Keep alive a SIP Trunk?

Hi!
I'm trying to register a SIP Trunk to a SIP server. The trunk registration is done, but not keep alive. The trunk register with SIP server when an outgoing call starts, but when this call ends, the SIP trunk closes the connection with SIP server. Then, the
outgoing calls work OK, but the incoming calls doesn't work because the SIP Trunk is unregistered while no active outgoing calls.
Then, can i keep alive the SIP Trunk registration with SIP Server?
Thanks!!!

You need to talk to the SIP provider and get them enable OPTIONS on the SIP Trunk and enable OPTIONS on the PSTN Gateway. Check the registration interval of the SIP trunk on the Gateway and try increasing it to a higher value.
http://thamaraw.com

Similar Messages

  • E51 SIP and NAT keep alive

    I am brad new to the Nokia E seris. I have set up a SIP peer but the problem is trying to call the phne using sip as there seems to be no setting o configure NAT keep alive
    Cananyone help or point me?
    Thanks
    Dave

    I Googled up the following:
    http://lists.apple.com/archives/Macnetworkprog/2006/Jul/msg00040.html
    I am having this issue:
    http://discussions.apple.com/message.jspa?messageID=7256265#7256265
    Are all these things the same issue?
    My ISP "tells me" that they will not allow more than one IP address per account. I have a basic cable modem i.e. not a router. Its a D-Link DCM-202. I have been told to try a level-2 switch but I can't see how that will work. As far as I can see the DCM-202 cable modem is bridging to my AEBS so that is allocated the WAN IP address by the ISP's DHCP server. Does this sound right?
    I'd like to create an actual DMZ but since my cable modem only has one port I can't see how I can do that unless I use 2 routers. If I try this I am expecting that I'd have complicated port forwarding configurations no?

  • Which UK SIP Trunk Provider?

    Hi,
    I'm looking for a UK SIP trunk service provider. I dont wish to be tied to a specific ISP. Does a list of confirmed working providers exist?
    Best regards,
    Paul.

    Afternoon Peter,
    Of course, it's a pleasure:
    Description:  Voiptalk
    Proxy:  voiptalk.org
    Require Registration: Ticked
    Uses SIP Remote-Party-ID:  Unticked
    Outbound Proxy:  nat.voiptalk.org
    Only Allow Calls To:  (Leave this box blank)
    Call Capacity: 2
    Prefix dialed numbers with "+44": Unticked
    Company Name: (Leave this box blank)
    Account ID:  Enter your Account ID in this box, e.g. 8442855xx (where the xx are also numbers)
    Authentication ID: 
    Account ID:  Enter your Account ID in this box, e.g. 8442855xx (where the xx are also numbers this is the same number as entered in the Account ID box above)
    Password:  Enter your voiptalk password for the account number entered above
    SRV Record Lookup:  Unticked
    SRV Auto Prefix:  Unticked
    NAT Mapping: Unticked
    Send Nat Keep Alive: Unticked
    Local SIP Port: 5060
    It's pretty straigh forward but let me know if you have any problems and we'll see if I can get a number to you to give me a call and I'll try talk you through it.
    Regards,
    Paul.

  • SIP trunk incoming and outgoing calls issue

    Hi Everyone,
    We recently installad a SIP trunk and terminated on CUBE and CUCM but we have issues on incoming and outgoing calls, When someone dial in from outside he keeps listening the dailing ring even after we pick up the phone and at the end the callers time exipres and call gets disconnected.
    For Dailing out, the dialed number rings and caller hear the dailing ring as well but if someone pick the phone it apprears that call is connected but no audio in it, dead air.
    Our call flow is as 
    IP Phones => CUCM --->SIPTRUNK--->CUBE=>SIPTRUNK=>SP
    I have attached the config for CUBE and debug ccsip messages output for both incoming and outgoing calls.
    Please if some help in sorting out this issue, Thanks in Advance
    Tasneem

    Inbound call>>>>
    The reason you are experiencing this is that your CUBE is requesting PRACK and your provider is not responding to it..
    Here we have your cube sending 180 ringing with "Require 100rel"..This was sent several times and your ITSP didnt respond probably because they do not support 100rel...(It is Huwaei after all, they do what they like)
    Sent:
    SIP/2.0 180 Ringing
    Via: SIP/2.0/UDP 10.205.20.50:5060;branch=z9hG4bKkpw18wp35hfw2c23h51ww6a8aT19871
    From: ;tag=sbc080552fph4hp-CC-25
    To: ;tag=256F3440-12C
    Date: Thu, 16 Jan 2014 13:31:34 GMT
    Call-ID: isbc6818c4kfhaa4ca1k5f8k1awsh52f1ccw@SoftX3000
    CSeq: 1 INVITE
    Require: 100rel
    RSeq: 2507
    Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
    Allow-Events: telephone-event
    Remote-Party-ID: "TEST STC" ;party=called;screen=yes;privacy=off
    Contact:
    Record-Route:
    Server: Cisco-SIPGateway/IOS-15.2.4.M2
    Content-Length: 0
    AFter the CUBE didnt get any response, it then replied with Gateway Timeout...
    Jan 16 13:31:54.550: //31880/5A4406E48184/SIP/Msg/ccsipDisplayMsg:
    Sent:
    SIP/2.0 504 Gateway Timeout
    Via: SIP/2.0/UDP 10.205.20.50:5060;branch=z9hG4bKkpw18wp35hfw2c23h51ww6a8aT19871
    From: ;tag=sbc080552fph4hp-CC-25
    To: ;tag=256F3440-12C
    Call-ID: isbc6818c4kfhaa4ca1k5f8k1awsh52f1ccw@SoftX3000
    CSeq: 1 INVITE
    Reason: Q.850;cause=102
    Content-Length: 0
    I suggest you disable this parameter..and test again
    voice service voip
    sip
    rel1xx disable
    Please rate all useful posts
    "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

  • Forwarding with SIP Trunking and Retaining CID

    We are using SIP trunking to get to the PSTN and CUCM 7.1.  The SIP provider only permits calls originating from their own DIDs.
    So how can we allow our users to forward all calls to say their cell phone.  AND when a call comes in we want them to be able to see the original caller ID. Is it possible?  What is the mojo?  Thanks!

    Hi,
    for the SIP trunks there are no limits from the system. Check this out: https://supportforums.cisco.com/message/3795863#3795863
    If you have different voice codecs for your phones and the trunk you need DSP ressources for transcoding.
    As I know the UC520 have a PVDM2-64 with 4 DSP chips. You can use the DSP calculator from cisco to find out how many DSPs you need. But keep in mind that conferencing and transcoding can't share a DSP processor.
    For example 1 DSP for conferencing and 3 for transcoding.
    best regards
    Christian

  • Unity Connection not passing CallerID to CUCM over SIP Trunk

    I'm trying to get CallerID working for Unity Connection Device Notification (and it seems everything else), however, when I run UC Remote Port Status Monitor and the Call-Out goes to CUCM for the Device Notification, no caller ID is presented to the CUCM SIP trunk.
    06:06:02, New Call, CalledId=,  RedirectingId=,  Origin=16,  Reason=1024,  CallGuid=, 
    CallerName=,  LastRedirectingId=,  LastRedirectingReason=1024,  PortDisplayName=LFC_CUCM-1-134,
    [Origin=Unknown],[Reason=Unknown]
    06:06:02,
    Dialing '99254753'
    06:06:32, Idle
    06:06:33, Idle
    Therefore, the out-going call to the PRI PSTN is:
    10:59:01.005: ISDN Se0/0/0:23 Q931: TX -> SETUP pd = 8  callref = 0x5B03
            Sending Complete
            Bearer Capability i = 0x8090A2
                    Standard = CCITT
                    Transfer Capability = Speech
                    Transfer Mode = Circuit
                    Transfer Rate = 64 kbit/s
            Channel ID i = 0xA98397
                    Exclusive, Channel 23
            Calling Party Number i = 0x0081, N/A
                    Plan:Unknown, Type:Unknown
            Called Party Number i = 0xC1, '9254753'
                    Plan:ISDN, Type:Subscriber(local)
    *Dec  6 10:59:01.513: ISDN Se0/0/0:23 Q931: RX <- CALL_PR
    I've looked through my SIP trunk on the CUCM side and for Inbound Calls, Connected Line ID and Presentation Name are set to "allowed" or "default" doesn't make a difference. RTMT Port Status also shows no "caller", so I'm thinking there is some way to set or allow the calling number on the Unity Connection (8.5) side.
    Oddly enough, I also noticed that in Unity Connection> Telephony Integrations > Port Group, if I change the Contact Line Name from nothing to "Unity" (or whatever), the Q931 debug outbound doesn't show ANY "Calling Party Numer - = XXXXX" and the carrier throws out the BTN as the ANI.
    10:46:00.837: ISDN Se0/0/0:23 Q931: TX -> SETUP pd = 8  callref = 0x5AFF
            Sending Complete
            Bearer Capability i = 0x8090A2
                    Standard = CCITT
                    Transfer Capability = Speech
                    Transfer Mode = Circuit
                    Transfer Rate = 64 kbit/s
            Channel ID i = 0xA98397
                    Exclusive, Channel 23
            Called Party Number i = 0xC1, '9254753'
                    Plan:ISDN, Type:Subscriber(local)
    Any ideas on where/how CallerID comes from, on Unity Connection with a SIP integration?
    THANKS!!
    Mike.

    I did not- my work around has been to put in a name for Contact Line Name under Port Group Basics Switch configuration in Unity Connection- this for some reason keeps CUCM from sending ANI TYPE/PLAN information in the Q931 message, and my carrier then sends a default ANI of the circuit's BTN. When I have time, I'll open up a TAC ticket.
    Mike.

  • NexVortex SIP trunk and UC500 default timeout settings?

    Hey guys,
    I'm doing a little SIP trunk testing to determine a good provider for my customer base, and had some general questions as I can't seem to get outgoing or incoming phone calls to work at all.
    To keep things simple, I'm using an 8user UC540W with 3 IP phones - a 525G, a 524G, and a 7937 conference phone.  I have a static IP on the UC540, have run through the telephony wizard and everything seems to be working on the LAN/PBX side of things.  The big difference, and the major variable that we are working with (I believe), is that we're working with Satellite internet connectivity rather than terrestrial Internet connectivity.  This is an Enterprise satellite connection, and we have run voice over the connection without problems, but this is our first attempts at SIP trunking from a UC500.  Due to the latency involved inherent in satellite (ping times around 550-700ms), I believe that either UC540 or NexVortex server/switch is timing out.  Is there any way to determine what the default setting is for a SIP acknowledgement on the UC540 and change this if it is too small?
    Here is what I have found, if it is helpful:
    Outgoing calls:
    1. The SIP provider, NexVortex, says that they are seeing an invite from the UC540, but not on port 5060.  On the two calls that we tested, it first saw an invite on 63452, and then on 51677.  Is there any reason why this would not be sent out on 5060?
    Incomign calls:
    1. On incoming calls, Nexvortex is routing the calls to the proper IP, but is then receiving an "error 500 reason Q850" from the UC540.  What does this error mean?
    I am also attaching my config in the event that it helps.  When I look at the SIP trunk status in CCA, it does not show that registration is working, so I assume that's a good place to start.
    Lastly, the guys over at NexVortex don't seem to run across the UC500 very often.  If anybody has setup their UC500 to work with NexVortex and wouldn't mind posting a screenshot from CCA (feel free to remove usernames and passwords), I'd appreciate it.  I'm not certain that I have all of the information in the right places.
    Thanks,
    Seth

    Hi Steven,
    Thanks for the continued help.
    I was able to make the changes in the config.  Here are snapshots from the current config:
    dial-peer voice 1000 voip
    description ** Incoming call from SIP trunk (Generic SIP Trunk Provider) **
    voice-class codec 1
    voice-class sip dtmf-relay force rtp-nte
    session protocol sipv2
    session target sip-server
    incoming called-number .%
    dtmf-relay rtp-nte
    ip qos dscp cs5 media
    ip qos dscp cs4 signaling
    no vad
    dial-peer voice 3000 voip
    description IncomingSIP
    translation-profile incoming IncomingSIP_Called_4
    voice-class codec 1
    voice-class sip dtmf-relay force rtp-nte
    session protocol sipv2
    session target sip-server
    incoming called-number 14068906254$
    dtmf-relay rtp-nte
    ip qos dscp cs5 media
    ip qos dscp cs4 signaling
    no vad
    dial-peer voice 3001 voip
    description IncomingSIP2
    translation-profile incoming IncomingSIP2_Called_5
    voice-class codec 1
    voice-class sip dtmf-relay force rtp-nte
    session protocol sipv2
    session target sip-server
    incoming called-number 1406890624[2-3]$
    dtmf-relay rtp-nte
    ip qos dscp cs5 media
    ip qos dscp cs4 signaling
    no vad
    dial-peer voice 3002 voip
    incoming called-number 14068906254$
    no dial-peer outbound status-check pots
    sip-ua
    authentication username nomadgcs password 7 *removed*
    no remote-party-id
    retry invite 2
    retry register 10
    timers connect 100
    registrar ipv4:66.23.129.253:5060 expires 3600
    sip-server ipv4:66.23.129.253:5060
    connection-reuse
    host-registrar
    We are calling from within the 406 area code, so when we dial the number with the leading 406, we get a message saying "You don't need the area code" from the telephone company.  When we dial this from a cell, we get the following:
    1. 4068906254 - "All circuits are busy, please try your call again..."
    2. 8906254 - rings once, then no sound, then disconnects after about 10 seconds.
    I don't know if this would factor in at all, but our NexVortex account is setup to deliver 14068906254 to the UC500, but would NexVortex deliver the entire string of characters if it is only receiving 4068906254 or 8906254?
    Thanks,
    Seth

  • HFM Web Sever Configuration--Keep Alive and Session Time Out Optimal Config

    We recently implemented an HFM 9.3.1 environment. We are using Windows 2003 Enterprise SP2 servers with IIS6. We have two HFM Web servers connecting to an application cluster with two application servers in the cluster. We were getting some errors when trying to unlock HFM cells in Workspace, but we were able to perform the functions fine on the application using the WIN32 client.
    I opened a ticket with support and they recommended modifying the subcontext.properties file located in %HYPERION_HOME%\deployments\WebLogic9\servers\Workspace\webapps\workspace\conf. They recommended changing the following settings:
    #KeepAliveInterval=30
    #SessionTimeout=60
    From what I understand, these settings are for the communication between the HFM Web Servers and the application cluster servers. I'm wondering how changing these settings may affect our environment. Are there negative effects and/or trade-offs for changing these settings? Is there a recommended threshold or maximum value?

    Hi Dinesh,
    This cannot be achieved without development enhancements to some standard SAP framework component, to introduce a "keep-alive" concept. If you are using a CMS for CTI or email integration, you need to ensure it supports keeping the communications session alive also.
    Sincerely,
    Glenn
    Glenn Abel
    Covington Creative
    www.covingtoncreative.com

  • Issue with instant ringback when using sip trunk to SP

    Hi all,
    We use CUCM 8.0.2.
    We have a SIP trunk to a SP connected via one of our Cisco 2911 routers configured as a CUBE.
    Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M3, RELEASE SOFTWARE (fc2)
    c2900-universalk9-mz.SPA.150-1.M3.bin
    Cisco CISCO2911/K9 (revision 1.0)
    Technology Package License Information for Module:'c2900'
    Technology Technology-package
                      Current       Type
    ipbase        ipbasek9      Permanent
    security      securityk9    Permanent
    uc              uck9            Permanent
    data           None            None
    We also have several ISDN lines that run out via various Cisco routers configured as H323 gateways.
    We use 7945 and CIPC for our phones.
    We're having an issue with calls going via the SIP trunk where we hear ringing instantly after dialling - but before the actual device at the other end starts ringing (considerable difference).
    Using the SIP trunk: If I make a call to my mobile phone - I hear ringing instantly - about 3 rings before my mobile phone actually starts ringing - undesireable.
    Using H323 gateway: If I make a call to my mobile phone - I hear silence for a bit - then ringing when the mobile starts ringing - desired.
    Using SIP trunk: If I make a call to a landline that is ready - it rings instantly for at least 1 ring - before the actual phone I'm calling starts ringing - undesireable.
    Using H323 gateway: There is a momentary pause before hearing ringing on my phone and the phone I dialled - desired.
    Using SIP trunk: If I make a call to a landline that is off-hook (with no call-waiting/etc.) - it rings once and then returns the busy signal (the worst issue) - undesireable.
    Using H323 gateway: There is a momentary pause before hearing busy signal - desired.
    Phone to phone internally (same network): Operates as expected (instantly rings locally and on the phone I'm calling). Between phones that utilise the SIP trunk and phones that utilise the H323 gateways within the same network - communication is instant and as expected.
    Any ideas why this happens and how to stop it?
    I want it to not ring until the situation is known and that it can provide the appropriate feedback (ringing/busy/etc.).
    Some possibly relevant config (note that there is a known bug with this IOS that meant I had to declare the codec in each dial-peer as the voice class would not work):
    voice service voip
    address-hiding
    mode border-element
    allow-connections sip to sip
    sip
      bind control source-interface GigabitEthernet0/0
      bind media source-interface GigabitEthernet0/0
      header-passing error-passthru
      early-offer forced
      midcall-signaling passthru
    interface GigabitEthernet0/0
    ip address x.x.x.x 255.255.255.252
    ip access-group acl.SIP-IN in
    no ip redirects
    no ip unreachables
    ip verify unicast reverse-path
    ip virtual-reassembly
    duplex full
    speed 100
    no cdp enable
    gateway
    timer receive-rtp 1200
    sip-ua
    connection-reuse
    gatekeeper
    shutdown
    dial-peer voice 1 voip
    description *** INBOUND CALLS FROM CARRIER ***
    translation-profile incoming SIPTRUNK-INCOMING
    session protocol sipv2
    incoming called-number #blah blah#
    dtmf-relay rtp-nte
    codec g711alaw
    ip qos dscp cs5 media
    no vad
    dial-peer voice 61 voip
    description **** WA, SA AND NT NUMBERS ****
    destination-pattern 0[8]........
    session protocol sipv2
    session target ipv4:<MY SP's SIP SERVER>
    incoming called-number 0[8]........
    dtmf-relay rtp-nte
    codec g711alaw
    ip qos dscp cs5 media
    no vad
    dial-peer voice 81 voip
    description **** MOBILE NUMBERS ****
    destination-pattern 0[4]........
    session protocol sipv2
    session target ipv4:<MY SP's SIP SERVER>
    incoming called-number 0[4]........
    dtmf-relay rtp-nte
    codec g711alaw
    ip qos dscp cs5 media
    no vad
    dial-peer voice 500 voip
    description *** INBOUND SIP TRUNK TO CUCM PUB ***
    translation-profile outgoing SIPTRUNK-CALLING-ADD-0
    preference 1
    destination-pattern 5[12]..
    session protocol sipv2
    session target ipv4:<OUR CUCM PUBLISHER IP>
    dtmf-relay rtp-nte
    codec g711alaw
    ip qos dscp cs5 media
    no vad
    Any help or a point in the right direction would be greatly appreciated.
    Cheers,
    Brett

    I ended up resolving this issue as follows:
    In CUCM, under Device > Device Settings > SIP Profile.
    I modifed the profile relevant to my SIP trunk, under the "Trunk Specific Configuration", I set "SIP Rel1XX Options" from "Disabled" to "Send PRACK if 1xx Contains SDP".
    Now, I get the expected delay before hearing ringback.
    Solved!

  • SIP Trunk - No voice with Single Number Reach

    Hi Community.
    I setup SIP Trunk with the CCA. Everything is working Call In and Call Out. Call Forward and so on.
    But with Single Number reach is something wrong. The mobile phone is ringing and I can get the call, but I hear not any voice.
    Can someone please help me out? Below the config.
    version 15.1
    parser config cache interface
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    service internal
    service compress-config
    service sequence-numbers
    dot11 ssid cisco-data
     vlan 1
     authentication open
    dot11 ssid cisco-voice
     vlan 100
     authentication open
    ip source-route
    ip cef
    ip dhcp relay information trust-all
    ip dhcp excluded-address 10.1.1.1 10.1.1.9
    ip dhcp excluded-address 10.1.1.241 10.1.1.255
    ip dhcp pool phone
     network 10.1.1.0 255.255.255.0
     default-router 10.1.1.1
     option 150 ip 10.1.1.1
    ip domain name site1.365873.trk.ipvoip.ch
    ip name-server 8.8.8.8
    ip inspect WAAS flush-timeout 10
    ip inspect name SDM_LOW dns
    ip inspect name SDM_LOW ftp
    ip inspect name SDM_LOW h323
    ip inspect name SDM_LOW https
    ip inspect name SDM_LOW icmp
    ip inspect name SDM_LOW imap
    ip inspect name SDM_LOW pop3
    ip inspect name SDM_LOW netshow
    ip inspect name SDM_LOW rcmd
    ip inspect name SDM_LOW realaudio
    ip inspect name SDM_LOW rtsp
    ip inspect name SDM_LOW esmtp
    ip inspect name SDM_LOW sqlnet
    ip inspect name SDM_LOW streamworks
    ip inspect name SDM_LOW tftp
    ip inspect name SDM_LOW tcp router-traffic
    ip inspect name SDM_LOW udp router-traffic
    ip inspect name SDM_LOW vdolive
    no ipv6 cef
    multilink bundle-name authenticated
    stcapp ccm-group 1
    stcapp
    isdn switch-type basic-net3
    voice call send-alert
    voice rtp send-recv
    voice service voip
     ip address trusted list
      ipv4 0.0.0.0 0.0.0.0
     allow-connections h323 to h323
     allow-connections h323 to sip
     allow-connections sip to h323
     allow-connections sip to sip
     supplementary-service h450.12
     no supplementary-service sip refer
     fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
     sip
      registrar server expires max 3600 min 3600
      localhost dns:site1.365873.trk.ipvoip.ch
      no update-callerid
    voice class codec 1
     codec preference 1 g711alaw
    voice register global
     mode cme
     source-address 10.1.1.1 port 5060
     load 9971 sip9971.9-2-2
     load 9951 sip9951.9-2-2
     load 8961 sip8961.9-2-2
     timezone 23
    voice source-group CCA_SIP_SOURCE_GROUP_CUE_CME
     access-list 2
     translation-profile incoming SIP_Incoming
    voice source-group CCA_SIP_SOURCE_GROUP_EXTERNAL
     access-list 3
    voice translation-rule 9
     rule 1 /0041449475090/ /90/
     rule 2 /0041449475091/ /91/
     rule 3 /0041449475092/ /92/
     rule 4 /0041449475093/ /93/
     rule 5 /0041449475094/ /94/
     rule 6 /0041449475095/ /95/
     rule 7 /0041449475096/ /96/
     rule 8 /0041449475097/ /97/
     rule 9 /0041449475098/ /98/
     rule 10 /0041449475099/ /99/
    voice translation-rule 410
     rule 1 /^0\(.*\)/ /\1/
     rule 15 /^..$/ /0041449475090/
    voice translation-rule 411
     rule 1 /^0\(.*\)/ /ABCD0\1/
    voice translation-rule 412
     rule 1 /^ABCD\(.*\)/ /\1/
    voice translation-rule 422
     rule 15 /^ABCD\(.*\)/ /\1/
    voice translation-rule 1000
     rule 1 /.*/ //
    voice translation-rule 1111
     rule 1 /^9\([1-9]\)$/ /004144947509\1/
     rule 15 /^..$/ /0041449475090/
    voice translation-rule 1112
     rule 1 /^0/ //
    voice translation-rule 2000
     rule 1 /0041449475098/ /98/
    voice translation-rule 2001
     rule 1 /0041449475097/ /97/
    voice translation-rule 2002
     rule 1 /^6/ //
    voice translation-rule 2222
    voice translation-profile AA_Profile
     translate called 2001
    voice translation-profile CALLER_ID_TRANSLATION_PROFILE
     translate calling 1111
    voice translation-profile CallBlocking
     translate called 2222
    voice translation-profile OUTGOING_TRANSLATION_PROFILE
     translate called 1112
    voice translation-profile PSTN_CallForwarding
     translate redirect-target 410
     translate redirect-called 410
    voice translation-profile PSTN_Outgoing
     translate calling 1111
     translate called 1112
     translate redirect-target 410
     translate redirect-called 410
    voice translation-profile SIP_Called_9
     translate calling 3265
     translate called 9
    voice translation-profile SIP_Incoming
     translate called 411
    voice translation-profile SIP_Passthrough
     translate called 412
    voice translation-profile SIP_Passthrough_CallBlocking
     translate called 422
    voice translation-profile VM_Profile
     translate called 2000
    voice translation-profile XFER_TO_VM_PROFILE
     translate redirect-called 2002
    voice translation-profile nondialable
     translate called 1000
    voice-card 0
     dspfarm
     dsp services dspfarm
    fax interface-type fax-mail
    license udi pid UC540W-BRI-K9 sn FGL163220SL
    archive
     log config
      logging enable
      logging size 600
      hidekeys
    username admin privilege 15 secret xxx
    username xxx password 0 ""
    username xxx password 0 ""
    ip tftp source-interface Loopback0
    bridge irb
    interface Loopback0
     description $FW_INSIDE$
     ip address 10.1.10.2 255.255.255.252
     ip access-group 101 in
     ip nat inside
     ip virtual-reassembly in
    interface FastEthernet0/0
     description $FW_OUTSIDE$
     no ip address
     ip inspect SDM_LOW out
     ip virtual-reassembly in
     ip verify unicast reverse-path
     load-interval 30
     shutdown
     duplex auto
     speed auto
    interface Integrated-Service-Engine0/0
     description cue is initialized with default IMAP group
     ip unnumbered Loopback0
     ip nat inside
     ip virtual-reassembly in
     service-module ip address 10.1.10.1 255.255.255.252
     service-module ip default-gateway 10.1.10.2
    interface FastEthernet0/1/0
     no ip address
     macro description cisco-desktop
     spanning-tree portfast
    interface FastEthernet0/1/1
     switchport voice vlan 100
     no ip address
     macro description cisco-phone
     spanning-tree portfast
    interface FastEthernet0/1/2
     switchport voice vlan 100
     no ip address
     macro description cisco-phone
     spanning-tree portfast
    interface FastEthernet0/1/3
     switchport voice vlan 100
     no ip address
     macro description cisco-phone
     spanning-tree portfast
    interface FastEthernet0/1/4
     switchport voice vlan 100
     no ip address
     macro description cisco-phone
     spanning-tree portfast
    interface FastEthernet0/1/5
     switchport voice vlan 100
     no ip address
     macro description cisco-phone
     spanning-tree portfast
    interface FastEthernet0/1/6
     switchport voice vlan 100
     no ip address
     macro description cisco-phone
     spanning-tree portfast
    interface FastEthernet0/1/7
     switchport voice vlan 100
     no ip address
     macro description cisco-phone
     spanning-tree portfast
    interface FastEthernet0/1/8
     no ip address
     macro description cisco-desktop
     spanning-tree portfast
    interface BRI0/1/0
     no ip address
     isdn switch-type basic-net3
     isdn point-to-point-setup
     isdn incoming-voice voice
     isdn sending-complete
     isdn static-tei 0
    interface BRI0/1/1
     no ip address
     shutdown
     isdn switch-type basic-net3
     isdn point-to-point-setup
     isdn incoming-voice voice
     isdn sending-complete
     isdn static-tei 0
    interface Dot11Radio0/5/0
     no ip address
     ssid cisco-data
     ssid cisco-voice
     speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
     station-role root
     antenna receive right
     antenna transmit right
    interface Dot11Radio0/5/0.1
     encapsulation dot1Q 1 native
     bridge-group 1
     bridge-group 1 subscriber-loop-control
     bridge-group 1 spanning-disabled
     bridge-group 1 block-unknown-source
     no bridge-group 1 source-learning
     no bridge-group 1 unicast-flooding
    interface Dot11Radio0/5/0.100
     encapsulation dot1Q 100
     bridge-group 100
     bridge-group 100 subscriber-loop-control
     bridge-group 100 spanning-disabled
     bridge-group 100 block-unknown-source
     no bridge-group 100 source-learning
     no bridge-group 100 unicast-flooding
    interface Vlan1
     no ip address
     bridge-group 1
     bridge-group 1 spanning-disabled
    interface Vlan100
     no ip address
     bridge-group 100
     bridge-group 100 spanning-disabled
    interface BVI1
     description $FW_INSIDE$
     ip address 192.168.10.2 255.255.255.0
     ip access-group 102 in
     ip nat inside
     ip virtual-reassembly in
    interface BVI100
     description $FW_INSIDE$
     ip address 10.1.1.1 255.255.255.0
     ip access-group 103 in
     ip nat inside
     ip virtual-reassembly in
    ip forward-protocol nd
    ip http server
    ip http authentication local
    ip http secure-server
    ip http path flash:/gui
    ip dns server
    ip nat inside source list 1 interface FastEthernet0/0 overload
    ip route 0.0.0.0 0.0.0.0 192.168.10.1
    ip route 10.1.10.1 255.255.255.255 Integrated-Service-Engine0/0
    access-list 1 remark SDM_ACL Category=2
    access-list 1 permit 10.1.1.0 0.0.0.255
    access-list 1 permit 192.168.10.0 0.0.0.255
    access-list 1 permit 10.1.10.0 0.0.0.3
    access-list 2 remark CCA_SIP_SOURCE_GROUP_ACL_INTERNAL
    access-list 2 remark SDM_ACL Category=1
    access-list 2 permit 192.168.10.2
    access-list 2 permit 10.1.10.0 0.0.0.3
    access-list 2 permit 192.168.10.0 0.0.0.255
    access-list 2 permit 10.1.1.0 0.0.0.255
    access-list 3 remark CCA_SIP_SOURCE_GROUP_ACL_EXTERNAL
    access-list 3 remark SDM_ACL Category=1
    access-list 3 permit 212.147.47.216
    access-list 3 deny   any
    access-list 100 remark auto generated by SDM firewall configuration
    access-list 100 remark SDM_ACL Category=1
    access-list 100 deny   ip 192.168.10.0 0.0.0.255 any
    access-list 100 deny   ip host 255.255.255.255 any
    access-list 100 deny   ip 127.0.0.0 0.255.255.255 any
    access-list 100 permit ip any any
    access-list 101 remark auto generated by SDM firewall configuration##NO_ACES_8##
    access-list 101 remark SDM_ACL Category=1
    access-list 101 permit tcp 10.1.1.0 0.0.0.255 eq 2000 any
    access-list 101 permit udp 10.1.1.0 0.0.0.255 eq 2000 any
    access-list 101 deny   ip 10.1.1.0 0.0.0.255 any
    access-list 101 deny   ip 192.168.10.0 0.0.0.255 any
    access-list 101 deny   ip 192.168.1.0 0.0.0.255 any
    access-list 101 deny   ip host 255.255.255.255 any
    access-list 101 deny   ip 127.0.0.0 0.255.255.255 any
    access-list 101 permit ip any any
    access-list 102 remark auto generated by SDM firewall configuration##NO_ACES_6##
    access-list 102 remark SDM_ACL Category=1
    access-list 102 deny   ip 10.1.10.0 0.0.0.3 any
    access-list 102 deny   ip 10.1.1.0 0.0.0.255 any
    access-list 102 deny   ip 192.168.1.0 0.0.0.255 any
    access-list 102 deny   ip host 255.255.255.255 any
    access-list 102 deny   ip 127.0.0.0 0.255.255.255 any
    access-list 102 permit ip any any
    access-list 103 remark auto generated by SDM firewall configuration##NO_ACES_8##
    access-list 103 remark SDM_ACL Category=1
    access-list 103 permit tcp 10.1.10.0 0.0.0.3 any eq 2000
    access-list 103 permit udp 10.1.10.0 0.0.0.3 any eq 2000
    access-list 103 deny   ip 10.1.10.0 0.0.0.3 any
    access-list 103 deny   ip 192.168.10.0 0.0.0.255 any
    access-list 103 deny   ip 192.168.1.0 0.0.0.255 any
    access-list 103 deny   ip host 255.255.255.255 any
    access-list 103 deny   ip 127.0.0.0 0.255.255.255 any
    access-list 103 permit ip any any
    access-list 104 remark auto generated by SDM firewall configuration##NO_ACES_14##
    access-list 104 remark SDM_ACL Category=1
    access-list 104 deny   ip 10.1.10.0 0.0.0.3 any
    access-list 104 deny   ip 10.1.1.0 0.0.0.255 any
    access-list 104 permit ip any any
    access-list 104 permit udp host 8.8.8.8 eq domain any
    access-list 104 permit icmp any any echo-reply
    access-list 104 permit icmp any any time-exceeded
    access-list 104 permit icmp any any unreachable
    access-list 104 deny   ip 10.0.0.0 0.255.255.255 any
    access-list 104 deny   ip 172.16.0.0 0.15.255.255 any
    access-list 104 deny   ip 192.168.0.0 0.0.255.255 any
    access-list 104 deny   ip 127.0.0.0 0.255.255.255 any
    access-list 104 deny   ip host 255.255.255.255 any
    access-list 104 deny   ip host 0.0.0.0 any
    access-list 104 deny   ip any any
    control-plane
    bridge 1 route ip
    bridge 100 route ip
    voice-port 0/0/0
     cptone CH
     station-id name FAX
     station-id number 99
     caller-id enable
    voice-port 0/0/1
     cptone CH
     shutdown
     caller-id enable
    voice-port 0/0/2
     cptone CH
     shutdown
     caller-id enable
    voice-port 0/0/3
     cptone CH
     shutdown
     caller-id enable
    voice-port 0/1/0
     compand-type a-law
     cptone CH
     bearer-cap Speech
    voice-port 0/1/1
     compand-type a-law
     cptone CH
     bearer-cap Speech
    voice-port 0/4/0
     auto-cut-through
     signal immediate
     input gain auto-control -15
     description Music On Hold Port
    sccp local Loopback0
    sccp ccm 10.1.1.1 identifier 1 version 4.0
    sccp
    sccp ccm group 1
     associate ccm 1 priority 1
     associate profile 2 register mtpa4934c6ee4e0
    dspfarm profile 2 transcode
     description CCA transcoding for SIP Trunk VTX
     codec g711ulaw
     codec g711alaw
     codec g729ar8
     codec g729abr8
     maximum sessions 10
     associate application SCCP
    dial-peer cor custom
     name internal
     name local
     name local-plus
     name international
     name national
     name national-plus
     name emergency
     name toll-free
    dial-peer cor list call-internal
     member internal
    dial-peer cor list call-local
     member local
    dial-peer cor list call-local-plus
     member local-plus
    dial-peer cor list call-national
     member national
    dial-peer cor list call-national-plus
     member national-plus
    dial-peer cor list call-international
     member international
    dial-peer cor list call-emergency
     member emergency
    dial-peer cor list call-toll-free
     member toll-free
    dial-peer cor list user-internal
     member internal
     member emergency
    dial-peer cor list user-local
     member internal
     member local
     member emergency
     member toll-free
    dial-peer cor list user-local-plus
     member internal
     member local
     member local-plus
     member emergency
     member toll-free
    dial-peer cor list user-national
     member internal
     member local
     member local-plus
     member national
     member emergency
     member toll-free
    dial-peer cor list user-national-plus
     member internal
     member local
     member local-plus
     member national
     member national-plus
     member emergency
     member toll-free
    dial-peer cor list user-international
     member internal
     member local
     member local-plus
     member international
     member national
     member national-plus
     member emergency
     member toll-free
    dial-peer voice 1 pots
     destination-pattern 99
     port 0/0/0
     no sip-register
    dial-peer voice 2 pots
     port 0/0/1
     no sip-register
    dial-peer voice 3 pots
     port 0/0/2
     no sip-register
    dial-peer voice 4 pots
     port 0/0/3
     no sip-register
    dial-peer voice 5 pots
     description ** MOH Port **
     destination-pattern ABC
     port 0/4/0
     no sip-register
    dial-peer voice 6 pots
     description tcatch all dial peer for BRI/PRIv
     translation-profile incoming nondialable
     incoming called-number .%
     direct-inward-dial
    dial-peer voice 50 pots
     description ** incoming dial peer **
     incoming called-number ^AAAA$
     direct-inward-dial
     port 0/1/0
    dial-peer voice 51 pots
     description ** incoming dial peer **
     incoming called-number ^AAAA$
     direct-inward-dial
     port 0/1/1
    dial-peer voice 2000 voip
     description ** cue voicemail pilot number **
     translation-profile outgoing XFER_TO_VM_PROFILE
     destination-pattern 98
     b2bua
     session protocol sipv2
     session target ipv4:10.1.10.1
     voice-class sip outbound-proxy ipv4:10.1.10.1
     dtmf-relay rtp-nte
     codec g711ulaw
     no vad
    dial-peer voice 2001 voip
     description ** cue auto attendant number **
     translation-profile outgoing PSTN_CallForwarding
     destination-pattern 97
     b2bua
     session protocol sipv2
     session target ipv4:10.1.10.1
     voice-class sip outbound-proxy ipv4:10.1.10.1
     dtmf-relay rtp-nte
     codec g711ulaw
     no vad
    dial-peer voice 2012 voip
     description ** cue prompt manager number **
     translation-profile outgoing PSTN_CallForwarding
     destination-pattern 96
     b2bua
     session protocol sipv2
     session target ipv4:10.1.10.1
     voice-class sip outbound-proxy ipv4:10.1.10.1
     dtmf-relay rtp-nte
     codec g711ulaw
     no vad
    dial-peer voice 1000 voip
     permission term
     description ** Incoming call from SIP trunk (VTX) **
     session protocol sipv2
     session target sip-server
     incoming called-number .%
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     fax rate 14400
     fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1001 voip
     corlist outgoing call-local
     description ** star code to SIP trunk (VTX) **
     destination-pattern *..
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     fax rate 14400
     fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1003 voip
     description ** Passthrough Inbound Calls for PSTN from CUE **
     translation-profile incoming SIP_Passthrough
     b2bua
     session protocol sipv2
     session target ipv4:10.1.10.1
     incoming called-number ABCDT
     dtmf-relay rtp-nte
     codec g711ulaw
     no vad
    dial-peer voice 1005 voip
     description ** Passthrough Inbound Calls for MWI from CUE **
     b2bua
     session protocol sipv2
     session target ipv4:10.1.10.1
     incoming called-number A80T
     dtmf-relay rtp-nte
     codec g711ulaw
     no vad
    dial-peer voice 1009 voip
     description ** Passthrough Inbound Calls for Internal Extensions from CUE **
     b2bua
     session protocol sipv2
     session target ipv4:10.1.10.1
     incoming called-number ^..$
     dtmf-relay rtp-nte
     codec g711ulaw
     no vad
    dial-peer voice 1033 voip
     corlist outgoing call-local
     description **CCA*Switzerland*Short Code Services**
     translation-profile outgoing PSTN_Outgoing
     preference 1
     destination-pattern 0187
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1042 voip
     corlist outgoing call-emergency
     description **CCA*Switzerland*Ambulance / Poisioning**
     translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
     preference 1
     destination-pattern 0014[45]
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1041 voip
     corlist outgoing call-emergency
     description **CCA*Switzerland*REGA Air Rescue**
     translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
     preference 1
     destination-pattern 00333333333
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1025 voip
     corlist outgoing call-national
     description **CCA*Switzerland*National Destination Numbers**
     translation-profile outgoing PSTN_Outgoing
     preference 1
     destination-pattern 00[789]1.......
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1020 voip
     corlist outgoing call-national
     description **CCA*Switzerland*Regional Announcement VM**
     translation-profile outgoing PSTN_Outgoing
     preference 1
     destination-pattern 01600
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1040 voip
     corlist outgoing call-emergency
     description **CCA*Switzerland*REGA Air Rescue**
     translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
     preference 1
     destination-pattern 000333333333
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1043 voip
     corlist outgoing call-emergency
     description **CCA*Switzerland*Ambulance / Poisioning**
     translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
     preference 1
     destination-pattern 014[45]
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1035 voip
     corlist outgoing call-national
     description **CCA*Switzerland*Mobile Numbers**
     translation-profile outgoing PSTN_Outgoing
     preference 1
     destination-pattern 007[46789].......
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1024 voip
     corlist outgoing call-national-plus
     description **CCA*Switzerland*Personal Numbering**
     translation-profile outgoing PSTN_Outgoing
     preference 1
     destination-pattern 00878......
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1029 voip
     corlist outgoing call-national
     description **CCA*Switzerland*Voicemail Access**
     translation-profile outgoing PSTN_Outgoing
     preference 1
     destination-pattern 00860.........
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1036 voip
     corlist outgoing call-national
     description **CCA*Switzerland*VPN Access**
     translation-profile outgoing PSTN_Outgoing
     preference 1
     destination-pattern 00869.............
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1027 voip
     corlist outgoing call-national-plus
     description **CCA*Switzerland*Premium Rate (Business)**
     translation-profile outgoing PSTN_Outgoing
     preference 1
     destination-pattern 00900......
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1026 voip
     corlist outgoing call-national
     description **CCA*Switzerland*Test Numbers**
     translation-profile outgoing PSTN_Outgoing
     preference 1
     destination-pattern 00868T
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1034 voip
     corlist outgoing call-national-plus
     description **CCA*Switzerland*Shared Cost numbers**
     translation-profile outgoing PSTN_Outgoing
     preference 1
     destination-pattern 0084[0248]......
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1038 voip
     corlist outgoing call-emergency
     description **CCA*Switzerland*Emergency**
     translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
     preference 1
     destination-pattern 0011[278]
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1037 voip
     corlist outgoing call-toll-free
     description **CCA*Switzerland*Toll Free Numbers**
     translation-profile outgoing PSTN_Outgoing
     preference 1
     destination-pattern 00800......
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1039 voip
     corlist outgoing call-emergency
     description **CCA*Switzerland*Emergency**
     translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
     preference 1
     destination-pattern 011[278]
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1032 voip
     corlist outgoing call-national
     description **CCA*Switzerland*National Destination Numbers**
     translation-profile outgoing PSTN_Outgoing
     preference 1
     destination-pattern 00[23456]........
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1023 voip
     corlist outgoing call-international
     description **CCA*Switzerland*International Calls**
     translation-profile outgoing PSTN_Outgoing
     preference 1
     destination-pattern 000T
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1031 voip
     description **CCA*Switzerland*Premium Rate (Social)**
     translation-profile outgoing PSTN_Outgoing
     preference 1
     destination-pattern 0090[16]......
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1030 voip
     corlist outgoing call-national
     description **CCA*Switzerland*Short Code**
     translation-profile outgoing PSTN_Outgoing
     preference 1
     destination-pattern 014[0357]
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1045 voip
     corlist outgoing call-emergency
     description **CCA*Switzerland*REGA/Glaciers Air Rescue**
     translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
     preference 1
     destination-pattern 0141[45]
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1028 voip
     corlist outgoing call-national-plus
     description **CCA*Switzerland*Directory Enquiries**
     translation-profile outgoing PSTN_Outgoing
     preference 1
     destination-pattern 018[15].
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1021 voip
     corlist outgoing call-national
     description **CCA*Switzerland*Short Code**
     translation-profile outgoing PSTN_Outgoing
     preference 1
     destination-pattern 011[45].
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1022 voip
     corlist outgoing call-national
     description **CCA*Switzerland*Short Code Services**
     translation-profile outgoing PSTN_Outgoing
     preference 1
     destination-pattern 01[67].
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 1044 voip
     corlist outgoing call-emergency
     description **CCA*Switzerland*REGA/Glaciers Air Rescue**
     translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
     preference 1
     destination-pattern 00141[45]
     session protocol sipv2
     session target sip-server
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    dial-peer voice 2002 voip
     description ** cue voicemail PSTN number **
     translation-profile outgoing VM_Profile
     destination-pattern xxx$
     b2bua
     session protocol sipv2
     session target ipv4:10.1.10.1
     voice-class sip outbound-proxy ipv4:10.1.10.1
     dtmf-relay rtp-nte
     codec g711ulaw
     no vad
    dial-peer voice 2003 voip
     description ** cue auto attendant PSTN number **
     translation-profile outgoing AA_Profile
     destination-pattern xxx$
     b2bua
     session protocol sipv2
     session target ipv4:10.1.10.1
     voice-class sip outbound-proxy ipv4:10.1.10.1
     dtmf-relay rtp-nte
     codec g711ulaw
     no vad
    dial-peer voice 1110 pots
     preference 9
     destination-pattern xxx
     port 0/0/0
     no sip-register
    dial-peer voice 3006 voip
     description SIP
     translation-profile incoming SIP_Called_9
     session protocol sipv2
     session target sip-server
     incoming called-number xxx.
     voice-class codec 1
     voice-class sip dtmf-relay force rtp-nte
     dtmf-relay rtp-nte
     ip qos dscp cs5 media
     ip qos dscp cs4 signaling
     no vad
    no dial-peer outbound status-check pots
    sip-ua
     keepalive target dns:site1.365873.trk.ipvoip.ch
     authentication username xxx password 7 xxx
     no remote-party-id
     retry invite 2
     retry register 10
     timers connect 100
     timers keepalive active 100
     registrar dns:site1.365873.trk.ipvoip.ch expires 3600
     sip-server dns:site1.365873.trk.ipvoip.ch
     host-registrar
    telephony-service
     sdspfarm units 5
     sdspfarm transcode sessions 10
     sdspfarm tag 2 mtpa4934c6ee4e0
     video
     fxo hook-flash
     max-ephones 40
     max-dn 300
     ip source-address 10.1.1.1 port 2000
     auto assign 1 to 1 type bri
     calling-number initiator
     service phone videoCapability 1
     service phone ehookenable 1
     service phone ehookEnable 1
     service dnis overlay
     service dnis dir-lookup
     service dss
     timeouts interdigit 5
     system message SwissT.Net
     url services http://10.1.10.1/voiceview/common/login.do
     url authentication http://10.1.10.1/voiceview/authentication/authenticate.do
     cnf-file location flash:
     cnf-file perphone
     user-locale U4 load CME-locale-de_DE-German-8.1.2.2.tar
     network-locale U4
     load 521G-524G cp524g-8-1-17
     load 525G spa525g-7-5-4
     load 501G spa50x-30x-7-5-2b
     load 502G spa50x-30x-7-5-2b
     load 504G spa50x-30x-7-5-2b
     load 508G spa50x-30x-7-5-2b
     load 509G spa50x-30x-7-5-2b
     load 525G2 spa525g-7-5-4
     load 301 spa50x-30x-7-5-2b
     load 303 spa50x-30x-7-5-2b
     time-zone 23
     time-format 24
     date-format dd-mm-yy
     keepalive 30 auxiliary 4
     voicemail 98
     max-conferences 8 gain -6
     call-forward pattern .T
     call-forward system redirecting-expanded
     hunt-group logout HLog
     moh flash:/media/music-on-hold.au
     multicast moh 239.10.16.16 port 2000
     web admin system name cisco secret 5 xxx
     dn-webedit
     time-webedit
     transfer-system full-consult dss
     transfer-pattern .T
     transfer-pattern 0.T
     transfer-pattern 6.. blind
     secondary-dialtone 0
     night-service day Sun 17:00 09:00
     night-service day Mon 17:00 09:00
     night-service day Tue 17:00 09:00
     night-service day Wed 17:00 09:00
     night-service day Thu 17:00 09:00
     night-service day Fri 17:00 09:00
     night-service day Sat 17:00 09:00
     fac standard
     create cnf-files version-stamp Jan 01 2002 00:00:00
    ephone-template  1
     url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
     service phone webAccess 0
     softkeys remote-in-use  Newcall
     softkeys idle  Redial Pickup Mobility Newcall Cfwdall Gpickup Dnd Login
     softkeys seized  Cfwdall Endcall Redial Pickup Gpickup Callback
     softkeys connected  Hold Endcall Trnsfer Mobility TrnsfVM Confrn Acct Park
     button-layout 7931 2
    ephone-template  15
     url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
     softkeys remote-in-use  Newcall
     softkeys idle  Redial Newcall Mobility Cfwdall Pickup Gpickup Dnd Login
     softkeys seized  Cfwdall Endcall Redial Pickup Gpickup Callback
     softkeys connected  Hold Endcall Mobility Trnsfer TrnsfVM Confrn Acct Park
     button-layout 7931 2
    ephone-template  16
     url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
     softkeys remote-in-use  Newcall
     softkeys idle  Redial Newcall Mobility Cfwdall Pickup Gpickup Dnd Login
     softkeys seized  Cfwdall Endcall Redial Pickup Gpickup Callback
     softkeys connected  Hold Endcall Mobility Trnsfer TrnsfVM Confrn Acct Park
    ephone-template  17
     url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
     softkeys remote-in-use  CBarge Newcall
     softkeys idle  Redial Newcall Mobility Cfwdall Pickup Gpickup Dnd Login
     softkeys seized  Cfwdall Endcall Redial Pickup Gpickup Callback
     softkeys connected  Hold Endcall Mobility Trnsfer TrnsfVM Confrn Acct Park
    ephone-template  18
     url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
     softkeys remote-in-use  CBarge Newcall
     softkeys idle  Redial Newcall Mobility Cfwdall Pickup Gpickup Dnd Login
     softkeys seized  Cfwdall Endcall Redial Pickup Gpickup Callback
     softkeys connected  Hold Endcall Mobility Trnsfer TrnsfVM Confrn Acct Park
     button-layout 7931 2
    ephone-dn  9
     number BCD no-reg primary
     description MoH
     moh out-call ABC
    ephone-dn  292
     number xxx
     description SIP Main Number registration
     preference 10
    ephone-dn  293  dual-line
     number 90 secondary xxx no-reg both
     label Zentrale
     description 90
     name Zentrale
     call-forward busy 98
     call-forward noan 98 timeout 20
    ephone-dn  294  dual-line
     number 94 secondary xxx no-reg both
     label LL
     description Lehrling Lehrnende
     name Lehrling Lehrnende
     mobility
     snr xxx delay 1 timeout 30 cfwd-noan 98
     snr ring-stop
     call-forward busy 98
     call-forward noan 98 timeout 20
    ephone-dn  295  dual-line
     number 93 secondary xxx no-reg both
     label CM
     description
     name
     snr xxx delay 1 timeout 30 cfwd-noan 98
     snr ring-stop
     call-forward busy 98
     call-forward noan 98 timeout 10
    ephone-dn  296  dual-line
     number 92 secondary xxx no-reg both
     label EE
     description
     name
     mobility
     call-forward busy 98
     call-forward noan 98 timeout 20
    ephone-dn  297  dual-line
     number 91 secondary xxx no-reg both
     label RS
     description
     name
     mobility
     snr xxx delay 1 timeout 30 cfwd-noan 98
     snr ring-stop
     call-forward busy 98
     call-forward noan 98 timeout 10
    ephone-dn  298
     number 6.. no-reg primary
     description ***CCA XFER TO VM EXTENSION***
     call-forward all 98
    ephone-dn  299
     number A801.. no-reg primary
     mwi off
    ephone-dn  300
     number A800.. no-reg primary
     mwi on
    ephone  1
     device-security-mode none
     mac-address A44C.11A0.B648
     ephone-template 1
     max-calls-per-button 2
     username "xxx" password xxx
     type 525G2
     button  1:296 2:293 3m297 4m295
     button  5m294
    ephone  2
     device-security-mode none
     mac-address A44C.11A0.B566
     ephone-template 1
     max-calls-per-button 2
     username "xxx" password xxx
     type 525G2
     button  1:297 2:293 3m296 4m295
     button  5m294
    ephone  3
     device-security-mode none
     mac-address A44C.11A0.B5C4
     ephone-template 1
     max-calls-per-button 2
     username "xxx" password xxx
     type 525G2
     button  1:295 2:293 3m297 4m296
     button  5m294
    ephone  4
     device-security-mode none
     mac-address A44C.11A0.B67A
     ephone-template 1
     max-calls-per-button 2
     username "xxx" password xxx
     type 525G2
     button  1:294 2:293 3m297 4m296
     button  5m295
    alias exec cca_voice_mode PBX
    alias exec cca_vm_notification schedule from_time=00 to_time=24
    alias exec clid-ALL_BRI ;1:0-4;1:0-9;1:0-9;1:1-9
    alias exec clid-SIP ;1:1-9;1:1-9;1:1-9
    banner login ^CCisco Configuration Assistant. Version: 3.2 (3). Fri Jul 04 13:18:33 CEST 2014^C
    line con 0
     no modem enable
    line aux 0
    line 2
     no activation-character
     no exec
     transport preferred none
     transport input all
    line vty 0 4
     transport preferred none
     transport input all
    line vty 5 100
     transport preferred none
     transport input all
    ntp master
    ntp server 91.240.0.5 prefer
    en

    Hi Patrick
    I am working on this one as well. I have a UC560 with SIP Trunk provider Les.NET.
    It was working fine until a few weeks ago when something changed on the provider end and broke it. My hunch it is something to do with the SIP REFER.
    http://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-communications-manager-express/91535-cme-sip-trunking-config.html
    Here is an excerpt from the above page:
    Call Transfer
    When a call comes in on an SIP trunk to an SCCP Phone or CUE AutoAttendant (AA) and is transferred, the CME by default will send a SIP REFER message to the SP proxy. Most SP Proxy Servers do not support the REFER method. This needs to be configured in order to force the CME to hairpin the call:
    Router(config)#voice service voip
    Router(conf-voi-serv)#no supplementary-service sip refer
    Figure 3 shows the behavior of the CME system with the REFER method disabled.

  • Unable to place call on calls on hold - SIP Trunk from CUCM to CUBE and from CUBE to ISTP

    Hi Cisco Community,
    I have a SIP Trunk setup between the CUCM and CUBE and another SIP Dial Peers from the CUBE to the ITSP. All incoming/outgoing calls, DTMF-Relay works well except one thing which is the ability to hold the call.
    On the SIP Trunk from the CUCM to the CUBE, I did not select “MTP” because when I do so, I am forced to select my preferred MTP codec which when selected G.729/G.729a, all my outgoing calls goes out using G.729r8. This codec works well for most of the calls until the ITSP replies back with G.729br8. When this condition occur, my call simply fails (this is very intermittent and only some random numbers).
    That said, I have some issues with DTMF Relay when I select MTP on the SIP Trunk. DTMF Relay only works if the call is G.729r8 all the way from the CUCM to the ITSP. If the ITSP replies back with G.729br8, the call might established but will simply be “voice-only”.
    The current setup is no MTP is selected and everything is working perfectly. I am happy with that until I place a call on hold, which when I do so, the call immediately terminate. Could you please help me understand why?
    I have all media resources configured such as G.729r8 MTP, G.729br8 MTP, G.711u MTP, Transcoding with all codecs, etc. All MRG and MRGL are configured on all devices and SIP Trunks.
    Below is an example of a call that is connected with the current setup:
    Note:
    IP: 10.18.81.2 (CUBE)
    IP: 10.18.81.11 (CUCM SUB)
    IP: 10.111.111.254 (ITSP SBC)
    PM-HO-VG-01#
    PM-HO-VG-01#
    Nov 30 11:44:29.938: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Received: 
    INVITE sip:[email protected]:5060 SIP/2.0
    Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e72063a5aba5d
    From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
    To: <sip:[email protected]>
    Date: Sun, 30 Nov 2014 11:44:29 GMT
    Call-ID: [email protected]
    Supported: timer,resource-priority,replaces
    Min-SE:  1800
    User-Agent: Cisco-CUCM9.1
    Allow: INVITE, OPTIONS, INFO, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY
    CSeq: 101 INVITE
    Expires: 180
    Allow-Events: presence, kpml
    Supported: X-cisco-srtp-fallback,X-cisco-original-called
    Call-Info: <sip:10.18.81.11:5060>;method="NOTIFY;Event=telephone-event;Duration=500"
    Cisco-Guid: 1020645888-0000065536-0000124117-0189862410
    Session-Expires:  1800
    Contact: <sip:[email protected]:5060>
    Max-Forwards: 70
    Content-Length: 0
    Nov 30 11:44:29.942: //64510/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Sent: 
    SIP/2.0 100 Trying
    Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e72063a5aba5d
    From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
    To: <sip:[email protected]>
    Date: Sun, 30 Nov 2014 11:44:29 GMT
    Call-ID: [email protected]
    CSeq: 101 INVITE
    Allow-Events: telephone-event
    Server: Cisco-SIPGateway/IOS-15.2.4.M5
    Content-Length: 0
    Nov 30 11:44:29.946: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Sent: 
    INVITE sip:[email protected]:5060 SIP/2.0
    Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3EC72218
    From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
    To: <sip:[email protected]>
    Date: Sun, 30 Nov 2014 11:44:29 GMT
    Call-ID: [email protected]
    Supported: 100rel,timer,resource-priority,replaces,sdp-anat
    Min-SE:  1800
    Cisco-Guid: 1020645888-0000065536-0000124117-0189862410
    User-Agent: Cisco-SIPGateway/IOS-15.2.4.M5
    Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
    CSeq: 101 INVITE
    Timestamp: 1417347869
    Contact: <sip:[email protected]:5060>
    Call-Info: <sip:10.18.81.2:5060>;method="NOTIFY;Event=telephone-event;Duration=2000"
    Expires: 180
    Allow-Events: telephone-event
    Max-Forwards: 69
    Session-Expires:  1800
    Content-Type: application/sdp
    Content-Disposition: session;handling=required
    Content-Length: 301
    v=0
    o=CiscoSystemsSIP-GW-UserAgent 7676 6958 IN IP4 10.18.81.2
    s=SIP Call
    c=I
    PM-HO-VG-01#N IP4 10.18.81.2
    t=0 0
    m=audio 22256 RTP/AVP 18 0 8 101
    c=IN IP4 10.18.81.2
    a=rtpmap:18 G729/8000
    a=fmtp:18 annexb=yes
    a=rtpmap:0 PCMU/8000
    a=rtpmap:8 PCMA/8000
    a=rtpmap:101 telephone-event/8000
    a=fmtp:101 0-16
    Nov 30 11:44:29.950: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Received: 
    SIP/2.0 100 Trying
    Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3EC72218
    From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
    To: <sip:[email protected]>
    Call-ID: [email protected]
    CSeq: 101 INVITE
    Timestamp: 1417347869
    Nov 30 11:44:30.658: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Received: 
    SIP/2.0 180 Session Progress
    Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3EC72218
    From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
    To: <sip:[email protected]>;tag=71913148-1417348035284
    Call-ID: [email protected]
    CSeq: 101 INVITE
    Timestamp: 1417347869
    Supported: 
    Contact: <sip:[email protected]:5060;transport=udp>
    Session: Media
    Allow: ACK,BYE,CANCEL,INFO,INVITE,OPTIONS,PRACK,REFER,NOTIFY,UPDATE
    X-BroadWorks-Correlation-Info: bbf94839-a234-4237-95e6-a7037322f0f4
    Content-Type: application/sdp
    Content-Length: 355
    v=0
    o=BroadWorks 316169737 1 IN IP4 10.111.111.254
    s=-
    c=IN IP4 10.111.111.254
    t=0 0
    m=audio 20074 RTP/AVP 18 101 100
    a=rtpmap:101 telephone-event/8000
    a=fmtp:101 0-15
    a=rtpmap:100 X-NSE/8000
    a=fmtp:100 200-202
    a=X-sqn:0
    a=X-cap: 1 audio RTP/AVP 100
    a=X-cpar: a=rtpmap:100 X-NSE/8000
    a=X-cpar: a=fmtp:100 200-202
    a=X-cap: 2 image udptl t38
    Nov 30 11:44:30.662: //64510/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Sent: 
    SIP/2.0 183 Session Progress
    Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e72063a5aba5d
    From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
    To: <sip:[email protected]>;tag=3C365010-1E42
    Date: Sun, 30 Nov 2014 11:44:29 GMT
    Call-ID: [email protected]
    CSeq: 101 INVITE
    Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
    Allow-Events: telephone-event
    Contact: <sip:[email protected]:5060>
    Supported: sdp-anat
    Server: Cisco-SIPGateway/IOS-15.2.4.M5
    Content-Type: application/sdp
    Content-Disposition: session;handling=required
    Content-Length: 289
    v=0
    o=CiscoSystemsSIP-GW-UserAgent 7965 2747 IN IP4 10.18.81.2
    s=SIP Call
    c=IN IP4 10.18.81.2
    t=0 0
    m=audio 22350 RTP/AVP 18 101 19
    c=IN IP4 10.18.81.2
    a=rtpmap:18 G729/8000
    a=fmtp:18 annexb=yes
    a=rtpmap:101 telephone-event/8000
    a=fmtp:101 0-15
    a=rtpmap:19 CN/8000
    a=ptime:20
    Nov 30 11:44:31.226: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Received: 
    SIP/2.0 180 Session Progress
    Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3EC72218
    From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
    To: <sip:[email protected]>;tag=71913148-1417348035284
    Call-ID: [email protected]
    CSeq: 101 INVITE
    Timestamp: 1417347869
    Supported: 
    Contact: <sip:[email protected]:5060;transport=udp>
    Session: Media
    Allow: ACK,BYE,CANCEL,INFO,INVITE,OPTIONS,PRACK,REFER,NOTIFY,UPDATE
    X-BroadWorks-Correlation-Info: bbf9
    PM-HO-VG-01#4839-a234-4237-95e6-a7037322f0f4
    Content-Type: application/sdp
    Content-Length: 355
    v=0
    o=BroadWorks 316169737 1 IN IP4 10.111.111.254
    s=-
    c=IN IP4 10.111.111.254
    t=0 0
    m=audio 20074 RTP/AVP 18 101 100
    a=rtpmap:101 telephone-event/8000
    a=fmtp:101 0-15
    a=rtpmap:100 X-NSE/8000
    a=fmtp:100 200-202
    a=X-sqn:0
    a=X-cap: 1 audio RTP/AVP 100
    a=X-cpar: a=rtpmap:100 X-NSE/8000
    a=X-cpar: a=fmtp:100 200-202
    a=X-cap: 2 image udptl t38
    Nov 30 11:44:31.630: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Received: 
    SIP/2.0 200 OK
    Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3EC72218
    From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
    To: <sip:[email protected]>;tag=71913148-1417348035284
    Call-ID: [email protected]
    CSeq: 101 INVITE
    Timestamp: 1417347869
    Supported: 
    Contact: <sip:[email protected]:5060;transport=udp>
    Allow: ACK,BYE,CANCEL,INFO,INVITE,OPTIONS,PRACK,REFER,NOTIFY,UPDATE
    Accept: application/media_control+xml,application/sdp,application/xml
    X-BroadWorks-Correlation-Info: bbf94839-a234-4237-95e6-a7037322f0f4
    Content-Type: application/sdp
    Content-Length: 355
    v=0
    o=BroadWorks 316169737 1 IN IP4 10.111.111.254
    s=-
    c=IN IP4 10.111.111.254
    t=0 0
    m=audio 20074 RTP/AVP 18 101 100
    a=rtpmap:101 telephone-event/8000
    a=fmtp:101 0-15
    a=rtpmap:100 X-NSE/8000
    a=fmtp:100 200-202
    a=X-sqn:0
    a=X-cap: 1 audio RTP/AVP 100
    a=X-cpar: a=rtpmap:100 X-NSE/8000
    a=X-cpar: a=fmtp:100 200-202
    a=X-cap: 2 image udptl t38
    Nov 30 11:44:31.630: //64511/3CD5D2000001/SIP/Call/sipSPICallInfo: 
    The Call Setup Information is:
    Call Control Block (CCB) : 0x0x3D7B1458
    State of The Call        : STATE_ACTIVE
    TCP Sockets Used         : NO
    Calling Number           : 27218091323
    Called Number            : 0862000000
    Source IP Address (Sig  ): 10.18.81.2
    Destn SIP Req Addr:Port  : 10.111.111.254:5060
    Destn SIP Resp Addr:Port : 10.111.111.254:5060
    Destination Name         : 10.111.111.254
    Nov 30 11:44:31.630: //64511/3CD5D2000001/SIP/Call/sipSPIMediaCallInfo: 
    Number of Media Streams: 1
    Media Stream             : 1
    Negotiated Codec         : g729br8
    Negotiated Codec Bytes   : 20
    Nego. Codec payload      : 18 (tx), 18 (rx)
    Negotiated Dtmf-relay    : 6
    Dtmf-relay Payload       : 101 (tx), 101 (rx)
    Source IP Address (Media): 10.18.81.2
    Source IP Port    (Media): 22256
    Destn  IP Address (Media): 10.111.111.254
    Destn  IP Port    (Media): 20074
    Orig Destn IP Address:Port (Media): [ - ]:0
    Nov 30 11:44:31.630: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Sent: 
    ACK sip:[email protected]:5060;transport=udp SIP/2.0
    Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3EC81D00
    From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
    To: <sip:[email protected]>;tag=71913148-1417348035284
    Date: Sun, 30 Nov 2014 11:44:29 GMT
    Call-ID: [email protected]
    Max-Forwards: 70
    CSeq: 101 ACK
    Allow-Events: telephone-event
    Content-Length: 0
    Nov 30 11:44:31.634: //64510/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Sent: 
    SIP/2.0 200 OK
    Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e72063a5aba5d
    From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
    To: <sip:[email protected]>;tag=3C365010-1E42
    Date: Sun, 30 Nov 2014 11:44:29 GMT
    Call-ID: [email protected]
    CSeq: 101 INVITE
    Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
    Allow-Events: telephone-event
    Contact: <sip:[email protected]:5060>
    Supported: replaces
    Supported: sdp-anat
    Server: Cisco-SIPGateway/IOS-15.2.4.M5
    Supported: timer
    Content-Type: application/sdp
    Content-Disposition: session;handling=required
    Content-Length: 289
    v=0
    o=CiscoSystemsSIP-GW-UserAgent 7965 2747 IN IP4 10.18.81.2
    s=SIP Call
    c=IN IP4 10.18.81.2
    t=0 0
    m=audio 22350 RTP/AVP 18 101 19
    c=IN IP4 10.18.81.2
    a=rtpmap:18 G729/8000
    a=fmtp:18 annexb=yes
    a=rtpmap:101 telephone-event/8000
    a=fmtp:101 0-15
    a=rtpmap:19 CN/8000
    a=ptime:20
    Nov 30 11:44:31.726: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Received: 
    ACK sip:[email protected]:5060 SIP/2.0
    Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e72075e3a02c1
    From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
    To: <sip:[email protected]>;tag=3C365010-1E42
    Date: Sun, 30 Nov 2014 11:44:29 GMT
    Call-ID: [email protected]
    Max-Forwards: 70
    CSeq: 101 ACK
    Allow-Events: presence, kpml
    Content-Type: application/sdp
    Content-Length: 236
    v=0
    o=CiscoSystemsCCM-SIP 9082578 1 IN IP4 10.18.81.11
    s=SIP Call
    c=IN IP4 10.18.80.40
    b=TIAS:8000
    b=AS:8
    t=0 0
    m=audio 21928 RTP/AVP 18 101
    a=rtpmap:18 G729/8000
    a=ptime:20
    a=rtpmap:101 telephone-event/8000
    a=fmtp:101 0-15
    Nov 30 11:44:31.730: //64510/3CD5D2000001/SIP/Call/sipSPICallInfo: 
    The Call Setup Information is:
    Call Control Block (CCB) : 0x0x3D816D70
    State of The Call        : STATE_ACTIVE
    TCP Sockets Used         : NO
    Calling Number           : 0218091323
    Called Number            : 0862000000
    Source IP Address (Sig  ): 10.18.81.2
    Destn SIP Req Addr:Port  : 10.18.81.11:5060
    Destn SIP Resp Addr:Port : 10.18.81.11:5060
    Destination Name         : 10.18.81.11
    Nov 30 11:44:31.730: //64510/3CD5D2000001/SIP/Call/sipSPIMediaCallInfo: 
    Number of Media Streams: 1
    Media Stream             : 1
    Negotiated Codec         : g729br8
    Negotiated Codec Bytes   : 20
    Nego. Codec payload      : 18 (tx), 18 (rx)
    Negotiated Dtmf-relay    : 6
    Dtmf-relay Payload       : 101 (tx), 101 (rx)
    Source IP Address (Media): 10.18.81.2
    Source IP Port    (Media): 22350
    Destn  IP Address (Media): 10.18.80.40
    Destn  IP Port    (Media): 21928
    Orig Destn IP Address:Port (Media): [ - ]:0
    Nov 30 11:44:31.730: //64510/3CD5D2000001/SIP/Call/sipSPICallInfo: 
    The Call Setup Information is:
    Call Control Block (CCB) : 0x0x3D816D70
    State of The Call        : STATE_ACTIVE
    TCP Sockets Used         : NO
    Calling Number           : 0218091323
    Called Number            : 0862000000
    Source IP Address (Sig  ): 10.18.81.2
    Destn SIP Req Addr:Port  : 10.18.81.11:5060
    Destn SIP Resp Addr:Port : 10.18.81.11:5060
    Destination Name         : 10.18.81.11
    PM-HO-VG-01#
    Nov 30 11:44:31.730: //64510/3CD5D2000001/SIP/Call/sipSPIMediaCallInfo: 
    Number of Media Streams: 1
    Media Stream             : 1
    Negotiated Codec         : g729br8
    Negotiated Codec Bytes   : 20
    Nego. Codec payload      : 18 (tx), 18 (rx)
    Negotiated Dtmf-relay    : 6
    Dtmf-relay Payload       : 101 (tx), 101 (rx)
    Source IP Address (Media): 10.18.81.2
    Source IP Port    (Media): 22350
    Destn  IP Address (Media): 10.18.80.40
    Destn  IP Port    (Media): 21928
    Orig Destn IP Address:Port (Media): [ - ]:0
    PM-HO-VG-01#sh sip
    PM-HO-VG-01#sh sip-ua call
    PM-HO-VG-01#sh sip-ua calls 
    Total SIP call legs:2, User Agent Client:1, User Agent Server:1
    SIP UAC CALL INFO
    Call 1
    SIP Call ID                : [email protected]
       State of the call       : STATE_ACTIVE (7)
       Substate of the call    : SUBSTATE_NONE (0)
       Calling Number          : 27218091323
       Called Number           : 0862000000
       Bit Flags               : 0xC04018 0x10000100 0x0
       CC Call ID              : 64511
       Source IP Address (Sig ): 10.18.81.2
       Destn SIP Req Addr:Port : [10.111.111.254]:5060
       Destn SIP Resp Addr:Port: [10.111.111.254]:5060
       Destination Name        : 10.111.111.254
       Number of Media Streams : 1
       Number of Active Streams: 1
       RTP Fork Object         : 0x0
       Media Mode              : flow-through
       Media Stream 1
         State of the stream      : STREAM_ACTIVE
         Stream Call ID           : 64511
         Stream Type              : voice+dtmf (0)
         Stream Media Addr Type   : 1
         Negotiated Codec         : g729br8 (20 bytes)
         Codec Payload Type       : 18 
         Negotiated Dtmf-relay    : rtp-nte
         Dtmf-relay Payload Type  : 101
         QoS ID                   : -1
         Local QoS Strength       : BestEffort
         Negotiated QoS Strength  : BestEffort
         Negotiated QoS Direction : None
         Local QoS Status         : None
         Media Source IP Addr:Port: [10.18.81.2]:22256
         Media Dest IP Addr:Port  : [10.111.111.254]:20074
    Options-Ping    ENABLED:NO    ACTIVE:NO
       Number of SIP User Agent Client(UAC) calls: 1
    SIP UAS CALL INFO
    Call 1
    SIP Call ID                : [email protected]
       State of the call       : STATE_ACTIVE (7)
       Substate of the call    : SUBSTATE_NONE (0)
       Calling Number          : 0218091323
       Called Number           : 0862000000
       Bit Flags               : 0xC0401E 0x10000100 0x80004
       CC Call ID              : 64510
       Source IP Address (Sig ): 10.18.81.2
       Destn SIP Req Addr:Port : [10.18.81.11]:5060
       Destn SIP Resp Addr:Port: [10.18.81.11]:5060
       Destination Name        : 10.18.81.11
       Number of Media Streams : 1
       Number of Active Streams: 1
       RTP Fork Object         : 0x0
       Media Mode              : flow-through
       Media Stream 1
         State of the stream      : STREAM_ACTIVE
         Stream Call ID           : 64510
         Stream Type              : voice+dtmf (1)
         Stream Media Addr Type   : 1
         Negotiated Codec         : g729br8 (20 bytes)
         Codec Payload Type       : 18 
         Negotiated Dtmf-relay    : rtp-nte
         Dtmf-relay Payload Type  : 101
         QoS ID                   : -1
         Local QoS Strength       : BestEffort
         Negotiated QoS Strength  : BestEffort
         Negotiated QoS Direction : None
         Local QoS Status         : None
         Media Source IP Addr:Port: [10.18.81.2]:22350
         Media Dest IP Addr:Port  : [10.18.80.40]:21928
    Options-Ping    ENABLED:NO    ACTIVE:NO
       Number of SIP User Agent Server(UAS) calls: 1
    PM-HO-VG-01#
    PM-HO-VG-01#
    PM-HO-VG-01#
    As you can see, the call is connected and everything is working perfectly. When I press the hold button, here is what I get:
    NOTE: I have # debug ccsip messages and #debug ccsip calls (running)
    PM-HO-VG-01#
    PM-HO-VG-01#
    Nov 30 11:44:49.210: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Received: 
    INVITE sip:[email protected]:5060 SIP/2.0
    Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e720852ab8b92
    From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
    To: <sip:[email protected]>;tag=3C365010-1E42
    Date: Sun, 30 Nov 2014 11:44:49 GMT
    Call-ID: [email protected]
    Supported: timer,resource-priority,replaces
    Min-SE:  1800
    User-Agent: Cisco-CUCM9.1
    Allow: INVITE, OPTIONS, INFO, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY
    CSeq: 102 INVITE
    Max-Forwards: 70
    Expires: 180
    Allow-Events: presence
    Supported: X-cisco-srtp-fallback
    Supported: Geolocation
    Contact: <sip:[email protected]:5060>
    Content-Type: application/sdp
    Content-Length: 244
    v=0
    o=CiscoSystemsCCM-SIP 9082578 2 IN IP4 10.18.81.11
    s=SIP Call
    c=IN IP4 0.0.0.0
    b=TIAS:8000
    b=AS:8
    t=0 0
    m=audio 21928 RTP/AVP 18 101
    a=rtpmap:18 G729/8000
    a=ptime:20
    a=inactive
    a=rtpmap:101 telephone-event/8000
    a=fmtp:101 0-15
    Nov 30 11:44:49.218: //64510/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Sent: 
    SIP/2.0 100 Trying
    Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e720852ab8b92
    From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
    To: <sip:[email protected]>;tag=3C365010-1E42
    Date: Sun, 30 Nov 2014 11:44:49 GMT
    Call-ID: [email protected]
    CSeq: 102 INVITE
    Allow-Events: telephone-event
    Server: Cisco-SIPGateway/IOS-15.2.4.M5
    Content-Length: 0
    Nov 30 11:44:49.218: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Sent: 
    INVITE sip:[email protected]:5060;transport=udp SIP/2.0
    Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3EC9241
    From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
    To: <sip:[email protected]>;tag=71913148-1417348035284
    Date: Sun, 30 Nov 2014 11:44:49 GMT
    Call-ID: [email protected]
    Supported: 100rel,timer,resource-priority,replaces,sdp-anat
    Min-SE:  1800
    Cisco-Guid: 1020645888-0000065536-0000124117-0189862410
    User-Agent: Cisco-SIPGateway/IOS-15.2.4.M5
    Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
    CSeq: 102 INVITE
    Max-Forwards: 70
    Timestamp: 1417347889
    Contact: <sip:[email protected]:5060>
    Call-Info: <sip:10.18.81.2:5060>;method="NOTIFY;Event=telephone-event;Duration=2000"
    Expires: 180
    Allow-Events: telephone-event
    Content-Type: application/sdp
    Content-Length: 271
    v=0
    o=CiscoSystemsSIP-GW-UserAgent 7676 6959 IN IP4 10.18.81.2
    s=SIP Call
    c=IN IP4 0.0.0.0
    t=0 0
    m=audio 22256 RTP/AVP 18 101
    c=IN IP4 0.0.0.0
    a=inactive
    a=rtpmap:18 G729/8000
    a=fmtp:18 annexb=yes
    a=rtpmap:101 telephone-event/8000
    a=fmtp:101 0-15
    a=ptime:20
    Nov 30 11:44:49.278: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Received: 
    SIP/2.0 200 OK
    Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3EC9241
    From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
    To: <sip:[email protected]>;tag=71913148-1417348035284
    Call-ID: [email protected]
    CSeq: 102 INVITE
    Timestamp: 1417347889
    Allow: ACK,BYE,CANCEL,INFO,INVITE,OPTIONS,PRACK,REFER,NOTIFY,UPDATE
    Supported: 
    Accept: application/media_control+xml,application/sdp,application/xml
    Contact: <sip:[email protected]:5060;transport=udp>
    X-BroadWorks-Correlation-Info: bbf94839-a234-4237-95e6-a7037322f0f4
    Content-Type: application/sdp
    Content-Length: 360
    v=0
    o=BroadWorks 316169737 2 IN IP4 10.111.111.254
    s=-
    c=IN IP4 0.0.0.0
    t=0 0
    m=audio 20074 RTP/AVP 18 101 100
    a=rtpmap:101 telephone-event/8000
    a=fmtp:101 0-15
    a=rtpmap:100 X-NSE/8000
    a=fmtp:100 200-202
    a=X-sqn:0
    a=X-cap: 1 audio RTP/AVP 100
    a=X-cpar: a=rtpmap:100 X-NSE/8000
    a=X-cpar: a=fmtp:100 200-202
    a=X-cap: 2 image udptl t38
    a=inactive
    Nov 30 11:44:49.278: //64511/3CD5D2000001/SIP/Call/sipSPICallInfo: 
    The Call Setup Information is:
    Call Control Block (CCB) : 0x0x3D7B1458
    State of The Call        : STATE_ACTIVE
    TCP Sockets Used         : NO
    Calling Number           : 27218091323
    Called Number            : 0862000000
    Source IP Address (Sig  ): 10.18.81.2
    Destn SIP Req Addr:Port  : 10.111.111.254:5060
    Destn SIP Resp Addr:Port : 10.111.111.254:5060
    Destination Name         : 10.111.111.254
    Nov 30 11:44:49.278: //64511/3CD5D2000001/SIP/Call/sipSPIMediaCallInfo: 
    Number of Media Streams: 1
    Media Stream             : 1
    Negotiated Codec         : g729br8
    Negotiated Codec Bytes   : 20
    Nego. Codec payload      : 18 (tx), 18 (rx)
    Negotiated Dtmf-relay    : 6
    Dtmf-relay Payload       : 101 (tx), 101 (rx)
    Source IP Address (Media): 10.18.81.2
    Source IP Port    (Media): 22256
    Destn  IP Address (Media): 0.0.0.0
    Destn  IP Port    (Media): 20074
    Orig Destn IP Address:Port (Media): [ - ]:0
    Nov 30 11:44:49.282: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Sent: 
    ACK sip:[email protected]:5060;transport=udp SIP/2.0
    Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3ECA2633
    From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
    To: <sip:[email protected]>;tag=71913148-1417348035284
    Date: Sun, 30 Nov 2014 11:44:49 GMT
    Call-ID: [email protected]
    Max-Forwards: 70
    CSeq: 102 ACK
    Allow-Events: telephone-event
    Content-Length: 0
    Nov 30 11:44:49.282: //64510/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Sent: 
    SIP/2.0 200 OK
    Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e720852ab8b92
    From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
    To: <sip:[email protected]>;tag=3C365010-1E42
    Date: Sun, 30 Nov 2014 11:44:49 GMT
    Call-ID: [email protected]
    CSeq: 102 INVITE
    Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
    Allow-Events: telephone-event
    Contact: <sip:[email protected]:5060>
    Supported: replaces
    Supported: sdp-anat
    Server: Cisco-SIPGateway/IOS-15.2.4.M5
    Supported: timer
    Content-Type: application/sdp
    Content-Length: 271
    v=0
    o=CiscoSystemsSIP-GW-UserAgent 7965 2748 IN IP4 10.18.81.2
    s=SIP Call
    c=IN IP4 0.0.0.0
    t=0 0
    m=audio 22350 RTP/AVP 18 101
    c=IN IP4 0.0.0.0
    a=inactive
    a=rtpmap:18 G729/8000
    a=fmtp:18 annexb=yes
    a=rtpmap:101 telephone-event/8000
    a=fmtp:101 0-15
    a=ptime:20
    Nov 30 11:44:49.282: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Received: 
    ACK sip:[email protected]:5060 SIP/2.0
    Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e72094953dfea
    From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
    To: <sip:[email protected]>;tag=3C365010-1E42
    Date: Sun, 30 Nov 2014 11:44:49 GMT
    Call-ID: [email protected]
    Max-Forwards: 70
    CSeq: 102 ACK
    Allow-Events: presence
    Content-Length: 0
    Nov 30 11:44:49.290: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Received: 
    INVITE sip:[email protected]:5060 SIP/2.0
    Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e720a6918040f
    From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
    To: <sip:[email protected]>;tag=3C365010-1E42
    Date: Sun, 30 Nov 2014 11:44:49 GMT
    Call-ID: [email protected]
    Supported: timer,resource-priority,replaces
    Min-SE:  1800
    User-Agent: Cisco-CUCM9.1
    Allow: INVITE, OPTIONS, INFO, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY
    CSeq: 103 INVITE
    Max-Forwards: 70
    Expires: 180
    Allow-Events: presence
    Supported: X-cisco-srtp-fallback
    Supported: Geolocation
    Contact: <sip:[email protected]:5060>
    Content-Length: 0
    Nov 30 11:44:49.294: //64510/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Sent: 
    SIP/2.0 100 Trying
    Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e720a6918040f
    From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
    To: <sip:[email protected]>;tag=3C365010-1E42
    Date: Sun, 30 Nov 2014 11:44:49 GMT
    Call-ID: [email protected]
    CSeq: 103 INVITE
    Allow-Events: telephone-event
    Server: Cisco-SIPGateway/IOS-15.2.4.M5
    Content-Length: 0
    Nov 30 11:44:49.294: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Sent: 
    INVITE sip:[email protected]:5060;transport=udp SIP/2.0
    Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3ECB16F3
    From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
    To: <sip:[email protected]>;tag=71913148-1417348035284
    Date: Sun, 30 Nov 2014 11:44:49 GMT
    Call-ID: [email protected]
    Supported: timer,resource-priority,replaces,sdp-anat
    Min-SE:  1800
    Cisco-Guid: 1020645888-0000065536-0000124117-0189862410
    User-Agent: Cisco-SIPGateway/IOS-15.2.4.M5
    Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
    CSeq: 103 INVITE
    Max-Forwards: 70
    Timestamp: 1417347889
    Contact: <sip:[email protected]:5060>
    Expires: 180
    Allow-Events: telephone-event
    Content-Length: 0
    Nov 30 11:44:49.338: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Received: 
    SIP/2.0 200 OK
    Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3ECB16F3
    From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
    To: <sip:[email protected]>;tag=71913148-1417348035284
    Call-ID: [email protected]
    CSeq: 103 INVITE
    Timestamp: 1417347889
    Allow: ACK,BYE,CANCEL,INFO,INVITE,OPTIONS,PRACK,REFER,NOTIFY,UPDATE
    Supported: 
    Accept: application/media_control+xml,application/sdp,application/xml
    Contact: <sip:[email protected]:5060;transport=udp>
    Content-Type: application/sdp
    Content-Length: 306
    v=0
    o=BroadWorks 316169737 3 IN IP4 10.111.111.254
    s=-
    c=IN IP4 10.111.111.254
    t=0 0
    m=audio 20074 RTP/AVP 18 101
    a=rtpmap:101 telephone-event/8000
    a=fmtp:101 0-15
    a=X-sqn:0
    a=X-cap: 1 audio RTP/AVP 100
    a=X-cpar: a=rtpmap:100 X-NSE/8000
    a=X-cpar: a=fmtp:100 200-202
    a=X-cap: 2 image udptl t38
    Nov 30 11:44:49.342: //64510/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Sent: 
    SIP/2.0 2
    PM-HO-VG-01#00 OK
    Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e720a6918040f
    From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
    To: <sip:[email protected]>;tag=3C365010-1E42
    Date: Sun, 30 Nov 2014 11:44:49 GMT
    Call-ID: [email protected]
    CSeq: 103 INVITE
    Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
    Allow-Events: telephone-event
    Contact: <sip:[email protected]:5060>
    Supported: replaces
    Supported: sdp-anat
    Server: Cisco-SIPGateway/IOS-15.2.4.M5
    Supported: timer
    Content-Type: application/sdp
    Content-Length: 289
    v=0
    o=CiscoSystemsSIP-GW-UserAgent 7965 2749 IN IP4 10.18.81.2
    s=SIP Call
    c=IN IP4 10.18.81.2
    t=0 0
    m=audio 22350 RTP/AVP 18 101 19
    c=IN IP4 10.18.81.2
    a=rtpmap:18 G729/8000
    a=fmtp:18 annexb=yes
    a=rtpmap:101 telephone-event/8000
    a=fmtp:101 0-15
    a=rtpmap:19 CN/8000
    a=ptime:20
    Nov 30 11:44:49.350: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Received: 
    ACK sip:[email protected]:5060 SIP/2.0
    Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e720b594cd517
    From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
    To: <sip:[email protected]>;tag=3C365010-1E42
    Date: Sun, 30 Nov 2014 11:44:49 GMT
    Call-ID: [email protected]
    Max-Forwards: 70
    CSeq: 103 ACK
    Allow-Events: presence
    Content-Type: application/sdp
    Content-Length: 213
    v=0
    o=CiscoSystemsCCM-SIP 9082578 3 IN IP4 10.18.81.11
    s=SIP Call
    c=IN IP4 10.18.81.10
    t=0 0
    m=audio 4000 RTP/AVP 18
    a=X-cisco-media:umoh
    a=rtpmap:18 G729/8000
    a=ptime:20
    a=fmtp:18 annexb=no
    a=sendonly
    Nov 30 11:44:49.354: //64510/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Sent: 
    BYE sip:[email protected]:5060 SIP/2.0
    Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3ECC55
    From: <sip:[email protected]>;tag=3C365010-1E42
    To: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
    Date: Sun, 30 Nov 2014 11:44:49 GMT
    Call-ID: [email protected]
    User-Agent: Cisco-SIPGateway/IOS-15.2.4.M5
    Max-Forwards: 70
    Timestamp: 1417347889
    CSeq: 101 BYE
    Reason: Q.850;cause=86
    P-RTP-Stat: PS=874,OS=17480,PR=872,OR=17440,PL=0,JI=0,LA=0,DU=17
    Content-Length: 0
    Nov 30 11:44:49.354: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Sent: 
    BYE sip:[email protected]:5060;transport=udp SIP/2.0
    Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3ECD1ECD
    From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
    To: <sip:[email protected]>;tag=71913148-1417348035284
    Date: Sun, 30 Nov 2014 11:44:49 GMT
    Call-ID: [email protected]
    User-Agent: Cisco-SIPGateway/IOS-15.2.4.M5
    Max-Forwards: 70
    Timestamp: 1417347889
    CSeq: 104 BYE
    Reason: Q.850;cause=65
    P-RTP-Stat: PS=872,OS=17440,PR=952,OR=19040,PL=0,JI=0,LA=0,DU=17
    Content-Length: 0
    Nov 30 11:44:49.374: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Received: 
    SIP/2.0 200 Race Condition
    Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3ECD1ECD
    From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
    To: <sip:[email protected]>;tag=71913148-1417348035284
    Call-ID: [email protected]
    Timestamp: 1417347889
    CSeq: 104 BYE
    Content-Length: 0
    Nov 30 11:44:49.374: //64511/3CD5D2000001/SIP/Call/sipSPICallInfo: 
    The Call Setup Information is:
    Call Control Block (CCB) : 0x0x3D7B1458
    State of The Call        : STATE_DEAD
    TCP Sockets Used         : NO
    Calling Number           : 27218091323
    Called Number            : 0862000000
    Source IP Address (Sig  ): 10.18.81.2
    Destn SIP Req Addr:Port  : 10.111.111.254:5060
    Destn SIP Resp Addr:Port : 10.111.111.254:5060
    Destination Name         : 10.111.111.254
    Nov 30 11:44:49.374: //64511/3CD5D2000001/SIP/Call/sipSPIMediaCallInfo: 
    Number of Media Streams: 1
    Media Stream             : 1
    Negotiated Codec         : g729br8
    Negotiated Codec Bytes   : 20
    Nego. Codec payload      : 18 (tx), 18 (rx)
    Negotiated Dtmf-relay    : 6
    Dtmf-relay Payload       : 101 (tx), 101 (rx)
    Source IP Address (Media): 10.18.81.2
    Source IP Port    (Media): 22256
    Destn  IP Address (Media): 10.111.111.254
    Destn  IP Port    (Media): 20074
    Orig Destn IP Address:Port (Media): [ - ]:0
    Nov 30 11:44:49.374: //64511/3CD5D2000001/SIP/Call/sipSPICallInfo: 
    Disconnect Cause (CC)    : 65
    Disconnect Cause (SIP)   : 200
    Nov 30 11:44:49.406: //64510/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
    Received: 
    SIP/2.0 200 OK
    Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3ECC55
    From: <sip:[email protected]>;tag=3C365010-1E42
    To: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
    Date: Sun, 30 Nov 2014 11:44:49 GMT
    Call-ID: [email protected]
    CSeq: 101 BYE
    Content-Length: 0
    Nov 30 11:44:49.406: //64510/3CD5D2000001/SIP/Call/sipSPICallInfo: 
    The Call Setup Information is:
    Call Control Block (CCB) : 0x0x3D816D70
    State of The Call        : STATE_DEAD
    TCP Sockets Used         : NO
    Calling Number           : 0218091323
    Called Number            : 0862000000
    Source IP Address (Sig  ): 10.18.81.2
    Destn SIP Req Addr:Port  : 10.18.81.11:5060
    Destn SIP Resp Addr:Port : 10.18.81.11:5060
    Destination Name         : 10.18.81.11
    Nov 30 11:44:49.406: //64510/3CD5D2000001/SIP/Call/sipSPIMediaCallInfo: 
    Number of Media Streams: 1
    Media Stream             : 1
    Negotiated Codec         : g729br8
    Negotiated Codec Bytes   : 20
    Nego. Codec payload      : 18 (tx), 18 (rx)
    Negotiated Dtmf-relay    : 6
    Dtmf-relay Payload       : 101 (tx), 101 (rx)
    Source IP Address (Media): 10.18.81.2
    Source IP Port    (Media): 22350
    Destn  IP Address (Media): 0.0.0.0
    Destn  IP Port    (Media): 21928
    Orig Destn IP Address:Port (Media): [ - ]:0
    Nov 30 11:44:49.406: //64510/3CD5D2000001/SIP/Call/sipSPICallInfo: 
    Disconnect Cause (CC)    : 86
    Disconnect Cause (SIP)   : 200
    PM-HO-VG-01#

    Hi Manish,
    Again, excellent feedback. Much appreciated.
    I will try the commands suggested above and see if I can get DTMF to work correctly while interworking H.323 and SIP.
    But my ultimate goal is to have SIP all way from the CUCM to the CUBE and from the CUBE to the ITSP.
    If I enable SIP Early Offer with MTP on the CUCM going to the CUBE, all SIP Invite sent from the CUCM to the CUBE uses G.729r8 as the codec and once the call is established using G.729r8 should the ITSP reply with that codec, the call succeed and I am able to see an active MTP session using G.729 when I issue the command # show sccp connections.
    One thing that I saw is that my ITSP love so much sending G.729br8 most of the times, so even if using SIP EO with MTP on the SIP Trunk to the CUBE, when I sent my INVITE out from the CUCM to the CUBE using G.729r8, specially on call center numbers such as 0800 numbers, you will see that the call established but the codec being negotiated is G.729br8 which is voice only (missing DTMF).
    I will be doing some intensive test again later on this week and will send the logs. 
    Here is my question to both of you:
    Which is the best way of having a proper SIP to SIP setup all the way that will not pose any problem?
    Do I have to enable Early Offer on the SIP Profile used by the CUBE SIP Trunk or should I use the normal Standard SIP Profile? Do I need to enable MTP on my CUBE SIP Trunk or not?
    From the CUBE point of view, I have a voice class codec that support G.729r8 or G.729br8 and the DTMF Relay method supported by the ITSP is RFC 2833.
    I will send more logs for each scenario. I think that we are getting close to the resolution of this problem.
    Thanks again for your support fellows.

  • Callcentric SIP Trunk (ITSP -- 2811 CUBE -- CUCM 8.6

    I have a SIP trunk from call centric that goes into my lab gear - they appear to be a good sip service due to cost but I'm having some trouble getting calls to route correctly. The call flow is Callcentric.com ITSP (SIP) --> 2811 (acting as cube) -->SIP Trunk --> CUCM 8.6. Phones are registered to CUCM.
    I have the sip trunk registered and calls come in to the router (I see them in ccsip message/call debugs) The 2811 running  15.1(4)M7). Callcentric sends the username of the customer in the sip Invite instead of the called number, the called number is in the TO field. I have several DID’s from Callcentric (18452055544, 18452055545, 18452055546) for my lab. There are a few configs on here for CME where the customer number (17772253754) is simply translated to their phone DN - which is fine if you only have 1 DN with callcentric but more than 1 and thats not feasible since every inbound did will be matched to that 17772253754 translation/phone dn.
    I’m using the a guide from http://tblog.cisco.be/2011/02/17/cube-conditional-sip-profiles/ using the Copy function as described http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/ios-software-release-15-1-3-t/product_bulletin_c25-635704.html
    I haven’t been able to find anything where they actually explain all the header fields so Its mostly trial and error.. so far mostly error.  I think I’m close.. but who knows. Any assistance would be greatly appreciated
    voice class sip-profiles 1
    request INVITE peer-header sip TO copy ".sip:(.*)@." u01
    request INVITE sip-header SIP-Req-URI modify ".*@(.*)" "INVITE sip:\u01@\1"
    CUCM (single/pub)- 192.168.1.200
    2811 acting as cube - 192.168.1.203
    Calling Number - 18165297500
    Called Number - 18452055544
    vrtr1#show  sip register status
    Line                             peer       expires(sec) registered P-Associ-URI
    ================================ ========== ============ ========== ============
    17772253754                      -1         20           yes
    vrtr1#
    The Call Setup Information is:
    Call Control Block (CCB) : 0x49646C28
    State of The Call        : STATE_DEAD
    TCP Sockets Used         : NO
    Calling Number           : 18165297500
    Called Number            : 17772253754 (my customer number not called number)
    Source IP Address (Sig  ): 192.168.1.203 (my 2811 router)
    Destn SIP Req Addr:Port  : 204.11.192.159:5080
    Destn SIP Resp Addr:Port : 204.11.192.159:5080
    Destination Name         : 204.11.192.159
    Feb 14 11:20:53.303: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Received:
    INVITE sip:[email protected]:5060 SIP/2.0
    v: SIP/2.0/UDP 204.11.192.159:5080;branch=z9hG4bK-805ff2443b18502ff96181045b62dd74
    f: <sip:[email protected]>;tag=3601387252-874282
    t: <sip:[email protected]>
    i: [email protected]
    CSeq: 1 INVITE
    Max-Forwards: 8
    m: <sip:[email protected]:5080;transport=udp>
    Supported: timer
    c: application/sdp
    l: 350
    v=0
    o=NexTone-MSW 2147483647 2147483647 IN IP4 204.11.192.159
    s=sip call
    c=IN IP4 204.11.192.159
    t=0 0
    m=audio 61094 RTP/AVP 18 0 8 101
    a=fmtp:18 annexb=no
    a=fmtp:101 0-15
    a=rtpmap:101 telephone-event/8000
    a=rtpmap:8 PCMA/8000
    a=rtpmap:0 PCMU/8000
    a=rtpmap:18 G729/8000
    a=ptime:20
    a=sendrecv
    a=silenceSupp:off - - - -
    a=setup:actpass
    Feb 14 11:20:53.327: //936/310B294680AD/SIP/Msg/ccsipDisplayMsg:
    Sent:
    SIP/2.0 100 Trying
    Via: SIP/2.0/UDP 204.11.192.159:5080;branch=z9hG4bK-805ff2443b18502ff96181045b62dd74
    From: <sip:[email protected]>;tag=3601387252-874282
    To: <sip:[email protected]>
    Date: Fri, 14 Feb 2014 17:20:53 GMT
    Call-ID: [email protected]
    CSeq: 1 INVITE
    Allow-Events: telephone-event
    Server: Cisco-SIPGateway/IOS-12.x
    Content-Length: 0
    Feb 14 11:20:53.327: //936/310B294680AD/SIP/Msg/ccsipDisplayMsg:
    Sent:
    SIP/2.0 404 Not Found
    Via: SIP/2.0/UDP 204.11.192.159:5080;branch=z9hG4bK-805ff2443b18502ff96181045b62dd74
    From: <sip:[email protected]>;tag=3601387252-874282
    To: <sip:[email protected]>;tag=35399D8-63
    Date: Fri, 14 Feb 2014 17:20:53 GMT
    Call-ID: [email protected]
    CSeq: 1 INVITE
    Allow-Events: telephone-event
    Server: Cisco-SIPGateway/IOS-12.x
    Reason: Q.850;cause=1
    Content-Length: 0
    Feb 14 11:20:53.419: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Received:
    ACK sip:[email protected]:5060 SIP/2.0
    v: SIP/2.0/UDP 204.11.192.159:5080;branch=z9hG4bK-805ff2443b18502ff96181045b62dd74
    f: <sip:[email protected]>;tag=3601387252-874282
    t: <sip:[email protected]>;tag=35399D8-63
    i: [email protected]
    CSeq: 1 ACK
    Max-Forwards: 10
    l: 0
    u all
    Feb 14 11:20:57.067: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Received:
    ACK sip:18452055544;cic=0288;rn=6465471001;[email protected]:5070 SIP/2.0
    v: SIP/2.0/UDP 204.11.192.159:5080;branch=z9hG4bK-6bceae47efe9f53b4234698a32ac8beb
    f: <sip:[email protected]>;tag=3601387252-874282
    t: <sip:[email protected]>;tag=35399D8-63
    i: [email protected]
    CSeq: 1 ACK
    Max-Forwards: 8
    l: 0
    ************************** Running Config **************************
    sh run
    vrtr1#sh running-config
    Building configuration...
    Current configuration : 4189 bytes
    ! Last configuration change at 00:34:03 CST Fri Feb 14 2014
    ! NVRAM config last updated at 20:26:58 CST Thu Feb 13 2014
    ! NVRAM config last updated at 20:26:58 CST Thu Feb 13 2014
    version 15.1
    service timestamps debug datetime msec localtime
    service timestamps log datetime msec localtime
    no service password-encryption
    hostname vrtr1
    boot-start-marker
    boot system flash:
    boot system flash flash:c2800nm-ipvoicek9-mz.151-4.M7.bin
    boot-end-marker
    card type t1 0 0
    logging buffered 4096 notifications
    enable password cisco
    no aaa new-model
    memory-size iomem 5
    clock timezone CST -6 0
    clock summer-time CST recurring
    no network-clock-participate wic 0
    dot11 syslog
    ip source-route
    ip cef
    ip name-server 192.168.1.9
    no ipv6 cef
    multilink bundle-name authenticated
    voice service voip
    ip address trusted list
      ipv4 192.168.1.0 255.255.255.0
      ipv4 204.11.192.0 255.255.255.0
    allow-connections h323 to h323
    allow-connections h323 to sip
    allow-connections sip to h323
    allow-connections sip to sip
    supplementary-service h450.12
    no supplementary-service sip moved-temporarily
    no supplementary-service sip refer
    sip
      bind control source-interface FastEthernet0/0
      bind media source-interface FastEthernet0/0
      registrar server expires max 1800 min 1800
      localhost dns:callcentric.com
      outbound-proxy dns:callcentric.com
    voice class codec 1
    codec preference 1 g729r8
    codec preference 2 g711ulaw
    voice class sip-profiles 1
    request INVITE peer-header sip TO copy ".sip:(.*)@." u01
    request INVITE sip-header SIP-Req-URI modify ".*@(.*)" "INVITE sip:\u01@\1"
    voice-card 0
    crypto pki token default removal timeout 0
    license udi pid CISCO2811 sn FTX1133A4QR
    controller T1 0/0/0
    cablelength long 0db
    interface FastEthernet0/0
    description ** LAN **
    ip address 192.168.1.203 255.255.255.0
    duplex auto
    speed auto
    h323-gateway voip interface
    h323-gateway voip bind srcaddr 192.168.1.203
    interface FastEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    ip forward-protocol nd
    no ip http server
    no ip http secure-server
    ip route 0.0.0.0 0.0.0.0 192.168.1.1
    snmp mib persist circuit
    control-plane
    voice-port 0/1/0
    voice-port 0/1/1
    voice-port 0/1/2
    voice-port 0/1/3
    ccm-manager mgcp
    no ccm-manager fax protocol cisco
    ccm-manager music-on-hold
    ccm-manager config server 192.168.1.200 
    ccm-manager config
    mgcp
    mgcp call-agent 192.168.1.200 2427 service-type mgcp version 0.1
    mgcp dtmf-relay voip codec all mode out-of-band
    mgcp rtp unreachable timeout 1000 action notify
    mgcp modem passthrough voip mode nse
    mgcp package-capability rtp-package
    mgcp package-capability sst-package
    mgcp package-capability pre-package
    no mgcp package-capability res-package
    no mgcp package-capability fxr-package
    no mgcp timer receive-rtcp
    mgcp sdp simple
    mgcp fax t38 inhibit
    mgcp rtp payload-type g726r16 static
    mgcp bind control source-interface FastEthernet0/0
    mgcp bind media source-interface FastEthernet0/0
    mgcp profile default
    dial-peer voice 999100 pots
    service mgcpapp
    port 0/1/0
    dial-peer voice 999101 pots
    service mgcpapp
    port 0/1/1
    dial-peer voice 999102 pots
    service mgcpapp
    port 0/1/2
    dial-peer voice 999103 pots
    service mgcpapp
    port 0/1/3
    dial-peer voice 999010 pots
    service mgcpapp
    port 0/1/0
    dial-peer voice 6 voip
    description ## INBOUND DID to CUCM ##
    session protocol sipv2
    session target ipv4:192.168.1.200
    incoming called-number 17772253754
    voice-class sip profiles 1
    dtmf-relay h245-alphanumeric
    no vad
    dial-peer voice 7 voip
    description ## INBOUND DID to CUCM ##
    session protocol sipv2
    session target ipv4:192.168.1.200
    incoming called-number 1845205554[4-5]
    voice-class sip profiles 1
    dtmf-relay h245-alphanumeric
    no vad
    sip-ua
    credentials username 17772253754 password 7 106C1B49111F17194D realm callcentric.com
    authentication username 17772253754 password 7 08035E1E1D11000553 realm callcentric.com
    no remote-party-id
    retry invite 2
    retry register 10
    timers connect 100
    mwi-server dns:callcentric.com expires 3600 port 5060 transport udp
    registrar dns:callcentric.com expires 3600
    sip-server dns:callcentric.com
    host-registrar
    line con 0
    line aux 0
    line vty 0 4
    password cisco
    login
    transport input all
    scheduler allocate 20000 1000
    ntp server 199.102.46.72
    ntp server 23.227.162.123 prefer
    end
    exit

    Thank you for the reply. I've updated the dial-peers as sugested. I'm now seeing an invite go out to my CUCM however the call fails with a 403 (forbidden) which appears to come from the ITSP (Callcentric). I've included a new set of ccsip message debugs and the dial-peers as adjusted. Please let me know what you think.
    dial-peer voice 6 voip
    description ## INBOUND CALL from ITSP ##
    session protocol sipv2
    session target sip-server
    incoming called-number 17772253754
    voice-class sip profiles 1
    dtmf-relay rtp-nte
    no vad
    dial-peer voice 100 voip
    description ## INBOUND DID to CUCM ##
    destination-pattern 17772253754
    session protocol sipv2
    session target ipv4:192.168.1.200
    voice-class sip profiles 1
    dtmf-relay rtp-nte
    no vad
    dial-peer voice 7 voip
    description ## INBOUND DID to CUCM ##
    session protocol sipv2
    session target ipv4:192.168.1.200
    incoming called-number 1845205554[4-5]
    voice-class sip profiles 1
    dtmf-relay rtp-nte
    no vad
    Feb 15 10:18:11.424: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Received:
    INVITE sip:[email protected]:5060 SIP/2.0
    v: SIP/2.0/UDP 204.11.192.164:5080;branch=z9hG4bK-d78945b444598bc22c8509d069f4789d
    f: ;tag=3601469891-655
    t: [email protected]>
    i: [email protected]
    CSeq: 1 INVITE
    Max-Forwards: 8
    m:
    Supported: timer
    c: application/sdp
    l: 350
    v=0
    o=NexTone-MSW 2147483647 2147483647 IN IP4 204.11.192.164
    s=sip call
    c=IN IP4 204.11.192.164
    t=0 0
    m=audio 61782 RTP/AVP 18 0 8 101
    a=fmtp:18 annexb=no
    a=fmtp:101 0-15
    a=rtpmap:101 telephone-event/8000
    a=rtpmap:8 PCMA/8000
    a=rtpmap:0 PCMU/8000
    a=rtpmap:18 G729/8000
    a=ptime:20
    a=sendrecv
    a=silenceSupp:off - - - -
    a=setup:actpass
    Feb 15 10:18:11.456: //2419/9933162D820E/SIP/Msg/ccsipDisplayMsg:
    Sent:
    SIP/2.0 100 Trying
    Via: SIP/2.0/UDP 204.11.192.164:5080;branch=z9hG4bK-d78945b444598bc22c8509d069f4789d
    From: ;tag=3601469891-655
    To: [email protected]>
    Date: Sat, 15 Feb 2014 16:18:11 GMT
    Call-ID: [email protected]
    CSeq: 1 INVITE
    Allow-Events: telephone-event
    Server: Cisco-SIPGateway/IOS-12.x
    Content-Length: 0
    Feb 15 10:18:11.460: //2420/9933162D820E/SIP/Msg/ccsipDisplayMsg:
    Sent:
    INVITE sip:@192.168.1.200:5060 SIP/2.0
    Via: SIP/2.0/UDP 192.168.1.203:5060;branch=z9hG4bK9A91F35
    From: [email protected]>;tag=8408644-12C8
    To:
    Date: Sat, 15 Feb 2014 16:18:11 GMT
    Call-ID: [email protected]
    Supported: 100rel,timer,resource-priority,replaces,sdp-anat
    Min-SE:  1800
    Cisco-Guid: 2570262061-2509443555-2182021079-2501285341
    User-Agent: Cisco-SIPGateway/IOS-12.x
    Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
    CSeq: 101 INVITE
    Timestamp: 1392481091
    Contact:
    Expires: 180
    Allow-Events: telephone-event
    Max-Forwards: 7
    Content-Type: application/sdp
    Content-Disposition: session;handling=required
    Content-Length: 273
    v=0
    o=CiscoSystemsSIP-GW-UserAgent 2786 1511 IN IP4 192.168.1.203
    s=SIP Call
    c=IN IP4 192.168.1.203
    t=0 0
    m=audio 18168 RTP/AVP 18 101
    c=IN IP4 192.168.1.203
    a=rtpmap:18 G729/8000
    a=fmtp:18 annexb=no
    a=rtpmap:101 telephone-event/8000
    a=fmtp:101 0-15
    a=ptime:20
    Feb 15 10:18:11.552: //2420/9933162D820E/SIP/Msg/ccsipDisplayMsg:
    Received:
    SIP/2.0 407 Proxy Authentication Required
    v: SIP/2.0/UDP 192.168.1.203:5060;branch=z9hG4bK9A91F35;rport=57100;received=24.123.98.94
    f: [email protected]>;tag=8408644-12C8
    t:
    i: [email protected]
    CSeq: 101 INVITE
    Proxy-Authenticate: Digest realm="callcentric.com", domain="sip:callcentric.com", nonce="8ae6b7b1cea74cf401e8a26fd3c7371b", opaque="", stale=TRUE, algorithm=MD5
    l: 0
    Feb 15 10:18:11.560: //2420/9933162D820E/SIP/Msg/ccsipDisplayMsg:
    Sent:
    ACK sip:[email protected]:5060 SIP/2.0
    Via: SIP/2.0/UDP 192.168.1.203:5060;branch=z9hG4bK9A91F35
    From: [email protected]>;tag=8408644-12C8
    To:
    Date: Sat, 15 Feb 2014 16:18:11 GMT
    Call-ID: [email protected]
    Max-Forwards: 70
    CSeq: 101 ACK
    Allow-Events: telephone-event
    Content-Length: 0
    Feb 15 10:18:11.560: //2420/9933162D820E/SIP/Msg/ccsipDisplayMsg:
    Sent:
    INVITE sip:@192.168.1.200:5060 SIP/2.0
    Via: SIP/2.0/UDP 192.168.1.203:5060;branch=z9hG4bK9AA1BA3
    From: [email protected]>;tag=8408644-12C8
    To:
    Date: Sat, 15 Feb 2014 16:18:11 GMT
    Call-ID: [email protected]
    Supported: 100rel,timer,resource-priority,replaces,sdp-anat
    Min-SE:  1800
    Cisco-Guid: 2570262061-2509443555-2182021079-2501285341
    User-Agent: Cisco-SIPGateway/IOS-12.x
    Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
    CSeq: 102 INVITE
    Timestamp: 1392481091
    Contact:
    Expires: 180
    Allow-Events: telephone-event
    Proxy-Authorization: Digest username="17772253754",realm="callcentric.com",uri="sip:[email protected]:5060",response="a381f10fbbfbd255b444569fef0dddfe",nonce="8ae6b7b1cea74cf401e8a26fd3c7371b",opaque="",algorithm=MD5
    Max-Forwards: 7
    Content-Type: application/sdp
    Content-Disposition: session;handling=required
    Content-Length: 273
    v=0
    o=CiscoSystemsSIP-GW-UserAgent 2786 1511 IN IP4 192.168.1.203
    s=SIP Call
    c=IN IP4 192.168.1.203
    t=0 0
    m=audio 18168 RTP/AVP 18 101
    c=IN IP4 192.168.1.203
    a=rtpmap:18 G729/8000
    a=fmtp:18 annexb=no
    a=rtpmap:101 telephone-event/8000
    a=fmtp:101 0-15
    a=ptime:20
    Feb 15 10:18:11.648: //2420/9933162D820E/SIP/Msg/ccsipDisplayMsg:
    Received:
    SIP/2.0 403 Incorrect Authentication
    v: SIP/2.0/UDP 192.168.1.203:5060;branch=z9hG4bK9AA1BA3;rport=57100;received=24.123.98.94
    f: [email protected]>;tag=8408644-12C8
    t:
    i: [email protected]
    CSeq: 102 INVITE
    l: 0
    Feb 15 10:18:11.660: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Sent:
    ACK sip:[email protected]:5060 SIP/2.0
    Via: SIP/2.0/UDP 192.168.1.203:5060;branch=z9hG4bK9AA1BA3
    From: [email protected]>;tag=8408644-12C8
    To:
    Date: Sat, 15 Feb 2014 16:18:11 GMT
    Call-ID: [email protected]
    Max-Forwards: 70
    CSeq: 102 ACK
    Allow-Events: telephone-event
    Content-Length: 0
    Feb 15 10:18:11.660: //2419/9933162D820E/SIP/Msg/ccsipDisplayMsg:
    Sent:
    SIP/2.0 403 Forbidden
    Via: SIP/2.0/UDP 204.11.192.164:5080;branch=z9hG4bK-d78945b444598bc22c8509d069f4789d
    From: ;tag=3601469891-655
    To: [email protected]>;tag=8408714-B60
    Date: Sat, 15 Feb 2014 16:18:11 GMT
    Call-ID: [email protected]
    CSeq: 1 INVITE
    Allow-Events: telephone-event
    Server: Cisco-SIPGateway/IOS-12.x
    Reason: Q.850;cause=57
    Content-Length: 0
    Feb 15 10:18:11.752: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Received:
    apsc-vrtr1#ACK sip:[email protected]:5060 SIP/2.0
    v: SIP/2.0/UDP 204.11.192.164:5080;branch=z9hG4bK-d78945b444598bc22c8509d069f4789d
    f: ;tag=3601469891-655
    t: [email protected]>;tag=8408714-B60
    i: [email protected]
    CSeq: 1 ACK
    Max-Forwards: 10
    l: 0
    vrtr1#u al
    Feb 15 10:18:14.776: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Received:
    ACK sip:18452055544;cic=0288;rn=6465471001;[email protected]:5070 SIP/2.0
    v: SIP/2.0/UDP 204.11.192.164:5080;branch=z9hG4bK-e437c2c5cac5f1a6e147c1cd7c98aad7
    f: ;tag=3601469891-655
    t: [email protected]>;tag=8408714-B60
    i: [email protected]
    CSeq: 1 ACK
    Max-Forwards: 8
    l: 0

  • Keep-alive problem in apache/weblogic

    I have a server with Weblogic 5.1 and Apache
    1.3.12 with the weblogic-plugin.
    When apache serves pages, the keep-alive works
    fine.
    When weblogic serves pages, the keep-alive works
    fine.
    When i added a handler in apache so all requests
    to apache should go to weblogic through the
    plugin, the keep-alive stopped working.
    Anyone seen this before?
    Gunnar

    send a message to [email protected] with as much info as you can. i d
    on't think they're watching the newsgroups for bug reports.
    maybe someone who frequents the newsgroups regularly could do a FAQ...
    anyone actually got time?
    "Gunnar" <[email protected]> wrote in message
    news:3a51995e$[email protected]..
    In case anyone wondered:
    I tried with sp5 and sp7 and everything worked fine. It seems sp6 is
    buggy...
    Gunnar <[email protected]> skrev i
    meldingsnyheter:3a41e618$[email protected]..
    I have a server with Weblogic 5.1 and Apache
    1.3.12 with the weblogic-plugin.
    When apache serves pages, the keep-alive works
    fine.
    When weblogic serves pages, the keep-alive works
    fine.
    When i added a handler in apache so all requests
    to apache should go to weblogic through the
    plugin, the keep-alive stopped working.
    Anyone seen this before?
    Gunnar

  • How to keep alive a session in Web Services?

    I have to do my project, that will be including some following features:
    1. Login to Application through Web Services method. For example:
    http://mydomain.com/web-services/Login?WSDL
    2. After logging in, use mySms method to send message to Cellphone through Web Services! For example:
    http://mydomain.com/web-services/mySms?WSDL
    My questions are:
    1. How can I keep alive the session after logging in the application in Web Services? In Web, I can use "Session".
    2. If someone has not logged in the Application, he/she could not use mySms method for sending Sms. How can I do that?
    3. I know, when I invoke a Web Services, one JavaBean has been called, and this bean is persistence with his own states. It means, if I set value to parameters of this bean, these values are persistence for invoked methods by other persons.
    For example:
    mySms bean has a private field "jid" inited with NULL value.
    Person A invoked mySms.
    Then, A set jid of mySms to value "A".
    Person B invoked mySms. B got jid value. He receive the result value is "A".
    The question is, how can I set mySms bean so that mySms bean is not persistence?
    Thanks many!

    Hi,
    I can right away answer your FIRST Question.
    Since WebServices are PURELY Based on SOAP which is in tern based on HTTP, they rely on a Stateless protocol.
    I am sure you know that the HTTP is the STATELESS Protocol and so you can not maintain Session and so EACH Http REQUEST is considered as a SEPERATE REQUEST.
    Now, still you want to maintain the Session in WebServices,
    The simple answer is PASSING PARAMETERS.
    Just Maintain your Session on Client (If you are using JSPs or Servlets to CAll WEBSERVICES then maintain Session through your HTTPSession) and each time you Invoke WebService PASS ON REQUIRED Parameters.
    This Approach is Exactly like your URL REWriting OR your Parameters Passing through QUERY STRINGS.
    I hope you got what I am saying!
    Take care,
    Himanshu/

  • WRT54G v 7.0 -- Setting "Keep Alive: Redial Period" not correct (radio button)

    Hi,
    I own a Linksys-Router WRT54G v7.0 with firmware v7.00.8 build 008, Jul. 9, 2009.
    On the web GUI (Setup/Basic Setup) there's a setting "Keep Alive: Redial Period XX Sec.". As I'd like to stay connected with my provider permanently, I've set the radio button to "Keep Alive: Redial Period" and the according text field to "30" seconds. Then, I've clicked "Save Settings" and got a confirmation message that the settings got saved.
    Anyway, even after saving the settings the according radio button is still set to "Connect on Demand...". But that is only true for newer browsers, like e.g. IE8, IE7 or Firefox 8. If you use an older browser, like e.g. IE6, then the radio button is correctly set to "Keep Alive: Redial Period" with a value of "30" seconds.
    Conclusion: The settings get correctly saved by the router (I can confirm that), but they don't get correctly shown in the web GUI. Looks like a HTML/Javascript bug in the router's admin web GUI. That's really annoying as you never exactly know the effective settings...
    Can someone confirm that bug? Is there a newer firmware than version 7.00.8? 
    Regards,
    Patrick

    Try to clear the browser's cache as well.
    "Don't fix it if it ain't broken."

Maybe you are looking for

  • Which is better Truphone or Fring? Neither? Opinions wanted

    My husband and I travel overseas periodically. We like to stay in touch with adult kids, one of who has an iPhone. Not a lot of talking, just periodic sort of "we're here, all is well. How are you?" It looks as if some sort of voip plan would save a

  • I can't download Skype for iPad

    Whenever I try to download Skype for I iPad this message appears: "You have already purchased this app. It will start downloading without any further payment." (Translation to English) I downloaded  Skype before for my iPhone. Now there is this littl

  • Web Export

    ok I shot some footage -- 720x480 SD at 24fps anamorphic 16:9 aspect ratio -- looks great but Ive been trying to export it for the web and Im getting nowhere fast! I tried "Export Quicktime Movie" and Ive tried to use Quicktime conversion... when I t

  • N97 mini not BT with anything

    OK i've just upgraded from N95 8gb to N97 mini. Great I thought I'll have no issues with paring and making calls with JVC car kit. Now my N95 worked perfectly with no dropped calls and it could stream audio and video to the JVC unit all day long with

  • HP 6510 Scanning issue with Windows 8

    Windows 8 Using a shortcut HPFE 89CC (HP Photosmart 6510) I can print okay wireless, but I cannot Scan ( printer & laptop not connected) What do I need to do ? or What & How do I need to install something that will allow me to scan please