Keep losing BB service on 3G

Hi
I quite often lose this when running via 3G. I am on Virgin UK. It set up an apn on inserting the SIM and it worked over the weekend fine.
Today it wouldn't connect despite restarts etc.
I have just fixed it by changing the apn from goto.virginmobile.uk to a.a.com thinking it would disconnect 3G and I could try inputting it again from scracth.
Rather than it stop working, it started working!!!
Any ideas for this and a better permanent fix? Is it Virgin Mobile not being setup for the Z10?
I'm new to BlackBerry 
Paul

Possible reason:
I get BB at home in Brighton. At work in Burgess Hill I lose BB. May it be because I have roamed onto the Orange signal?

Similar Messages

  • E4200 - Keeps losing uPNP service

    The E4200 keeps losing uPNP service and I have to restart the router to correct it. Is there a fix for this?

    Is your router a version 1 or 2? Is the UPnP for gaming or VOIP to the router? Are you getting an error on the device/s that is using the UPnP service to the router? You might need to open ports on the router to fix the issue and aside from that updating its firmware to  the latest. You have to determine the correct ports that you need to open on the router though (port range forwarding). If you are not sure of what port numbers to forward or open on the router then call the vendor of the device/s you are having trouble with connecting.
    Setting up port range forwarding on Linksys wireless-N routers and gateways
    Manually upgrading the firmware of the Linksys wireless-N router

  • Keep losing all service, and phone restarts on it's own

    So...my Razr maxx kept restarting on it's own after only being on for about 30 seconds and it also was receiving no signal. I did all the troubleshooting tools and nothing seemed to be able to fix it. So i successfully traded it in for a refurbished Razr with a new SIM card. I was able to set it up just fine last night and had no problems with it. However today while at work it just quit receiving a signal. It also has restarted itself multiple times. Seems like the same issue except on a smaller scale. It gets intermittent service and has only restarted itself a couple times. I went through all the settings and everything seems fine. The only thing i can think is that there might be a virus on my microSD card that's causing my phones to act like this. Anyone else experiencing the same issue? Of course Verizon support will just tell me like they tried last time that their working on the towers right now. I don't know if they'll let me get another replacement. I think you only get one every 6 months with insurance. Please help.

    My Razr Maxx was doing the same thing. Now it appears to be booting (constantly), but never actually boots. I can not even turn it off now. The only way it turns off is to let the battery die.
    I've tried all the recommended fixes. In my research, this is a common problem with these phones. The only solution seems to be a new phone. These phones are too expensive to need replacing so often. Hmm...who does that benefit?
    I've lost all interest in owning another Motorola. I'm seriously considering changing providers, as well.

  • I got a replacement iPhone 4s, and now it keeps losing service

    My last phone dropped in the toilet, so I got a replacement phone cause i had apple care.
    When I got this phone i was having problems, but i got help and i fixed it, but now....
    It keeps losing service ALL THE TIME...
    it goes from Verizon 3g to no bars and just Verizon, and then to "Searching...."
    I KNOW ITS NOT MY COMPANY'S FAULT, because verizon is well and it is not like in the mountains where i don;t get service its like all the time and it happens seriously like every 2 minutes, its really annoying because
    my messages won't go through
    apps wont open or reload
    can't make calls
    SO YEAH,
    please anyone help me please.... <3333

    nikkibabyyy7 wrote:
    I KNOW ITS NOT MY COMPANY'S FAULT, because verizon is well and it is not like in the mountains where i don;t get service its like all the time and it happens seriously like every 2 minutes, its really annoying
    Then why are you even asking here.  Obviously you know Verizion could never possibly have network issues.
    Every network has issues from time to time, no network, company, or person is perfect.
    Try basic troubleshooting from the User's Guide and contact Verizon to ensure they are not having issues.

  • Got my iPhone 4S a few days ago. On orange EE in uk. The phone keeps losing signal (no service) never had this problem before with other makes of phone. Please help, thank you.

    Please help. My iPhone 4S keeps losing signal (no service) I am with EE orange uk. The phone is only Agee days old. Never had this issue with previous phones.

    Same problem!!!
    There are many ways to fix it
    First you must change the USB cable... Or download new version iTunes bro...
    Or if your laptop says " the usb  NOT recognize " try to pull up the laptop charger,
    It's work for my device, try this bro !! 
    Im sorry my english is bad!!!

  • My iPhone 4 with IoS 7 keeps randomly turning off. Also, when I plug it into my charger it keeps losing service untill I unplug it. Please help!

    My iPhone 4 with IoS 7 keeps randomly turning off. Also, when I plug it into my charger it keeps losing service untill I unplug it. Please help!

    Take the device to Apple for evaluation.

  • Why do i keep losing service, why do i keep losing service

    Why do i keep losing service on my i phone 4

    Not sure.  What did your carrier say when you contacted them?
    Also, update your iOS: Settings > General > Software Update

  • Why does my iPad keep losing connectivity

    Why does my iPad
    keep losing connectivity ?

    Hi Joan,
    I'm sorry to hear you are having issues connecting with Wi-Fi from your iPad.
    The article below may be able to help you with this issue.
    Click on the link below to see more details and screenshots. 
    I've quoted some helpful highlights for you:
    iOS: Troubleshooting Wi-Fi networks and connections
    Be sure that you are in range of your Wi-Fi router (access point).
    Tap Settings > Wi-Fi and turn Wi-Fi off and then on again.If unable to do so, see this article.
    Confirm that your Wi-Fi router and Cable or DSL modem are connected to power, turned on, and indicate that they are connected to the Internet.If not, refer to your network administrator or ISP for assistance.
    Restart your iOS device.
    Tap Settings > Wi-Fi and locate the Wi-Fi network to which you are connected. Then tap the blue dot and choose Forget this Network. Try to connect to your desired Wi-Fi network again.
    Note: You will need to enter your Wi-Fi password again if your desired network requires one.
    Turn your Wi-Fi router off and then on again2. If your ISP also provides cable or phone service, check with them before attempting this step to avoid interruption of service.
    Update your device to the latest version of software.
    Update your Wi-Fi router to the latest firmware2.For AirPort Base Stations, see this article for information about firmware updates.
    If your issue is still unresolved
    Follow the steps below for the issue you are experiencing.
    Unable to locate a Wi-Fi network
    Unable to connect to a Wi-Fi network
    Wi-Fi disconnects, or signal strength is less than expected
    Unable to access the Internet while connected to Wi-Fi
    Unable to automatically connect to Wi-Fi
    I hope this information helps ....
    Have a great day!
    - Judy

  • Keep losing signal & poor speed

    Hi
    Over the last few days I keep losing my internet connection, I've run several speed tests today connected directly to the router with an ethernet cable & master socket and I'm still struggling to get more than 0.5Mb - usually we average 1.5Mb (Warmwell exchange)
    I've tried replacing the router for a brand new netgear as the BT homehub kept losing the signal even at our old address but it's made no difference and over the last 48 hours it's become unbearable.
    I've done the test using speedster.btcom, that also shows 0.5Mb.
    There are no listed service issues in my area so what's going on?
    Cheers,
    Andy.

    Hi Welcome to the forums
    Here are some help pages done by CL Keith http://forumhelp.dyndns.org/speed/Speed.html
    also post your full hub stats by entering 192.168.1.254 into your web browser address bar and navigate to adsl or use a-z, if netgear enter 192.168.0.1
    Can you also post the full results from BT Speedtest speedtester.bt.com  
    Have you tried connecting to the test socket at the rear of the master socket    
    Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
    This is a customer to customer self help forum the only BT presence here are the forum moderators
    If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

  • Wireless phone keeps losing IP settings

    I have a wirless 7920 wirless phone that keeps losing IP settings, on the front screen it says "Authentication OK" but when tries to get a IP address it fails. The Wlan controller is 4400 series model number 4402

    Not sure if this will help, but people across the country are experiencing difficulties with the roll-out AT&amp;T/SBCglobal/Comcast ISP. They used to pass Internet traffic through their lines like telephone calls, but now their routers have a number of global security measures. These routers now must be programmed for IP passthrough, which assigns devices their own ISP based on the device IP plus an additional ISP identity. In addition, the routers must be programmed to open the ports required for the specific services that the user wants to enable. They couldn't figure out if the higher security settings should be default, or not, so certain events trigger the higher security settings, like traffic from foreign network or an http request within another http request, etc.

  • C3-01 Losing Phone Service

    This phone is on the Virgin network and was supplied by Virgin. The phone keeps losing it's phone connection and the only way I find out is when I try to make a call or get landlines calls from people telling me they can't reach my mobile again!! The strange thing is I still have full signal strength according to the bars on the phone just no connection.
    Having spoken to Virgin they told me to set the "Service Provider" provider option to manual and select virgin. This I did but I still have the problem but can regain connection if I re-scan providers and re-select virgin.
    Speaking to Virgin again they are now telling me to turn off 3g and run in 2g mode. Firstly this suggests they know they have an issue, secondly why the hell should I! I got a 3g phone because I wanted 3g.
    Has anyone seen this sort of problem before?
    Thanks

    Factory settings just do the trick. Hope there wont be more bugs...

  • Keep losing DNS

    I've only had my BT Broadband service a few days, but I keep losing my DNS - names will not resolve, although the actual internet connection is fine. Logging into the hub, and disconnecting/reconnecting the internet connection restores DND, but inevitably the next day it's gone again.
    As a stopgap measure (or perhaps it's the permanent fix?) I've changed to using the "OpenDNS" DNS servers.
    Has anyone else experienced this problem? Do I have a faulty hub, perhaps?
    All advice very welcome.
    Thanks!
    Harry.

    Well if it carries on working , you can leave it. OpenDns is okay.
    Some people are reporting what looks like DNS errors on the BT servers at the moment. So there might be a problem. I do not have a problem myself. But the DNS severs in the HH are picked up automatically on connection and cannot be changed in the HH.
    [edit] Were the DNS problems just on certain sites.
    toekneem
    http://www.no2nuisancecalls.net
    (EASBF)

  • I keep losing my Internet connection on my I mac osx 10.7.5 Wi fi and Ethernet. The only way to reconnect I'd renew dhcp but then it will disconnect again less then a minute

    I keep losing my Internet on Wi fi and Ethernet, on Ethernet if I renew DHCP lease it will start again put within 20/30 seconds it disconnect again. My laptop , iPhone, iPad my other laptop all work with no problems, so it can't be the router any help please, my iMac is around 4 years old

    Hi Ray, no idea what is mentioned in those other links, but...
    this has worked for a few...
    Make a New Location, Using network locations in Mac OS X ...
    http://support.apple.com/kb/HT2712
    10.7 & 10.8…
    System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
    10.5.x/10.6.x/10.7.x instructions...
    System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
    The interface that connects to the Internet should be dragged to the top of the list.
    Is that Interface dragged to the top of Network>Show:>Network Port Configurations.
    Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.
    For 10.5/10.6, System Preferences>Network, unlock the lock if need be, highlight the Interface you use to connect to Internet, click on the advanced button, click on the DNS tab, click on the little plus icon, then add these numbers...
    208.67.222.222
    208.67.220.220
    Click OK.

  • Keep losing broadband

    I keep losing my connection, i stay connected to the router but we lose the internet. Is there anything i can do to fix it or do i have to have someone come out to fix it

    Drusella84 wrote:
    I keep losing my connection, i stay connected to the router but we lose the internet. Is there anything i can do to fix it or do i have to have someone come out to fix it
    If you happen to have a 510/589 RG, IPv6 can be causing disconnects, reboots and browsing problems.  Disable it in the RG UI.
    Chris
    Please NO SD stretch-o-vision or 480 SD HD Channels
    Need Help? PM ATT Uverse Care (all service problems)
    ATT Customer Care(all other problems)
    Your Results May Vary, In My Humble Opinion
    I Call It Like I See It, Simply a U-verse user, nothing more

  • Why do I keep losing connection to my MIFI4510L

    Why do I keep losing connection to my MIFI4510L. After a period of time this device disconnects from the internet. What do I have to do to correct this?

    This seems to be a problem in various areas. I'm in Michigan north of Detroit, when they switched from 3G to 4G, reliability and speed dropped significantly. My first service calls were frustrating as the service tech told me I had unused WIFI setups on my PC and I needed to delete them. told him the device works everywhere else, but he was instant I delete the unused, imagine that fixed nothing. I was sent a replacement device (refurbished without a battery or back) which was worthless as it was different form what I have and could not be used, so I sent it back I have emailed the Customer Service VP for the region and after months of not getting the issue resolved I was told 4G service was in the process of being updated in my area and not to expect it to improve until sometime in 2013. Since the device detects 3G and 4G, it switches to 4G and connection often drops to 1 mbps and cannot even get a Google page. Under 3G, it was pretty consistent at 68 to 72 mbps. My options are to replace my 3G/4G device with a 3G only or change to a different service provider. I have a cottage basically on the fringe area and 3G connects at 68-72 99% of the time and outside of Boston, Washington north of Seattle (almost Canada), Texas, Chicago, etc, 4G works great, so it is not the device. Guess I'm not sure the push to 4G if they are not ready. Guess once the sale is complete they have you and if service is bad, oh well. The sad part, my current cell phone contacts are ending and I was seriously planning on leaving ATT to switch everything to Verizon based on service prior to the switch to 4G, but that does not make any sense now. My Apple 4G can be a hot spot and works great when I' m at home, but why pay for 2 different services. The other interesting note, I left Comcast due to poor service (internet was slow from 6am to 10pm or dropped completely) and now Verizon has teamed up with them... sure hope they are not the cause of poor internet service... like maybe Verizon is using them for internet service... I was told no... but problems started around the same time of the announcement. So based on responses from Verizon, I will check my other options. The commercials are great but reality is delivery, no so great.

Maybe you are looking for

  • Restore new ipod with old ipod data

    I think my ipod is probably toast (unless some genius responds to my last post and solves my problem). If I have to get a new ipod, does anyone know if I can restore the data from my dead one to the new one?

  • Access APO Table details in ECC

    I have a report in ECC which gives me the details about Product and location along with some Material-plant specific details. Now my requirement is to check whether the particular Product & Location is available in APO or not. From R/3 can i use some

  • How to identify activity/ command 'CLOSE' in transaction code CJ02

    Hi, I need to implement a check in transaction code - CJ02 when command 'CLOSE' is performed to close a WBS Element. This check is being planned to be implemented using BADi - WORKBREAKDOWN_UPDATE using 'AT_SAVE' method. However I am unable to captur

  • Condition types in orders

    Hi,       I want to find out in what all sales orders a particular condition type was used. For example there is a condition type k005, now i want to find out in what all sales orders this condition type was used.      Useful responses are highly app

  • Funds Management - Tolerance Limit Messages

    hi gurus In tolerance Profile i have define warning at 90% budget usage and Error at 100% budget usage.When i post a vendor invoice which exceed 90% or 100% a SAP STANDARD  pop up warning & Error message appears. At this stage i want to pop up my own