Transaction: PK02.
Control Cycle --> Delete Entry (Shift+F2)
Best Regards,
Siva -
User Exit for PKMC (Kanban Control Cycle)
Dear Gurus,
I need to know if there is a user exit in PKMC (kanban control Cycle) to create a extra tab next to the print control tab in the bottom.
Best Regards,
KumarList of exits available.
Enhancement/ Business Add-in Description
Enhancement
MPKR0001 Customer fields in kanban control cycle
MPKP0002 Customer-Specific Fields Call Interface
MPKP0001 Customer Defined Display in Kanban Board
MPKD0001 Kanban output as EDI
MPKCCY02 Customer Error in SumJC Control Cycle
MPKCCY01 User-Defined Fields in Kanban Control Cycle (PKMC)
MPKC0001 User exit for kanban calculation
MPKB0002 Customer defined display in kanban board
MPKB0001 User's own functions in the Kanban processing
Business Add-in
BADI_PVBE_UPDATE_APO PVB Publish Changes to the APO
MPKC_REQ_SELECTION BAdI for Requirements Selection for Kanban Calculation
PK_CALL_INTERFACE Customer-Specific Fields Call Interface
PK_CCY_SELECTION Selection for Maintaining Control Cycles
PK_REVERSAL BAdI during reversal of Kanban -
KANBAN control cycle quantity changes tracking -reg
Hi,
Which tables and fields are to be used to knwo the changes in the kanban quantities in the control cycle of a part number
for a part number over a period of time what and all changes are done to the kanban quantity we would like to track
how to go about ?
pl guide
regards,
madhu kiranHi,
Try Table PKCH and field PKCMG.This would be your best bet. -
KANBAN control cycle pk01 error
Hi friends,
I am using SAP 5.0 and material is WM activated, getting error while creating control cycle in PK01.
Error -: Storage bin 002 / / does not exist {Message no. PK033}
Note-:it can be solved with PKMC but in SAP 5.0 Pkmc T-code is not available.
Regards
AmitHi,
Check in the material master for the material, whether you have maintained any fixed bin in WM2 for the storage type 150.
Thanks,
JK -
Create KANBAN control cycle (PK01) via LSMW
Hi,
Anybody perofrmed control cycle creation via LSMW using BAPI or IDOC method? I need to know the Business object (BAPI method) or Message type for IDOC menthod in LSMW for PK01 tcode.
Thanks.you should enable the F4 search help in your LSMW.
I have it active and found Idoc PKHD5 -
ABAP report to use in analysis of Kanban Control Cycle
Hi Experts,
I have requirement to develop a new custom report 'Kanban history'.
When someone makes a change to transaction 'PK02', we need to have Kanban History of that change in our new custom report. Also, when someone makes a change to transaction PK13N or PK12N on a kanban correction, we need to capture that history to be able to followup on status changes or kanban corrections made from that screen.
As an example, this kanban history report can be displayed much like the material master history is displayed.
I need your suggestion to achieve this requirement.
Thanks,
LeoHi Leo,
1. Create a Ztable with the fields you want to capture.
2. Find some EXIT's/ BADI or Enhancment points in the t-codes during SAVE.
3. Save ammendments done using the t-code to your Z table .
4. Develop report based on the data you have in your Z table.
I also had a similar requirement to capture the PO ammendment data and display in custome reports
same logic worked
Hope this helps.
Regards
Bikas -
SNC Kanban Issue - Control Cycle Master Data
Hi,
We are testing the SNC Kanban scenario with contracts (PO) between ECC & SNC.
We have created a control cycle for the ECC material and have sent the Master Data to SNC. We are now trying to send over the control cycle info to SNC and are getting hte following message when we run KANBAN_MD_TRANSMIT:
"Kanban control cycle 70666: No address data available; processing terminated"
Any suggestions would be appreciated.
regards.Hi Anjan Bellur
As per the error message, the address details for your supply area are not maintained
Kindly go to the transaction PK05 in r/3 system
For your plant and Production supply area, Shift+F5
Maintain the address details
Then the reported error message will not appear
Best Regards
Vinod -
Change KANBAN Status Sequence in Control Cycle
Hi guys,
Can anyone please detail which are the implications if I should change the status sequence for a control cycle, which is in use now?
Regards,
IleanaHi
In the kanban process the actual sequence is
Wait>Empty>In process > Intransit> Full > In use>Empty.This is complete cycle
If ur present kanban bin status is "In use" then then u changed the sequence in the control cycle.
When ever u trigger the kanban card, then system move to control cycle and checks the kanban sequence by referring the standard sequence it move to next status.
Eg: Ur present sequence is like
Empty>In process> In -transit --> Full --> Empty
Now ur bin status is "Full" then u have changed the sequence in the control cycle.
New sequence is like
"Empty--> In process > Full> In use -->Empty"
Now u triggered the kanban card of " Full" status bin, then system refer first sequence in the control cycle and then standard sequence then status is changing to " In use"
Means when ever u change the sequence in the control cycle system checks the sequence in the control cycle by reference of standard sequence it will changes the bin status.
So if ur bin is in the "In -use " status, then what ever the next status in the sequence is taken when u trigger the kanban signal -
A trigger blocking function for control cycle in Kanban
Hi,
I wantet to change the status in Kanban. I get this error u201CA trigger blocking function was defined for the control cycle in the replenishment strategyu201D. I don't want to set a period of blocking function. how can I deactivate it.
ThanksHi,
Pls. check the following setting :
First in PK13n ( KANBAN Board) check whether X is marked with KANBAN Number e.g. 1X.
If so then replenishment will not be triggered because KANBAN is locked.
To unlock the KANBAN pls do the following :
Go to -
> PKMC ( Control Cycle Maintanance) in Change Mode----> Select Control Cycle -> Go to Display Control Cycle ( Glass Icon)--> on top of details of kanban cycle choose option ---> Display Kanbans ( Spectacle Icon )
Select it and go inside : Inside pop up appearing check first Column : Lkln ( Lock Indicator).
Remove the tick in check box of lock indicator for respective KANBAN for which you want to trigger replenishment.
Pls. try above settings and revert back if still problem persists.
Reward if problem solved.
Regards,
Tejas
Edited by: Tejas Pujara on Aug 1, 2008 12:25 PM -
Control cycle for KANBAN.
I want to cosume componenets using my KANBAN BINS.
I maintained my supplying areas. and when coming to the control cycle. Do I have to maintain control cycle for each component that I use in maufacturing against each supply area? or is it only for FERTSHi,
1. When you tell consume compoenents means you are talking about Goods issue.
2. Kanban needs to be done for a Inhouse prodcued material or externall procured material
3. In both cases it does a Goods receipt and relevant goods issue posting.
4. so if you only need to do consumption it is not possible.
5. Genearlly it can be maitained for the FERT or halbs which has bom, routing releavent master data
6.For the inhouse manufacture kanban below is the highlevel step
7. and wehen you do status cahnges like full to empty a planned order or prod order will be created.
8. when you change status empty to ful then GR will be posted and GI will be done immediatelly ( based on the control cycle)
9. Kindly refer the attached link for further details.
[KANBAN|http://sap-pphelp.blogspot.com/2010/01/kanban-inhouse-production.html]
also let me know if you have any specific querry
Reg
dsk -
Issue during creation of control cycle
Dear Gurus,
During creation of control cycle (LPK1), the fields for source information is not appearing in my system.
I compared control cycle in a different ECC system where source information is appearing.
How can make the screen appear in my ECC system.
Please find the screenshot.
Any pointers will be highly appreciated.
This thread is further to the thread in Production Planning Forum
http://scn.sap.com/thread/3609441
With Regards,
MalayManish,
I do not understand how this going to solve the issue because why we need both KANBAN and WM control cycles for one material withdrawal for production?
Br
KK -
Creation of control cycles for lean WH
Hi All,
Is it possible to create control cycles (backflush) for LWH, if so how?HI ,
There is one more way to create control cycle.
1. PK05 - create supply area ( earlier explained the procedure)
2. PKMC - enter plant - go to change mode ( click on change icon ) - in the right hand window - you can see the create / copy icon.
3.click on create icon
4.select option - classic Kanban or event driven kanban
5.enter material/ plant/ supply area.
6.enter no of kanban / qty.
7.In replenishment strategy - select appropiate option ( in our case it is stock transfer)
8.enter - the tab will change from replenishment strategy to stock transfer.
9.enter storage location.
10.enter destination- storage type- bin
11.enter if any additional data required to enter.
12. save- control cycle will get generated.
thanks
Om
Maybe you are looking for
-
Tables for 2LIS_18_ORDER/2LIS_18_I3HDR .
Hi Xperts, Tables for 2LIS_18_ORDER/2LIS_18_I3HDR is not available in Help.sap.com. So could you please provide me the tables for this data sources? Regards, Sap
-
Can't get sound through headphones
I cannot get sound through earbuds
-
Best practice for navigation menu
I'm using the standard dropdown navigation widget in Muse. For example I have: Top level: Contact Dropdown: 'Fix-my-document' Dropdown: Book appointment My website has been up for about a month, and what I've found (using Google analytics) is that pe
-
No sound on FaceTime! What am I doing wrong?
I can't get sound on FaceTime. They can hear me but I can't hear them. I have sound for videos etc. just no sound on FaceTime .
-
Hi showing conpany code missing in table t43s
hi when i make process open items its showing company code missing table t43s can any give valuable point thanks raju