KDE 4.2 and USB Mass Storage , does not write data until unmounted

Hi,
I have a Nokia phone that I connect for USB mass storage, and KDE 4.2.2 does not seem to write the data to the device until I unmount.
Is there a way to force the write so it happens right away? It's annoying because I can't see any progress when it copies the data at unmount.
Later,
Snorkel

That's kinda the way linux does things, not specifically a KDE issue. It's so that the system only has to write out to the media only once, even if you separately add/delete/move 50 different files.
I think you can run 'sync' and that will flush all the file system buffers to disk.
Last edited by Odysseus (2009-05-01 01:30:59)

Similar Messages

My key board Sound while I am writing and the letter S doeS not write in lower caSe

My key board Sound while I am writing and the letter S doeS not write in lower caSe

PleaSe reply. I am french, the dictation doeS not underStand my accent

PCI Communication Controller and USB Mass Storage Device driver was missing

Hi,
Recently i formated HP Pavilion Slimline 400 PC series and reinstalled with windows 7 32 bit.\
initially i found a lot of driver was missing. i have gone through hp support forums and almost all drivers are running on 64 bit with minimum requirement OS windows 8.1.
i couldn't find it anywhere. under device manager, these two devices are being shown with yellow exclamation
PCI Simple Communication Controller :
PCI\VEN_8086&DEV_8C3A&SUBSYS_2AF7103C&REV_04
PCI\VEN_8086&DEV_8C3A&SUBSYS_2AF7103C
PCI\VEN_8086&DEV_8C3A&CC_078000
PCI\VEN_8086&DEV_8C3A&CC_0780
USB Mass Storage Device :
USB\VID_054C&PID_02A5&REV_0100
USB\VID_054C&PID_02A5
Please kindly provide the link for the drivers, so i can use my PC.
thanks in advance

Hi:
Did you install the USB3 controller driver so the device you installed could work?
https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=21129&lang=eng&ProdId=3467
The USB Mass Storage Device is something you have connected to the PC.
Specifically a Sony® MicroVault USB Flash Drive.
If my suggestion to let windows update find the Intel Management Engine driver, didn't work, see if this driver from Intel works. It also has the hardware ID for that device in the setup information file.
https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=22093&lang=eng

Ovi suite messed my computer and usb mass storage ...

I had lots of problems with my C6 and had to backup it with Ovi suite before sending to nokia service.
Now I have uninstalled Ovi suite and can't connect my phone anymore as a usb mass storage drive. I also found out that while installing Ovi suite, it wasn't the only nokia program that got installed to my hard drive.
How I can not connect my phone again as a mass storage?
Win xp, sp3
And I also WANT EVERY NOKIA APP OFF MY COMPUTER. Why this ain't happening while uninstalling ovi suite (which was the only app that I wanted to install)???

Hi,
I guess the installation of Ovi Suite is corrupted, please follow the steps provided below to assist you in this regard
Step 1
- Go to Add/remove Control Panel
- Click Ovi Suite
- Click Repair.
Once repair is completed then please restart computer and check.
If Step 1 didnt work, then try the below step
Step2
-Go to Add/Remove in Control Panel
- Click Ovi Suite
- Click Uninstall
Also uninstall the following f
- Nokia Connectivity Cable Driver
- PC connectivity Solution
Then right click my computer, click manage.
- Device Manager-Ports- If you find anything by name Nokia please unistall ( Dont remove anything else)
Then reinstall windows Installer from the link provided below
For Windows 7 & Vista
http://msdn.microsoft.com/en-us/library/cc185688(v=vs.85).aspx
For Windows XP
http://www.microsoft.com/downloads/en/details.aspx?FamilyID=5a58b56f-60b6-4412-95b9-54d056d6f9f4&dis...
- Then restart computer.
- Download and install Ovi Suite
- Restart Computer again
- Connect the device, dont open Ovi Suite and wait for all the driver to be loaded by windows.
- Once done then lauch Ovi Suite.
- Check for the issue
Hopefully this helps
Cheers
Show appreciation by clicking the kudos star :-), or gesture by typing thanks

Tecra M10-17U does not write data on DVD disks

Good morning,
I have problem using my DVD recorder.
It doesn't burn, only give-me error.
I 've test with difrent programs and other operating system, and diferente disks.
Thank You.

Did you try to clean the laser lens?
You can do this carefully using a cotton wool tip and alcohol fluid.
But be very careful while doing this
In my case this helped. I had some problems writing the data on different disks and cleaning the lens was the key!

Usb masse storage in solaris 10 problem !!

Hi all
i have srss 3.0 with solaris10-GA, all work well but the usb masse storage
does' nt recognize by srss3.0 are there solution for that problem.
or patch for srss 3.0.
thanks team

Congratulations on your choice of Os ;-)
To solve this problem you can try and create a directory called /rmdisk , then start vold running:
/etc/init.d/volmgt stop
/etc/init.d/volmgt start
if you are lucky your USB flash will show up under /rmdisk/<name> after a few seconds.
If not you should be able to see the flash with cfgadm, which list the status of USB ports (among other things).
Solaris should automatically create a /dev/dsk/ and /dev/rdsk/ entries for your flash memory, if its not automatically mounted by vold, try and stop vold using
/etc/init.d/volmgt stop
Then do a cd /dev/dsk and run an ls -lart, the USB devices should be among the last devices in that list, then mount it using:
mount -F pcfs /dev/dsk/<device> /some/directory
the device should end with s2 or p2, some flash devices might also need :c, aka /dev/dsk/<device>:c, it depends how its configured.
See man mount_pcfs for more information...
Hope this helps a bit (:
//Magnus

How to use cRIO USB mass storage?

Hi,
I am using the NI9215 as an analog input port and want to write the data into an external USB mass storage which is connected in the
cRIo-9012 USB port. I do not have any idea how to write the data into USB mass storage, does anyone can give me some help?

Differences among brands and models are due to the fact that certain devices take greater liberties with the USB mass storage device specification than others. A venerable operating system like Windows (or even Linux) is shot through with workarounds for device- and manufacturer-specific issues that are not present (as much) in VxWorks, which is the OS used on the cRIO-9012. Therefore only devices that adhere very rigorously to the specification are going to work properly.
Unfortunately, degree of adherence to the USB spec is not something that's generally published about a device, nor is there any sort of official certification process. So to some extent it's trial and error. I am working with our support enginners currently to develop a list of devices that NI certifies as interoperable with VxWorks, and also VxWorks is increasing the robustness of their USB support with every release.
EDIT: And the advice about reformatting the device is very sound. The cRIO-9012 does not support the NTFS file system, only FAT 12, 16, and 32. If the USB device is formatted for NTFS, it will not function properly.
Finally, if anyone sees a storage device that fails to work properly despite all these suggestions, please post as much information as possible (model number, manufacturer, capacity). Having this information will allow us to work with the manufacturers of VxWorks to improve USB support.
Message Edited by CharlesC on 02-22-2007 12:12 PM

I have a new mac air 11inches, i tried to download my pictures using my usb mass storage device. how come my mac can't recognize and open my files? pls help...

i have a new mac air 11 inches and i tried to download my pictures using my usb mass storage device. how come my mac is not reading it? pls hel...

What exactly is your 'mass USB device', and how is it formatted? When you connect it to your MBA, does it show up on the desktop?

IPOD seen as two drives(USB Mass Storage & and Dell USB )

My IPOD classic has not worked properly since I updated my OS to Windows XP. At first the IPOD was seen as two different USB controllers (Apple USB Driver, and a USB Mass Storage Device) I've gone through every troubleshooting article on the apple website. After downloading a hotfix, my computer recognizes the IPOD as an IPOD but it doesn't connect to itunes long enough for me to restore it. It automatically disconnects after being plugged into the computer. If anybody can help, please, please please let me know.
Thanks.

I just purchased an ipod classic 120GB and after downloading itunes to the computer I can no longer use my DVD/CD drive as the ipod is using that drive now, which is the E drive on my computer. I noticed that if I uninstall itunes I get to use my DVD/CD drive again. I do not know what next to try either. So my ipod is seen as a mass storage device, I need help too, can anyone help?
zndrsmith

Samsung A900 USB mass storage and Tiger

I just got a Samsung A900 phone, when I connect with USB as mass storage device, the phone is mounted write protected in 10.4.3. In 10.3.9, it mounts as a writeable drive.

Hi there. I just bought a Samsung A900 and figured out how to use the phone as a USB Mass storage device:
My setup is a PowerBook G4 with 10.4.6 all updates (including the latest Security Updates and iLife '06 updates).
1. Plug the USB cable into the phone, and your computer.
2. The phone should say "USB Cable connected" on the main screen. If it doesn't, turn the phone off, and back on again with the cable plugged in.
3. Press the Menu button
4. Go to Tools
5. Go to Mass Storage
6. Select "Connect to PC."
You will not be able to receive phone calls while the phone is in USB Mass Storage mode.
A new volume should appear in the OS X Finder as "Untitled."
You have access to the same folders as with a Bluetooth connection.
Unfortunately, this also means that it is not a solution to get custom ring tones from an MP3 you own.
I tried looking in Terminal for any hidden folders, and I can't find any. I honestly think a firmware update/hack is needed to enable this on the phone.
Hope this helps.
PowerBook G4 1.33 GHz 17" Mac OS X (10.4.4) iPod w/video 60 GB, iSight
PowerBook G4 1.33 GHz 17" Mac OS X (10.4.6) iPod w/video 60 GB, iSight

HT1369 Ipod nano 7th gen, itunes cannot locate device, worked fine 4 16 mths, have reinstalled itunes & usb mass storage, still has !. not teccy and thoughts?

My itunes account cannot identify my device, worked fine until yesterday. Sons computer can locate the same device. Not very tech savvy, but checked device manager and the Mass Storage Device has a yellow ! which updated, re installing etc cannot get rid of. I have reinstalled itunes as well, still does not recognise my device.any assistance is appreciated

Have a look at TS1363: iPod: Appears in Windows but not in iTunes.
You should keeps copies of everything on your iPod in your iTunes library so that it can be reloaded should the need arise. See Recover your iTunes library from your iPod or iOS device for retrieval steps once your device is visible.
tt2

Help my computer does say USB Mass storage device

ok so i can't charge my ipod and the computer doesn't even recognize that i have connect the ipod. so i went here
http://docs.info.apple.com/article.html?artnum=305136
and it told me what to look for so i lookded for it but my computer doesn't say anything like USB Mass Storage Device or Ipod. I was wondering is there any way for me to download USB Mass Storage Device for the ipod.
If so can you help me do it.
Thanx
Ipod Video Windows XP

How about this article?
iTunes for Windows: iTunes 7 doesn't recognize iPod
http://docs.info.apple.com/article.html?artnum=304434
Patrick

USB Mass Storage Device - ?

Shuffle shows up as a USB Mass Storage Device under the drive (USB Port) i plug it into.
It will not take an update or reformat.
Wondering if it is possible that the factory format could be erased and now the unit is just being recognized as a storage device and unable to be used in the manner it was originally intended for...MUSIC.?
What does it mean when you get a message "Media in Drive - Changed" ?
Fixed many other ipods in past but only one shuffle so far....now this one has me going...no clue what else i can do to it.
Any help would be appreciated.

i think it was trying to read the shuffle when i wanted to format and restore.
i never did get it to work.
no way of knowing now..i just got through tearing into this one to make one good shuffle out of the two i was working on.
all was good till i went to put the slide bar on/off switch back on....broke the switch again.
do you have a switch?
thanks

USB Mass Storage Device won't Eject/Unmount

My brother bought a Sanyo ICR-B180NX digital voice recorder last year to use with his iBook. It was working very well up until about August of 2005. At that point, the recorder would mount on the desktop, and he could get all the files off (it records direct to MP3 format rather than WMV, so he can edit his files very easily), but when it came time to eject it, the device icon would disappear and then immediately re-appear on the desktop. The display on the voice recorder remained static at the "Connect" screen.
I believe this happened in conjunction with some sort of OS update, as it was a "sudden" thing. We can't quite recall what happened between the times it worked and the time it stopped working.
I have tried the device on a PC, and it works the way it should, so I don't believe there's anything wrong with it.
Now, I know the system requirements on the website say that you must have Windows, but a statement from a support company (we returned it to the place where we got it, and they sent it out for repairs, and it came back with a letter) states that the device does act as a generic Mass Storage device, and thus may work with most systems.
All my other USB storage devices (ie. SanDisk 12-in-1 card reader, SanDisk Cruzer Titanium 2GB, iPod Photo), and FireWire devices (ie. WiebeTech TrayDock Extreme) work fine and unmount fine.
Does anyone know of any changes to the way Mass Storage devices are ejected in the current iteration of the OS? I haven't had a chance to test the device under an older OS, but will soon.
Alternately, if anyone has any suggestions regarding replacements (not really looking forward to that, given this recorder cost almost $300CAD), let me know. We need a device that can plug in via USB and transfer files to his iBook which he can edit together (he's a newspaper reporter in training, and needs to edit the interviews to take out such things like dead air, etc).
Thanks!
Mike Ma.

Hi
+USB mass storage device. An error occurred during the installation of the device the data is invalid+
This typical error message appears if the installation of external USB devices failed.
Why? This is not easy to say
What you could do firstly is to clean your registry using the freeware software called CCleaner (Google for that).
Install it and clean your OS and the registry entries.
After cleaning access the device manager and remove all USB root hubs and all USB Host controllers from the device list and reboot the notebook.
New reboot should cause a new installation of USB drivers.
Finally try to connect and try to install your external USB devices again.

Windows 7 64-bit not loading USB mass storage driver

I have a rather strange problem with my Windows 7 Ultimate 64-bit. Everything seems to work fine except for USB mass storage devices. I have USB keyboard, mouse and even a USB audio (wireless headset) all working fine on the computer. But
any USB external drive, thumdrive or USB card reader with flash cards inserted into the USB port of my computer won't work.
Windows keeps reporting that it is unable to find the driver. When I go into the Device Manager console and choose to manually update the driver, then point it to the C:\Windows (with search for sub-directories enabled), it detects the USB Mass Storage
driver but complains that it is unable to load it. The exact message is this: Windows found driver software for your device but encountered error while attempting to install it. USB Mass Storage Device. The system cannot find the file
specified.
This happens to ALL USB Mass storage device, and it doesn't matter which port I plug the device into.
Here's the weird thing, I have VMware Workstation installed on this computer and if I power on a VM that runs Windows 7 32-bit as the Guest OS and connect the USB storage devices to the guest OS via VMware Workstation, the USB storage devices work!
So it would appear that the USB ports are functioning properly but for some reasons, my Windows 64-bit is unable to load the driver.
Any idea how to fix this besides a "nuke it from orbit" and format/reinstall Windows?
Thanks.

I'm very excited to finally have a solution for this problem. Thank You Balaji for figuring this out. I've been struggling with this for a number of years, and had only one USB Hard Drive that worked. I too have VMware workstation, and had the missing files
in "c:\windows\inf." I can say with certainty that I did not delete the files from that folder, but something is common in both of our situations. Maybe it has to do with VMware, and some of it's updates over the years. I'm also using nCompute to share out
a networked desktop via the wire.
One more thing worthy of mention is this machine was an update from Windows Vista, and the USB hard drive that worked was configured back than. So although I could never add another HD, at least I had the one.
Now with having copied over the files, I can plugin other USB enclosures with different drives and they too are working.
Like you mentioned, it was always possible to use USB devices within my Virtual Machines, so it was clear that the USB ports were functional. I actually got the files from a clean Windows 7 VM, copying out the \windows\inf folder and doing a compare between
the the real one and the virtual one. I found the two missing files you mentioned, along with 8 others. I went ahead and included them all in your fix.
It worked, Amazing. Thanks again. :O)

KDE 4.2 and USB Mass Storage , does not write data until unmounted

Similar Messages

Maybe you are looking for