Keeping display on when Docked

When I have the iPhone connected via a docking station to my stereo, is there a setting where it knows it's docked and will keep the screen on or do I have to manually turn the auto lock feature off?

Manually turn the autolock feature off.

Similar Messages

My iPod Touch keeps displaying the message 'This accessory not supported by iPod touch.' When I've used it w/this device multiple times, it's happening more and more frequently now. Anyway to dismiss this message for good? Because the iPod still plays .

My iPod Touch keeps displaying the message 'This accessory not supported by iPod touch.' When I've used it w/this device multiple times, it's happening more and more frequently now. Anyway to dismiss this message for good? Because the iPod still plays thru my radio and system.

That message is usually due to a bad cable.
Not Charge
- See:
iPod touch: Hardware troubleshooting
iPhone and iPod touch: Charging the battery
If you can’t charge your iPhone, iPad, or iPod touch
- Try another cable. The cable for 5G iPod (lightning connector) seems to be more prone to failure than the older cable.
- If a 5G iPod
Iphone 5 lightning port charging problem - SOLUTION!
- Try another charging source
- Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar
or send it in to Apple. See:
Service Answer Center - iPod

HT201263 I Have an iPhone 5 runnig ios 7.0.4. It wont start as the apple logo keeps on blinking when i connect to wall charger or itunes. I even tried to restore it but an error 21 is being displayed. Any one can help me in this situation

I Have an iPhone 5 runnig ios 7.0.4. It wont start as the apple logo keeps on blinking when i connect to wall charger or itunes. I even tried to restore it but an error 21 is being displayed. Any one can help me in this situation

Read http://support.apple.com/kb/ts3694#

T530 - Dual boot not displayed on external monitor when docked

Hi,
I just got my new T530, loaded all my applications and data from my T61. The T530 is connected to the 4338 docking station.
I have Win 7 on the internal disk, and Win 8 on the ultrabay disk.
Dual boot works fine when undocked, but when docked and the lid is closed I don't see the dual boot selection on the external monitor and the PC boots into Win 7 (which is my default OS).
When cold or warm booting I also don't see the Thinkpad splash screen.
I did not have this problem with my T61 when docked. There the splash screen and dual boot selection was displayed and I was able to select which OS I want to boot into.
Any ideas whet I can do here?
Thanks

As I came across this it's a matter of the two graphic cards and how they are shared.
The Intel always drives the Laptop-Display and the analogue port, the digitalports at the docking are all driven by the Nvidia Card.
The splashscreen will always be displayed with the intel card and therefore not be visible with the digital ports at the docking.
W530 2438 CTO - i7-3720 QM - K2000M - FHD - 16 GB - SSD Samsung 830 Series 128 GB - Windows 7, 64 bit

Dear Sirs,when i use the computer updating my iphone to ios 7.1,suddenly black out.The computer has no power and my iphone does not work and keep display the screen that connect to itunes. so when i connect my iphone to iTunes, it says"itunes has detected

Dear Sirs,when i use the computer updating my iphone to ios 7.1,suddenly black out.The computer has no power and my iphone does not work and keep display the screen saying the iphone need to connect to itunes. So when i connect my iphone to iTunes, the computer says"itunes has detected an iphone in recovery mode. you must restore this iphone before it can be used with itunes"
So my question is if I click OK(restore the iphone),will i lose all my data and whatsapp??
Thank you for your help and time.
Regards,
hopeless

If you didn't back up the phone to iCloud or iTunes (on your computer) BEFORE attempting the update, the data will be lost.

How to keep light of iPod 30GB turned on when docked.

Hi,
My iPod is new and has latest software installed.
The settings of the iPod should keep the light on when docked in iPod-Hifi (main menu-loudspeakers-always on). However, after about ten seconds the light turns off when docked. The light stays turned on when undocked. The timer settings for light are set to always on. Can somebody help and knows what I have to do to keep the light turned on when docked? Thanks.
Paul

Hi,
A straight forward way is for each of you to have your own User Account...
See this Support Article...
How to use multiple iPods, iPads, or iPhones with one computer

Algebra CD keeps displaying "Script run-time error" when I try to open it

I have a CD that came with my Algebra book (I bought it used) for Technical School and it keeps displaying Scrip run-time error when I try to open it. I have updated Quick-time player, just in case that was the problem.

b noir wrote:
Is CoreGraphics.dll cited in the iTunes events?
Also check for error events happening a few seconds prior to the iTunes events. Open those events. Do they all cite the same .ttf file? If so, what's the precise spelling of the .ttf (font) file?
YES! There is a CoreGraphics.dll cited in the iTunes event. This is what exactly the window said
"Faulting application iTunes.exe, version 9.0.3.15, faulting module CoreGraphics.dll, version 1.0.60.0, fault address 0x00266560."
For the .ttf file, this is what it showed.
"Windows cannot access the file C:\WINDOWS\Fonts\ARIALUNI.TTF for one of the following reasons: there is a problem with the network connection, the disk that the file is stored on, or the storage drivers installed on this computer; or the disk is missing. Windows closed the program ARIALUNI.TTF because of this error.
Program: ARIALUNI.TTF
File: C:\WINDOWS\Fonts\ARIALUNI.TTF"
I hope this will help. I still cant open iTunes.

Way to keep Clock always on when docked?

When I first got the nano, I somehow managed to keep the clock always on when it was docked and charging. However, I have not been able to make this work anymore and I don't know what has changed.
It would be nice to dock the nano at night and have a clock face continually show while it's docked and charging, as I use it for my alarm clock.

I just discovered what was going on. Apparently my dock (a JVC model) is somehow causing the iPod nano to stay on continuously when docked, AND powered on. This does not work in standby mode. But suffice it to say, when the nano is docked, I can use the remote to turn the nano on with the unit, and the backlight will stay on until I turn off the dock with the remote again (standby), at which point the nano goes off too.
The nano charges while the dock is in standby mode, but the backlight will not stay on.
So somehow, it is possible to tell the nano to keep the backlight on, via some kind of external signal from the dock, which seems to have nothing to do with having an external power supply attached.
Whatever the reason I have my nano alarm clock back. Now if only it had an alarm sound that sounded continuously until I shut it off ... Good thing I'm a light sleeper.

C5 Anyway to keep the display on when charging

Does any one know if its possible to keep the display on when charging ?
On older Nokia phones you could create a charging profile and ensure the display stays on.
I would like have this when mode when using my car kit....

no this is new powersaving on all nokia phones
If i have helped at all a click on the white star below would be nice thanks.
Now using the Lumia 1520

Why does the 'iCal helper' keep appearing in my dock?

After upgrading to 10.5.6 today the iCal helper application keeps launching and staying in my dock. It's not marked as a log-in item, and doesn't necessarily launch when i log-in. It just launches randomly every hour or so.
I've read that it is the program that allows iCal to display alerts when it's not running, but it never used to be visible in the dock, it doesn't even have a real application icon.
Does someone know how to prevent it from showing up in the dock??
Message was edited by: goughbradley

Anyone??

How to keep display on Macbook Pro instead of Clamshell Mode

I have an extended desktop through a Mini-Display Port-to-VGA connection from my Macbook Pro (OSX Mountain Lion) to an external monitor. I have the Macbook Pro screen set up as the "main screen" (with the display bar on top). But everytime I close my macbook pro, the computer goes into clamshell mode and sets the extended desktop as my "main screen" which switches my display bar. Is there anyway to tell OSX ML to always keep the Macbook Pro screen as the default and not go into clamshell mode?
This also creates a problem when I want to physically close my computer to allow to sleep, but instead goes into clamshell mode and extends the desktop to my external display. Any ideas?

this is from another discussion:
jk10003
Re: MacBook doesn't sleep when closing lid with external monitor attached with Lion Oct 14, 2011 7:01 PM (in response to admgtz)
I would like to offer this solution. I have a MacBook Pro with an external monitor, and, for a year and a half both displays slept when I closed the MBPS. This behavior stopped when I installed Lion. They would sleep when I removed the power cord, but what a pain that would be. The command "pmset -g assertions" gave no indication of which process ought be preventing sleep.
I contacted Apple support, and after some searching, the guy working with me found this thread, which was flagged as an Apple-approved solution:
https://discussions.apple.com/thread/3190417?start=165&tstart=0
This is the important part:
Correct AnswerRe: How do I tell Lion to disable the LCD screen even when the lid is open?
Aug 31, 2011 9:56 AM (in response to Bob_viking)
Here's the command to make your laptop behave like it did Pre-Lion (courtesy of my friend):
sudo nvram boot-args="iog=0x0"
Works perfectly for me. If it screws up your system, just zap the PRAM next boot (cmd-opt-p-r) and you'll be back to the default Lion state. Or if you can still get into terminal, this command will get you back to Lion's default state as well:
sudo nvram -d boot-args
Enjoy!
One snag was that I had to run it with the external monitor disabled, but it worked great!

Stor.e TV+ No Loader error keeps coming up when switching on

I have been experiencing continual problems accessing the hard drive. "No Loader" error message keeps coming up when switching on.
The so-called "solution" to this problem posted on this forum is to open up the box and fiddle with the cables. Whilst I have had some success with this method initially, dismantling the box 10 times a week is not on.
I tried something else in desperation.
When the No Loader message comes up, I switch the box off and on again from the remote.
After 2 or 3 times or so the HDD folder usually appears.
I have been doing this consistently now with great success. This however suggests that the No Loader error message is NOT a mechanical connector problem with the hard drive but (as usual) poor software (what else?).
Dismantling the unit is tantamount to switching it off for an extended period of time so may explain why this technique works.
Switching the unit on and off several times also solves the problem of the D folder not appearing on the network even though Win7 shows Store-TV-Plus as a mapped NTFS drive (but can't find the D folder).
See the similarity?
Another thing that exacerbates problems is the unit's poor ventilation. The first thing that happens with this unit is that the rubbish stick-on rubber feet fall off.
Whilst this may seem innocuous, the ventilation slots are underneath the unit and will be blocked if there are no feet. I live in a hot country so this device gets pretty hot and behaves even more erratically unless well ventilated.
Ideally keep it well away from other units and preferably sit it on a small box by itself with the vents underneath well exposed.
I also still experience problems playing FLAC and MKV files. The unit occasionally loses synch with FLAC files which generally otherwise play OK and locks up or causes loud bangs or white noise on the speakers (dangerous).
Some MKV files just don't play at all even though VLC plays them. There are a myriad other inconsistencies but these are the most annoying.
Is anyone else experiencing these problems or does anyone have any other solutions to prevent these problems?
I don't suppose we can expect another software upgrade from Toshiba? In your dreams, pal.

OK, so I took the risk and updated the firmware of my Stor.e TV+ to the Noontec V8S latest firmware V3.0816.13_V8S from noontec website.
The update went fine without a hitch (took about 2 minutes from an old 256MB flash drive plugged into the back USB port of the unit, which I formatted before using), and some of the irritating shortcomings of the Toshiba firmware was solved. Samba worked in some fashion, but I was still not able to download songs directly to the Stor.e over wireless, which is the only other feature I currently need. The irritating remote control buttons were changed to the way any sane person would use them (I had changed my universal remote control to correct this, so would have to change the settings if I kept the updated firmware) The new firmware seems solid, but I DON'T USE THE VIDEO CAPABLITIES, so I can't comment on this.
One major drawback of this update for me is that the small display on the unit becomes much less readable. Seems like there is a problem with the font on the new firmware. I use my Stor.e exclusively as a flac music player, and since I don't have it connected to a tv the small display is crucial for me to select tracks or disks. I have 300+ discs, so the Stor.e is an excellent cheap media player which I connect to my HIFI system via a DAC.
I thus had to change back to the Toshiba firmware to correct this problem. Seems like I would still have to use USB to download music to the Stor.e when I buy new CDs. What a pity.
Incidentally, the new Toshiba firmware is very much like the old firmware, in that it lacks the capability to switch on Samba. In the readme Toshiba states that the new firmware fixes a network problem, but I think that this is probably the smallest issue most users have with the Toshiba firmware.
So, my advice to anyone having video, control or other issues with the Toshiba firmware is to flash to the Noontec firmware to see if it resolves their issues. If it doesn't one can always revert to the official Toshiba firmware as I did.
You do this at your own risk though, if you brick your unit don't blame me...

Cannot change display resolution when connected to external display

On my 2.0GHz 13" MacBook, I have no problem with the display resolution when connecting to external display/projector when I am running in Mac OS, everything work perfectly! But things start to get messy when I am running in Windows VISTA 32 (installed within the Boot Camp 2.1). Whenever I connect to any external display/projector via a MiniDisplay-to-VGA cable, the resolutions on both my MacBook LCD and external display/projector drop to 640x480. And i am not able increase the resolution in the Display Settings. Does this mean that I have not installed the latest version of display drivers? Or is it that Apple did not provide the VISTA 32 drivers (in Boot Camp 2.1) that is compatible with the Mini Display port.

Cool!
I'm glad you have it fixed.
Please resolve the thread so others can find your answer faster.
Thanks,
Bifocals
Click Accept as Solution for posts that have solved your issue(s)!
Be sure to click Like! for those who have helped you.
Install BlackBerry Protect it's a free application designed to help find your lost BlackBerry smartphone, and keep the information on it secure.

HT4623 I am having trouble with my iPod 5th gen after iOS update. It's in recovery mode and iTunes keeps timing out when I try to restore it. What should I do???

I am having trouble with my iPod 5th gen after iOS update. It's in recovery mode and iTunes keeps timing out when I try to restore it. What should I do??? If possible, I would also like to keep all of my data.

Maybe this will help:
Troubleshooting
As with all clickwheel iPods, you can reset this iPod by first toggling the hold switch on and off and then simultaneously pressing the select (center) and menu buttons for approximately 5-10 seconds. This is a common fix should your iPod behave unexpectedly or lock up. Once reset, the iPod should display an Apple logo for a few seconds before showing the main menu. This procedure is similar to rebooting a computer and damages none of your music or data.

Since installing the new update videos keep on flickering when I stream them. How can I fix this?

Ever since I updated Firefox the videos I watch keep on flickering when I stream this. It is true of youtube, and other mediums. This is not a problem when I watch videos on Safari or Internet Explorer. I have uninstalled and reinstalled firefox to no success and restarting my computer has not helped either.

Hello, if the Flash player is not up to date, please update it, aslo:
Some problems with Flash video playback can be resolved by disabling hardware acceleration in your Flash Player settings. (See [[Flash Plugin - Keep it up to date and troubleshoot problems|this article]] for more information on using the Flash plugin in Firefox).
To disable hardware acceleration in Flash Player:
#Go to this [http://helpx.adobe.com/flash-player/kb/video-playback-issues.html#main_Solve_video_playback_issues Adobe Flash Player Help page].
#Right-click on the Flash Player logo on that page.
#Click on '''Settings''' in the context menu. The Adobe Flash Player Settings screen will open.
# Click on the icon at the bottom-left of the Adobe Flash Player Settings window to open the Display panel. <br/> <br/>[[Image:fpSettings1.PNG]] <br/>
# Remove the check mark from '''Enable hardware acceleration'''.
# Click '''Close''' to close the Adobe Flash Player Settings Window.
# Restart Firefox.
This [http://www.macromedia.com/support/documentation/en/flashplayer/help/help01.html Flash Player Help - Display Settings page] has more information on Flash Player hardware acceleration, if you're interested.
Does this solve the problem? Let us know.

Keeping display on when Docked

Similar Messages

Maybe you are looking for