KT3 Ultra 2 funny bios

I have a strange situation here. I have been running a XP1700+ palamino unlocked at 9.5x190 (1810) (max ram timings) with the original bios which was v5.5. I decided to pick up 2400+ so before installing it I flashed the bios to v5.6 which is supposed to support it. It does. Tried overclocking a little with it locked got to 2325@155fsb. Over that unstable.
So I decided to unlock the 2400+. Put back in and it was unlocked, so start going up. 12.5 x160 fsb keeping it around 2000mhz. Totally unstable.Drop fsb to155 and its stable. Try to use the 15 multiplier (stock speed) Boots at 933(7x). Try 14 mult. @666(5x) useless multipliers. Now it seems I'm being limited by the fsb, strange because 1700 would run @190fsb( everything the same except CPU and Bios).
I figured I must have got a bad Cpu.So I pull it out to see if something else may have gone bad, and put 1700 back in. Suprise!! max stable fsb 155. .
After Trying slow timings in bios and everything ,still no go. SO I flashed back to bios v5.5. Reboot we're up to 173fsb .Ran tests over and over.Stable.. Better but what happened to 190!!!
So now I put the 2400 back in unlocked and works fine up to 173fsb BUT I still have a max mult of 12.5 and max fsb 173 .
Is the bios these boards ship with different than the ones they have posted on their site?
If anyone has any info, it would be appreciated.
Phil
System
KT3 Ultra 2
Xp2400+
1 X 512 winbond
Ati Radeon 8500
Live! Value
Intel 10/100 pro
Plex 16/10/40
Lite On 163
cmd raid controller
2xWD400bb
1XWD800bb
Vapochill
Vantec Stealth 420w PSU
Logitech Z-560

Thanks for the reply Maesus
I have been clearing CMOS each time. I understand that It would seem to be hardware but not sure why I can once again go higher when I flash back to older bios (not as high as original but higher than v5.6) Also with the 1700 the bios was the only change.
The other thing with the multipliers of 14 and 15 not giving the correct result also bothers me. I know it can do a 15x because it does with cpu locked but when unlocked no go. Is this a limit of the KT333 the KT3 Ultra 2 or a bug in the Bios.
One last thing there is an option 12.5/13 but as far as I can tell choosing it only give 12.5 .Is there some way to get 13x ?
Phil

Similar Messages

KT3 Ultra (2) Bios version 5.7 released

MSI has now released bios version 5.7 for the KT3 Ultra (ARU) and KT3 Ultra2. Fixes posted are:-
Support AMD Barton XP3000+ (FSB333) CPU (For KT3 Ultra2 only)
Add CPU Halt Command Detection in the Bios Setup
Fixed ATI 8500 AGP Card cannot be used
The new bios can be downloaded here:-
KT3 Ultra (ARU)
Link
KT3 Ultra2
Link

Juras. This thread may help answer your question Link

KT3 ULTRA-2 BIOS 5.5 OR 5.6 ?HI

Hi. I have a kt3 ultra-2 that had a 2000+ cpu.
I upgraded the cpu to a 2600+ that runs at 333. So i set the fsb to 166. It works just fine. my question is.
My bios is 5.5 and 5.6 says it supports the 2600+.
Do i need the 5.6 bios? Is ther new settings in it for a 2600+. And does live update 2 really work right with ntfs and xp. thank you for the help )

Hi,
No, you can stay with 5.5 if you like....
5.6 won't add settings, if 5.5 is running fine, leave it alone..
Yes, LiveUpdate works with XP and NTFS.

KT3 Ultra 2 - Bios V5.7 - Problem

Hello,
I don't know if anyone else has tried updating the KT3 Ultra 2 to the new V5.7 BIOS ?
I tried and got load of error messages on the screen, Chipset isn't support etc ROM Size Unknown ....
I have V5.6 on right now.
I have tried Live Update, it doesn't show new bios and also tried another floppy with files on and also downloaded the file again.
No win !

I did not have that particular problem but I found others
I was able to load new 5.7 bios but after I did it took board about 2 minutes to boot.
The part where the XP logo screen is supposed to come up took about 2 minutes. There is no HD (light) activity and then all of a sudden you hear harddrive and XP logo screen comes up and it boots fine.
The same situation arose with Bios 5.6 but I was able to fix that by changing MPS table from Default 1.4 to 1.1. The XP screen would take about 2 minutes to boot so I tried changing settings in bios and finally came to the MPS entry and changed it to 1.1 and the board booted fine. It took about 3-5 sec for the XP logo scrreen to pop up after the last bios screen that would show all the Devices, IRQ's ect...
Changing the MPS to 1.1 in the 5.7 bios did not fix the long boot problem like it did in 5.6.
I can live with the 5.6 bios but the CPU halt command in the 5.7 bios drops temps about 20 degrees F and that is great. I hope this problem can be fixed in 5.7 so I can utilize the CPU Halt command.
My Second Rig: Backup
AMD Athlon XP 2200 (266 fsb)
MSI KT3 Ultra 2
XP Professional SP-1
512mb Crucial PC2700
3 Western Digital HD (2) 80Gb and (1) 20Gb
Enermax EG365AX-VE powersupply
Hercules Gforce 2 GTS/Pro 64mb
Waveterminal 192L sound card
Promise Ultra 133 TX2 card
Intel Pro/1000 MT desktop adapter
Plextor 24x10x32 CDRW
Toshiba DVD
Coolermaster ATC-201 Case
CoolerMaster HHC-001 Heatpipe HS

MSI KT3 Ultra ARU BIOS FLASH

currently trying to flash my bios upto the current release to attempt to fix a problem that seems i am not the only one to have and have tried every other solution provided.
Now i have flashed many a bios before but never this one....my current version is 5.1 and i am trying to install 5.7. Here's the problem.....when i load dos from a win98se startup disk i goto the c: drive and then run a "dir" to get the list......however instead i get a "file not found" for the whole drive (i am guessing do to it not being able to read a FAT32 partition/drive). so i am able to copy the bios flash files to a ramdrive that the startup disk creates on boot but i am reluctant to install from there as i don't want to fuxor something up by doing so. i would just install them from a floppy but the instructions that come with the flash file say specifically not to install from a floppy (though no reason for this is given).
My questions are these:
1. can i copy the files to the ramdrive and install the bios flash from there without having any problems that anybody knows of?
2. why can't i just install the flash from floppy? i've never run into this on any other boards is this an MSI thing
3. is there a place that i can get a bootdisk online that will allow me to read the fat32 disk so that i don't have to worry about any of the above solutions that i have come up with?
any help with this stuff will be greatly appreciated
tia
Aaron

nevermind i figured it out thanks anyway

KT3 Ultra + v5.7 BIOS -- weird behaviour

I have KT3 Ultra with newly flashed 5.7 BIOS + XP2100, 512 333DDR, Club3D 9700np, WindowsXP.
I had some start-up troubles after installing 9700np (8 beeps and no signal), which forced me to reset the system every time after power up to load windowsXP. So, I decided to flash the BIOS. Now, system boots up with no problems, but I've encountered a new problem.
Pressing ctrl+alt+del doesn't bring up the TASK MANAGER. All I get is the CPU USAGE window. Thus, processes, applications etc., those are gone. This means, basically, that I can't shut down programs that are not responding (not that I need to do that very often, but still...). Right clicking on the task bar and selecting TM shows me the same CPU USAGE window.
In addition, IE's pop-up windows that launch external programs (like some sites offering mp3 ring tones that I play with Winamp) cause IE to crash. Never happened before.
All this happened right after I flashed the BIOS. Any ideas?!?! Should I go back to 5.5 that I had before?
Thanks,
Thomas

This is pobubly off topic, but since the title is KT3 Ultra and Bios 5.7 I decided to ask here so as not to create a duplicate thread.
I to flashed my Bios to 5.7, but my problem is as follows.
After flash rebooted my computer as instructed, entered bios and verified all my configurations. Rebooted again. Windows came up fine but all text was garbled and unreadable. Reflashed 5.7 (thinking it didn't take). Again same problems. Had to flash back to 5.6 inorder to straighten out.
Bas any ideas?
Thomstucks:: Sorry to hear about your problem, and for jumping in on your thread. Have you tried 5.6?

MSI KT3 Ultra-ARU

Can anyway say to me the PCI/AGP dividers of MSI Kt3 ULTRA -ARU?
Thanx in advance

Quote
Originally posted by 343
you got the speeds wrong still.
The agp 1x, 2x, 4x, and on other new mobos 8x, have nothing to do with the speed at which it operates. It has something to do with the transfer and how much more bandwidth there is between the agp card and the system bus.
The 1/4 dividers has:
PCI = 1/4*133 = 33mhz
AGP = 2/4*133 = 66mhz
The 1/5 dividers has:
PCI = 1/5*166 = 33mhz
AGP = 2/5*166 = 66mhz
The futuristic 1/6 dividers will have:
PCI = 1/6*200 = 33mhz
AGP = 2/6*200 = 66mhz
Your equation "...and the AGP card of 4X = 4(FSB/5)" would yield a result of 4(133/5) = 106mhz for the agp so it is way out of spec.
Hey man, I've unlockes my athlon xp 1900+, changed multiplier to 10x, fsb to 166 and sisoft sandra 2002 sp1 said that the pci was running at 42 mhz and the agp at 84. MSI KT3 Ultra-ARU, bios 5.5
Also, I can't run with 12.5/13x, it uses 12 instead.
Can you help me?

KT3 Ultra-2, Blank Screen then Freeze?!

Ok, this happend to me last night, and am clueless
I was playing CS for 1 hr, then suddenly screen went black, no sound, no response. To me my PC frooze, then i hit the reset button. But then i got a CMOS Invalid Config Error, all the info was cleared?
So i re-entered the BIOS SEtup values again, then while checking some info on a webpage, BANG, it happened again, Blank screen, etc etc etc...What is wrong?
I have DEER 350 Watts psu, 256 Kingston DDR266 CAS2 Module, XP1600+ (not oced) and normal BIOS Defaults (after what happened) and an ATI Radeon 8500LE, and KT3 Ultra-2 Bios v5.6, Windows XP SP1
Thanks in advance ;(

Hi,
First check your CPU-cooler, if it's mounted wrong the board will shutdown to prevent damage to the CPU....
Check if the JBAT jumper is set to position 1-2 to safe the data....
Please read the trouble shooting guide entirely....it might just solve your problem...

MSI KT3 Ultra ARU 5.7 BIOS and SoudBlaster Cards - Audigy

I have flashed my BIOS to 5.7 Version and my sound card start to make a lot of noise (crackling) when play AC3 or DVD. If you dont want to use the new AMD CPU 333 FSB you dont need to flash the BIOS - I have Flashed to 5.6 again but, if you want to use a 333 FSB CPU you can flash the BIOS to version 5.7 and if have sound problems use the PCI latency patch for VIA chipsets.
VIA chipset MotherBoard owners who have through all of the above and still have sound problems with their Soundblaster cards, might want to look into the PCI latency patch for VIA chipsets - get it here:
http://www.georgebreese.com/net/software/
(scroll down the page there just a little to get to it).
There's also a similar page about resolving sound problems on Via chipset based computers here:
http://www.deinmeister.de/mvp3_zlt_e.htm
I hope this post help somebody
Mário Silva from Beja - Portugal
My System:
MSI KT3 Ultra ARU
Athlon 2400+
512 Kingston PC2700 DDR SDRAM
MSI Geforce4 Ti 4200
SoundBlaster Audigy
Windows xp Pro SP1
400W PSU
Creative Drx3
Pinnacle PCTV pro
HDD Maxtor 80 GB UDMA 133
DVD Pioneer slot in
RW Samsung 48x16x48
Creative WebCam Go
UPS 500 VA
Monitor Sony 19" E400E

Since my chip is an unlocked, I cannot easily run it at the default, but I can underclock it. At 100x6.0=600mhz, USB does not work, as well as 100x12.5. Same with 133x6.0 and 133x12.5. It appears to make no difference underclocking or overclocking.
I downloaded the right BIOS listed on MSI's KT3 Ultra-ARU page. I don't think the BIOSes are different anyway, since the same files, changelog, and etc are also listed for the Ultra-2 board.
A thing to note, that this is the onboard VIA-controller USB ports doing this. My Ultra-ARU's NEC-controller USB 2.0 ports work fine in both Win2k and Linux if I hook my mouse and keyboard up in those. This is not an ideal solution for me though.

Max hard drive size on a KT3 Ultra ?? bios is 5/24/02

MSI MS-6300-Series MS-6380E (KT3 Ultra-ARU)
I have a Maxtor 40gb ata 100 hd,and want to grab a bigger drive.I am running Win 2K
If I do need to flash.
What bios do I need to flash to,and what is the max size hard drive I can use with this ancient motherboard ? thanks in advance.
Also have a 32x cd rom LG
and 2 128mb sticks of ddr
Athlon XP 1800
EDIT: NM all,I found it can up to at least 250Gb hard drives on ATA133

MSI MS-6300-Series MS-6380E (KT3 Ultra-ARU)
I have a Maxtor 40gb ata 100 hd,and want to grab a bigger drive.I am running Win 2K
If I do need to flash.
What bios do I need to flash to,and what is the max size hard drive I can use with this ancient motherboard ? thanks in advance.
Also have a 32x cd rom LG
and 2 128mb sticks of ddr
Athlon XP 1800
EDIT: NM all,I found it can up to at least 250Gb hard drives on ATA133

KT3 Ultra MS-6380E whit bios 5.0

My KT3 Ultra MS-6380E whit bios 5.0 don't recognize fsb of athlon xp 1800+ .
Mainboard set fsb at 100Mhz if i set manually at 133 the system don't boot.
I go at bios update in msi site and ALL bios tool for upgrade are a AMI BIOS

I am running a XP 1900+, I wouldn't run with my old 250W PSU, bought an ALLIED ATX 350W, and runs like a charm. Only $30. Easy Fix

Big problem with KT3 Ultra (ms-6380e v1.0) after flashing the BIOS (de

Hello out there.
I have a real complicated matter with my Kt3 Ultra board.
Used to work fine, but after I flashed it with the latest BIOS (5.7), the board has this strange behaviour: when I clear the CMOS, the board boots up, when I change & save the settings, the board does not "come to life"(black screen & beeper silent).
It has also this weird problem: it shows garbage charaters on the voltage setting of the CPU. Instead of voltages (i.e. 1.750 etc. etc.) I have only "scrambled" strings.
I had MANY difficulties in upgrading the BIOS because the AMI-flashing utility kept telling me "bios protection enabled) (but there was NO bios-protect setting in the previous bios - I checked a zillion times)...but after trying with different revisions finally I made it.
I already tried everything (re-flashed older bios-es etc. etc.)and I'm starting to feel beat ... if you have any advice, please le me know.
It would be really SAD to put this great board in the garbage-dump....
Bye,
Wyk'03

im having problems with this board as well,
i had no problems with the flash,
i did this...
boot to win me floppy,
copy the flash files to ramdrive, flashed to latest bios..
now windows hangs when i have my ac97 audio enabled in bios...
I WANT MY AC97!
hmmm can you get to a dos prompt from a boot disk?
try re-flashing with 1.0 again and then disable the cmos virus protection thingy, and yes it was there it was in the 1.0 bios on the main screen.

KT3-Ultra 5.7 BIOS.....

Hi,
The KT3-Ultra (-ARU) 5.7 BIOS will be released official this week...
Don't expect much changes over the last BIOS as there are very little.
As these are the only improvements:
Fixed AMD 2600+(266MHz FSB) CPU shown incorrectly
Fixed ATi8500 AGP card cannot be used

Quote
Originally posted by Bas
Hi,
That there isn't official support doesn't mean it won't work on the board....
As I heard from several people that the TBred-333 CPU's do work, even when they are not supported....
We have to wait until somebody tries it :D
Hi,
I know, it's only a bios trouble, infact on the MoBo page (at CPU support section) are tested processors till +2800/333mhz without problems, and my T-Bred goes easy at 166mhz. Barton have only 256k plus L2 than T-Bred...but why MSI dosen't make a bios with the official support to 333mhz? The KT3Ultra2 was reported officially (in old news from MSI) with 333mhz support. I'm very disappointed about this... :(

KT3 Ultra BIOS problem + question

Hi
after switchin on the CPU Halt command detection. My PC beeps 3 times after shutting down. D-LED says memory problem. When I turn off the PSU and after a while turn it on, everything is OK and PC boots normally. Does anyone know the reason of the beeping??
Question: has somebody tried (somebody very rich to afford buying Barton) Barton (or T-Bred FSB333) processor on KT3 Ultra??
thx a lot )

Hi,
Switching on CPU HALT Command will make your system unstable. That's the message of the beeps.
You should be able to improve this by using a better PSU. Otherwise, there is no reason of using CPU HALT command as there are many software CPU Coolers you can get.

My KT3 Ultra Experience (from the nightmare to a running well system)

Well First...
I don't speak a well english, maybe because still think in spanish, so maybe find many gramatical errors.
the very very begin
The history begins with a terrible electric shock in my house, i got a Athlon XP 1700+ with a cheap PC Chips Board (810)..yeah the all in one board (video, modem, ethernet, sound) build my first system with a mixture of expectatives and dreams with my first AMD athlon XP , the system running well, before got the "great idea" to plug a Zoltrix Genie TV card for record South Park, everything is OK, so, i think that i abuse the luck, and a rainy night, i surf the net ( a XXX one... ATK... never forget that site after this) a electric shock enter trought the tv cable searching ground, someone that got this experience maybe feels a demon in a box, a white light come out from the back of the system and hit the isolated regulator ( with the sparks and all the stuff ) the light goes out and a tasty barbecue smell fill completly the room.
ohhh...
the list of cooking components:
   Athlon XP 1700+
   PC Chips 810 (a/v/r/s)
   Maxtor HDD 40GB
   Zoltrix Genie TV
   Mouse (generic)
   Keyboard (generic)
   Microsoft sidewinder gamepad
The miracle pieces:
   256MB DIMM sticks from crucial (PC 100) two of them
   External CD Burner HP CD-Writer 8230e (USB)
   Philips Monitor 17'
i learn to never watch a porno site in a rainy night... it's really bad for your system
build another system "da plan!"
in a trip to Bogotá i search in the computer mall called UNILAGO, the new system board, someone callit MOBO, my idea are this:
A Boxed Board. Candidates like ASUS , Gygabyte, MSI, with the VIA 333 chip are required.
we search in all the place, asus show its A7V333 model, but its too expensive in the price that this guy offered (maybe think that i don't search the pricewatch.com page before go to the mall... je je) in a place some guy show me a very nice box... i think the first impression counts, its the kt3 ultra board in her shiny box, next tactic ask for minimun price (...no minimun price got this board...) so i pay 360 thousand pesos for it.
wen come back to Cali ( the place i live) and after got some pesos in my bag i go to the computer mall in Cali called La passarella (remember the argentinian soccer player?) for buy the components.....
the list is this:
   Athlon XP 1800+ BOXED (got the original AMD heatsink)
   DDR RAM PC2100 256 MB
   Genius Netscroll Optic
   Genius Keyboard
   CD-Rom LG 52 X
   Case with a 300W ATX Power Supply
   Realtek Ethernet Card (Encore)
   AGP Video card with the SIS chip 315 128MB of ram
   Genius Maxfire USB (i buyit for the cheap price and anyway i don't play too much in a computer so i dont need a Nvidia Ti thing or a gamepad expensive)
wen go to the house, plug all the stuff and the process it's fine, no complicate things occur, i do two modifications first
1)to the AMD heatsink, the clip come in the other side, so i need to unplug the Power ATX supply for attach it and don't want to do the same thing every time that retire the heatsink, i disarm the heatsink and turn the clip to the other side, no problems with this mod...
2)i don't use floppy disks... I HATE IT so the place of the floppy converts in the place for the D-Bracket with all the lights and two USB... nice because i perfored the case in the right way and the usb and the lights come in the front of the case...it's a easy mod...
all the things come well so turn it ON...
KT3 Ultra first Round!
well i don' pay much attention in the first time that power on the system and hit the del key.... nothing happens and a letters of searching array and scanning devices show... after this process the amibios screen shows (the blue one, and still today don't find the option for change the color scheme like te PC Chips amibios options got) in this point i know that the rule "search the instruction booklet" it's totally necessary for many options the options that i disable and some that enable are this:
    in integrated peripherals disable the ata raid option (remember the scan devices screen?) i plug a maxtor ATA 100 hard drive to the ide cable because don't know if this hard disk works with the Raid Option maybe not because is ata 100.. so disable the option
    in power management options i activate the CPU critical temperature to 70°C
    in advanced bios settings i enable the MSI link to the future screen... nice, SMART for HDD enable. In the boot secuence put first CD-rom and later HDD
    in standard CMOS settings put the hour...(uh!), and obvious disable the nasty floppy drive (BOOT CDS REPLACE THE NEED OF FLOPPY DRIVES...)
    in PC health disable the intrussion option, because i don't have the switch for the case...
    in frecuency and voltage i find the FSB in 100Mhz but i don't change anything in this point...
after this tiny modification, i save the changes and restart....
the system boot with a CD he he... with a image of the win98 boot disk, so i formated and fdisk the drive... tooooo fast in this point.
after partition the HDD in 5 pieces and formating every partition, i reboot the computer for installing Win98...
the installation goes normal, and install all the MSI software (only for know what apps are appreciable por me) i don't have any problems, install all the drivers for every single hardware piece and the system works well... so testing es the next point.
KT3 Ultra first test after the installation
well i feel that my job are easyly...(ji ji) and all the process go OK so testing my new machine gotme like a child.
i run the test of SiS for the AGP card ( 3D thrill ) the demo of the card got a cosmic scene, comes very fast, i try to watch if someone piloting the space ship, and maybe see something
the sound are good for the include sound chip in the board, put and test all the effects and test...ok ok... nice.
microsoft direct X got some testings so i run it too ... write in run command "dxdiag" and ready for the tests, in this point i feel free to install a copy of "formula 1 2002" in the machine some guy borrowme a copy, wen i try to install got a n error.... (the first one) and the game don't install ... i reject the installation and try another game, in this point i search the Athlon XP Oem.bmp file for branding my new system... je je, and hit the window key and pause and i find that my processor runs in 1.1 Mhz... (what!!!) if this CPU is a 1800 and this speed maybe is wrong....so i read the boocklet and find in the FSB option the way for put the CPU in his real Mhz...(1.53) in this point begins the troubles...
KT3 Ultra damage my CPU??????!!!!!
Wen enter to the bios i got direct for the FSB option and put it to 133Mhz maybe this thing it's easyly too, i think, i made and save the changes... and.....
A BLACK SCREEN COMES AND I SEE THE FOUR LEDS IN RED!!!!
AHHHH!, i thinks that this processor pases to a better life after this point, with shaking hands read again the boocklet and find the interpretation for the 4 red leds signal, damage or bad installed processor.
oh, so what i do...?
i continue reading for a little FAQ in the boocklet, and nothing, only a glossary, i call a friend to helpme... ( the true geek one) the guy tell me to reset the bios with the jumper... so, i don't loose anything with this and do it...
wen the computer reboots the signals come to life... (ufff!) and the scanning device creen shows again... so i need to save again my settings.
i do all the things and save, the system turns on and windows 98 load normal again... i try to fix the FSB thing in other time i think, and continue intalling some programs.
In my CDs find a copy of formula 1 2001 no de 2002 version, because this version i installed in my other fried system i installed in mine for show and prove the 3d card...
the installation works fine and terminate ok, wen i hit the icon to play, the 3d settings window appears i select some options 800x600 32bit color and press test, a blank screen comes with some little caracters, in some point wen the test come back my system frozes and nothing happens... OHHHHHHH! what happens?.... i think, i decided to check the temperature values because in this point think that my installation fails in the put heatsink process.
i load PC alert and find CPU temperature in 78°C... oh, it's too high i think so shutdown the system and check the heatsink for anything that miss in the first time.
i put again the heatsink an log to the bios for check the values....
this is the values of PChealth option in bios:
   Cpu temp : 71°C and stable in this value...it's high too
   System Temp : 38°C ...high too
   VCore      1.744V
   +5.0V       5.038V
   +12V      11.923V
   -12V      -11.497
   -5V         -5.026V
   Batt      3.24V
   +5VSB      4.969
some ideas come to my mind and try to think if some options of the bios, the best performance option it's a good point to start i think so i select and save the changes...
oh, oh, the black screen comes again.... buuuuuu! and the four red leds too....buuuu!
mmmm, ....what i do?, what i do?....i reset again the bios, for the options and try to boot the machine again... maybe leave the system in the first point i think but nothing prepare me for the many "chorro" of errors thath follow after this point....
If i can roll back the time....
i think to be superman and fly in a oposite earth direction for roll back the time... (luisa!)
the system begins a non stop errors secuence sometimes the four leds are red, sometimes tree leds red an the top right led green, in the book says this signal is for damage DDR ram...
wen windows 98 loads the system frozes in some points, and wen enter and run some test the system frozes too...
i reset the bios to the original form an try to leave the house excactly wen enter the first time... i save it and the errors continues...
with NO hope of correct by myself the issues i turn on my old K6II system and find the MSI forum that got some mysql errors
in the forum find the Power unit suplly issues, i got the ATX box and 300W maybe it's too low i think after MANY post with same errors like me, i think to made a program plan for recover the stability and my ideas come in the next point.
now need another message to continue....

Return the system to the "normal" or less stability
In the forum (thanks for the people thath participate) some people says issues of frozen systems because cheap ATX power supply, some other got problems with the heatsink, i think that a mixture of those issues gotme like mad and try to figure out the quality of a atx power supply that changes the performance after a bios setup... ( it's a very cheap ATX power supply, i think) the Power unit now don't support the energy, and power needs of the system in some cases wen i run the 3d accelerated test the system frozes wen i hit "test".
return today to the computer mall passarella, and buy this items:
   Vulcano 7 (it's a building no, it's a airplane no,... it's vulcano 7 with speed sensor incorporated, much bigger than a building and more CFM than any airplane make!)
   ATX power supply 400W for kicks power requeriments and maybe extract energy enough for a reading lamp...
   wen come back to the house i install the new parts, the vulcano 7 needs the same mod than the other AMD one, or maybe MSI put the sockect A protect clip layer in the wrong site, maybe the board fit well in a ATX-XL case for no uninstall the power unit to put the heatsink... anyway need to uninstallit but this issue it's funny.
wen everiting it's ok i turn on the system...
KT3 Ultra Runs smooth... FINALLY
i know thath every body needs to listen a couple of help tips, in this point i think that logged to the forum are the best idea that i got, many people got the same problems and if you don't ask or search you think thath the MSI board it's a terrible board, and this no true, and because it's red too.
the system loads normal and i think to go up the FSB to the NORMAL 133 value for this athlon XP 1800+ i change the values, save and reboot the first thing that i find are the bios recognize the Amd Athlon XP 1800+ in the first black screen ( wen disables da logo) later, web hit windows key+ pause the window says Athlon XP 1800+, in the fuzzy logic app i find the values of 1523 Mhz and the temperature don't rises 50°C it's now OK, better than the cooking eggs thing that got before the changes.
now i need to give some thanks..
Thanks
to all the people in the forum, i don't write a nice english but i know read and it's enough for take a easy living style with this machines...
MSI people thanks
for the people in the mall, they don't know much the Power unit issues of this board it's a bit more exigent than others in his point.
to my dog that share my angry in the late night, it's a good one that dont' sleep well wen i work in the night..
so to all the people thanks for made this posible, maybe this long post with less technical things works for put your boards well.
Victor Hugo Hernández
Cali - Colombia

KT3 Ultra 2 funny bios

Similar Messages

Maybe you are looking for