KM2M Powers Up-But nothing Else

Helping friend build new pc. PC boots, powers all devices but no video. Basically it just powers the devices and that is it.
Comp USA Power Supply 400 Watt 12volt 16amp.
Amd Athlon XP 2400. Even tried my xp 2700 wich i use so i know it works.
Generic Cd rom
western digital 40 gig, ide
HeatSink and Fan Retail
SdRam PC100 2 128 Mb
No sound from speaker either.
Any help would be apprecaited.
Thinking its a mobo problem, what cha think?

Was trying to use the onboard vid but then went to agp ati 128 rage pro when it didnt post the first 5 times. Went back and forth with the agp and onboard.
Not sure why the this board wont boot it is the power supply. Why is this board so touchy when it comes to power supplies?
12volt power connector is attached.
I tried both fsb settings.
Wd is alone, tried booting with no jumpers, and with default (the way it came) hell i even tried booting with it disconnected.
I have read the first 7 pages of this forum and im pretty disappointed with this board already(im glad i didnt buy it) but i am detemined to help my friend out. I havent got to read the part about the cruical ram yet, i did see someone talk about it being crap, witch i totally dissagree with, and im not sure what is in his machine.
Anything else i can try?

Similar Messages

  • Powers Up but nothing else!  HELP!

    Hello, I am trying to fix my wife's 2003 PowerBook G4. It starts up, have the fan and drive noise but it just goes to the white/gray screen with the apple logo and the circle running below it. It won't leave this screen just keeps making the running noise. I tried to reset. Pretty sure I did it right, but still have the same problem.

    Welcome to Apple Discussions!
    First, try booting while holding the SHIFT key. Keep holding until you get a message about "safe mode" or you get a normal desktop. This does some directory checking. If you get a desktop, don't try to use the computer as none of the extensions for special functions have loaded. Instead, restart normally and see if the desktop returns.
    If that does not work, you need to insert the system CD/DVD, either the grey one that came with the computer or a Mac OS retailer install disk. If the computer boots, that indicates that the major hardware in reasonably good and the problem is more likely with some corruption on the hard drive.
    If the computer boots from that system disk, it will present you with options to reinstall. Don't. Instead, look in the installer's menus for the option that lets you launch Disk Utility (DU) and run it. In DU, highlight the PowerMacs' hard drive and select "Repair Disk form the First Aid tab.
    In the profile, the OS on the PowerBook is listed as "Other." If its not a MAc OS, what is it? The instructions I posted are for a computer running a version of Mac OSX.

  • When I power up my mac, I see the white screen and the apple icon. After a few seconds of powering up the screen goes dark. Yet I still can the mouse arrow but nothing else.

    When I power up my Imac, I see the white screen and the apple icon. After a few seconds the screen goes dark. I am able to still see the mouse arrow as I move it around. But nothing else. What is the problem and how do I recover?

    Try this from another user:
    1. Shut the computer down by holding the power button for 10 seconds
    2. Restart the computer and press shift at the same time until you see the progress bar start moving
    3. Once you reach the point where your screen goes dark and you see the cursor, type the first letter of the username for your computer, then hit Enter, then type your password, then hit Enter.
    4. After a moment, you should see the spinning beach ball
    5. Your screen should then move on to something along the lines of "Completing OSX Installation" (I can't remember the exact wording). Let it finish. After that it should go to your normal desktop and the issue should be fixed. (If your screen goes pitch black during this process, hit the space bar. I thought it wasn't working, but the screen was just sleeping).

  • HELP NEEDED!! I bought a brand new mac air 11 inch a month ago, and for three days now I can't switch it on.when I do, i can hear the machine is on, but nothing else happens. (yes it is charged). please help

    HELP NEEDED!! I bought a brand new mac air 11 inch a month ago, and for three days now I can't switch it on.when I do, i can hear the machine is on, but nothing else happens. (yes it is charged). please help.
    I bought it in South Africa and I am currently in Israel.

    thank you for the response.its not working, tried that. i can switch the machine on and off, can hear the machine when i hold it to my ear. but nothing works, not the screen, not the sound, nothing.

  • I am trying to install my CS4 Suite onto new PC with Windows 8.  It installed Photoshop but nothing else.  It is asking me to "Install with 'setup.exe'"  Which i dont think is on there.  Is there a way around this?  Thanks in advance.

    I am trying to install my CS4 Suite onto new PC with Windows 8.  It installed Photoshop but nothing else.  It is asking me to "Install with 'setup.exe'"  Which i dont think is on there.  Is there a way around this?  Thanks in advance.

    Run the cleaner tool and reinstall with sufficient user privileges and security stuff turned off. Your install went wrong because you didn't consider this.
    Mylenium

  • My first gen 3g iphone photos are not recognised by camera wizard - it sees the phone but nothing else no files - it is not locked - ?

    I have a new 4g Iphone - Telstra (Australia)  disabled my old 3g and enabled the 4g so the 3g is just enabled to show contacts and photos etc.
    I want to download my photos and contacts from the 3g.  trouble is that my internet is dial up only at home and impossible to use as too slow.
    So my itunes is now out of date (not current module 10.5 + etc.) and the 3g phone is also not operating on the latest ios.
    BUT the itunes does sync the phone - but it seems to only sync from computer to phone - so my camera roll on the 3g is not on my computer - therein lies the dilemma - I don't know how to download the photos.  I cannot update the ios on the 3g and it seems that might be reqired to "back up"
    So first question is how do I back up (not sync) my 3g to itunes.
    Do I need to updates its ios first and update iteuns first (in which case thats impossible)
    So what else could I do.
    It seems the other thing is that even if I could back up the 3g the Itunes won't recognise the 4g as the 4g is ios 4 or something and the itunes is not up to date.
    SO I thought I should just use camera wizard or a photo package like iphoto or kodak easy share.
    But with camera wizard my computer recognises the 3g phone BUT nothing else.  It is greyed out for options, and ini Windoes Explorer it shows it as a camera but when you right click it has no "properties" - and no files show up at all...
    it is like it seems the camera and then nothing else.
    THE CAMERA is not locked.
    WHAT shoudl I do?

    also - when I use camera wizard it just tells me the phone is busy or in use  and I should retry.
    If I use it through windoes explorer - it shows me the camera to computer symbols and a line moving between then but bombs out saying camera is busy.

  • ACE 4710: Possible to allow a user to clear counters but nothing else?

    Hello all,
    Using an ACE 4710 we have a user setup with the Network-Monitor role which allows the user to view config, interface status, etc.  We would also like to allow this user to clear the interface error counters as well, but nothing else.  Is this possible?
    Thanks!

    Hello Brandon-
    Network-Monitor only lets you browse outputs, it is a not a role that allows a user to make any changes including clearing stats.  You can create custom roles and domains to get closer to what you want, but you cannot zero in on a single command like that.
    i.e.
    ACE# conif t
    ACE(config)# role MyRole
    ACE(config-role)# rule 1 permit modify feature ?
      AAA             AAA related commands
      access-list     ACL related commands
      connection      TCP/UDP related commands
      fault-tolerant  Fault tolerance related commands
      inspect         Appln inspection related commands
      interface       Interface related commands
      loadbalance     Loadbalancing policy and class commands
      pki             PKI related commands
      probe           Health probe related commands
      rserver         Real server related commands
      serverfarm      Serverfarm related commands
      ssl             SSL related commands
      sticky          Sticky related commands
      vip             Virtual server related commands
    You can create a permit or deny rule, within that, create/debug/modify/monitor each feature seperately.
    Domains allow you to create containers for objects.  You can place specific rservers, serverfarms, etc. into it - then apply it to a role so that the user assigned to it can only touch those objects.
    Regards,
    Chris Higgins

  • TS1702 Maps program does not work. In standard it only shows a grid. If I ask for a route it shows start and end point and three route boxes but nothing else. It does show directions. If I switch to hybrid it shows to routes but no roads. Background is a

    Maps program does not work. In standard it only shows a grid. If I ask for a route it shows start and end point and three route boxes but nothing else. It does show directions. If I switch to hybrid it shows to routes but no roads. Background is a blur.

    Do you have a question? This is a user to user help forum. Apple is not here only other users like yourself. You don't report problems to Apple here.
    By the way, it might help if you indicated where you are located.
    To complain to Apple use http://www.apple.com/feedback/ipad.html

  • I can print a test page from my Mac to my HP Officejet Pro 8600 but nothing else will print

    Hi - I just recently had a hard drive crash and had to revert to an old Time Machine backup on my new hard drive to get my Mac back.  Since getting back up and running I have been unable to get my Officejet Pro 8600 back online.  My computer is wired to the wireless router but the printer is running wireless.  My computer can see the printer just fine and I can even print a "Print Quality Diagnostic" report from my Mac to the printer from the HP utility.  But nothing else will print.  The firmware is up to date.  I have tried resetting the printing system multiple times, rebooting the machine, etc... Nothing works.  Any help would be appreciated.  
    If it helps, we were using a different printer the last time the time machine was backed up, so when we used that backup the old printer was showing, but I reset the printing system, so it shouldn't matter.  
    Thanks for your help!  

    Hello @Ryan221,
    Welcome to the HP Support Forums! I see your hard drive recently crashed and now you are not longer able to print to your HP Officejet Pro 8600. I see you have reset the printing system with no success. Let's try a different approach:
    Scrub/ Uninstall
    • Open the Applications folder > HP or Hewlett Packard folder > HP Uninstaller
    • Click continue, click on one of the printers in the list.
    • * Only do this step if you do not have any other HP Printers. Hold down Control, Option and Command, While holding the three buttons down,
    • Click uninstall.
    Reset Printing System
    1. Click the Apple icon (   ), and then click System Preferences.
    2. In the Hardware section, click Print & Fax/Scan. The Print & Fax/Scan  dialog box opens.
    3. Right-click (or  Ctrl  +click) in the left panel, and then click Reset printing system…
    4. Click OK to confirm the reset.
    5. Type the correct Name and Password.
    6. Click OK to reset the printing system. The Print & Fax dialog box shows no printer selected
    Note: This will remove all printers in the print and Fax/Scan, any printer removed can be re-added later by clicking the plus (+) symbol..
    Repair Disk Permissions
    1.On the Dock, click Applications, and then click Utilities.
    2.Double-click Disk Utility.
    3.Highlight your hard drive/partition on the left (by default this is "Macintosh HD").
    4.Click the Repair Disk Permissions button at the bottom of the window.
    5.Once the repair is complete, restart the computer.
    Restart the printer. Now you can download and install the printer software and install it. Click on the link below to begin the download and follow the on screen instructions:
    HP Officejet Pro Full Feature Software and Driver - Mac OS X 10.6, OS X 10.7, OS X 10.8
    I hope this helps, please let me know the outcome!
    HevnLgh
    I work on behalf of HP
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

  • After turning on iMAC the sign in page comes up and accept my password. It then goes to a page with a background pictures but nothing else. If I leave it there it eventually fades and shows the clock.  How to I get it to open from there?

    After turning on iMAC the sign in page comes up and accept my password. It then goes to a page with a background pictures but nothing else. If I leave it there it eventually fades and shows the clock.  How to I get it to open from there?

    Hello,
    See if it'll Safe Boot from the HD, (holding Shift key down at bootup).

  • Under TV Shows there used to be favorates, search and so one, for reason, just "My TV Shows" shows up but nothing else.

    Under TV Shows there used to be favorates, search and so one. for some reason, just "My TV Shows" shows up but nothing else.  I can't look up top shows, look at my fav shows, or even search up shows any more.  I restored my apple tv factory settings but it was still missing.  Pior to doing that I pulled the power cord and reset my networks... and still noting, please help....

    Welcome to the Apple Community.
    Yes there are quite a few similar reports at the moment, I haven't experienced the problem, yet others in the UK have, so we're not quite sure what criteria determines whether you are affected by this. I haven't seen any solutions so far, so it may just be a case of waiting to see if it's repaired or whether the rest of us are going to see the same thing.

  • The bookmark feature has stopped working, I can only bookmark my homepage (google search) but nothing else.

    Firefox is simply unresponsive when I try to save a page as a bookmark, I have tried clicking the star in the URL bar, using ctrl-D, right clicking on the page, and saving from the bookmarks tab. None of these options do anything at all.
    I have tried turning off different add ons but have not had any success. The only time I can get it to save a bookmark is if I bookmark my homepage, then it will save that, but nothing else.

    This can be a problem with the file places.sqlite that stores the bookmarks and the history.
    * http://kb.mozillazine.org/Bookmarks_history_and_toolbar_buttons_not_working_-_Firefox

  • I cannot open itunes on my mac.  The Icon jumps, but nothing else happens.

    I may have shut my computer off while a new version of Itunes was downloading.  Not sure if this would affect it, but I can't open it now.  When I click on the icon, it jumps a little, but nothing else happens! Any ideas?? Help! I can still open it on my iphone. 

    Boot from your Snow Leopard install DVD, run Disk Utility and run Disk First Aid.
    Reboot.
    Then Apple menu > Software Update.
    Then reinstall iTunes.

  • Facetime works with USB UVC gearhead webcam but nothing else does

    I have a gearhead USB 2.0 webcam that facetime easily see but nothing else does
    It is a model WC4750AFB from gearhead it uses USB 2.0 Connectivity with UVC and Facetime sees it but I can not get any other applications to use it
    Why can one app on my mac mini find and use it suxxesfully and others can't. This is really stupid. There is no basic instruction onhow to setup facetime or find out how it can see the webcam and it would be nice to know so I can get it working with my other app on my MAC mini

    Logitech - HD Webcam C615
    http://www.bestbuy.com/site/logitech-hd-webcam-c615/2588445.p?id=1218337862339&s kuId=2588445
    Logitech - C920 Pro Webcam
    http://www.bestbuy.com/site/logitech-c920-pro-webcam/4612476.p?id=1218501788204& skuId=4612476
    I know FOR A FACT that those two WILL WORK with Mt. Lion and ALL Mac Apps that use a cam.
    Skype too.
    I really like the 920. It shoots in 1080p HD. EXCELLENT picture quality and video quality.

  • Ok, tried message boards everywhere to try and figure this out before having to post a question. Have a 21.5" iMac running Snow Leopard 10.6.8.  After updates no wireless capability for ipad or laptop, imac connects fine but nothing else.No widgets work.

    Ok, tried message boards everywhere to try and figure this out before having to post a question. Have a 21.5" iMac running Snow Leopard 10.6.8.  After updates no wireless capability for ipad or laptop, imac connects fine but nothing else. No dashboard widgets work, Skype won't work. What goes?

    Your post is pretty lengthy and I have to admit I didn't read it all. Please try restarting in Safe Mode, if that doesn't work please do both a SMC and PRAM reset. These may take 2-3 attempts.
    SMC RESET
    Shut down the computer.
    Unplug the computer's power cord and all peripherals.
    Press and hold the power button for 5 seconds.
    Release the power button.
    Attach the computers power cable.
    Press the power button to turn on the computer.
    PRAM RESET
    Shut down the computer.
    Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    Turn on the computer.
    Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
    Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    Release the keys.

Maybe you are looking for

  • Purple triangle always ends at 1:06:30 problem

    I familiar with GB3 and have been doing podcasts with it for a while. Easiest for me to work is I just open the last podcast i did and delete the audio, add new audio and do new voiceovers since the theme is the same. Then save everything and export

  • Using ASP with Dreamweaver

    I'm sorry, I'm a n00b at this... as soon as I get the link, I will have access to my website files from the host. From there I want to update the website. The tech at the host says I need to be knowledgable with ASP, which I'm not.... I've read a lit

  • How to set up 81/2 x 11 document to fold to 5 1/2 x 11?

    I am so frustrated.... I have worked in Pages before and alwasy seem to figure it out. However, I am stumped on a very easy, thus irritating, problem. I am creating a basic 8 1/2 x 11 Brochure that will be 2 sided and fold to 5 1/2 x 11. I only want

  • PDF version control

    For version control can a PDF auto delete or can a watermark appear after a period of time? I'm looking to distribute PDFs to external customers.

  • Upgrade or Full package

    I am intending to upgrade to CS5 from DW8. I can get a teacher discount. Can't find an upgrade for teachers, just the full version. Should I uninstall DW8 before adding CS5?