Kingston, Crucial, Twinmos memory has problem with K7N2-DELTA??

I need 2*256MB memory for my AMD 2500+XP.
Kingston, Crucial, Twinmos memory seem to have problem with K7N2-DELTA-ILSR
Is Samsung good?
Please do me a favor to choose one brand that fit my mobo in this link:
http://www.canadacomputers.com/memory.html
I tried KingMax(SuperRam Series, since they don't have the ram with the model listed in the test report) and Corsair(CMX256A-3200C2) ,both no good for 2*256MB DUAL channel
Thank you very much

I think OCZ and Samsung, is mostly work memory,r ight?
thx
I think I will try OCZ

Similar Messages

Serius problem with k7n2 delta 2

I have problems with my k7n2 delta2 does not recognize a AtlonXP 3000+ was working in this plate, doing tests of overclock,when to restart do not work the processor in this plate but,the motherboard (k7n2 delta 2) works with other processors, and processor 3000+ works with other motherboards, but Athlon 3000+ with k7n2 delta 2 does not work together, I tested of everything recover the bios, to update the bios and nothing, dont change to default, I hope that can help me beforehand thankful.
tengo problemas con mi k7n2 delta2 no reconoce un AtlonXP 3000+ que ya estaba trabajando en esta placa madre, haciendo pruebas de overclock, y despues de reiniciarla ya no quiso reconocer el procesador athlon xp 3000+, la placa madre (k7n2 delta 2) trabaja con otros procesadores, y el procesador 3000+ trabaja con otras placas madres, pero el Athlon 3000+ con k7n2 delta 2 no trabajan juntos, ya he probado de todo restaurar el bios, actualizar el bios y nada, parece que no efectua los cambios a default, no se que hacer, espero que me puedan ayudar agradecido de antemano.
cuando tiene otro cpu enciende correctamente pero cuando le pongo el xp 3000+ no enciende el monitor ni marca ningun error solo no inicias, pero si enciende.

Why do you say Bios doesn't go to default options if with other CPUs Mobo turns on ? You must have in mind that each time you replace the CPU you must Clear CMOS to return to default options, and also you should clean HSF base and CPU die from old thermal grease. At least you know both CPU and Mobo works.
Por qué dices que la Bios no vuelve a las opciones por defecto si la tarjeta madre funciona con otros procesadores ? Debes tener en cuenta que cada vez que cambias de CPU deberías borrar las opciones que entraste en la Bios como también limpiar la base del disipador de temperatura de la CPU y la CPU misma y usar nueva pasta térmica. Al menos sabes que tanto la CPU como la tarjeta madre trabajan.

[nForce] Problems with K7N2 Delta 2 Platinum and SATA

Hi All
I have a MSI K7N2 Delta 2 Platinum with an AMD 3200+ Barton.
I have 2 x 512mb Crucial PC3200 DDR400 RAM.
I have a Samsung 80gb SATA hard drive.
I am trying to install Windows XP Pro onto a blank SATA drive. The trouble is that I get into the Win XP Pro setup and it just doesn't recognise the drive. I have tried installing the drivers on the Flopy, but the drive just isnt recognised for me to install Win XP to the SATA drive to use as a boot drive.
I've read the advice thread, but couldn't find my problem.
Any help would be much appreciated!
Thanks

Thank for that. I haven't done that but I have got XP to recognise the drive to install to it.
XP went as far as going to the lovely bright XP installation screen and has installed hardware. When it got to installing the network it just froze up and stopped working.
Now I think the problem may be that I set the one SATA drive up to be RAID (striped) in the RAID config. I will disable this tonight and have another look. The thing that I would like to know is what setting in the BIOS of this mobo means that the SATA drive can be used as IDE? I don't have two SATA drives to use in RAID, so I figured that I have to get the one SATA to act as an IDE drive. I have SATA spreading disabled, but am unsure as to which of the other settings to change. Soz to keep asking!
EDIT: I sorted the RAID config thing. Fomatted the drive and re-installed XP. Once again, it just stops once it gets to the windowsesque creen. It stops at various points during the installation, sometimes at the "installing networks" bit, sometimes at the "completing installation" (after coying data). I just don't know what to do realy. Might RMA the board and go back to my trusted old Aopen AK77-600GN :-(
Anyone any ideas?

Problem with K7N2 Delta-ILSR, please help

First off, these are the specs for the computer to which I shall be referring in this post:
K7N2 Delta-ILSR
AMD 2700+
1x512MB PC3200 Memory Corsair CM64SD512
Seagate Barracuda 80GB 7200RPM SATA ST380013AS
ATI 9600 Pro
400 Watt power supply
Cendyne 52x cd burner
Here's what happened. I installed everything with only minor difficulties, mostly due to getting the hard drive to work. They were worked through with little problem due, in large part, to this forum. I installed Windows XP, and we ran a number of things with no problem after the OS installation. The drivers for the video card loaded well. 3DMark2003 ran beautifully. After I got that working, I went to put my friend's old hard drive in as a slave, so he could get the files off of it. This seemed to work well enough. Then we went to load the drivers for the motherboard. When it got to the audio driver, we got the old "blue screen". Then the computer reset and tried booting 98 from the old hard drive. We shut down and disconnected the old hard drive. Then we restarted to find that after the second screen XP would not begin to boot. After some playing around we decided it best to reinstall, because with no combination could we get the OS to boot up. So we reinstalled, with a full format. This time, the first thing I went for was the motherboard drivers. It stopped at the audio driver, again, and gave us the old "blue screen", again. This time, instead of stopping the boot after the second screen, it came up with this message
Windows could not start because the following file is missing or corrupt:
\system32\hal.dll.
Please re-install a copy of the above file.
Any suggestions would be greatly appreciated before we decide what to do next. Please let me know if any more information is required. None of the bios settings have been altered, save to boot from the CD.
Thank you,
M.Cordier

i would test ram
http://www.memtest86.com
and go to drive makers site and get their testing utility
other possibility is a crap psu like them qtecs

Problem with K7N2 delta

Im having a problem with the K7N2 Delta. It was working just fine and i went into my Bios and saw that my FSB was only running at 133mgz. So i turnt it up to 200mgz. Now the darn think hangs and wont turn on. I tried to clear the Cmos and set the bus jumper to safe mode but then the computer just beeps. I dont understand what i did wrong. Any suggestions?
CPU- Xp2400+
Mobo- K7n2 Delta
Ram- 256 Atlas Percision 256 Kingston
Veido- Geforce FX 5700 Ultra
Hd- 4 gig western Digital / 20 gig western digital 7200rpm
power-300watt

well you o/c it about 50 percent and it will not have it
put j10 jumkper in safe mode
boot and put it back to 133
then shut down and put it in user mode

Problems with K7N2 Delta-L

Hi, I am new here, so hello :D
Well, I've just bought a MSI K7N2 Delta-L, beautifull board, with 2 x 256MB DDR400...
My actual PC, so:
MSI K7N2 Delta-L
Athlon XP 1700+ 1.5v DLT3C JIUHB
Thermaltake Volcano 7+
2 x 256MB PC3200 VM
Well, I updated bios to the last one (5.4) and all is running ok... but I have some problems.
1) I have problems when I try to overclock. One ot them, is that when I change a multiplier, o up the fsb... I must change jumpers, etc. etc. coz pc doesnt boot ... but later when I played with jumpers, it boot at speed that I wanted, like 10x200, etc. I dont know how to explain this problem! :(
2) Well, another problem is with "By H/W" option in vCore and Multiplier. When I select this option, the vCore sometimes go to 1.8v ... and when I select 1.8v, if it wants, its go to 1.6v in win... I dont know what to do, bios do what he wants.
3) Well, the last and I think most important problem, is when I try to change CAS Latency. I have 2.5-3-3-7 DDR400 memory. When I try to change CAS Latency to 2, in bios, its all right, it's boots, and figures CAS 2. But when I enter windows, ALL programs, says that CAS Latency is 2.5 !!! I tried lowering FSB to 133, and trying again CAS 2, but nothing, still CAS2.5 in win. I runned benchmarks, but no perfomance gaining with BIOS CAS2. What happens!!?? Another thing, was that if I put in BIOS, AUTO, when I chane FSB to 233, CAS Latency goes to 3, when I put FSB to 200, CAS Latency goes to 2.5, when I put FSB to 166, CAS Latency remains in 2.5, when I put FSB to 133, IT STILL BEEING in 2.5 .. !! It doesnt change... the same in FSB 100.
HELP!!! and thanks a lot :(
PD: Same problems with all bios.

Quote
Originally posted by Dancer
Quote
Originally posted by lmichani
Another problem, expanding problem "3)"
In bios, I go to multiplier option, I select 9.5.
In FSB, 200.
Then, in vCore, I select by H/W...
Save... ---> ... WOHOO !! 2200 MHz!
WHY !!?? (200 x 11 says in win) ... SSHHIITT!
- Another problem... when I select by H/W in vCore... it goes to 1.8v!!!!
IS GOING ON WITH MY BOARD? Is the crappy bios?!
Bump all you want, with this kind of language I don't think you're going to get an answer. :O Read the rules of the forum!
I didnt know that "SSHHIITT" and ":censored:" were "bad words"; btw I deleted them.
next time say me that by PM.

Odd USB Problem With K7N2 Delta-L

Hey all. I have a bit of a weird problem here I'm wondering if people can give some insight on. I have a K7N2 Delta-L mainboard that I've been using for two years now without the slightest problem. However, recently I've started experiencing some odd USB related problems which culminated in a big moment of panic for me yesterday. I'll start with what happened yesterday.
My system drive is 2x40GB PIDE drives running on an add-in Promise FastTrak133 controller. Yesterday, I was given 2x160GB drives from a client that I decided to upgrade my RAID with. I installed the drives and fired up my system, but had to reboot several times as the drives weren't jumpered right and not detecting on the Promise board. After I finally got the drives working, I noticed my USB had completely died. My USB keyboard and mouse didn't work and my TrueImage rescue disk (which I was going to use to restore my backup to the new RAID with) couldn't see the USB hard disk which contained the backup. I panicked about this for a while, but eventually managed to restore the keyboard and USB drive by unplugging the system, pulling the battery, waiting 15 minutes, putting the battery back and starting up. My mouse still didn't work, but once I got into Windows, it started to work after unplugging it and replugging it three times. All these devices work immediately when plugged into my laptop so I know they are OK.
Also, for the last few months leading up to yesterday, I've been having a problem with some USB devices not detecting properly when I startup. For example, the mouse will not respond until I either replug it (sometimes more than once) or on some occasions, just mash the buttons a few times at which point it kicks in. I also find that sometimes if I switch the keyset on my Zboard (which resets its USB connection), sometimes it won't get recognized as attached to the system unless I disconnect it or reboot. Both of these devices work perfectly in other systems I've tried them on and once I get them running in Windows, they don't kick out again unless the system is shut down (and they only fail to work on some boots, not all.) Every other aspect of the system works flawlessly.
I was wondering, has anyone else seen this before and is it something I can correct? Is this a sign that possibly the board is starting to die and I should look at upgrading? If I install an add-in USB card and disable the on-board USB, will I still be able to boot from USB devices? I cannot really afford a major upgrade right now, but I also can't afford to lose this system so I'll make the investment if this is a potential sign the board is failing. Thanks for reading and any help you can provide.
P.S. Here is a list of USB devices connected to my system, all of which I've tried disconnecting without fixing the problem:
Razer Copperhead Gaming Mouse (Latest Drivers & Firmware)
Ideazon Zboard (Latest Drivers)
Artec e48U+ Scanner (Latest Drivers, Powered By USB)
iMex USB 2.0 External HDD Enclosure
HP Photosmart 7600 Photo Printer (Runs Through Zboard USB Hub)

the PSU looks fine and should be capable of providing more than enough power - unless it is faulty for some reason. is it clogged up with dust? do you have another one you can test with?
does your case have its own USB port(s), if so disconnect from motherboard and see if that makes any difference
also, try going to Device Manager, uninstalling all the Host Controllers listed under Universal Serial Bus controllers, and then rebooting to reinstall the drivers
i presume you have already referred to this sticky topic: If you are having problems with USB ports, read this topic.

Problems with K7N2 DELTA 2 LSR and reader LG 52X max

My computer has one mainboard MSI K7N2 DELTA2 LSR. updates the bios to version 11.4 but asi when even inserted a CD the coputador sticks my D-ROM is a LG 52X MAX. that can help me.
I am Chilean for that reason my English is not very good.

what it happens to me is that it is congealed, but when extracting the CD defrosts by ningun reason sticks. when it updates the bios to the B4. I work in the beginning well but despues I reiterate the problem that could now be I put my computer in my signature
the reason to update the bios ones was the problem with the cd player
lo que me sucede es que se congela, pero al extraer el cd se descongela por ningun motivo se pega.
cuando actualice la bios a la B4. al principio funciono bien pero despues se reitero el problema. que podrá ser. ahora puse mi computador en mi firma.
la razon para actualizar la bios era el problema con el lector de cd

Problems with K7N2 Delta @ FSB200Mhz

Hi,
SORRY FOR MY POOR ENGLISCH
I've got a problem with my K7N2 Delta -L Board.
I use a Athlon XP Palo 1700+. Standart for this proz is FSB 133 and multi 11.
Now i tried to use FSB 200 an multi 7,5. =>1500Mhz.
I works fine an never crashs.
BUT if i turn off the pc for more than 15mins it doesn't reboot anymore. Only a safereboot@100mhz is possible.
The setting have to be in the BIOS advanced chipset AUTO an FSB 200 than it boots and restarts without problems until i turn it off.
The setting MANUAL and FSB 200 doesn't work even if i don't change any other setting. It never boots
RAM : CPU is 1:1. RAM is 400Mhz
What's wrong?

Yes, the Proz is unlocked. It works fine. The "strange" thing is, that after a shutdown and power-off of more then 15min it hangs while rebooting.
You have to choose auto performance and FSB 200 otherwise it does't works with FSB higher than 150
Why raise the v-core? It works fiin without probs and stable only boot-probs after power-off . Reboots works fine.
The same proble occurs while using FSB 166.
What has MSI done?
Auto FSB200 works
Manual FSB 200 not
and the aren't able to reply to e-mails...
Sorry next time spend some more € for an working a*us MB

Problems with K7N2 Delta mobo

Hey I'm new here because of a problem I've had with the K7N2 Delta motherboard. I've done some research and I've noticed the problem appear to other users of this mobo as well. Before I bought this mobo I had a soundblaster live! value sound card and when I intalled this mobo I thought I wouldn't need my soundblaster soundcard so I stored it away. Well after a few months my pantience ran thin on this mobo's sound problems. For one, it keeps making this static like sound sometimes, so I tried to install my soundblaster sound card on the new mobo, I downloaded the lastest driver for it and changed my default sound driver to the soundblaster live! that I have but it made no sound at all. After removing the nvidia nForce 2 sound driver I had on my mobo to see if it would help I still had no luck in making my soundcard work. Is it possible that the soundcard is conflicting with the mobo's internal audial capability?

Hi,
Vampir, and welcome to the forum
Try putting your your soundcard in PCI slot 3.
Is it the -L version or the ILSR version motherboard you are using!
Read this the thread at the link below then repost!:
Nobby's Moan Guide
Btw, how many IRQ's do you have 16 or 23?
To find your list of IRQ's:
Go to Start>Run> Then Type: "msinfo32" (without quotes). The "System Information" window should now be open. Click on + "Hardware Resources" in left pane - then on IRQ's in the list that appears below it. You should now see a list of all IRQ's in the left panel! Which can be cut and pasted if you wish!
They can also be found in Device Manager!
Axel

Problem with K7N2 Delta ILSR?

Hi
Not sure if there is a problem or not but I have:
K7N2 Delta ILSR
Athlon XP 2.8GHz
512Meg Ram
Win XP SR2
When I check in System Properites, on the General Tab, at the bottom though it reports I have a AMD Athlon(tm) XP 2800+, correctly, however underneath it says "2.08 GHz, 512 Mb RAM".
What happened to the other 0.7 Ghz !
In the BIOS, the FSB is set to 166 Mhz as recommeded. If set to 100 MHz, in the BIOS the clock speed appears as 1250Mhz! Surely that's not right.
I know it wont run at the full 2.8 GHz but I thought it should only be a little less than that? Is this normal?
Many Thanks
Salvo
[email protected]

Salvo,
Here are some CPUs and their speeds:
2100+ 1.73GHz (TBred)
2200+ 1.8GHz (TBred)
2500+ 1.83GHz (Barton)
2600+ 1.9GHz (Barton)
2700+ 2.17GHz (TBred)
2800+ 2.08GHz (Barton)
3000+ 2.16GHz (Barton 333Mhz FSB)
3000+ 2.1GHz (Barton 400Mhz FSB)
3200+ 2.2GHz (Barton)
Take Care,
Richard

Graphic problems with k7n2 delta

I am having some problems with this motherboard. First, the booting, that doesn't work all the time. But the main problems happens with the graphics: the wallpapers doesn't show properly and some problems with the games also happen. Is it because of my graphic card (radeon) in conflict with the nvidia chipset?

wrong section, you need the 'AMD nVidia/AMD/SiS SocketA based board' section.
Hopefull a kind moderator will move your post

[nForce] Problem with K7N2 Delta 2 platinium

Hello!
I have just bought a MSI K7N2 Delt2 Platinium and I do not manage to solve a problem: the bios detecte no peripheral IDE!!! I tested two hard disks, a dvd reader, 3 different tablecloths, 2 connectors IDE... nothing of nothing: /
Moreover it puts to me like codes on the bracket: VR VV (horizontally).
If somebody could help me, I will be very grateful to him.
Thank you in advance for your assistance.

Hello,
Make sure the hard drives have a power cable plugged into them
In the BIOS are the IDE controllers enabled?
Enter the BIOS and go to Integrated peripherals
Then go to IDE function setup.
Make that
Onchip IDE channel 0 = enabled
and
Onchip IDE channel 1 = enabled
Then save and exit.
Turn the PC off.
Now using only 1 IDE hard drive, set it to master (jumpers on the back)
And plug it on IDE slot 0, make sure that the Blue end of the cable goes into the board.
And plug a power cable to the hard drive too.
Now turn the PC on and what happens?
Does it detect that hard drive?
Also could you post your PSU details on the sticker, eg
400w
+12v = 13a
+5v = 30a
+3.3v = 28a

Problem with K7N2 delta :booting issues

my k7n2 wont boot after being unplugged from power unless i reset the FSB jumpers to 100mhz mode. Also, it wont boot when I try to set the ram-FSB ratio different. It will not boot and I have to clear the CMOS to get it to work again. Please help

Quote
Originally posted by bdjohnson
my k7n2 wont boot after being unplugged from power unless i reset the FSB jumpers to 100mhz mode. Also, it wont boot when I try to set the ram-FSB ratio different. It will not boot and I have to clear the CMOS to get it to work again. Please help
How about some info regarding what you are using in the system? We don't have the ability to peer into your office/home to see what's in your system...
If you read the sticky posts at the top of the forum first you may find that you might answer your question first...alternatively do a search regarding your problem and you may find posts that will help you to find answers as well...
Bonz

Radeon 9000 problems with K7N2 Delta ILSR

when i try to boo the system the monitor gets turned off by the machine when it gets to the windows logon screen... the card is a connect 3D card and is the 128mb variation.. any ideas whats wrong???

Have you updated / backed out the drivers for the card at any point? I had this happen with a Sapphire card, it will only run with 1 ancient specific version of the driver.

Kingston, Crucial, Twinmos memory has problem with K7N2-DELTA??

Similar Messages

Maybe you are looking for