Kernal Panics with CS2 and Bridge?

I have had the Mac Pro for two weeks.
This AM I sent it back to Apple for a new one.
From the day I took it out of the box I experienced
K.Panics. More so while in CS2 / Bridge.
Did an erase and install to no avail - ie. ruled
out software.
Anyone else having these types of issues with
CS2 and Bridge? On another note - while doing
nothing the machine is reallllly quiet, however,
once I start working on it the drive make a
sound like a subtle static, frying rice, etc.
Is this normal?
Many thanks.
Mac Pro   Mac OS X (10.4.7)  

Have installed 3rd party RAM or any other internal devices?
As for your drive noises… this is normal.

Similar Messages

  • Kernal Panic with Airport every few minutes

    For a few weeks now my MacBook Pro began to have kernal panics once every 3 or 4 days. These kernal panics always happened at home and almost never at work. At work I am always plugged into Ethernet and at home I connect via an Airport Snow base station - 802.11b. So I have read a few post talking about the same exact issue as mine. Last night I got to the point where my MBP had a kernal panic every minutes and eventualy started to get the kernal panics durning the apple boot screen (Grey apple logo on darker gray back round).
    So I booted into Safe Boot and then repaired permissions. I was able to do a normal boot after that however I did kernal panic over and over every few minutes. So I decided to upgrade from 10.4.7 to 10.4.8. Before I did this I trashed my airport prefs and ran another repair on my disk permissions. The upgrade went well. I noticed that my boot time is about 30 seconds longer and about 15 degrees cooler - Based on Core Duo Temp .
    After work I turned on my MBP to test the airport and within about 20 seconds of sitting idle and not a single appliction open I got a Kernal panic...
    Is there somthing anyone can suggest. Something I haven't tried or maybe a work around until the issue is address in the next release of Mac OS X.
    I will post some of my panic log below which only goes back 5 days. Thanks in advance to anyone who can help. My next step is to call Apple but I thought this forum would be faster.
    Wed Oct 11 06:09:16 2006
    panic(cpu 0 caller 0x0019CADF): Unresolved kernel trap (CPU 0, Type 14=page fault), registers:
    CR0: 0x80010033, CR2: 0x00000020, CR3: 0x00da7000, CR4: 0x000006e0
    EAX: 0x00000001, EBX: 0x0001d000, ECX: 0x02dd4140, EDX: 0x02ca0e00
    ESP: 0x00000020, EBP: 0x13bcbe28, ESI: 0x00000000, EDI: 0x02ca0e00
    EFL: 0x00010297, EIP: 0x00160c37, CS: 0x00000008, DS: 0x13bc0010
    Backtrace, Format - Frame : Return Address (4 potential args on stack)
    0x13bcbc78 : 0x128b5e (0x3bc46c 0x13bcbc9c 0x131bbc 0x0)
    0x13bcbcb8 : 0x19cadf (0x3c18e4 0x0 0xe 0x3c169c)
    0x13bcbd68 : 0x197c7d (0x13bcbd7c 0x13bcbe28 0x160c37 0x150048)
    0x13bcbd74 : 0x160c37 (0x150048 0x2ca0010 0x10010 0x13bc0010)
    0x13bcbe28 : 0x161338 (0x174b5000 0x0 0x3020d48 0x1d000)
    0x13bcbf78 : 0x19c5c6 (0x12ce708 0x174b5000 0x0 0x3)
    0x13bcbfd8 : 0x197bbb (0x2dd43b8 0x2dd43b8 0x1d000 0x20) No mapping exists for frame pointer
    Backtrace terminated-invalid frame pointer 0xb0220298
    Kernel version:
    Darwin Kernel Version 8.7.1: Wed Jun 7 16:19:56 PDT 2006; root:xnu-792.9.72.obj~2/RELEASE_I386
    Thu Oct 12 09:11:48 2006
    panic(cpu 0 caller 0x0019CADF): Unresolved kernel trap (CPU 0, Type 14=page fault), registers:
    CR0: 0x80010033, CR2: 0x00000020, CR3: 0x00db6000, CR4: 0x000006e0
    EAX: 0x00000001, EBX: 0x00035000, ECX: 0x02de2140, EDX: 0x02957c00
    ESP: 0x00000020, EBP: 0x13e03e28, ESI: 0x00000000, EDI: 0x02957c00
    EFL: 0x00010293, EIP: 0x00160c37, CS: 0x00000008, DS: 0x13e00010
    Backtrace, Format - Frame : Return Address (4 potential args on stack)
    0x13e03c78 : 0x128b5e (0x3bc46c 0x13e03c9c 0x131bbc 0x0)
    0x13e03cb8 : 0x19cadf (0x3c18e4 0x0 0xe 0x3c169c)
    0x13e03d68 : 0x197c7d (0x13e03d7c 0x13e03e28 0x160c37 0x150048)
    0x13e03d74 : 0x160c37 (0x150048 0x2950010 0x60010 0x13e00010)
    0x13e03e28 : 0x161338 (0x35000 0x0 0x26522a8 0x35000)
    0x13e03f78 : 0x19c5c6 (0x2c66f9c 0x35000 0x0 0x5)
    0x13e03fd8 : 0x197bbb (0x2de23b8 0x2de23b8 0x35000 0x20) No mapping exists for frame pointer
    Backtrace terminated-invalid frame pointer 0xbffffc78
    Kernel version:
    Darwin Kernel Version 8.7.1: Wed Jun 7 16:19:56 PDT 2006; root:xnu-792.9.72.obj~2/RELEASE_I386
    Sun Oct 15 21:58:18 2006
    panic(cpu 0 caller 0x00190357): pmapflushtlbs() timeout pmap=0x49a680 cpustosignal=0x2
    Backtrace, Format - Frame : Return Address (4 potential args on stack)
    0x13b9b3a8 : 0x128b5e (0x3bc46c 0x13b9b3cc 0x131bbc 0x0)
    0x13b9b3e8 : 0x190357 (0x3bf6b0 0x49a680 0x2 0x19caf2)
    0x13b9b438 : 0x191d42 (0x49a680 0x1df41000 0x0 0x0)
    0x13b9b488 : 0x173ef8 (0x8c16 0x0 0x2 0x0)
    0x13b9b518 : 0x1683ac (0x3214880 0x0 0x0 0x1000)
    0x13b9b608 : 0x1688db (0x1df42000 0x0 0x0 0x0)
    0x13b9b648 : 0x18348b (0x12ddb54 0x1df41000 0x0 0x1df42000)
    0x13b9b678 : 0x395f11 (0x12ddb54 0x1df41000 0x1000 0x1000)
    0x13b9b6b8 : 0x396bf1 (0x2ccde00 0x12ddf3c 0x1df41000 0x1000)
    0x13b9b6e8 : 0x396cd1 (0x247f440 0x2adf800 0x1df41000 0x0)
    0x13b9b708 : 0x396ca8 (0x247f440 0x0 0x2 0x400)
    0x13b9b728 : 0x3af24d (0x247f440 0x0 0x0 0x806000)
    0x13b9b748 : 0x5dbc2f (0x247f440 0x2d73a00 0x0 0x40)
    0x13b9b7a8 : 0x5ddcd0 (0x2adf800 0x2d73a00 0x1 0x130)
    0x13b9bc88 : 0x5c28ab (0x2adf800 0x13b9bcf0 0x0 0x0)
    0x13b9bd18 : 0x3a1e39 (0x2adf800 0x1 0x13b9bd4c 0x13b9bd48) Backtrace continues...
    Kernel loadable modules in backtrace (with dependencies):
    com.apple.ATIRadeonX1000(4.3.2)@0x5ba000
    dependency: com.apple.iokit.IOPCIFamily(2.0)@0x581000
    dependency: com.apple.iokit.IOGraphicsFamily(1.4.3)@0x590000
    dependency: com.apple.iokit.IONDRVSupport(1.4.3)@0x5ab000
    Kernel version:
    Darwin Kernel Version 8.7.1: Wed Jun 7 16:19:56 PDT 2006; root:xnu-792.9.72.obj~2/RELEASE_I386
    Sun Oct 15 22:15:24 2006
    panic(cpu 0 caller 0x00190357): pmapflushtlbs() timeout pmap=0x49a680 cpustosignal=0x2
    Backtrace, Format - Frame : Return Address (4 potential args on stack)
    0x13d4b3a8 : 0x128b5e (0x3bc46c 0x13d4b3cc 0x131bbc 0x0)
    0x13d4b3e8 : 0x190357 (0x3bf6b0 0x49a680 0x2 0x19caf2)
    0x13d4b438 : 0x191d42 (0x49a680 0x1e125000 0x0 0x0)
    0x13d4b488 : 0x173ef8 (0x1c744 0x0 0x2 0x0)
    0x13d4b518 : 0x1683ac (0x31c8ee0 0x0 0x0 0x1000)
    0x13d4b608 : 0x1688db (0x1e126000 0x0 0x0 0x0)
    0x13d4b648 : 0x18348b (0x12ddb54 0x1e125000 0x0 0x1e126000)
    0x13d4b678 : 0x395f11 (0x12ddb54 0x1e125000 0x1000 0x1000)
    0x13d4b6b8 : 0x396bf1 (0x2c3e300 0x12ddf3c 0x1e125000 0x1000)
    0x13d4b6e8 : 0x396cd1 (0x28527c0 0x2ab4000 0x1e125000 0x0)
    0x13d4b708 : 0x396ca8 (0x28527c0 0x0 0x2 0x0)
    0x13d4b728 : 0x3af24d (0x28527c0 0x0 0x0 0x13cb000)
    0x13d4b748 : 0x5dbc2f (0x28527c0 0x2c64280 0x0 0x40)
    0x13d4b7a8 : 0x5ddcd0 (0x2ab4000 0x2c64280 0x1 0x388)
    0x13d4bc88 : 0x5c28ab (0x2ab4000 0x13d4bcf0 0x0 0x0)
    0x13d4bd18 : 0x3a1e39 (0x2ab4000 0x1 0x13d4bd4c 0x13d4bd48) Backtrace continues...
    Kernel loadable modules in backtrace (with dependencies):
    com.apple.ATIRadeonX1000(4.3.2)@0x5ba000
    dependency: com.apple.iokit.IOPCIFamily(2.0)@0x581000
    dependency: com.apple.iokit.IOGraphicsFamily(1.4.3)@0x590000
    dependency: com.apple.iokit.IONDRVSupport(1.4.3)@0x5ab000
    Kernel version:
    Darwin Kernel Version 8.7.1: Wed Jun 7 16:19:56 PDT 2006; root:xnu-792.9.72.obj~2/RELEASE_I386
    Sun Oct 15 22:34:06 2006
    panic(cpu 1 caller 0x00190357): pmapflushtlbs() timeout pmap=0x49a680 cpustosignal=0x1
    Backtrace, Format - Frame : Return Address (4 potential args on stack)
    0x145eba98 : 0x128b5e (0x3bc46c 0x145ebabc 0x131bbc 0x0)
    0x145ebad8 : 0x190357 (0x3bf6b0 0x49a680 0x1 0x18fb36)
    0x145ebb28 : 0x191f7e (0x49a680 0x2a625000 0xfe953128 0xfe953130)
    0x145ebb78 : 0x1683e1 (0x49a680 0x2a625000 0x0 0x2a626000)
    0x145ebc68 : 0x1688db (0x2a626000 0x0 0x1 0x0)
    0x145ebca8 : 0x163511 (0x1b72f3c 0x2a625000 0x0 0x2a626000)
    0x145ebcd8 : 0x3b4ea8 (0x1b72f3c 0x2a625000 0x1000 0x0)
    0x145ebcf8 : 0x3af17c (0x33fe1c0 0x0 0x1 0x3b659b)
    0x145ebd18 : 0x3af24d (0x33fe1c0 0x0 0x3568ac0 0x41)
    0x145ebd38 : 0x3a550c (0x33fe1c0 0x2a625000 0x0 0x41)
    0x145ebd98 : 0x1894c5 (0x3049f00 0x380d1bc 0x2e454b4 0x2e454c8)
    0x145ebdd8 : 0x12b389 (0x380d194 0x2e45498 0x0 0x0)
    0x145ebe18 : 0x124902 (0x380d100 0x0 0x38 0x145ebefc)
    0x145ebf28 : 0x193034 (0x145ebf54 0x0 0x0 0x0)
    0x145ebfd8 : 0x19814b (0x2eb9318 0x2eb9318 0x134aec 0x145ebfe4) No mapping exists for frame pointer
    Backtrace terminated-invalid frame pointer 0xbffff6c8
    Kernel version:
    Darwin Kernel Version 8.7.1: Wed Jun 7 16:19:56 PDT 2006; root:xnu-792.9.72.obj~2/RELEASE_I386
    Sun Oct 15 23:00:55 2006
    panic(cpu 0 caller 0x00190357): pmapflushtlbs() timeout pmap=0x49a680 cpustosignal=0x2
    Backtrace, Format - Frame : Return Address (4 potential args on stack)
    0x13d3b568 : 0x128b5e (0x3bc46c 0x13d3b58c 0x131bbc 0x0)
    0x13d3b5a8 : 0x190357 (0x3bf6b0 0x49a680 0x2 0x18fb36)
    0x13d3b5f8 : 0x191f7e (0x49a680 0x29cf3000 0xfe94e798 0xfe94e7a8)
    0x13d3b648 : 0x1683e1 (0x49a680 0x29cf3000 0x0 0x29cf5000)
    0x13d3b738 : 0x1688db (0x29cf5000 0x0 0x1 0x0)
    0x13d3b778 : 0x163511 (0x12a0f3c 0x29cf3000 0x0 0x29cf5000)
    0x13d3b7a8 : 0x1b5f7a (0x12a0f3c 0x29cf3000 0x2000 0x19caf2)
    0x13d3b818 : 0x1b642d (0x2598e70 0x2000 0x13d3b848 0x2e666e)
    0x13d3b8a8 : 0x1b6862 (0x2598e70 0x2f58 0x0 0x2000)
    0x13d3b8e8 : 0x1b6ac1 (0x2000 0x0 0x0 0x10)
    0x13d3b908 : 0x2e01cc (0x2598e70 0x2f58 0x0 0x2000)
    0x13d3b978 : 0x309c76 (0x2598e70 0x2f58 0x0 0x13d3b9dc)
    0x13d3b998 : 0x30aa29 (0x25a5984 0x2f58 0x13d3b9dc 0x13d3b9f8)
    0x13d3ba18 : 0x308502 (0x25a5984 0x2b9882c 0x13d3ba44 0x13d3bae0)
    0x13d3bb08 : 0x2e3e58 (0x25edee0 0x2b98810 0x0 0x0)
    0x13d3bca8 : 0x30052b (0x256c404 0x1 0x2655da4 0x13d3bf04) Backtrace continues...
    Kernel version:
    Darwin Kernel Version 8.7.1: Wed Jun 7 16:19:56 PDT 2006; root:xnu-792.9.72.obj~2/RELEASE_I386
    Mon Oct 16 06:32:23 2006
    panic(cpu 1 caller 0x00190357): pmapflushtlbs() timeout pmap=0x49a680 cpustosignal=0x1
    Backtrace, Format - Frame : Return Address (4 potential args on stack)
    0x13d93a98 : 0x128b5e (0x3bc46c 0x13d93abc 0x131bbc 0x0)
    0x13d93ad8 : 0x190357 (0x3bf6b0 0x49a680 0x1 0x18fb36)
    0x13d93b28 : 0x191f7e (0x49a680 0x400e4000 0xfea00720 0xfea00728)
    0x13d93b78 : 0x1683e1 (0x49a680 0x400e4000 0x0 0x400e5000)
    0x13d93c68 : 0x1688db (0x400e5000 0x0 0x1 0x0)
    0x13d93ca8 : 0x163511 (0x12a9f3c 0x400e4000 0x0 0x400e5000)
    0x13d93cd8 : 0x3b4ea8 (0x12a9f3c 0x400e4000 0x1000 0x0)
    0x13d93cf8 : 0x3af17c (0x2690c80 0x0 0x1 0x3aff5d)
    0x13d93d18 : 0x3af24d (0x2690c80 0x0 0x13d93d68 0x17)
    0x13d93d38 : 0x3a550c (0x2690c80 0x400e4000 0x0 0x17)
    0x13d93d98 : 0x1894c5 (0x23e2de0 0x29587bc 0x2958db4 0x2958dc8)
    0x13d93dd8 : 0x12b389 (0x2958794 0x2958d98 0x0 0x0)
    0x13d93e18 : 0x124902 (0x2958700 0x0 0x38 0x13d93efc)
    0x13d93f28 : 0x193034 (0x13d93f54 0x0 0x0 0x0)
    0x13d93fd8 : 0x19814b (0x23dbf90 0x23dbf90 0x23ef3000 0x13d93b8c) No mapping exists for frame pointer
    Backtrace terminated-invalid frame pointer 0xbffff688
    Kernel version:
    Darwin Kernel Version 8.7.1: Wed Jun 7 16:19:56 PDT 2006; root:xnu-792.9.72.obj~2/RELEASE_I386
    Mon Oct 16 16:46:10 2006
    panic(cpu 0 caller 0x001914A1): pmapflushtlbs() timeout pmap=0x4af700 cpustosignal=0x2
    Backtrace, Format - Frame : Return Address (4 potential args on stack)
    0x13ecbb58 : 0x128d1f (0x3c9540 0x13ecbb7c 0x131df4 0x0)
    0x13ecbb98 : 0x1914a1 (0x3cc740 0x4af700 0x2 0x19065d)
    0x13ecbc08 : 0x1937d4 (0xfe9ffda0 0xfe9ffdb0 0x0 0x19a3a6)
    0x13ecbc58 : 0x165355 (0x4af700 0x3ffb4000 0x0 0x3ffb6000)
    0x13ecbd48 : 0x165b09 (0x3ffb6000 0x0 0x1 0x0)
    0x13ecbd88 : 0x162e18 (0x12c5f3c 0x3ffb4000 0x0 0x3ffb6000)
    0x13ecbdb8 : 0x15c252 (0x12c5f3c 0x3ffb4000 0x141c 0x0)
    0x13ecbdf8 : 0x160c5b (0x2c8e600 0x0 0x2dd7e58 0x6f000)
    0x13ecbf48 : 0x1a33a8 (0x2c2d658 0xb01f3000 0x0 0x3)
    0x13ecbfc8 : 0x19a804 (0x2d06c9c 0x1 0x19d0b5 0x2d06080) No mapping exists for frame pointer
    Backtrace terminated-invalid frame pointer 0xb01f42f8
    Kernel version:
    Darwin Kernel Version 8.8.1: Mon Sep 25 19:42:00 PDT 2006; root:xnu-792.13.8.obj~1/RELEASE_I386
    I

    Got panic with brand new MacBook Pro Core 2 Duo:
    Machine Model: MacBookPro2,2
    Processor Name: Intel Core 2 Duo
    Processor Speed: 2.33 GHz
    Number Of Processors: 1
    Total Number Of Cores: 2
    L2 Cache (per processor): 4 MB
    Memory: 2 GB
    Bus Speed: 667 MHz
    Boot ROM Version: MBP22.00A5.B00
    SMC Version: 1.12f5
    Panic details:
    Sun Dec 10 22:14:35 2006
    panic(cpu 1 caller 0x001A3135): Unresolved kernel trap (CPU 1, Type 14=page fault), registers:
    CR0: 0x8001003b, CR2: 0x00000000, CR3: 0x00f25000, CR4: 0x000006e0
    EAX: 0x00000007, EBX: 0x23770308, ECX: 0x00000000, EDX: 0x00000010
    CR2: 0x00000000, EBP: 0x2543b688, ESI: 0x23770d74, EDI: 0x00000000
    EFL: 0x00010202, EIP: 0x00a0dd80, CS: 0x00000008, DS: 0x00000010
    Backtrace, Format - Frame : Return Address (4 potential args on stack)
    0x2543b448 : 0x128d08 (0x3c9afc 0x2543b46c 0x131de5 0x0)
    0x2543b488 : 0x1a3135 (0x3cf7b0 0x1 0xe 0x3cefe0)
    0x2543b598 : 0x19a904 (0x2543b5b0 0x23770308 0x2543b5e8 0x127e77)
    0x2543b688 : 0xa0df71 (0x23770d74 0x23770308 0x2543b7e8 0x0)
    0x2543b6a8 : 0xa0e231 (0x23907004 0xc0a00071 0x40 0x0)
    0x2543b808 : 0xa1e4f1 (0x23770308 0x1 0x2543b838 0x3bbd7c)
    0x2543b858 : 0x9d858e (0x23770000 0x3e8ce00 0x2543b8ac 0x2543b898)
    0x2543bc98 : 0x399892 (0x23770000 0xc 0x4999ec1 0x0)
    0x2543bcd8 : 0x9d6e84 (0x3d34340 0x9d7aae 0xc 0x4999ec1)
    0x2543bd18 : 0x3b0db0 (0x23770000 0xc 0x4999ec1 0x0)
    0x2543bd68 : 0x18a18e (0x416bb00 0x0 0x4999ec0 0x5)
    0x2543bdb8 : 0x12b4c3 (0x4999e98 0x453056c 0x0 0x0)
    0x2543bdf8 : 0x124b17 (0x4999e00 0x0 0x34 0x2543bedc)
    0x2543bf08 : 0x1955a8 (0x2543bf44 0x0 0x0 0x0)
    0x2543bfc8 : 0x19ad7e (0x3e69b20 0x0 0x10 0x3894c00) No mapping exists for frame pointer
    Backtrace terminated-invalid frame pointer 0xbfffe278
    Kernel loadable modules in backtrace (with dependencies):
    com.apple.driver.AirPortAtheros(210.8)@0x9ea000
    dependency: com.apple.iokit.IONetworkingFamily(1.5.1)@0x6c1000
    dependency: com.apple.iokit.IOPCIFamily(2.2)@0x59b000
    dependency: com.apple.iokit.IO80211Family(140.4)@0x9ce000
    com.apple.iokit.IO80211Family(140.4)@0x9ce000
    dependency: com.apple.iokit.IONetworkingFamily(1.5.1)@0x6c1000
    dependency: com.apple.iokit.IOPCIFamily(2.2)@0x59b000
    Kernel version:
    Darwin Kernel Version 8.8.2: Thu Sep 28 20:43:26 PDT 2006; root:xnu-792.14.14.obj~1/RELEASE_I386
    No updates available for this machine, so I'm not sure what to do. Panic never occurs at home, only at work. And only after moving to a new office. The big difference is that I many more WLANs at the new location. Perhaps its the amount of them, or one specific that the AirPort cannot handle properly. Waiting for apple patch ....
    MacBook Pro   Mac OS X (10.4.8)  

  • Kernal panic with software install and restore disc

    I'm trying to access my software install and restore disc for my powerbook G4 running tiger. Everytime I restart the computer with the disc in, and hold down c, I get a kernal panic. There is nothing wrong with the software install and restore disc, as far as I can tell.
    Thanks for any help!
    Powerbook G4   Mac OS X (10.4.6)  

    is this a tiger disk or a previous operating system? if it is a previous os restore disk, then it is not surprising it would panic. the only software restore disks you would need would be ones to run the apple hardware test and to install or reinstall os 9. otherwise, you should not use a software restore disk for a previous operating system, unless you have erased and installed your drive. [ 8 ) ]

  • Kernal panic with install disk

    Hello.
    I've successfully used my SL install disk to launch Utilities on my G5 and switch Firmware Password on, so I know that the DVD is OK - it's the Apple original. When I try on my MBP, the boot repeatedly stalls on the gray Apple screen then gives me a kernal panic message to switch off. The install disk mounts OK when I've booted from the HD but won't restart from the disk. They are both running SL 10.6.7 with everything up to date. The MBP works fine in every other respect but I can't set a firmware password on it.
    Thanks.

    Sorry, did I get the name of my Mac wrong?
    Model Name: iMac
      Model Identifier: iMac8,1
      Processor Name: Intel Core 2 Duo
      Processor Speed: 3.06 GHz
      Number Of Processors: 1
      Total Number Of Cores: 2
      L2 Cache: 6 MB
      Memory: 4 GB
      Bus Speed: 1.07 GHz
    The disk is Apple retail.

  • Kernal panic with OS X update

    Hi all, I have a kernal panic on my MBP and have tried several things to fix it without success.
    I was updating to OS X 10.5.8 via download, and after I restarted my computer as instructed, the computer shut down at approx 75% of installation. Since then I have been getting the kernal panic message with every restart. The issue continues even in Safe Mode.
    The kernal panic is as follows:
    panic(cpu 0 caller0x001AC125): Version mismatch between Kernel and CPU PM"!/SourceCache/xnu/xnu-1228.15.4/osfmk/i386.pmCPU.c:651
    Debugger called: <panic>
    further down it says:
    Mac OS version:
    Not yet set
    1.83Ghz, 2GB RAM (installed after market, but several years ago)
    available: 6.51 GB total: 74.21 GB
    Bus speed: 667 MHz
    I tried to Archive and re-install OS X but don't have enough available memory. I can't erase and re-install at this point unless I absolutely have to.
    I'm at a loss as to what to do at this point. Any help would be great.

    This can be caused by having a dysfunctional system prior to updating. The usual solution is to reinstall OS X. If you haven't enough disk space to do an Archive and Install, then you have the added problem of not having sufficient free space for OS X. I would suggest you get an external hard drive on which you can backup your files. Get a larger hard drive for your omputer or look for ways to store more of your personal data on an external drive in order to free up space on the hard drive. Then erase the hard drive and reinstall OS X.

  • Sudden Kernal Panics with Production Server

    I was called in today because a departmental supervisor had to manually restart their production server today and the application that ran on it didn't restart properly. After some looking and then another controlled restart to get the application going again, the server kernal paniced. From actualy examination, it appears this is what happened the first time.
    As the server is in production mode, I've not taken any steps with Dr. Smoke's troubleshooting list, but I have pulled the panic.log and I'm posting it here. If someone has any clue where I should start, that would be helpful!
    Wed Nov 16 13:58:32 2005
    panic(cpu 0 caller 0x000E7FF4): vnode_put(1d95210): iocount < 1
    Latest stack backtrace for cpu 0:
    Backtrace:
    0x00095698 0x00095BB0 0x0002683C 0x000E7FF4 0x000E7FA0 0x000D4A18 0x002A9BF4 0x000ABE30
    0xFF5DB3C2
    Proceeding back via exception chain:
    Exception state (sv=0x2F8F6280)
    PC=0x9001C240; MSR=0x0000F030; DAR=0xE0E9CB38; DSISR=0x02200000; LR=0x90B14554; R1=0xF1425710; XCP=0x00000030 (0xC00 - System call)
    Kernel version:
    Darwin Kernel Version 8.3.0: Mon Oct 3 20:04:04 PDT 2005; root:xnu-792.6.22.obj~2/RELEASE_PPC
    Could this be a processor flaking out? I'm sure I'll have to do this after hours, so any head start I can get would be greatly appreciated!
    PowerBook G4 17   Mac OS X (10.3.9)   1.5G RAM

    Hi, L.
    The panic cited, i.e.
    panic(cpu 0 caller 0x000E7FF4): vnode_put(1d95210): iocount < 1</tt>
    implies something is amiss either with affected Mac's hard drive directory (potentially affecting either file information or virtual memory swap files) or your RAM. Processor or programming errors are also possible, but I'd say less likely.
    A vnode is defined here as "An in-memory data structure containing information about a file."
    The particular message sited in the panic comes from the vfs_subr.c component of the operating system, concerned with "External virtual filesystem routines."
    I suggest you troubleshoot this off-hours using my "Resolving Kernel Panics" FAQ, as you noted. This FAQ includes step-by-step instructions for identifying and resolving some of the most common causes of kernel panics.
    My FAQ is a roadmap: start at the beginning and work through to the end, following the instruction in the order specified, including the "If all else fails..." section if a cause or resolution is not found in an earlier troubleshooting step therein.
    If you look at this Google search you'll find some similar reports that find issues with hard drive files, RAM, bad NIC, and related things that the troubleshooting steps in my FAQ would help you isolate. However, follow my FAQ step-by-step rather than skipping around as it's designed to find high-probability / low-effort causes up front.
    Good luck!
    Dr. Smoke
    Author: Troubleshooting Mac® OS X
    Note: The information provided in the link(s) above is freely available. However, because I own The X Lab™, a commercial Web site to which some of these links point, the Apple Discussions Terms of Use require I include the following disclosure statement with this post:
    I may receive some form of compensation, financial or otherwise, from my recommendation or link.

  • Kernal Panic on Netinstall and Netrestore

    Hi All
    I have been using system image utility as per what apple state you should do for mavericks, and it  its a easy process to create the netinstall and restore, on the server it shows that it is active and working but when i try boot into it the machine kernal panics and just restarts ? what am i doing wrong please help
    Thanks

    as piperspace is saying, you need to look carefully at the Installer on which you based this image.
    An Installer that "shipped in the box" with a Mac has Drivers for only that model Mac, and no others. There is no way to "improve" it to add the other Drivers.
    An Installer that you bought, even for $0 (we used to call it a "Full Retail") contains "Drivers for every appropriate model Mac."

  • Problem with CS2 and firefox 3.6x

    i have a strange problem arising from a combination of photoshop cs2 and firefox 3.6x browser in XP sp3
    when photoshop is minimised to the taskbar and then firefox is minimised, the focus of firefox seems to be passed to photoshop unexpectedly, turning its button dark blue and making it very difficult to maximise photoshop (repeated clicking and swapping of apps sometimes frees it)
    has anyone else every experienced anything like this with 3.6?
    i have installed 3.5.10 atm which works with no problem at all and holds its own focus when minimised.
    Steve

    None of those ideas worked. I used the Disk Utility and it indicated that all permissions were OK. I cleared the caches and cookies on Safari and FireFox, and even re-installed FireFox and deleted all of the old files associated with it. Both browsers brought up the Apple support website using the IP address, but neither browser would allow me to log into Apple support to follow this thread. I turned off the Firewall thinking it was the problem. I am running the PC and iMac through a router, then a dsl modem. Could any of those items be the problem?

  • Kernal Panic with OS 10.4.6 install

    Repeated attempts to install OS 10.4.6 over 10.2.8 each time resulted in kernal panic. Despite restarting from outboard Firewire HD and using Disk Repair to correct permissions and repair the Macintosh HD, no joy followed. TechTool Deluxe 3.0.3 reported no HD problems. Taking the CPU to the MAC Store resulted in a successful install by the technician who repaired permissions and severe directory damage. Happily, I reconnected all previous cables at home, started up the MAC, and immediately noted the return of kernal panic or, finally, the MAC Blue Screen of Death. Disconnecting the SCSI cable (connected to Adaptec SCSI Card 2906) from an Iomega Zip Drive resolved the problem. I should have known that the SCSI device could be the cause of this problem, but I missed seeing the other reports in the Installation & Setup section when searching the terms “kernal panic.”
    Entering “SCSI” as a search term does produce numerous messages regarding incompatibility problems, such as this long chain, “No luck getting Adaptec 2906 SCSI card to work.”
    PowerMac 867 MHz   Mac OS X (10.4.6)   RAM: 256MH then >> 768 MH now

    J.Michael:
    Kernel panics are usually hardware based. If you have recently installed RAM or a peripheral your problem may be related to that piece of hardware.
    Check out Dr. Smoke's Resolving Kernel Panics and see if there are any clues for you in it.
    Good luck.
    cornelius

  • Compatibility Issues with CS2 and Windows 2000 XP??? This is supposed to be THE one operating system CS2 DOES WORK ON? Can someone help - I really need my CS2 back! Thanks.

    HELP! Years ago - SEVEN to be exact- I PURCHASED Adobe CS2 and used it extensively. Then I was in an accident that took five years to recover from. After my recovery I tried to get back to using my Adobe products only to find that Adobe was discouraging use of CS2 and since I OWN a LICENSE and that was the LAST version I used I wanted to begin again with a version I am familiar with. Many months later, apparently I wasn't the only one who wanted to KEEP USING CS2 and now Adobe has made it possible to download this version for PC and MAC, BUT due to OS compatibility issues Adobe continues to discourage downloading and use. HERE'S THE THING: I have the SAME SYSTEM running the SAME OS as when I first PURCHASED IT. I have downloaded the EXACT SAME VERSION of CS2. It installs fine. But I cannot OPEN the application and the troubleshooter reports there are "COMPATIBILITY ISSUES". WHY?!?!?!?!?
    I'm on a PC running Windows 2000 XP. I OWN a LICENSE for Adobe CS2 and it used to run on this very same machine. I had to re-format my system two years ago so it has much more free space but when I  try to OPEN the application it won't run. When I run the Windows Troubleshooter it reports system compatibility issues?! Can anyone advise me what to try now??? Thank you.

    Yes, I have. My system was completely cleaned of everything and I'm just now RE-INSTALLING CS2 for Windows2000 XP from the Adobe site that gives you versions to select for your OS. I have successfully downloaded disks 1,2 and 3 and I can INSTALL disks 1 and 2, but it FAILS at disk 3. I REALLY need to resolve this today because I need to submit some work by tomorrow and the troubleshooting isn't helping!
    Can you advise anything else . . . anyone? Thank you!
    Khrystle13

  • Working with Lightroom and Bridge

    I have been using Lightroom for my photos, but was thinking of doing the following:
    - Use Bridge to import files, and sort and tag them
    - This has the benefit of allowing me to categorize movies, etc.
    - Then open and use Lightroom for editing, etc.
    Q1: LR is non-destructive. If I add a tag to an image in Bridge, does that write it to the file? Is it non-destructive.
    Q2: If I import files into Bridge, do I open LR and import them in there too, or can I simply share the photos between the 2 programs?
    Q3: Does LR read the keyword tags from Bridge?
    Thoughts?
    Thanks...
    John

    I use Bridge exclusively for culling, editing, keywording. It is faster at those tasks, since it does not require importing everything into a database in order to edit them and then export them. I also already have a DAM that I presently prefer to LR, and likewise for slide shows and printing. I do maintain a 20,000 image test catalog in LR so that I can thoroughly test each of its trial versions, so I am very familiar with it from the first Beta testing to the present.
    As long as you write your metadata to sidecars--or directly to tif and jpeg files, or DNG-- both Bridge and LR can see the changes made in either. However, if after you have imported files into the LR Library--and you must do that in order to use any of the features of LR on images--and subsequently delete them, then you must synchronize the folder they are in(lightroom menu item)to clear those image references from Lightrooom's Library. Same goes for adding files to a folder from outside of LR. There are a few things you must remember to do. It is not an entirely automatic process.
    If you do a lot of work in PS on your images, you will likely find that working in Bridge with its very fast connection to PS will be faster. If you also do a lot of video--or mixed video,graphics, and image work, you are also likely to find Bridge faster and more workflow effective. LR is strictly a Photographic image management and editing application, from which you can do basic printing, very basic slideshows, and web work.
    On the other hand, if you do little editing beyond what ACR provides (same features as LR) and need a DAM that manages only photographic images, and you find the LR Print, web and slideshow features satsifactory, then LR will overall be the more effective workflow.
    The only way to determine which is right for you is to give your workflow a thorough test with LR and compare that to Bridge. LR 2.3 appears to be free of significant bugs, is fast and smooth, so this would is a good time for comparison. Bridge CS4/ACR 5.3 have been significantly upgraded as well, as you know. Workflows differ, sometimes significantly, as do machine configurations, so thorough individual testing is a must. Use the tools that will do the best job for your requirements.

  • Problems opening and saving PNG over network with CS2 and CS3

    using os10.4.11
    photoshop CS2 or CS3
    I've recently tried to save images in PNG format,  small (no more than a couple hundred kilobytes) and found that whenever I tried to save to the server it would hang photoshop and require a force-quit. Saving the same file to the desktop works fine. Copying said file to the network and then trying to open that PNG from the server results in a photoshop hang, while opening that same file from the desktop works fine. I know all about the fact that Adobe doesn't support working over a server, but that's never been an issue at my workplace in all the years I've worked with (never had problems saving/opening any format, no corrupted files ever). If I try to open that same PNG from the server with CS2, same result. If I try to open it over the server using Photoshop CS, or version 7, however, it opens just fine. If I copy the Photoshop CS version of the PNG plugin and replace the PNG plugin installed with CS3 by default, then it seems to work and I can now open and save PNGs anywhere with no problems. Has anyone else had this problem? I can see that the file size of the PNG plugin has changed version to version, so something about it has changed. It seems as though there is something defective about the ones installed with CS2/3, and just copying the CS version into my CS3 folder clears up the problem.
    Also, the problem is not limited to my computer. Other macs that try to open PNG files from the server using CS3 or 2 also hang.

    Yes, we're a prepress company moving around probably a few dozen gb of data per day, saving PSD, TIFF, EPS, JPEG, all kinds of formats. It's the first time I've had a client requesting PNG files, and so the issue has come to light. This is the first time I've ever seen any kind of issue opening/saving across our network in 8 years. (the only time I've ever seen a corrupt file was a 1.6gb image that didn't copy correctly, and that wasn't a photoshop-related corruption, but an OS drag/copy of the file)
    I'm not sure if I'll be able to find someone with OS 10.5 or some other version to see if they cause problems. If anyone else reading this who works over a network can test a PNG open/save over their network and list their OS and Photoshop version it may help. I'm going to see if I can find some other computers to try it out on in the meantime and mention it to IT.

  • Kernal panic with hotmail use

    EVERYTIME I open my hotmail account through safari OR firefox within 1 minute a kernal panic occurs and I am forced to restart my computer. We have had this computer for about 4 years and never had this problem. I don't understand how this can be a hardware problem because it only involves one website...so far. Anyway to determine or fix this problem?
    We run a MAC OS X 10.4.11
    I have run all updates.

    At this point I think you should get Applejack...
    http://www.versiontracker.com/dyn/moreinfo/macosx/19596
    http://www.macupdate.com/info.php/id/15667
    After installing, Reboot holding down CMD+s, (+s), then when the DOS like prompt shows, type in...
    applejack AUTO
    Then let it do all 5 of it's things.
    The 5 things it does are...
    Correct any Disk problems.
    Repair Permissions.
    Clear out Cache Files.
    Repair/check several plist files.
    Dump the VM files for a fresh start.
    At least if it doesn't fix it, it'll eliminate a few questions.

  • Kernal Panic with Mountain Lion

    Hello everyone,
    During these past few days I have been having the so called 'kernal panics' on my 2010 mbp i7. From reading other threads, I can tell you that its definitely not the Nvidia GPU that is not functioning, as I bootcamp and use the very same GPU to play my window games. I am now going to paste you the log report of the latest panic. The panic before this panic was almost 2 days, so I thought the issue is fixed and it comes back. I do note that the log seems to be shorter than usual.
    Interval Since Last Panic Report:  24416 sec
    Panics Since Last Report:          2
    Anonymous UUID:                    A22A6FCE-EE79-3A72-AD0B-E7C2523EF826
    Thu Oct  4 11:15:44 2012
    panic(cpu 1 caller 0xffffff7f83848b25): NVRM[0/1:0:0]: Read Error 0x00000100: CFG 0xffffffff 0xffffffff 0xffffffff, BAR0 0xd2000000 0xffffff80a217c000 0x0a5480a2, D0, P2/4
    Backtrace (CPU 1), Frame : Return Address
    0xffffff807e7d2f80 : 0xffffff800301d626
    0xffffff807e7d2ff0 : 0xffffff7f83848b25
    0xffffff807e7d3080 : 0xffffff7f839424b3
    0xffffff807e7d30e0 : 0xffffff7f83942527
    0xffffff807e7d3150 : 0xffffff7f83c57853
    0xffffff807e7d3290 : 0xffffff7f83968659
    0xffffff807e7d32c0 : 0xffffff7f838528da
    0xffffff807e7d3370 : 0xffffff7f8384dfac
    0xffffff807e7d3560 : 0xffffff7f8384f1d8
    0xffffff807e7d3630 : 0xffffff7f8489f45e
    0xffffff807e7d36f0 : 0xffffff7f848d000f
    0xffffff807e7d3770 : 0xffffff7f848b4b4a
    0xffffff807e7d37d0 : 0xffffff7f848b5415
    0xffffff807e7d3820 : 0xffffff7f848b580f
    0xffffff807e7d38c0 : 0xffffff7f848b6239
    0xffffff807e7d3900 : 0xffffff7f84871e81
    0xffffff807e7d3a80 : 0xffffff7f848b27fe
    0xffffff807e7d3b40 : 0xffffff7f8487098a
    0xffffff807e7d3ba0 : 0xffffff8003465bc9
    0xffffff807e7d3bc0 : 0xffffff8003467170
    0xffffff807e7d3c20 : 0xffffff8003464b8f
    0xffffff807e7d3d70 : 0xffffff80030981e1
    0xffffff807e7d3e80 : 0xffffff8003020aed
    0xffffff807e7d3eb0 : 0xffffff8003010448
    0xffffff807e7d3f00 : 0xffffff800301961b
    0xffffff807e7d3f70 : 0xffffff80030a5b16
    0xffffff807e7d3fb0 : 0xffffff80030ced53
          Kernel Extensions in backtrace:
             com.apple.NVDAResman(8.0)[A4C53A36-22B6-3075-82B9-9DE612A9C015]@0xffffff7f837e1 000->0xffffff7f83ae3fff
                dependency: com.apple.iokit.IOPCIFamily(2.7.1)[9901C237-547C-3B52-99DE-C4870A19E2B5]@0xffff ff7f8357c000
                dependency: com.apple.iokit.IONDRVSupport(2.3.5)[86DDB71C-A73A-3EBE-AC44-0BC9A38B9A44]@0xff ffff7f837cd000
                dependency: com.apple.iokit.IOGraphicsFamily(2.3.5)[803496D0-ADAD-3ADB-B071-8A0A197DA53D]@0 xffffff7f8378a000
             com.apple.nvidia.nv50hal(8.0)[9F3D09B5-3158-3D9E-BDA3-E71576AAD3B7]@0xffffff7f8 3af1000->0xffffff7f83e13fff
                dependency: com.apple.NVDAResman(8.0.0)[A4C53A36-22B6-3075-82B9-9DE612A9C015]@0xffffff7f837 e1000
                dependency: com.apple.iokit.IOPCIFamily(2.7.1)[9901C237-547C-3B52-99DE-C4870A19E2B5]@0xffff ff7f8357c000
             com.apple.GeForce(8.0)[2E56ED9A-D848-3795-9E52-56BABDC9000C]@0xffffff7f84864000 ->0xffffff7f84926fff
                dependency: com.apple.NVDAResman(8.0.0)[A4C53A36-22B6-3075-82B9-9DE612A9C015]@0xffffff7f837 e1000
                dependency: com.apple.iokit.IONDRVSupport(2.3.5)[86DDB71C-A73A-3EBE-AC44-0BC9A38B9A44]@0xff ffff7f837cd000
                dependency: com.apple.iokit.IOPCIFamily(2.7.1)[9901C237-547C-3B52-99DE-C4870A19E2B5]@0xffff ff7f8357c000
                de
    Model: MacBookPro6,2, BootROM MBP61.0057.B0F, 2 processors, Intel Core i7, 2.66 GHz, 4 GB, SMC 1.58f16
    Graphics: Intel HD Graphics, Intel HD Graphics, Built-In, 288 MB
    Graphics: NVIDIA GeForce GT 330M, NVIDIA GeForce GT 330M, PCIe, 512 MB
    Memory Module: BANK 0/DIMM0, 2 GB, DDR3, 1067 MHz, 0x80CE, 0x4D34373142353637334648302D4346382020
    Memory Module: BANK 1/DIMM0, 2 GB, DDR3, 1067 MHz, 0x80CE, 0x4D34373142353637334648302D4346382020
    AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x93), Broadcom BCM43xx 1.0 (5.106.98.81.22)
    Bluetooth: Version 4.0.9f33 10885, 2 service, 11 devices, 1 incoming serial ports
    Network Service: AirPort, AirPort, en1
    Serial ATA Device: TOSHIBA MK5055GSXF, 500.11 GB
    Serial ATA Device: MATSHITADVD-R   UJ-898
    USB Device: hub_device, 0x0424  (SMSC), 0x2514, 0xfa100000 / 2
    USB Device: USB Receiver, 0x046d  (Logitech Inc.), 0xc52b, 0xfa140000 / 6
    USB Device: BRCM2070 Hub, 0x0a5c  (Broadcom Corp.), 0x4500, 0xfa110000 / 5
    USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x8218, 0xfa113000 / 8
    USB Device: Apple Internal Keyboard / Trackpad, apple_vendor_id, 0x0236, 0xfa120000 / 4
    USB Device: Internal Memory Card Reader, apple_vendor_id, 0x8403, 0xfa130000 / 3
    USB Device: hub_device, 0x0424  (SMSC), 0x2514, 0xfd100000 / 2
    USB Device: Built-in iSight, apple_vendor_id, 0x8507, 0xfd110000 / 4
    USB Device: IR Receiver, apple_vendor_id, 0x8242, 0xfd120000 / 3
    It would be nice to receive some suggestions from you guys. Is it possible that it is the intel card that is broken?
    Thank you,
    Mek

    Frequent Panic NVRM[0/1:0:0]: Read...: Apple Support Communities
    MacBook Pro (15-inch, Mid 2010): Intermittent black screen or loss of video

  • Setting the layer name from a format plugin with CS2 and before

    Hello,
    I wrote a new format plugin and the name of the layer shown in PS , when I read a file, does not seem to be consistent on all computers for versions CS2 and before :  some times I get "Background" and some times I get "Layer 0" .
    When the layer is named is "Background",  it is locked. If I double click on the layer, I get a panel to rename it and the name suggested is "Layer 0" (and not "Background").
    Somehow, it seems that my plugin is not doing exactly the right thing or there is a setting in PS options (or in the registry) that controls/causes that behavior. My understanding is that we can't name layers from the plugin before version CS3 (setting the layerName field in the FormatRecord makes no difference for CS2 and before).
    I do not care much about the actual layer name as long as that name is consistent for all installations. Does anybody know what is going on?
    Thank you!
    Gilbert

    If it has transparency, it has to be a layer ("Layer0").
    If it doesn't have transparency, it is treated as a background.
    And yes, changing the background to a layer does normally rename it to "layer X".

Maybe you are looking for