KM4M board will not display graphics

...except in safe mode..
This is on a brand new build with Win98SE on the HDD
Upon installation I loaded all drivers from the MSI disc.
This is what happened after the drivers were loaded-
The system posts,runs through the splash screen and the screen goes black.
If I go into the device manager,remove the VIA/S3G Unichrome graphics display adapter,reboot the PC will boot up, discover the PCI-compatiblr graphics display, etc and proceeds to the message directing me to restart to finish setting up my hardware.
Upon reboot the screen, ends up black again.
My best two guesses are something wrong in the BIOS or bad board, and I have checked the BIOS over as best I can.
Help???

In addition to the video problem I also have a internet connection problem.
The entire system now freezes upon dial up connection. Feel free to split this thread if you do not want to try and deal with both problems in one.
I have put a Cirrus Logic video card in PCI slot 2 and now I do have video, but I need the onboard to be workin instead
In the device manager there is a question mark beside
Complete specs to the best of my ability; keep in mind I did not choose the HDD or periperals, they are what I have to use.
AMD Athlon CP 2000+ with stock heatsink and fan- not OC
Kingston 256mg DDR
WDC 3gig HDD formatted FAT32 with existing Win98SE
Rexpower PX350 350 watt pws designed for k/7 k/8 p4 boards
3.3 - 20a
5.0 - 40a
12.0 - 16a
Conexant V92 voice/ data/ fax modem
Things I have done so far;
Video;
I have reinstalled all drivers from the OEM disc
I have installed the cirrus logic as I mentioned
I have swapped out the KM4M for another new KM4M with the same result, so I can only assume it is something I am doing wrong ( I am building two of these systems with the same board)
Modem:
This computer was on a cable network at its place of business, + the modem would work when it was still connected.
I have swapped out the modem with the same results
I have run AVG w/viruses found and deleted viruses
I have run Spybot and Adaware with spyware found and deleted
I have cleared, temp and temporary files
On occasion it will allow me into IE6 or Netscape for 1 minute or so.
With the exception of these two things the PC is running great.
Thanks again.
Quote
Originally posted by osnavi
Give complete PC specs. includding P.Su.'s brand and AMPS it gives to 3.3v. 5v. and 12v. rails.

Similar Messages

Firefox will not display graphics.

on some web sites the graphics are just gray boxes, others like the blaze the graphics are just not there.

*Check the permissions for the domain in the current tab in "Tools > Page Info > Permissions"
*Check that images are enabled: Tools > Options > Content: [X] Load images automatically
*Check the exceptions in "Tools > Options > Content: Load Images > Exceptions"
*Check the "Tools > Page Info > Media" tab for blocked images (scroll through all the images with the cursor Down key).
If an image in the list is grayed and there is a check-mark in the box "Block Images from..." then remove that mark to unblock the images from that domain.
There are also extensions (Tools > Add-ons > Extensions) and security software (firewall, anti-virus) that can block images.
*http://kb.mozillazine.org/Images_or_animations_do_not_load

The "week" display for Calendar is screwed up. The whole week of days will not display.

The "week" display for Calendar is screwed up. The whole week of days will not display.

Sounds like a different problem but:
Since these threads aren't merged, I'm posting the same in several threads.
I've had the screen blank problem, the sound and copmputer were still on. I took the IMac in twice, got home, still not fixed.
But they used their own keyboard in the shop and couldn't reproduce the problem. I switched keyboards and so far so good. It's been 3 days now.
I'll keep folks updated. Don't get a new graphics card before you try a new keyboard.
Be sure to take the batteries out of your keyboard when testing another one as the board does not turn off if it is like mine.

Satellite A300 PSAG0A - Games Will Not Display in Full Screen Size

I have a large number of games installed on my computer. At least 90% of them will not display in full screen size but display in a small window with a large amount of black screen surrounding the window. I am running Windows Vista Home Premium 32 bit. However, I do not think it has anything to do with Windows as my husband runs the same games on his Toshiba Satellite L300, running exactly the same version of windows, and they all display in full screen size.
Altering the screen resolution makes no difference. And, of course, I do select the full screen option in the games.
Also, sometimes when I have been playing a game and then closed it I find that my desktop picture has shrunk to the smaller size - the same size as the window in which the game was displayed when I was playing it.
The games work fine in every other way, it is only this small screen size which is driving me nuts.
I hope that someone can help me with this!!

Yes, as far as I can tell I have the latest driver. But, even this is confusing to me because....
My graphics media accelerator is Mobile Intel(R) 965 Express Chipset Family. The installed driver version is 7.14.10.1329. The release date for this is 2007-09-13, as far as I can tell from web searches.
However, on the Toshiba website for driver downloads, the available driver version is 8.2.0.1012 PV. The date is 2006-12-28. I have downloaded this driver and attempted to install it. I get the message that it has been installed but, after rebooting and checking the installed driver version is still 7.14.10.1329.
Perhaps, the 8.2.0.1012 PV version does not actually install because it is older than the currently installed version. I would have thought that the driver version with the higher number would be the newer one, but perhaps this is not the case as the dates do not seem to support this theory.
So now I ask myself, firstly, if the driver available for download on the Toshiba website is not the newest one, then why is it there?
Secondly, if it is the newest one then why will it not install on my computer?

Adobe Premiere Elements 13, will not display video picture, audio only. My video format is listed as compatible with Adobe.

Adobe Premiere Elements 13, will not display video picture, audio only. My videois listed as compatible with Adobe.

douglass
On what computer operating system is your Premiere Elements 13 running? Have you updated 13 to 13.1 yet using an opened project's Help Menu/Updates?
If not, please do so.
You have not given us enough information with which to help you.
What are the properties of your source file that is presenting in the project with audio but no video?
Quickest way to gain that information is from brand/model/settings of the camera that recorded the video.
I am looking for
video compression
audio compression
frame size
frame rate
interlaced or progressive
file extension
pixel aspect ratio
What does the file's thumbnail look like in Project Assets after it is imported....thumbnail with no image (gray), thumbnail with only an audio icon
within it, or other? On the Timeline, what do you see represented in Video 1....nothing as opposed to Audio 1 where you see the audio portion of
the file?
Do you have the latest version of QuickTime installed on your computer along with Premiere Elements 13/13.1? Are you running the programs as
administrator?
Is your video card/graphics card driver version up to date according to the web site of the manufacturer of the card?
Let us start here. Based on your reply details, we will customize troubleshooting strategy for you.
Thanks.
ATR

Page will not display properly with inline Frames

I have a html page that will not display properly in Dreamweaver. I have a basic understanding of html and want to be able to edit a website in Dreamweaver that was given to me. It looks fine in a browser, but in Dreamweaver some of the content is missing and displays the following message, "Your browser does not support inline frames or is currently configured not to display inline Frames". I was able to open it without any problems using Microsoft Front Page, so is it possible to view and edit it in Dreamweaver?

Without seeing your page, I'm guessing that your page contains server-side includes, iframes and scripts to other files on the server that populate page with content on the server's end. You can't see it in DW because you don't have all the files in your DW local site folder. You said this views fine in FP. Was your page created in FP with FP proprietary tools?
Nancy O.
Alt-Web Design & Publishing
Web | Graphics | Print | Media Specialists
www.alt-web.com/
www.twitter.com/altweb

Z97 PC MATE - Second GPU will not display / black screen

Using Z97 PC MATE with 2 nvidia cards (GeForce GTX970 and GeForce GETX750ti). My goal is to use the 750ti for dual display with the 970 reserved for compute in a 3D software package (houdini simulations). If both cards are installed on the mobo and one monitor is plugged into the 750ti, it will not display, not even the BIOS screen. Also there is no audio, there is normally a chime when the OS lock screen is reached and that never plays.
The 750ti is plugged into the PCEe 2.0 slot, the 970 the 3.0 slot. Both cards can display in their respective buses by themselves if only one card is installed. If both are installed, the 970 will output a display as expected. I have also tried an older quadro card in the 2.0 slot and it also defaulted to the 970 in the 3.0 slot. With one display plugged into the 970, and one in the 750ti I have gotten an image to display on the 750ti. But never with only one monitor plugged into the 750 attempting to use that card as the main display.
I have used m flash to update the bios to 4.6, but I never used the disc which came with the mobo to update. I thought maybe there is a GPU display priority in the BIOS but I'm not seeing it. I see there is a way to prioritize UEFI and legacy, and Gen1, 2 or 3, but don't know how that should be set up for this (if that is the problem). I would think if that were the case though the audio at the lock screen would still play, but I don't know.
My current nvidia driver version is 342.22, I am using Ubuntu 14.04 as linux OS operates better with the software I am using. I have also posted to the Ubuntu forums about this, but thought I would post here because the BIOS screen doesn't display which makes me think it could be hardware related. Although all of the hardware is detected properly and appears to be functioning as expected.
This issue was reproduced with and without the HDD connected.
Hardware:
i7 4790k
EVGA GTX970 and EVGA GTX750ti
Z97 PC MATE
32gb PNY DDR3-1866 240-pin DIMM
Antec Truepower Classic 750w gold certified
PNY Optima 480gb SSD - PNY SSD7SC480GOPT-RB
Hitachi 2TB ultrastar HDD
I am not sure at this point how to continue troubleshooting this issue, or if this is not possible for this mobo and I just didn't recognize that. One test I was considering is putting the 970 in my old computer (MSI 970FX-GD70) and seeing if the results are the same. Will post any additional required information.
thanks!

Did you install your graphic driver when both vgas are on? Let the driver detect both vga then you can just switch cable and display well. Use the latest 344.65 driver. As for the 3D package, you need to make sure the software support or can change the settings that which vga to compute.
But there's one thing I need to make sure first, does your vga work with only one vga on pcie 2.0 slot? Just wanna be sure it's not faulty slot...

Firefox will not display videos since Yosemite migration

Good day!
I run an early 2011 15" MacBook Pro, 2,2 GHz Intel Core i7 with 4g 1333 MHz DDR3 Memory, and an Intel HD Graphics 3000 with 384 Mo. Firefox is 34.0.5.
Since I migrated to Yosemite (10.10.1), the browser I use (Firefox) will not display the videos, but plays the sound out of them...
I tried to clear the PRAM (NVRAM) with the Command (⌘), Option, P, and R, but it doesn't work. I even tried to shut down the graphic acceleration option in Firefox, to no avail...
What else should I do? Any solution out there?
Thanks, and Merry Christmas to you all!
Martin

    System Preferences > Flash Player > Advanced > Delete All
     Press the "Delete All" button.
     Install Adobe Flash Player.
    http://get.adobe.com/flashplayer/
   Download it first.
   The next step is important.
   Click Safari in the menubar and select “Quit Firefox.
    Follow the prompts and install it.
    Restart computer.

Banner image will not display in Dreamweaver; can you help?

Banner image will not display in Dreamweaver; can you help?

If the banner image is not displaying, it is either not in an acceptable web file format (optimized for web as jpg, gif or png). Or it is corrupted. Or the path to the image file on server is broken.
It's impossible to say more without a link to your problem page.
Nancy O.
Alt-Web Design & Publishing
Web | Graphics | Print | Media Specialists
http://alt-web.com/

The menubar will not display in full screen

Hi.
I have a strange problem in fullscreen mode, on my Macbook pro 15"
I LOVE fullscreen, and infact the next macbook I will get is the 11" air because of its size and because full screen is so nice to work with.
But I have a strange problem which I can't find a solution for.
Suddenly the menubar will not display it self when I move the mouse to the top of the screen. The only way I can access the menu bar is by exiting full screen (ctrl + Cmd + F) and the toggel it back on after I have used the menubar
This actually makes fullscreen mode useless and its driving me nuts, because this should not happen on Apple software. I would expect these sorts of behaviour on windows but not in osx.
Anybody have a hint about what to do?

https://discussions.apple.com/thread/3881124?start=0&tstart=0 <<<<< GO THERE
Try this: make a temporary, backup copy (if you don't already have a backup copy) of the library and try the following:
1 - delete the iPhoto preference file, com.apple.iPhoto.plist, that resides in your
 User/Home()/Library/ Preferences folder.
2 - delete iPhoto's cache file, Cache.db, that is located in your
 User/Home()/Library/Caches/com.apple.iPhoto folder.
Click to view full size
3 - launch iPhoto and try again.
NOTE: If you're moved your library from its default location in your Home/Pictures folder you will have to point iPhoto to its new location when you next open iPhoto by holding down the Option key when launching iPhoto. You'll also have to reset the iPhoto's various preferences.

I was recently sent a very large emoji message amd now when i try to acces messages it will not display mesagges and then will bring me back to the home page

was recently sent a very large emoji message amd now when i try to acces messages it will not display mesagges and then will bring me back to the home page

Quit the messages app and reset your phone.
Go to the Home screen and double click the Home button. That will reveal the row of recently used apps at the bottom of the screen. Tap and hold on the app in question until it jiggles and displays a minus sign. Tap the minus sign to actually quit the app. Then tap anywhere on the screen above that bottom row to return the screen to normal. Then restart the app and see if it works normally. Then reset your device. Press and hold the Home and Sleep buttons simultaneously ignoring the red slider should one appear until the Apple logo appears. Let go of the buttons and let the device restart.
After the phone restarts go into Messages and delete the thread containing the problem message.

Newly created images will not display in Firefox 8 for Mac. Same images appear in other browsers. Why?

1. Specific new images are uploaded but will not display in Firefox 8 on my Mac with OS 10.6.8. (Does appear in other browsers, e.g., Chrome and Opera, and appears on Firefox 8 for PC.) Also, other images on the page display.
2. I have cleared cache, cookies, etc., in Recent History, and restarted both application and computer.
3. I've tried creating GIF, JPG and PNG, but none show on the page in Firefox on my Mac. I can see the offending image in other browsers such as Chrome on the same computer, and on Firefox on PC. Offending pages are in both PHP and HTML: http://www.brookfieldcivic.org/advertisers.php and http://www.brookfieldcivic.org/advertising_freedom_montessori.html
Image links: http://www.brookfieldcivic.org/images/advertisers/freedom.png and http://www.brookfieldcivic.org/images/advertisers/Freedom_Montessori_bizcard.jpg

You can use these steps to check if images are blocked:
*Open the web page that has the images missing in a browser tab.
*Click the website favicon ([[Site Identity Button]]) on the left end of the location bar.
*Click the "More Information" button to open the "Page Info" window with the Security tab selected (also accessible via "Tools > Page Info").
*Go to the Media tab of the "Tools > Page Info" window.
*Select the first image link and scroll down through the list with the Down arrow key.
*If an image in the list is grayed and there is a check-mark in the box "Block Images from..." then remove that mark to unblock the images from that domain.

Firefox will not display on the screen even though with Process Explorer I see Firefox.exe active but no CPU usage

I use Firefox v10.0.2 as default browser on Dell XPS8300 e/w Intel Core i5 & Windows 7 Ultimate and Compaq Presario CQ57 e/w Intel Core i3 & Windows 7 Home. More frequently on the (about 90% of attempts) than the Dell (50% of attempts) Firefox will not display to the screen when I click on icon. When it happens I cannot display other programs. I specifically say display because I believe Firefox has started. To circumvent the problem I installed Process Explorer on both machines and start this program first then click on Firefox icon. When problem occurs I can see Firefox.exe process in Process list; some CPU consumed but, then, no CPU activity. If I click on Firefox icon again another process opens in Process list but with same response - some CPU consumed and then no CPU activity. If I have 2 processes running and kill the 1st process, the 2nd will display and everything from then on is normal. If I do not open a 2nd process but kill the 1st process then click on Firefox icon Firefox is displayed and everything from then on is normal. This problem has occurred since original installation on both new machines. I've updated video drivers in both machines.

Ok, let's see if we can fix this and get it working for you!
First, if you start Firefox in [[safe mode|safe mode]] (restart your computer first, then when you open Firefox, hold down the shift key) does it start up more reliably? This is usually caused by a faulty add-on. If it does help, then restart Firefox, go into the Firefox button, then add-ons, and disable your extensions one by one until you find the trouble maker.
Also, try updating to Firefox 11, it has several bug fixes that might make life easier here.
Just as a few basic troubleshooting steps to make sure we have all the bases covered,
Run all Windows Updates, install all needed service packs, etc.
Update all your plugins (Flash, Java, etc.): [http://www.mozilla.org/plugincheck/ http://www.mozilla.org/plugincheck/].
Download and Install MalwareBytes Anti-Malware, run a full Scan. [http://www.malwarebytes.org/ http://www.malwarebytes.org/]. This helps check that there are no viruses on your computer causing issues. you can uninstall this program after you clean off any infections.

Updated to the latest revision. Firefox will not display my chosen home page without clicking on home icon.

Since latest update...Firefox will not allow a new page to be opened from a link in a current page. It will allow a new tab to be opened (with tabbed browsing checked) but i prefer a new page. Even in tabbed browsing links to things like a pdf will not work at all.
Firefox WILL NOT close. X-ing out will close the window but I can not get back to Firefox without closing it in task manager.
Firefox will not display my chosen home page without clicking on home icon.

Start Firefox in [[Safe Mode]] to check if one of the extensions or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox/Tools > Add-ons > Appearance/Themes).
*Don't make any changes on the Safe mode start window.
*https://support.mozilla.org/kb/Safe+Mode
*https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes

Adobe Illustrator file will not display correctly when logged in as a user

I am working with an Adobe Illustrator CS2 file that will open and display correctly if I log in as Administrator, but will not display correctly if I am logged on as a user. The error message is that there is not enough memory to display the file correctly and I am forced into preview mode. The user Home folder is on a server. Other than this, I have made certain that the criteria for opening the file match under both interfaces. I have opened the AI CS2 file on other Macs and it opens fine. I conclude that the problem is with the user Home folder, but beyond that, I'm stumped. Any help will be appreciated.

After I filed a bug-report an Apple engineer contacted me, and asked me to try running java in headless mode: http://java.sun.com/developer/technicalArticles/J2SE/Desktop/headless/
That solved the problem!

KM4M board will not display graphics

Similar Messages

Maybe you are looking for