KT3 Ultra 2 -C motherboards pc3200 ram support ?

Hi, I'm using Kt3 Ultra 2-C motherboard and pc2700 ram added on it. I think to add pc 3200 ram.  Can I use side by side both ram. Thanks.

You can, but if you find problems, you'll know where they come from. BTW the faster memory will degrade to slower mem. speed. Also, if you'r running a 333FSB CPU. memories will run at that max.speed.

Similar Messages

  • Experience with kt3 ultra 2/r and corsair rams??

    Has anybody tried the kt3 ultra2/r with
    256MB CORSAIR DDRAM (PC2400)
    (CM64SD256-2400C2H 300 MHz CAS2) Rams??
    I faced lots of problems on my soyo dragon plus... ?(
    Does anybody know if this mobo supports PC2400 as well??
    thanks a lot in advance..
    best regards,
    drosche

    No, my Ti4400 is not the Champ ed. The actual model number on it is 8871 ver-1.00. You can read about my problem's in the "Have you seen this?....." thread on this forum (page 7 now I think)
     I haven't had a problem in the last couple days though. I removed some Reg tweaks (this is a DAW box) and ....dont luagh, turned up the heat in my house. I'm not sure if it was the Reg edit or Temp, but things are working ATM.
    Nice to know I'm not alone though,
    C

  • Problems with KT3 Ultra (MS-6380E)..please help

    Hey all-
    Here is my system configuration:
    MSI KT3 Ultra MS-6380E) motherboard
    AMD Athlon 2100+ XP cpu
    (2) 512mb PC2700 DDR ram (1 gig total)
    (2) 120gb Western Digital 7200rpm Harddrives (240gb total)
    Nvidia Geforce Ti 4600 video card
    Creative Labs Sound blaster Audigy Platinum
    LG 32x10x40 CDRW
    16x DVD ROM
    400 watt power supply
    Here is my problem:
    Just built the machine, checked every plug and everything and when I turn on the machine I got no screen, no post, no beeps, nothing.
    So I turned the machine, and cleared the CMOS.  Turned the machine back on and got post , went into the BIOS, set the time,date, yada yada, all the drives were detected fine.  I went in the Frequency/Voltage Control screen and the "CPU FSB Clock" was set to 100 mhz, "CPU Ratio" was set to Auto as was the "CPU Voltage, DDR Voltage, and AGP Voltage".  I saved settings and rebooted but then I didn't get a screen, no post, no beeps.  
    I tried clearing CMOS again, turned machine on, got back in the BIOS just fine.  I tried setting the CPU FSB Clock to 133mhz and left everything else on Auto.  Rebooted and once again ..nothing.. no screen.
    I don't understand what the problem could be.  It seems that I can only get a screen when I clear the CMOS.  But even if i use the "Load BIOS Setup Defaults" or even the "Load High Performance Defaults" I still get no screen or anything when I reboot.
    Can anyone help me here?  I have never run into this before.
    Thanks in advance!!
    Joe

    If it is only doing it when you turn your bus speed of 100 up to 133 for the xp processor then I have had the problem.  If you are booting with a bad cpu that isn't working properly (can't run at 133)  then the computer will not POST.  As soon as you clear the cmos it sets the speed back down to 100 for failsafe.  If you try to boot a duron processor like a 700 or something on fsb 133 then the motherboard won't post.  Make sure you don't have a duron processor instead of a athlon xp or a bad cpu.  I would recommend taking it to the place you bought it or else an autorized amd spot.  They should be able to throw in another proc and check it out.

  • KT333 - KT3 Ultra MS-6380E CPU FAN PROBLEMS

    Yesterday I installed my new motherboard:
    Athlon XP2000+
    KT333 - KT3 Ultra MS-6380E
    256Mb DDR RAM Running at 266Mhz
    MSI Geforce 4 Ti4200 64Mb DVI TV AGP Graphics
    Everything was installed correctly and when I switched on my pc, the bios was reporting CPU FAN not running.
    I checked my connection on the motherboard and it was correctly connected up to CFAN1.
    After playing around abit, I tried connecting this to PSFAN1 and the FAN started spinning but the problem was still there.
    Why does my motherboard Fan on CFAN1 not spin??? But spins on PSFAN1??
    When my fan was on PSFAN1 it was also fluctuating but i guess thats because of my PSU which is 230 Watts (which i am going to upgrade today to 300W or 400W.
    Also with kit installed how can i set up my bios to run at its best?????!?!?
    Please help...
    Mits

    Hi,
    You probably have a high-speed-fan, and you blown the fan-header of the motherboard....
    Fan's like these need to be connected to the powersupply directly and only connect the sensor wire to the motherboard....

  • KT3 Ultra / Freeze

    KT3 Ultra
    XP 1700
    DDR 256 Ram
    80 Gig 7200 Maxor
    Xtasy MX 440 Graphics
    Was freezing all the time after upgrading bios
    Now it seems stable most of the time but
    I cannot play halflife thru GameSpy or directly thru
    Game Internet Play.
    Ran under win 2000 and now under win98
    Fast computer NO FUN!!
    Thanks for any help.
    Andy

    Dumped the MX440 (returned to store)
    Installed Radeon 8500 LE $20 more bucks
    Picked up about 1300 winmarks and been Halflifin
    with a smile.
    Man this mobo is a fickle sort.

  • Kt3 ultra no sound

      I JUST BOUGHT A KT3 ULTRA 6380E SERIES MOTHERBOARD AND AN AMD XP 2000 NO PROBLEMS WITH BOOTING UP BUT AFTER I INSTALLED ALL DRIVERS I, I HAVE NO PREFERRED PLAYBACK DEVICES FOR SOUND. SPEAKERS ARE PLUGED IN RIGHT AND IN THE RIGHT JACK. I HAVE NEVER HAD THIS PROBLEM BEFORE. CAN ANYONE HELP ME. I HAVE ALSO USED STANDOFFS ON THE BOARD TOO! X(  ;(

    Maybe you would like to try some of Micro$oft Win updates... it sometimes help, but before that double check everything in the System Hardware, check also for conflicts
    You don't say what Win version you have...

  • Does KT3 Ultra 2 support PC3200?

    I cannot locate the manual for this mobd, but was wondering if anyone knows if the KT3 Ultra 2 board supports the Kingston 512MB PC3200 DDR RAM? or am I stuck with PC2700 memory?
    My system is so unstable, locking up many times a day. The mobd. is a RMA replacement from MSI (due to secondary IDE problems). XP w/SP2 loaded fine, but PC hangs at bootup or usually within 30 minutes.
    Thanks.

    I don't have the PC locally now, so I cannot check the power supply manufacturer information.
    However, I can tell you that the power supply is brand new as is the case I just purchased. It may be an Austin 300W if my memory serves me right.
    I have gone through this website (http://www.msicomputer.com/support/sup_tshoot.asp) and forum and found the most likely causes of system hangs appears to be:
    1. old BIOS
    2. CPU problems
    3. memory mismatch/bad
    - The motherboard just came in from MSI as an RMA replacement, so the BIOS is probably the latest (5.7). I will verify this weekend.
    - The CPU is newer, so it is not likely. Although, I can swap it  and try it out this weekend.
    - I know for a fact that the memory is from different manufacturers. I have 256MB and a 128MB PC2700 from different companies. I tested them one at a time, and they ran clean. It is possible that there is a conflict, that is why I began looking for replacement memory. At this time, PC2700 is more expensive and less available than equivalent PC3200, too. So, these are the reasons I am checking into the KT3 Ultra 2 support of PC3200 DDR memory. Thanks.

  • MSI KT3 Ultra ARU -- After placing XP 2600+, motherboard dead

    Like the thread title says, my KT3 Ultra ARU board doesn't work anymore  :(  (no video signal, all D-leds red).
    This is what happend, I upgraded my XP 2000+ to 2600+.
    Everything worked like a charm, until I removed the 2000+ CPU and changed it with the 2600+.
    No video signal and all D-Leds are red.
    When I changed it back to the old situation (2000+), the motherboard did the same  :(  
    I changed hardware, but with no results whatsoever(videocard, mem etc.), And the BIOS recovery tool is (like always) not possible, because the system doesn't respond to anything and just hangs at a black screen.
    The BIOS was upgraded to v5.6 (XP 2400+/2600+ Support) before the change. The cooling sits perfectly and the core of the CPUs are good (not broken or anything).
    Are these signs of a dead motherboard?  ;(  

    Quote
    Originally posted by MikNT
    IUpon clearing CMOS I found that I had to leave FASTCOMMAND at Normal since now I operate at 166 and it seems 166 and FAST or ULTRA do not go hand in hand.  I have no idea why.
    Hi! I got the same problem. With BIOS version 5.4 and 5.5 I could choose between normal, fast and ultra. Now with 5.6 it doesn't work at all (also tried with modified bios to have full raid functionality). So if you're running both FSB and memory @166mhz, you can't boot with ultra or fast (I haven't tried ultra, since fast always gives me the best perfomance).
    Ah! And I can choose ultra or fast with FSB @ 133 and Mem @ 166.

  • Kt3 ultra 2 giving ram probs on boot

    Had a MSI kt3 ultra 2 now for about 2 weeks and have a problem that you can work round ,but still damn annoying.Turn PC off ,go to switch it back on ,3 beeps (memory problem). Switch it off at the wall socket for a few seconds,turn it back on,press on button on PC, hooray it works again.Turn it off try to restart it back to square one,gotta switch it off at the wall again.Open up case take out leadtek GF4 4200 and stick in old GF2, all is well it boots up every time.Now I am no expert ,but these problems I and everyone else seems to be getting has to be a bios issue, I just don't believe that a modern PC motherboard chipset can afford to be that fussy.All I really wanna know is when is a bios update due.Thanks
    Athlon 1800xp
    msi KT3 ultra 2
    256mb 2100 ram
    leadtek A250LD GF4 4200 64mb
    P.S by the way tried 3 different sticks of ram as well

    Ok I certaintly would not argue that it couldn't be the power supply,but how can a system be 100% stable when up and running under load with a power supply thats not up to the job.Quite a few people have posted similar problems been out and bought a new power supply ,only to find they still have the same problem.If someone can explain to me why a power supply should "feel better" once i have turned it off at the wall and switched it back on again, i will go out and but one tomorrow.

  • MSI KT3 Ultra 6380E and (RAM)

    Will the KT3 Ultra(6380E) support a 512mb DDR RAM at 400mhz?

    I`m thinking the MB`s and memory are backwards complient, meaning sure 400MHZ memory will run in there, but the MB will not be able to run it @ 400MHz only 333. Right from MSI product info page.
    Main Memory  
        - Supports six memory banks using three 184-pin DDR DIMMs
    - Supports a maximum memory size up to 3GB
    - Supports 2.5V DDR200/266/333 DDR SDRAM DIMM

  • RAM problems with KT3 Ultra 2 causing STOP errors in XP

    I've run the NEC ncramtst program on my PC and its coming up with an error in the extended memory at adddress 1B8EE01C which probably explains the stop errors and problems I've been having in XP...
    I've tried reseating the RAM and tried a different slot but it still returns the same error.
    The PC is only 2 months old and I have only experienced stop errors in the last 2 weeks or so and usually are at random - and occur more often when copying files - or putting load on the PC.. any ideas why the RAM is only now causing errors and what the problem is?
    Are the problems definatly being caused by RAM or could it be the motherboard?
    Thanks in advance
    Ben
    MSI KT3 Ultra 2
    AMD AlthonXP 2400+
    512Mb PC2700 DDR RAM (with errors)
    80Gb Hard drive
    Geforce Ti4400 Graphics card
    Modem
    LAN

    OK I found a few minidumps in the event log
    The computer has rebooted from a bugcheck.  The bugcheck was: 0x10000050 (0xde1d3ee0, 0x00000000, 0x804eef61, 0x00000000)
    Error code 10000050, parameter1 e262ca7a, parameter2 00000001, parameter3 8053cb3e, parameter4 00000001.
    Error code 1000008e, parameter1 c0000005, parameter2 8053cbb1, parameter3 ee5b1a40, parameter4 00000000.
    The computer has rebooted from a bugcheck.  The bugcheck was: 0x10000050 (0xe1fe9a18, 0x00000000, 0x8053cbb1, 0x00000001). A dump was saved in: C:WINDOWSMinidumpMini030703-10.dmp.
    Hope these help

  • RAM or MOBO error? KT3-Ultra

    I have just gotten the Kt3-Ultra and have
    when first turning it on, been greeted with a 3 beep from the speaker.
    The D-Bracket LED's show that the error is a "Onbord memory module may be damaged or not installed correctly"
    The system then hangs.
    What does this mean?
    Is the RAM stuffed (DDR-PC2700)
    or is it the MOBO.
    PLEASE HELP ME!!!! X(

    Quote
    Originally posted by Cmdr_K00n
    I have just gotten the Kt3-Ultra and have
    when first turning it on, been greeted with a 3 beep from the speaker.
    The D-Bracket LED's show that the error is a "Onbord memory module may be damaged or not installed correctly"
    The system then hangs.
    What does this mean?
    Is the RAM stuffed (DDR-PC2700)
    or is it the MOBO.
    PLEASE HELP ME!!!! X(
    I have the same problem, w/ same MOBO.  I have found that if I disconnect the power cord or turn off power strip after turning off computer, the problem is gone temporarily.  It comes back again when I turn off the computer again.  Could there be a BIOS problem, or possibly something to do with the MOBO not resetting correctly??  Please help!!!

  • What RAM works with KT3 Ultra (Orig) ????

    Hey there,
    SORRY BIGDADDY.  Come to find out a new board
    did not fix the prob I am having probs with the OS. Not
    only that but several other programs don't work
    like burning software, drivers, and the new DX won't
    even install right.  I figured NEW CPU...but as you can
    see I need NEW RAM.  So instead of buying PC133 for
    almost the same price I figure get some DDR 2100 for
    about $10-20 more and the KT3 is $10 more.  Do the
    math here and I could substantially increase my comp
    considerably. :D
    Foreveryone out there I need to know what ram works
    with the KT3 Ultra.  I know this board is very picking
    about ram since the AMI bios is the issue.  
    I am looking at these:
    1) Kingston PC2100
    2) Crucial PC2100
    3) Micron PC2100
    Thanks in advance for any replies
    SladeZero980
    I also got a XP 1600 + for $66 from NEWEGG

    OK I found a few minidumps in the event log
    The computer has rebooted from a bugcheck.  The bugcheck was: 0x10000050 (0xde1d3ee0, 0x00000000, 0x804eef61, 0x00000000)
    Error code 10000050, parameter1 e262ca7a, parameter2 00000001, parameter3 8053cb3e, parameter4 00000001.
    Error code 1000008e, parameter1 c0000005, parameter2 8053cbb1, parameter3 ee5b1a40, parameter4 00000000.
    The computer has rebooted from a bugcheck.  The bugcheck was: 0x10000050 (0xe1fe9a18, 0x00000000, 0x8053cbb1, 0x00000001). A dump was saved in: C:WINDOWSMinidumpMini030703-10.dmp.
    Hope these help

  • Kt3 ultra 2 can support fsn 166

    Hi! can I know the KT3 ultra 2 can support AMD Athlon 2700+ (FSB 166 ) or above Or no?
    thanks!!!!!!!!!!!!!!1 ?(  

    http://www.msi.com.tw/program/support/cpu_support/cpu/spt_cpu_detail.php?UID=341%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20&NAME=MS-6380E

  • Ram Problem With KT3 Ultra

    Hi Guys,
    I have posted on here before.
    I have a kt3 ultra mobo.
    The problem i have is when playing games the system locks up and i have to hard restart.
    I have followed advice from this board the the faq ant mobo bios set up which sadly has not solved the problem.
    Very strange but in the pc i have two x 256 meg ddr ram.
    If i take either stick out the pc plays games perfectly. This is frustrating as both sticks work fine on their own but not together.
    ANY IDEAS ? ;(

    Hi,
    Sometimes it happens that sticks just won't work together....
    You might want to swap one of the sticks with a friend to see if the problem is gone...

Maybe you are looking for

  • Error while deleting the T-Code

    i am trying to delete the T-code thru se93 but it gives following error Choose a change request with target system TRQ can u help abhishek suppal

  • Salesorder created using BAPI_SALESORDER_CREATEFROMDAT2 not visible in VBAK

    Hi Experts, I created sales order using BAPI_SALESORDER_CREATEFROMDAT2, further salesorder ID was also indicated after creation. But the same order ID is not visible in SD standard table VBAK. Pls guide me to a valid standard CREATE BAPI for Sales or

  • PC Suite is not restoring messages correctly

    Hello everybody, ive searched couple of times but got nothing really useful, ive managed to create a valid csv file from my previous messages, and when i want to restore messages to phone via pc suite, with import function, everything is fine and mes

  • Comparision Merge clause vs If not exists

    Hi Team, There exits various stored procedures, wherein developer has used if exists then update and if not then inserted records. I would like to know, what is good option, considering with the fact that, stored procedure must be optimized and need

  • Can not restore my Ipad 2

    Hi all Please help. I tried to update my Ipad 2 to IOS 6 , but I dont know what happed , I saw the apple logo and the loading bar moving ,so I left it there . When I got back to it was blank , so I turned it on and the plug into itunes logo appeared