Kernel Panic when booting to Tiger DVD

Subject line says it all. It's 2x2.5GHz G5 running 10.4.10. When I try to boot to the install DVD, I get a kernel panic. The drive works for things like installing apps, and the HD installation of Tiger boots fine, but no can boot from DVD. Is this a hardware issue?

I just dropped off my quad at the local Apple Authorized shop. Their tech took a look at my pic http://homepage.mac.com/chadself/.cv/chadself/Sites/.Public/G-MAc%20Kernal%20Pan ic%20200709281906.pdf-zip.zip of the panic screen and feels like it may be the logic board. Maybe it is. The system still will boot to my desktop and runs thoughstill feels slow and is a bit flakey. (Compressor still crashes before it can launch, iTunes occasionally hangs etc)
The Apple Care tech (very friendly and professional though having to repeat everything three times meant the diagnosis took much longer than necessary) had me remove all cables including power and hold power button for 20 seconds, plus run disk util, eventually gave up and sent me to repair center.
I'll let you know what they say. I can tell you that running FCP Studio off my laptop (even if it is a MBP with 2GB mem) is not nearly as productive.;)
Cheers!
Message was edited by: Chadwick

Similar Messages

Kernel panic when booting from Tiger install DVD

Short version: When I try to boot up from the Tiger installation DVD, my Power Mac G5 gives me a kernel panic. Can anyone help?
Here's the story:
I have a Power Mac G5 that I've been running Leopard on for quite some time now. Unfortunately, the software I need to use (Final Cut Studio 1) has some incompatibilities with Leopard, so I was thinking I would put Tiger back on the machine in a separate partition on the second hard drive.
I tried booting the Power Mac using the retail (black label) Tiger DVD and holding down the "C" key. The Apple logo appears on screen, but is immediately followed by a kernel panic. I'm never able to access the features on the disc. The same thing happens if I try holding down "option" during boot instead: I'm correctly allowed to choose whether to boot from the hard drive or the DVD, but once I choose the DVD, I get the Apple logo and then a kernel panic.
The same Tiger DVD works fine on other computers, so I know it's not the disc. And the Power Mac itself handles everything else without problem.
I'm kind of desperate, as I need to finish this project this week. Any help you could give would be greatly appreciated!

[Apple docs: What's a kernel panic? (Mac OS X)|http://docs.info.apple.com/article.html?artnum=106227]
[Topic : kmosx: Kernel Panics? Don't panic too !|http://discussions.apple.com/thread.jspa?threadID=121923]
[X-Lab: Resolving Kernel Panics|http://www.thexlab.com/faqs/kernelpanics.html]
[Tutorial: Avoiding and eliminating Kernel panics|http://www.macfixit.com/article.php?story=20060911080447777]
[Tutorial: An introduction to reading Mac OS X crash reports|http://www.macfixit.com/article.php?story=20060309075929717]
[12-Step Program to Isolate Freezes and/or Kernel Panics|http://macosg.com/group/viewtopic.php?t=800]

Kernel Panic When Booting with Install DVD

I get a kernel panic when booting from the OSX 4 (tiger) install DVD. I am using a Quad G-5 with 8 gigs of ram.

Have to ask what version your Quad came with, whether same DVD you are using now. Apple now has Tiger DVDs w/ 10.4.6 for sale.
When booting, or when you get to the screen to select Languages on the initial screen (before you can select DU or Installer etc)?
How about Option booting to Apple Hardware Test and running extended test?
Did you run memtest or anything when you installed RAM (assuming you didn't buy it BTO w/ 8GB).
Any time adding or changing hardware, including memory, it is either a good policy or essential in some cases to boot into Open Firmware (command option of) on startup and type "reset-nvram" and 'reset-all" after installing. Same for PCIe or even swapping out disk drive (where sometimes a drive won't show up or allow you to partition).

Kernel panic when booting from DVD or external drive

Hey Folks,
I have a 13" MBP, seems to run fine for the most part.
However, I can't boot from DVDs or external hard drives. Disk Warrior, my and a tech support buddy of mine's OSX Snow Leopard DVDs, and external boot disks all cause a kernel panic when selected from the alternate boot menu when rebooting with alt.
The DVD/External spins up, the loading spinner goes for about 20-30 seconds, and then BAM - Kernel panic. I'd reinstall OSX... but I can't!
Any suggestions? I'd rather not send the computer to a tech for a week - I need it daily for work.

Kernel panic log:
Fri Nov 26 11:42:49 2010
panic(cpu 0 caller 0x2a6ac2): Kernel trap at 0x00000000, type 14=page fault, registers:
CR0: 0x8001003b, CR2: 0x00000000, CR3: 0x00100000, CR4: 0x000006e8
EAX: 0x57cd9408, EBX: 0x57983dec, ECX: 0x06fa2b80, EDX: 0x07fb9c80
CR2: 0x00000000, EBP: 0x57983e18, ESI: 0x07fb9f00, EDI: 0x00000001
EFL: 0x00010206, EIP: 0x00000000, CS: 0x00000008, DS: 0x00000010
Error code: 0x00000010
Backtrace (CPU 0), Frame : Return Address (4 potential args on stack)
0x57983ae8 : 0x21acfa (0x5ce650 0x57983b1c 0x223156 0x0)
0x57983b38 : 0x2a6ac2 (0x590a50 0x0 0xe 0x590c1a)
0x57983c18 : 0x29c968 (0x57983c30 0x7fb9f00 0x57983e18 0x0)
0x57983c28 : 0x0 (0xe 0x48 0x57980010 0x7fb0010)
0x57983e18 : 0x5389f2 (0x7fb5a00 0x7f62500 0x1 0x4fbe2a)
0x57983e78 : 0x536c27 (0x7f62500 0x7fb5a00 0x8006380 0x805e4c0)
0x57983f28 : 0x5371b8 (0x7f62500 0x8000140 0x0 0xffffffff)
0x57983f78 : 0x538e67 (0x7f62500 0x0 0x57983fac 0x1)
0x57983fc8 : 0x29c68c (0x7f85190 0x0 0x29c69b 0x74d03d4)
BSD process name corresponding to current thread: kernel_task
Mac OS version:
10A432
Kernel version:
Darwin Kernel Version 10.0.0: Fri Jul 31 22:47:34 PDT 2009; root:xnu-1456.1.25~1/RELEASE_I386
System model name: MacBookPro7,1 (Mac-F222BEC8)
System uptime in nanoseconds: 109525048606
unloaded kexts:
(none)
loaded kexts:
com.apple.driver.AppleIntelYonahProfile 14
com.apple.driver.AppleIntelPenrynProfile 17
com.apple.DontSteal_Mac_OSX 7.0.0
com.apple.driver.AppleHDA 1.7.4a1
com.apple.driver.AppleGraphicsControl 2.8.16
com.apple.driver.AppleIntelNehalemProfile 11
com.apple.driver.AudioIPCDriver 1.1.0
com.apple.driver.AppleUpstreamUserClient 3.0.5
com.apple.driver.SMCMotionSensor 3.0.0d4
com.apple.driver.ACPISMCPlatformPlugin 3.4.0a20
com.apple.driver.AppleBacklight 170.0.2
com.apple.driver.AppleIRController 161
com.apple.driver.AppleIntelMeromProfile 19
com.apple.kext.AppleSMCLMU 1.4.5d1
com.apple.GeForce 6.0.0
com.apple.driver.DiskImages.SparseDiskImage 281
com.apple.driver.DiskImages.ReadWriteDiskImage 281
com.apple.driver.DiskImages.UDIFDiskImage 281
com.apple.driver.DiskImages.RAMBackingStore 281
com.apple.driver.DiskImages.HTTPBackingStore 281
com.apple.driver.DiskImages.FileBackingStore 281
com.apple.driver.AppleUSBTCButtons 1.8.0b4
com.apple.driver.AppleUSBTCKeyEventDriver 1.8.0b4
com.apple.driver.AppleUSBTCKeyboard 1.8.0b4
com.apple.driver.AppleUSBCardReader 2.5.0
com.apple.iokit.SCSITaskUserClient 2.5.0
com.apple.iokit.IOAHCIBlockStorage 1.5.0
com.apple.driver.AirPortBrcm43xx 410.91.20
com.apple.driver.AppleFWOHCI 4.3.4
com.apple.driver.AppleUSBHub 3.7.8
com.apple.driver.AppleAHCIPort 2.0.0
com.apple.driver.AppleUSBEHCI 3.7.5
com.apple.driver.AppleUSBOHCI 3.7.5
com.apple.BootCache 31
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.driver.AppleEFINVRAM 1.3.0
com.apple.driver.AppleRTC 1.3
com.apple.driver.AppleHPET 1.4
com.apple.driver.AppleSmartBatteryManager 160.0.0
com.apple.driver.AppleACPIButtons 1.3
com.apple.driver.AppleSMBIOS 1.4
com.apple.driver.AppleACPIEC 1.3
com.apple.driver.AppleAPIC 1.4
com.apple.driver.AppleIntelCPUPowerManagementClient 90.0.0
com.apple.security.sandbox 0
com.apple.security.quarantine 0
com.apple.nke.applicationfirewall 2.0.11
com.apple.driver.AppleIntelCPUPowerManagement 90.0.0
com.apple.driver.AppleHDAPlatformDriver 1.7.4a1 - last loaded 109517592692
com.apple.iokit.IOBluetoothSerialManager 2.2f18
com.apple.iokit.IOSerialFamily 10.0.2
com.apple.driver.AppleHDAHardwareConfigDriver 1.7.4a1
com.apple.driver.DspFuncLib 1.7.4a1
com.apple.iokit.IOAudioFamily 1.7.0fc16
com.apple.kext.OSvKernDSPLib 1.3
com.apple.driver.AppleHDAController 1.7.4a1
com.apple.iokit.IOHDAFamily 1.7.4a1
com.apple.driver.IOPlatformPluginFamily 3.4.0a20
com.apple.iokit.AppleProfileFamily 40
com.apple.iokit.IOFireWireIP 2.0.3
com.apple.driver.AppleSMC 3.0.1d2
com.apple.NVDAResman 6.0.0
com.apple.iokit.IONDRVSupport 2.0
com.apple.iokit.IOGraphicsFamily 2.0
com.apple.driver.DiskImages.KernelBacked 281
com.apple.driver.AppleUSBMultitouch 200.20
com.apple.iokit.IOUSBHIDDriver 3.7.5
com.apple.driver.BroadcomUSBBluetoothHCIController 2.2f18
com.apple.driver.AppleUSBBluetoothHCIController 2.2f18
com.apple.iokit.IOBluetoothFamily 2.2f18
com.apple.iokit.IOUSBMassStorageClass 2.5.0
com.apple.iokit.IOSCSIBlockCommandsDevice 2.5.0
com.apple.driver.AppleUSBMergeNub 3.7.5
com.apple.driver.AppleUSBComposite 3.7.5
com.apple.iokit.IOSCSIMultimediaCommandsDevice 2.5.0
com.apple.iokit.IOBDStorageFamily 1.6
com.apple.iokit.IODVDStorageFamily 1.6
com.apple.iokit.IOCDStorageFamily 1.6
com.apple.driver.XsanFilter 402.1
com.apple.iokit.IOAHCISerialATAPI 1.2.0
com.apple.iokit.IOSCSIArchitectureModelFamily 2.5.0
com.apple.iokit.IO80211Family 300.20
com.apple.iokit.IOFireWireFamily 4.1.7
com.apple.iokit.IOUSBUserClient 3.7.5
com.apple.iokit.IOAHCIFamily 2.0.0
com.apple.iokit.IOUSBFamily 3.7.8
com.apple.iokit.IONetworkingFamily 1.8
com.apple.driver.AppleFileSystemDriver 2.0
com.apple.driver.AppleEFIRuntime 1.3.0
com.apple.iokit.IOHIDFamily 1.6.0
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.TMSafetyNet 6
com.apple.kext.AppleMatch 1.0.0d1
com.apple.driver.DiskImages 281
com.apple.iokit.IOStorageFamily 1.6
com.apple.driver.AppleACPIPlatform 1.3
com.apple.iokit.IOPCIFamily 2.6
com.apple.iokit.IOACPIFamily 1.3.0

G5 Grey screen (Kernel Panic) when booting from CD

I know there are a lot of posts with people experiencing issues with the grey screen during boot. Most resolutions point to hardware but all state, including Apple's walk through, to boot from CD and run a validation on the hard drive.
My issue is completely different. I get the grey screen of death when booting from a CD/DVD only. I can boot into the OS just fine from the hard drive. But if I try to install another OS, or just boot from the CD/DVD, I get the grey screen.
What I've done to troubleshoot:
Reduced RAM to original sticks
Removed hard drive
Replaced DVD drive
Tried multiple versions of OS discs (10.2, 10.3, 10.4 and 10.4 server)
Reset the PRAM (Both via keyboard and Open Firmware)
Replaced the video card
Replaced the logic board
Replaced the Processor
Quite litterally the only thing original in this system is the power supply and the memory. However, I only get it when I'm booting from CD so the memory should not be the issue. I've even used a seperate power supply for the DVD drive to see if it was causing an issue.
Any suggestions? I'm looking at possibly replacing the power supply but I'm afraid it's going to give me the same issue.

Thats the thing, I've tried 10.2, 10.3, 10.4, and 10.4 server. (CD and DVD) All give me the grey screen. Well 10.2 and 10.3 give me a dark grey square in the middle where the apple should be but then the fans ramp up like it does when you get the grey screen of death.
I've also used two different drives.
It reads the disks fine with no issues. If I boot to the hard drive I can use the system like nothing is wrong. But if I want to boot from CD for any reason I cannot.
If I follow the logic it seems it is something to do with the CD/DVD drive. This is because it works fine when booted to hard drive. If it was the memory or PSU then I'd be getting the problem all of the time and not just when booting from CD/DVD.

Tiger DVD disk cause kernel panic when booting on a new G5

I was trying to boot a fairly new G5 system, less than 4 months old, using a retail copy of the 10.4 DVD installation disk. The computer could mount the disk and I can see its contents, but when I booted from it using the C key, I get a kernel panic.
I tried booting from the DVD on an older G5, and it worked without any problems. Assuming that it is not a DVD drive issue, do I need to get an update for the retail Tiger DVD disk to boot newer G5s?
Regards
m
Mac OS X (10.4)
G5 Mac OS X (10.4.5)

Welcome to Apple Discussions!
You can generally only use newer retail disks than the disks which came with the computer to boot and install operating systems, as well as those which came with the computer to boot and install operating systems. If you are missing the disks which came with your computer, call AppleCare to ask for a replacement.
This article explains that:
http://docs.info.apple.com/article.html?artnum=25517
As for installing operating system updates to your existing system, look here for updates:
http://www.apple.com/swupdates/
And if you are on dialup, some authorized service centers may let you bring in a CD to burn the updates. Check with the ones in your area.

PowerBook 17 crashes consistently, even when booted from Tiger DVD

We have a new PowerBook 17 that has started giving us problems in the last day or so. It will hang after running for a few minutes. This is a consistent problem - it doesn't go away for an hour, or a day - if the machine is running, it will hang. There is no kernel panic, no dialogue box, the trackpad, mouse, etc. simply stop responding (the clock freezes too, so I know the system is hanging up - not just input devices).
I've managed to run throught most of the normal trouble-shooting methods, I say "managed" because the machine froze when I was booting into single user mode. So I went to the Tiger DVD that shipped with the laptop. Upon getting to the language selection dialog box - it froze again (no mouse, keyboard activity, etc.). Eventually, the machine did boot from the startup DVD - and I ran disk utility. Of course it found no problems with permissions or the disk because this is apparently hardware related, no?
That being said, an archive and install will probably do us no good. But would Tech Tools (came with our AppleCare) manage to at least spot a Hardware issue? At this point, the only thing I haven't done is removed the third-party RAM we installed (which has been installed for nearly two weeks with no sign of conflict). That will be the next course of action and we'll run Tech Tools. Any ideas or suggestions regarding this issue would be greatly appreciated. We all know that being down one machine is not a good thing - thanks in advance for any assistance.
PowerBook G4 17" 1.67 Ghz Mac OS X (10.4.5) Might Mouse, 1.5 GB RAM, 100 GB HD
PowerMac G4 Mac OS X (10.4) 20" Cinema Display - 2G 20GB iPod - much, much more

David,
I always had a pristine system: no kernel panics, no system hangs. Then, one day I started to have kernel panics and hang ups and when I tried to install XCode it failed, then I couldn't install iWork '06. At first I thought it was a problem with the disk until I decided to run Apple's hardware test. After all, it was just a problem with one of the 512MBs memory DIMMs. Removed the offending DIMM and everything went back to normal.
So, I think you should try the hardware test. To do this just start up from the original installation disk while pressing the option key and then choose Apple Hardware Test from the available startup disks.

Kernel Panic when booting from Install Disk

My problem started when I was scanning my hard drive for problems with the Disk Utility.
It notified me that I do have some issues that could be resolved by restarting my computer with the Snow Leopard Installation Disk and running the DIsk Utility from there.
I tried to do that and it starts to boot up from the DVD but after about 30 seconds I get the Kernel Panic messege (You Need To Restart Your Computer...) in various languages and I have to restart again.
I also have the installation USB that comes with the MacBook Air and I get the same messege so I know it's not a problem with the installation disk itself.
Does anyone know what to do? I can't find a solution anywhere online.
Thank.
P.S
I have a Macbook Pro 2.4GHz Intel Core 2 Duo with 4GB of RAM.

Mr.V5 wrote:
I have disconnected all peripherals and I did a Safe Boot and I still get the Kernel Panic message.
I'm using the original Apple supplied RAM and I haven't added anything to the hardware since I bought it 8 months ago.
Eight months ago means you bought it used, yes?
The next step is to reseat the RAM, meaning remove it and put it back in.
If that doesn't work, then remove one module, try booting, move that module to the other slot, try booting, repeat with other module.
If neither RAM module works in either slot, then there are almost certainly other hardware issues (usually the logic board, which covers a plethora of possibilities; unfortunately, the fix for almost any LB issue is to replace the entire LB), as the odds of both RAM modules and/or both slots being faulty are extremely low (but possible).

Kernel Panic when boot MacBook Pro (related to ACPI driver)

Hi,
since the first day that I received my MacBook Pro I have a kernel panic sometimes (not always). When it occurs i have to hard reset the computer, and normally it comes another kernel panic (a second). Finally, in the third boot, it boots and all is ok, the system goes very well.
I only see one reference to this problem, a flickr photo at http://www.flickr.com/photos/christophermar/108747167/
The kernel panic is like this:
panic (cup 0 caller 0×0039AE87): Unable to find driver for this platform : “ACPI”.
Debugger called : <panic>
Backtrace, Format - Frame : Return Address (4 potential args on stack)
0xadc3e04 : 0×128b5e (0×3bb0bc 0xadc3e28 0×131bbc 0×0)
0xadc3e44 : 0×39ae87 (0×3de560 0×15c1780 0xadc3e74 0×15d2d40)
0xadc3e64 : 0×37ec4e (0×15d7b00 0×15b1c80 0×1 0×3afa77)
0xadc3ec4 : 0×3804d3 (0×15b1c80 0×15d7b00 0×15d2d40 0×15d8720)
0xadc3f44 : 0×37fd3d (0×15b1c80 0×15c7680 0×8 0xffffffff)
0xadc3f94 : 0×381486 (0×15b1c80 0×0 0×15c1500 0×0)
0xadc3fd4 : 0×197a21 (0×15c1500 0×0 0×15bf458 0×134aec) Backtrace terminated-invalid frame pointer 0×0
Kernel version :
Darwin Kernel Version 8.6.1: Tue Mar 7 16:55:45 PST 2006; root:xnu-792.9.22.obj~1/RELEASE_I386
You can see photos:
http://lotomas.net/wp-content/uploads/2006/04/CIMG1329.jpg
http://lotomas.net/wp-content/uploads/2006/04/CIMG1328.jpg
I have an actualized firmware and OS.
Any idea?
MacBook Pro Mac OS X (10.4.6)
MacBook Pro Mac OS X (10.4.6)

Well, finally I phoned Apple to change for new
MacBook Pro (less than 14 days).
I hope that new MacBook don't have this problem
because I fall in love with this "laptop"
Glad you are getting this taken care, and also glad I'm not the only one with this problem. I had kernel panics with my MBP, so I sent it back to amazon for a refund. It was my only real problem with the machine, though, which I loved otherwise. But kernel panics are a serious defect.
TiBook Mac OS X (10.3.9)

Kernal panic when booting from tiger disk

My friend just called me with a computer issue. She just got a used computer and it had a password setup. i told her how you can boot from the tiger install disk and reset it. She put the disk in and started holding down C before she turned it on. It sits there and thinks for a while and then she gets a kernal panic with the prohibitory sign before it gets anywhere (to the install screen). I have no idea what to tell her and she's 3 hours away so I can't really go over there easily.
Could the fact that she started holding down C before she turned it on make a difference?
Any help is appreciated.

The correct procedure for booting from the DVD is:
Start the computer and immediately after hearing the chime press and hold down the "C" key with one hand while inserting the DVD into the optical drive quickly with the other. Continue holding the "C" key down until the computer starts up from the DVD.
If the computer is already turned on, then insert the DVD into the optical drive. Restart the computer and immediately after the chime press and hold down the "C" key until the computer starts up from the DVD.
If the computer continues to panic despite the above procedure, then there's likely a major hardware problem.

Kernel Panic when booting external USB drive (WD Essential 250GB)

Greetings...I recently was tasked with setting up three bootable external volumes for a co-worker, so I purchased a Western Digital Essential 250 GB drive.
Everything worked just fine on my end, I was able to boot into each of the three external volumes continually and then shipped the drive to my co-worker, who when he tries to boot into any of the three drives gets a kernel panic.
We are using different models of MacBookPro (15 in. 2.16 Ghz Intel Core 2 Duo) for me and MacBookPro (15 in., 2.2 Ghz dual-processor Intel) for him. We THINK it might have to do with a firmware mismatch from the two machines:
Mine:
Boot ROM Version: MBP22.00A5.B07
SMC Version: 1.12f5
His:
Boot ROM Version: MBP31.0070.B07
SMC Version: 1.16f8
...but we've never had these types of problems before, even with mismatched hardware. The OS and kernel versions (10.4.11, Darwin 8.11.1) we're running are identical, according to ASP.
The only other weird thing is his panic log registers a different kernel version than what ASP reports, though that might be normal since hardware is not my thing:
Kernel version:
Darwin Kernel Version 8.9.1: Thu Feb 22 20:55:00 PST 2007; root:xnu-792.18.15~1/RELEASE_I386
In short, if anyone has any ideas how we can get these drives to boot or can confirm that it is impossible with the mismatched firmware so we can move forward with a plan B, I would greatly appreciate it.

Yes, sort of.
I used 10.4.8 disks to install, but used the Apple Software Update to upgrade to 10.4.11 on two of the volumes. I was still able to boot with my machine after that however.
As an update, my co-worker was able to "fix" one of the drives by upgrading with some 10.4.9 disks he had. He is now able to boot from that drive. That is not an option with the two others since they are already at 10.4.11.

Kernel panic when booting from CD

Hi all,
I've just tried to boot from a CD on my relatively new (4 months old) - i think this is the first time i have needed to boot off a CD.
My Panther CD boots as far as the apple logo, then it looks like a few pixels in the centre of the screen get jumbled around - and the computer does not load any further.
If I boot off a DiskWarrior CD (latest version 3.03) I get a black Darwin screen with lots of text and a Kernel Panic "we are hanging here" error, as well as a small box saying that I need to hold down the power button.
My hard disk boots OK - but I am wanting to boot from CD to repair a couple of disk errors that the drive has.
Any ideas? Faulty CD drive?
Kim

If you system is only 4 months old you very likely need a version of the OS on CD that is newer than what you are using. I had a problem with my 1.5GHz PB 17" a while back (just before Tiger came out) and I tried to boot it from a Panther 10.3.0 retail CD and it started okay then bombed - and I thought it was the somethign serious - turns out that I should have used the CD that came with it originally which had verison 10.3.3 or so - then everything was okay.

Kernel Panic when booting from OS X install CD

Hello,
I have a PowerMac G4 Mirrored Door that used to run 10.4.8 and was acting wonky. I repaired permissions and did the hardware test to no avail so I decided to clear the drive and reinstall the OS.
I reinstalled 10.2.1 with the original CD's and that went smoothly. I then attempted to update to 10.4.8 with the OS 10.4 install CD's that we had purchased. And when the computer tries to boot from the CD I get a Kernel Panic once the apple appears on the grey screen but before the status bar starts turning.
I reset the PRAM and updated to 10.2.8 but still got the panic when I tried again.
Here is the begining of the panic code:
panic cpu 0 caller 0x002E54BC: Unable to find driver for this platform: "PoerMac3,6"
The CD's I used say "For Mac Computers".
Any ideas would be much appreciated.
Sincerely,
Nick

Unfortunatlly I was not here when the computer was upgraded last (I freelance at a studio with many computers that need constant attention). I was told that these were the CD's that were purchased for the upgrade and I've looked in vain for others.
They are 2 gray Apple CD's. The first install CD says "For Mac Computers" above Mac OS X install Disc 1. They each came in a sleeve with a sticker that says "Common Media Multillingaul"
These are the wrong CD's, aren't they? The correct ones have been lost, haven't they?
I was really hoping that wasn't the case.

Kernel Panics when booted to external FW using 10.4.8

Using 10.4.7 things worked fine whether I booted on internal drive or external LaCie D2 FW
I upgraded to 10.4.8 on the PB G4 15", a PB G4 12" and an external LaCie 2D 3-port firewire
The PB 15" and the PB 12" work fine, read/write, etc and backed up the LaCie drive fine
Boot from either PB to the LaCie drive and I get a kernel panic (below) within seconds
- Problem exists with both PBs 12" & 15" (but I ran TechTool to make sure things (RAM, etc) are fine
- Reset PRAM and PMU
- Booted in Safe mode
- Ran Permissions update
- Reinstalled 10.4.8, then 10.4.8 combo
- Used disk Utility to repair disk, minor problems
- Eliminated all start up apps
Last night it would run for five minutes before panic, today, just boot to FW and panic will happen in 15 secs - no apps running
Sorry about the long logs, will edit them out after resolution
Flack
Panic Log:
Wed Oct 11 09:11:16 2006
panic(cpu 0 caller 0x000E3DDC): vnode_writedone: numoutput < 0
Latest stack backtrace for cpu 0:
Backtrace:
0x00095138 0x00095650 0x00026898 0x000E3DDC 0x000D8A24 0x004FE230 0x004F0FF4 0x008C7C80
0x008CAA38 0x008CAB38 0x00598FFC 0x0059922C 0x0073627C 0x007366B8 0x00721C6C 0x007216EC
0x00552A44 0x00534040 0x00533940 0x007ABAD4 0x0079B450 0x002D0B94 0x002CFA5C 0x000A9314
Kernel loadable modules in backtrace (with dependencies):
com.apple.iokit.IOSCSIReducedBlockCommandsDevice(1.4.9)@0x8c6000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOFireWireSerialBusProtocolTransport(1.4.4)@0x734000
dependency: com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
com.apple.driver.AppleFWOHCI(2.5.3)@0x795000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x45f000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
Proceeding back via exception chain:
Exception state (sv=0x2D054780)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
Wed Oct 11 09:29:41 2006
panic(cpu 0 caller 0x000E3DDC): vnode_writedone: numoutput < 0
Latest stack backtrace for cpu 0:
Backtrace:
0x00095138 0x00095650 0x00026898 0x000E3DDC 0x000D8A24 0x004FE230 0x004F0FF4 0x008C7C80
0x008CAA38 0x008CAB38 0x00598FFC 0x0059922C 0x0073627C 0x007366B8 0x00721C6C 0x007216EC
0x00552A44 0x00534040 0x00533940 0x007ABAD4 0x0079B450 0x002D0B94 0x002CFA5C 0x000A9314
Kernel loadable modules in backtrace (with dependencies):
com.apple.iokit.IOSCSIReducedBlockCommandsDevice(1.4.9)@0x8c6000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOFireWireSerialBusProtocolTransport(1.4.4)@0x734000
dependency: com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
com.apple.driver.AppleFWOHCI(2.5.3)@0x795000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x45f000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
Proceeding back via exception chain:
Exception state (sv=0x2CFB7A00)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
Wed Oct 11 12:40:38 2006
panic(cpu 0 caller 0x000E3DDC): vnode_writedone: numoutput < 0
Latest stack backtrace for cpu 0:
Backtrace:
0x00095138 0x00095650 0x00026898 0x000E3DDC 0x000D8A24 0x2E05D230 0x2E04FFF4 0x2E96CC80
0x2E96FA38 0x2E96FB38 0x2DFC0FFC 0x2DFC122C 0x2E3E727C 0x2E3E76B8 0x2E358C6C 0x2E3586EC
0x2DE15A44 0x2DDF7040 0x2DDF6940 0x2DE65AD4 0x2DE55450 0x002D0B94 0x002CFA5C 0x000A9314
Kernel loadable modules in backtrace (with dependencies):
com.apple.iokit.IOSCSIReducedBlockCommandsDevice(1.4.9)@0x2e96b000
dependency: com.apple.iokit.IOStorageFamily(1.5)@0x2e04a000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x2dfb9000
com.apple.iokit.IOFireWireSerialBusProtocolTransport(1.4.4)@0x2e3e5000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x2dfb9000
dependency: com.apple.iokit.IOFireWireSBP2(1.7.5)@0x2e355000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x2dded000
com.apple.iokit.IOFireWireSBP2(1.7.5)@0x2e355000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x2dded000
com.apple.iokit.IOStorageFamily(1.5)@0x2e04a000
com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x2dfb9000
com.apple.driver.AppleFWOHCI(2.5.3)@0x2de4f000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x28075000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x2dded000
com.apple.iokit.IOFireWireFamily(2.2.5)@0x2dded000
Proceeding back via exception chain:
Exception state (sv=0x2DA57780)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
Wed Oct 11 12:48:52 2006
panic(cpu 0 caller 0x000E3DDC): vnode_writedone: numoutput < 0
Latest stack backtrace for cpu 0:
Backtrace:
0x00095138 0x00095650 0x00026898 0x000E3DDC 0x000D8A24 0x004FE230 0x004F0FF4 0x008C7C80
0x008CAA38 0x008CAB38 0x00598FFC 0x0059922C 0x0073627C 0x007366B8 0x00721C6C 0x007216EC
0x00552A44 0x00534040 0x00533940 0x007ABAD4 0x0079B450 0x002D0B94 0x002CFA5C 0x000A9314
Kernel loadable modules in backtrace (with dependencies):
com.apple.iokit.IOSCSIReducedBlockCommandsDevice(1.4.9)@0x8c6000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOFireWireSerialBusProtocolTransport(1.4.4)@0x734000
dependency: com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
com.apple.driver.AppleFWOHCI(2.5.3)@0x795000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x45f000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
Proceeding back via exception chain:
Exception state (sv=0x2CFB7A00)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
Wed Oct 11 13:15:31 2006
panic(cpu 0 caller 0x000E3DDC): vnode_writedone: numoutput < 0
Latest stack backtrace for cpu 0:
Backtrace:
0x00095138 0x00095650 0x00026898 0x000E3DDC 0x000D8A24 0x004FE230 0x004F0FF4 0x008C7C80
0x008CAA38 0x008CAB38 0x00598FFC 0x0059922C 0x0073627C 0x007366B8 0x00721C6C 0x007216EC
0x00552A44 0x00534040 0x00533940 0x007ABAD4 0x0079B450 0x002D0B94 0x002CFA5C 0x000A9314
Kernel loadable modules in backtrace (with dependencies):
com.apple.iokit.IOSCSIReducedBlockCommandsDevice(1.4.9)@0x8c6000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOFireWireSerialBusProtocolTransport(1.4.4)@0x734000
dependency: com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
com.apple.driver.AppleFWOHCI(2.5.3)@0x795000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x45f000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
Proceeding back via exception chain:
Exception state (sv=0x2D054780)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
Wed Oct 11 13:19:23 2006
panic(cpu 0 caller 0x000E3DDC): vnode_writedone: numoutput < 0
Latest stack backtrace for cpu 0:
Backtrace:
0x00095138 0x00095650 0x00026898 0x000E3DDC 0x000D8A24 0x004FE230 0x004F0FF4 0x008C7C80
0x008CAA38 0x008CAB38 0x00598FFC 0x0059922C 0x0073627C 0x007366B8 0x00721C6C 0x007216EC
0x00552A44 0x00534040 0x00533940 0x007ABAD4 0x0079B450 0x002D0B94 0x002CFA5C 0x000A9314
Kernel loadable modules in backtrace (with dependencies):
com.apple.iokit.IOSCSIReducedBlockCommandsDevice(1.4.9)@0x8c6000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOFireWireSerialBusProtocolTransport(1.4.4)@0x734000
dependency: com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
com.apple.driver.AppleFWOHCI(2.5.3)@0x795000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x45f000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
Proceeding back via exception chain:
Exception state (sv=0x2CFB7A00)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
PB G4 15", PB G4 12" Mac OS X (10.4.8) LaCie 180GB FW

Using 10.4.7 things worked fine whether I booted on internal drive or external LaCie D2 FW
I upgraded to 10.4.8 on the PB G4 15", a PB G4 12" and an external LaCie 2D 3-port firewire
The PB 15" and the PB 12" work fine, read/write, etc and backed up the LaCie drive fine
Boot from either PB to the LaCie drive and I get a kernel panic (below) within seconds
- Problem exists with both PBs 12" & 15" (but I ran TechTool to make sure things (RAM, etc) are fine
- Reset PRAM and PMU
- Booted in Safe mode
- Ran Permissions update
- Reinstalled 10.4.8, then 10.4.8 combo
- Used disk Utility to repair disk, minor problems
- Eliminated all start up apps
Last night it would run for five minutes before panic, today, just boot to FW and panic will happen in 15 secs - no apps running
Sorry about the long logs, will edit them out after resolution
Flack
Panic Log:
Wed Oct 11 09:11:16 2006
panic(cpu 0 caller 0x000E3DDC): vnode_writedone: numoutput < 0
Latest stack backtrace for cpu 0:
Backtrace:
0x00095138 0x00095650 0x00026898 0x000E3DDC 0x000D8A24 0x004FE230 0x004F0FF4 0x008C7C80
0x008CAA38 0x008CAB38 0x00598FFC 0x0059922C 0x0073627C 0x007366B8 0x00721C6C 0x007216EC
0x00552A44 0x00534040 0x00533940 0x007ABAD4 0x0079B450 0x002D0B94 0x002CFA5C 0x000A9314
Kernel loadable modules in backtrace (with dependencies):
com.apple.iokit.IOSCSIReducedBlockCommandsDevice(1.4.9)@0x8c6000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOFireWireSerialBusProtocolTransport(1.4.4)@0x734000
dependency: com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
com.apple.driver.AppleFWOHCI(2.5.3)@0x795000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x45f000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
Proceeding back via exception chain:
Exception state (sv=0x2D054780)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
Wed Oct 11 09:29:41 2006
panic(cpu 0 caller 0x000E3DDC): vnode_writedone: numoutput < 0
Latest stack backtrace for cpu 0:
Backtrace:
0x00095138 0x00095650 0x00026898 0x000E3DDC 0x000D8A24 0x004FE230 0x004F0FF4 0x008C7C80
0x008CAA38 0x008CAB38 0x00598FFC 0x0059922C 0x0073627C 0x007366B8 0x00721C6C 0x007216EC
0x00552A44 0x00534040 0x00533940 0x007ABAD4 0x0079B450 0x002D0B94 0x002CFA5C 0x000A9314
Kernel loadable modules in backtrace (with dependencies):
com.apple.iokit.IOSCSIReducedBlockCommandsDevice(1.4.9)@0x8c6000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOFireWireSerialBusProtocolTransport(1.4.4)@0x734000
dependency: com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
com.apple.driver.AppleFWOHCI(2.5.3)@0x795000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x45f000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
Proceeding back via exception chain:
Exception state (sv=0x2CFB7A00)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
Wed Oct 11 12:40:38 2006
panic(cpu 0 caller 0x000E3DDC): vnode_writedone: numoutput < 0
Latest stack backtrace for cpu 0:
Backtrace:
0x00095138 0x00095650 0x00026898 0x000E3DDC 0x000D8A24 0x2E05D230 0x2E04FFF4 0x2E96CC80
0x2E96FA38 0x2E96FB38 0x2DFC0FFC 0x2DFC122C 0x2E3E727C 0x2E3E76B8 0x2E358C6C 0x2E3586EC
0x2DE15A44 0x2DDF7040 0x2DDF6940 0x2DE65AD4 0x2DE55450 0x002D0B94 0x002CFA5C 0x000A9314
Kernel loadable modules in backtrace (with dependencies):
com.apple.iokit.IOSCSIReducedBlockCommandsDevice(1.4.9)@0x2e96b000
dependency: com.apple.iokit.IOStorageFamily(1.5)@0x2e04a000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x2dfb9000
com.apple.iokit.IOFireWireSerialBusProtocolTransport(1.4.4)@0x2e3e5000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x2dfb9000
dependency: com.apple.iokit.IOFireWireSBP2(1.7.5)@0x2e355000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x2dded000
com.apple.iokit.IOFireWireSBP2(1.7.5)@0x2e355000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x2dded000
com.apple.iokit.IOStorageFamily(1.5)@0x2e04a000
com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x2dfb9000
com.apple.driver.AppleFWOHCI(2.5.3)@0x2de4f000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x28075000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x2dded000
com.apple.iokit.IOFireWireFamily(2.2.5)@0x2dded000
Proceeding back via exception chain:
Exception state (sv=0x2DA57780)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
Wed Oct 11 12:48:52 2006
panic(cpu 0 caller 0x000E3DDC): vnode_writedone: numoutput < 0
Latest stack backtrace for cpu 0:
Backtrace:
0x00095138 0x00095650 0x00026898 0x000E3DDC 0x000D8A24 0x004FE230 0x004F0FF4 0x008C7C80
0x008CAA38 0x008CAB38 0x00598FFC 0x0059922C 0x0073627C 0x007366B8 0x00721C6C 0x007216EC
0x00552A44 0x00534040 0x00533940 0x007ABAD4 0x0079B450 0x002D0B94 0x002CFA5C 0x000A9314
Kernel loadable modules in backtrace (with dependencies):
com.apple.iokit.IOSCSIReducedBlockCommandsDevice(1.4.9)@0x8c6000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOFireWireSerialBusProtocolTransport(1.4.4)@0x734000
dependency: com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
com.apple.driver.AppleFWOHCI(2.5.3)@0x795000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x45f000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
Proceeding back via exception chain:
Exception state (sv=0x2CFB7A00)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
Wed Oct 11 13:15:31 2006
panic(cpu 0 caller 0x000E3DDC): vnode_writedone: numoutput < 0
Latest stack backtrace for cpu 0:
Backtrace:
0x00095138 0x00095650 0x00026898 0x000E3DDC 0x000D8A24 0x004FE230 0x004F0FF4 0x008C7C80
0x008CAA38 0x008CAB38 0x00598FFC 0x0059922C 0x0073627C 0x007366B8 0x00721C6C 0x007216EC
0x00552A44 0x00534040 0x00533940 0x007ABAD4 0x0079B450 0x002D0B94 0x002CFA5C 0x000A9314
Kernel loadable modules in backtrace (with dependencies):
com.apple.iokit.IOSCSIReducedBlockCommandsDevice(1.4.9)@0x8c6000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOFireWireSerialBusProtocolTransport(1.4.4)@0x734000
dependency: com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
com.apple.driver.AppleFWOHCI(2.5.3)@0x795000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x45f000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
Proceeding back via exception chain:
Exception state (sv=0x2D054780)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
Wed Oct 11 13:19:23 2006
panic(cpu 0 caller 0x000E3DDC): vnode_writedone: numoutput < 0
Latest stack backtrace for cpu 0:
Backtrace:
0x00095138 0x00095650 0x00026898 0x000E3DDC 0x000D8A24 0x004FE230 0x004F0FF4 0x008C7C80
0x008CAA38 0x008CAB38 0x00598FFC 0x0059922C 0x0073627C 0x007366B8 0x00721C6C 0x007216EC
0x00552A44 0x00534040 0x00533940 0x007ABAD4 0x0079B450 0x002D0B94 0x002CFA5C 0x000A9314
Kernel loadable modules in backtrace (with dependencies):
com.apple.iokit.IOSCSIReducedBlockCommandsDevice(1.4.9)@0x8c6000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOFireWireSerialBusProtocolTransport(1.4.4)@0x734000
dependency: com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireSBP2(1.7.5)@0x71e000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOStorageFamily(1.5)@0x4eb000
com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x591000
com.apple.driver.AppleFWOHCI(2.5.3)@0x795000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x45f000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
com.apple.iokit.IOFireWireFamily(2.2.5)@0x52a000
Proceeding back via exception chain:
Exception state (sv=0x2CFB7A00)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
PB G4 15", PB G4 12" Mac OS X (10.4.8) LaCie 180GB FW

Kernel panic when booting btrfs raid1 without sda

Hi,
I'm using a default kernel 3.6.3 and have a btrfs raid1 (data and metadata) over two hard drives (sda3 and sdb). My system is a subvolume, which works fine. If I remove the first hard drive (which contains grub2), however, and boot using a live cd, I get a kernel panic (image at http://s12.postimage.org/8y0pgvs99/arch … panic.png)
whenever I try to mount the remaining raid1 as degraded
mount -o degraded /dev/sda /mnt
(/sda then is the one and only hard disk).
I do this all for testing reasons: I want to simulate a hard drive failure. But right now it just looks like I could not access that data in case of a real failure ;-(
There are some kernel patches
https://patchwork.kernel.org/patch/1267581/
http://www.spinics.net/lists/linux-btrfs/msg17007.html
concerning this issue, which seem to have entered the default kernel, and yet the error persists. (They are contained in the Arch kernel, aren't they?)
Any suggestions?

In case anyone has the same problems as I did: I found a workaround.
I installed grub on both devices. Since my /boot and / are only subvolumes in the btrfs `device', they are on both physical disks. If the first device fails, I simply boot from the grub of the second disk into the system stored on the second disk (with mount option `degraded') -- and since I mount the btrfs-disk via UUID, I don't have to change /etc/fstab or anything.

Kernel Panic when booting to Tiger DVD

Similar Messages

Maybe you are looking for