KT3 Ultra BIOS problem + question

Hi
after switchin on the CPU Halt command detection. My PC beeps 3 times after shutting down. D-LED says memory problem. When I turn off the PSU and after a while turn it on, everything is OK and PC boots normally. Does anyone know the reason of the beeping??
Question: has somebody tried (somebody very rich to afford buying Barton) Barton (or T-Bred FSB333) processor on KT3 Ultra??
thx a lot )

Hi,
Switching on CPU HALT Command will make your system unstable. That's the message of the beeps.
You should be able to improve this by using a better PSU. Otherwise, there is no reason of using CPU HALT command as there are many software CPU Coolers you can get.

Similar Messages

KT3 Ultra cdrom problem

Ive been having some problems getting my cdroms, or any cdroms for that matter to work correctly on my KT3 Ultra (MS-6380E). The bios recognizes exactly what my drives are boots, and both windows and dos recognize that they exist but 99% of the time they will not read any cd's. They have this problem no matter which IDE channel i plug them into, but my hard drives have no problems at all in either channel. I've tried changing the IDE cable, plugging in only one drive at a time, messing with the master/slave settings, resetting my bios, updating my bios, drop kicking my computer and lots of other stuff.
Im almost certain that the problem is not with my cdroms because i dont see how they would both break at the exact same time and a third cdrom i tried from another computer would have the same problem. Im also fairly certain it is not a software problem because i have reformated, repartitioned, cleaned my MBR and virus scanned 900 times. I also have the same problem even with my hard drives unplugged completely and booting off a boot disk.
I dont see anything else that could be causing the problem besides perhaps a faulty motherboard but i cant find anyone that even has the slightest clue what is wrong, or any reference to any similar problems anywhere online. Does this sound like a something a motherboard problem could be causing? Here are my system specs:
MSI KT3 Ultra (MS-6380E)
Athlon XP 2000+
256 mb crucial pc2100 DDR SDRAM
GeForce3 ti200 64mb
SB Live! Value
Netgear NIC
40 GB samsung hdd
60 GB seagate hdd
the cd roms currently in my computer are a RICOH 4x4x8 burner and a generic 56x. Ive asked a ton of people and have been trying to fix this problem myself for months. Any suggestions would really be appreciated. Thanks.

80 wire ide blue end to board
tried them 1x 1 as some drives just will not pair up
does bios see them right,is that ide on auto
try as this guide as well
http://www.amdforums.com/showindex.php?s=&threadid=124482

Kt3-ultra big problem

i have just bought a kt3 mobo and am having some serious problems getting it to work properly.
the 1st problem is my cd burner or dvd will not install anything. if it is allowed to autorun it will stop giving various errors. and if i install by clicking setup.exe the same happens. also it sometimes restarts the computer.
i have plugged in an old cdrom which seems to work fine.
the 2nd problem is my broadband connection. i am using an alcatel usb modem and i cannot get it to connect to the computer.
i install all the drivers first then plug it in, it then says it found the modem and is installing it and completes with your hardware is now installed.
all that happens now is the lights on the modem looks like its going to work but then goes off then back on again.
this goes on for as long as its connected.
i am using :
windows xp
amd 1200 thunderbird
256 ram
400 watt power supply
kt3 ultra
ibm 80 g.b deskstar
i have also been swopping componants with my other computer and i know everything is working fine.
i hope someone can help because i have been trying for 10 days now to get everything running and i am pulling my hair out.
many thanks

Hi i have been having problems with my adsl cuting off and the modem lights paling up a reset will usually work to get it connected again. I am using an external sagem adsl modem and the power draw for it is 400ma, most other usb devices only draw between 2 - 10ma. This can cause the computer to hang and the modem to disconnect. To fix this buy a self powered usb hub that is capable of more than 500ma per port this will eliminate the problem. As for other power issues i have 3 cdroms 2 of which are writers i have a gforce 4 vido card network card and have had no advers affects from power other than the USB problem hope this helps
AMD 1600 (1400)
MSI 6380E
GForce 4 mx 440 128
2 X 256 pc2100
sony rewrite 52 speed cd writer
freecom 4X dvd +/- rewriter
3com 100mb network card
4 usb 2.0 ports
4 usb 1.0 ports
Sagem adsl usb modem
Creative labs soundblaster live soundcard

[VIA] KT3 Ultra 2 Problem

"My KT3Ultra2 won't start ... there's no beep or picture shown on my screen.
The D-Bracket LEDs shows : "Initializing Hard Drive Controller" (two red on the up side, and two green on the down side).
i removed the HDD and it's worked on my other system.
can anyone advice me what should i do ??
Thank you so much.

Quote from: Grayone on 09-January-06, 15:26:35
Sorry, I missed the first line about it not posting. Sleepy, I guess.
Swapping parts like the video card between the two systems will eliminate that possibility since it could be power supply or cpu or video card that stops the boot process before it can initialize the hard drive controller.
Please furnish us more information about what parts are in the system? Create a profile containing info similar to I have in mine. The info will make troubleshooting much easier.
hi mate, thanks for the fast replies.
i had done all the sweaping of parts from one system to another. as for the power supply is a new one.
my system is using MSI KT3 Ultra 2 (MS-6380) running on CPU AMD 2100+
Ram is Kingston PC2700 333Mhz 512MB.
A Maxtor HDD 40Gig.
A creative Sound Card.
lastly a Benq CDRW.

KT3 ULTRA 2 PROBLEMS

GOD! where do i start,........just bought a system based around a KT3. ive had it about 4 weeks, running fine.then gradually things have started to go wrong.....reboots,freezes,cd access crashes,blue screens of every code under the sun! so i thought no bother ill reinstall......bad Move. ME crashes half a dozen times durin install and i end up with unstable desktop. so i tryed XP...not a chance! ive played with the bios settings for hours on end to no avail,so now im thinking whats the score ere like?some one just got to help me,before the shopkeeper gets it over his head!
So now i deffo think its hardware...the question is what! writing this on mangled explorer,nodrivers installed,sick as a parrot XP2000+ 500meg 80gig 7200 350wpower

+5v +3.3v
25a 15a
coolers sat right way round,fuzzy,s always gave me 49c average cpu ,although i tend to get abetter install from cold boot....maybe the shop used cack paste,i dunno....ive been thinking it was a heat problem, my system gets worse as it goes along.
its still under warranty so ididnt want to start leaving nasty evidence of my intrusion(scrape scrape)just needed some ammo to take to the shop.i dont really want to get into that'weve fixed it routine'....or 'nowt wrong with that mate' etc etc shops tend to give you.
any more pointers would be welcome ........ ;( thanks

KT3 Ultra memory problem

my problem started after i ordered 2 crucial pc2700 512mb for my kt2 ultra board. after removing my old 256mb pc2700 kingston stick form the 1st slot, i put the crucial and slot 0 and 1 and booted. my comp started beeping and the flshing thing on the back indicate a memory error. so i turn it off and move the sticks to 0 and 2 booted again and now boots up fine. going into windows to check my 1gb memory and windows only display 512mb 1/2 of wut i have. so move the stick to 1 and 2 and still 512mb not 1gb. clear cmos, flah bios, unplugg power supply to mobo still the same problem. i remove all the memory and thought maybe ill use 768mb for now put the 256mb on slot 2 and 512 on slot 1 and windows registered it at 256mb not 768.
can somone plase help me??
my power supply specs if this helps
+3.3v:28A
+5:40A
+12v:18A

hi
sounds like a mobo where the memory slots is bad.
happens way to often.
but i suggest you wait and se what other people in here have to say so you dont run away and rma the board incase its something i dont know how to fix.
my knowledge is mainly on the k7n2 board.
i im downloading the manual and will check it to se if i can come up with something else.
16 minutes to go and i have 1mb cable internet.
talk about slow connection.
bye

Kt3 Ultra reboot problem continued

my old post (last weekish)
Above is my old post. Someone at the end of that thread told me to write down my blue screen stuff before i reboot...so here it is:
I get one of these two usually
Up near the top it says this
"This problem is probably an issue with win32k.sys file
PAGEFAULT_IN_NON_PAGED_AREA_
(further down)STOP:
Crazy stuff 0x00000af0f00a00 etc."
OR
"DRIVER_IRQL_NOT_LESS_OR_EQUAL
(further down) *** crazy stuff 0x0x000300b0v00 etc.
***classpnp.sys"
sometimes it won't say eigther near the top....but almost always that's what it says. I just ordered a new Asus A7V333 for 140$ arrg...so I'll probably keep that if I can't fix this problem pretty soon.

It seems we have the same problem taraturg. I saw your messages last week, and I have the same bluescreens.
They are like this:
STOP: 0x00000050
PAGE_FAULT_IN_NONPAGED_AREA
..........ntoskrnl.exe.....
...beginning dump of physical memory....
STOP: 0x000000D1
DRIVER_IRQL_NOT_LESS_OR_EQUAL
........v124nt.sys......
.......dump of physical memory.......
I have also run the memtest86 and after an hour or so there was no errors. My CPU temp are stable about 52-54 celcius. I run win2k with the latest updates, the latest bios(v5.6), the latest drivers. Everything you can get(!) And still this ( ) isn't working. What's wrong?

KT3 Ultra-sound problem

Hey, all.
I recently had to reinstall Windows on a custom built system-everything came back OK excpet for the onboard sound. According to the device manager, these were several driver conflictions (including MPU-401), which I fixed with the latest drivers I could find. However, the sound still isn't working.
For some reason, every now and then on startup, the system detects "new" hardware, namely:
VIA standard PCI to ISA bridge
PCI host bridge
VIA standard CPU to PCI bridge
for all of these, the only driver it can find is Viamech.inf in C:\system.
I tried buying a new sound card (Hercules Muse LT) and no joy with that, either, so I'm assuming it's a problem witha driver somewhere along the line.
Any ideas?

Hey, guys-thanks for all your help-I finally got the sodding thing working!
I bit the bullet and reinstalled Windows (with the new sound card installed, hoping my system would use that as default over the onboard chip). First thing I did was run the latest 4-in-1....and got the exact same error messages with the drivers!
You can imagine what I was like ( ), and I started clicking angrily through the browse button, getting increasingly annoyed at the "Dunk!" error sounds coming from my PC, so I turned the sound volume down.
Hang on....error sounds?!!?!?
Hooray!

KT3 Ultra video problem

After working fine for several months I've started having issues with my video card. Running Win XP, I'll have a video lockup, which Windoze occasionally recovers from saying there was a device failure, or a reboot indicating a possible hardware failure on reboot. The error message always blames the video driver. I've tried 2 different cards -- an MSI G4 4400 and an ATI Radeon 7500 I bought just to test, with the same results.
The box has an XP 1800, it was overclocked just a wee bit to 137 FSB. I've taken it down just now to see if that could be the problem, but I doubt it somehow.
I'm wondering if it might be a short of some kind. The only brass stands I'm using match up fine with the screw holes in the motherboard, but I'm not using any insulating washers as the case instructions didn't call for any. I'm assuming the screw holes on the motherboard are insulated, but the appear to be cased in metal. Can anyone tell me if this or something else may be the problem?

Tragically I've still had no luck. Considering I've tried 4 different sets of 4 in 1 drivers and had the EXACT same issue with each one I can't help but rule it out. I'm going to try leaving the case open tonight on the absurd suspicion that it's actually a temp issue (still reads 38cpu/30chassis so it shouldn't be).
I'm at a complete loss and would really appreciate any other suggestions. I don't think there's a hardware failure. I can't find any possible shorts on the board itself which would fit the symptoms. Argh!

KT3 Ultra 2 Problem ?

Last month I built my first PC for my brother. Everything has been working well up until today. The problem I have is that the monitor is displaying "No Video Input" When I boot up the PC there are no Beeps! and the system does not go to POST. I have had a look inside and there is no obvious problem, any help would be appriciated.
Chris

I tried what you suggested, took everything off the Motherboard, removed the CMOS battery and reset the jumper. I waited about 1 hour, and then put it back together with the minimum setup. Power on green lights on the D-bracket then red, going through the boot process, then it stops on three red's one green, which according to the manual means "the memory module is damaged or not installed properly", so I move the stick to the next slot, reboot and it goes back to the original problem two reds on top two green's on the bottom "initialising hard drive controller" and it stuck on that again from power on. Any further suggestions?
Chris

KT3 Ultra 2 Problems, help !!!

I just installed the my new KT3 Ultra2 mainboard but when I boot the screen stays blank and the diagnostics LEDs show 1 and 2 red, 3 and 4 green, meaning according to the manual : " Initialzing Hard Drive Controller" . There it'll stop. The Harddrive itself is ok cause I tried it in my old comp. ...what could be wrong ?

ohh...I forgott, and it makes 2 long beebs !

KT3 Ultra 2 - Bios V5.7 - Problem

Hello,
I don't know if anyone else has tried updating the KT3 Ultra 2 to the new V5.7 BIOS ?
I tried and got load of error messages on the screen, Chipset isn't support etc ROM Size Unknown ....
I have V5.6 on right now.
I have tried Live Update, it doesn't show new bios and also tried another floppy with files on and also downloaded the file again.
No win !

I did not have that particular problem but I found others
I was able to load new 5.7 bios but after I did it took board about 2 minutes to boot.
The part where the XP logo screen is supposed to come up took about 2 minutes. There is no HD (light) activity and then all of a sudden you hear harddrive and XP logo screen comes up and it boots fine.
The same situation arose with Bios 5.6 but I was able to fix that by changing MPS table from Default 1.4 to 1.1. The XP screen would take about 2 minutes to boot so I tried changing settings in bios and finally came to the MPS entry and changed it to 1.1 and the board booted fine. It took about 3-5 sec for the XP logo scrreen to pop up after the last bios screen that would show all the Devices, IRQ's ect...
Changing the MPS to 1.1 in the 5.7 bios did not fix the long boot problem like it did in 5.6.
I can live with the 5.6 bios but the CPU halt command in the 5.7 bios drops temps about 20 degrees F and that is great. I hope this problem can be fixed in 5.7 so I can utilize the CPU Halt command.
My Second Rig: Backup
AMD Athlon XP 2200 (266 fsb)
MSI KT3 Ultra 2
XP Professional SP-1
512mb Crucial PC2700
3 Western Digital HD (2) 80Gb and (1) 20Gb
Enermax EG365AX-VE powersupply
Hercules Gforce 2 GTS/Pro 64mb
Waveterminal 192L sound card
Promise Ultra 133 TX2 card
Intel Pro/1000 MT desktop adapter
Plextor 24x10x32 CDRW
Toshiba DVD
Coolermaster ATC-201 Case
CoolerMaster HHC-001 Heatpipe HS

Big problem with KT3 Ultra (ms-6380e v1.0) after flashing the BIOS (de

Hello out there.
I have a real complicated matter with my Kt3 Ultra board.
Used to work fine, but after I flashed it with the latest BIOS (5.7), the board has this strange behaviour: when I clear the CMOS, the board boots up, when I change & save the settings, the board does not "come to life"(black screen & beeper silent).
It has also this weird problem: it shows garbage charaters on the voltage setting of the CPU. Instead of voltages (i.e. 1.750 etc. etc.) I have only "scrambled" strings.
I had MANY difficulties in upgrading the BIOS because the AMI-flashing utility kept telling me "bios protection enabled) (but there was NO bios-protect setting in the previous bios - I checked a zillion times)...but after trying with different revisions finally I made it.
I already tried everything (re-flashed older bios-es etc. etc.)and I'm starting to feel beat ... if you have any advice, please le me know.
It would be really SAD to put this great board in the garbage-dump....
Bye,
Wyk'03

im having problems with this board as well,
i had no problems with the flash,
i did this...
boot to win me floppy,
copy the flash files to ramdrive, flashed to latest bios..
now windows hangs when i have my ac97 audio enabled in bios...
I WANT MY AC97!
hmmm can you get to a dos prompt from a boot disk?
try re-flashing with 1.0 again and then disable the cmos virus protection thingy, and yes it was there it was in the 1.0 bios on the main screen.

KT3 Ultra2 Problem/Question

Ok, no problem with *NORMAL* working situation.
AMD AthlonXP 2000+ (P.S. LOCKED)
KT3 Ultra2-R
512 MB Kingston PC2700 DDR @ 333Mhz
Leadtek A250 LE 64MB DDR
Enlight 420W PSU
+5v 40A
+3.3v 30A
Problem: I cannot change the ratio of the processor, if I did that then the computer won't start without any beep/screen.
The debug light hung on the IDE detection, but something more weird is before IDE detection there are few more tests need to be pass but it directly going to IDE detection from memory detection. What's wrong?
I need to clear BIOS to make it start again, even I did try lower my ratio.
Is that my processor lock cause this?
Question: Ok, I did search the whole forum, but still cannot find any thread that specified the right divide of FSB/AGP/PCI (Above 133MHz). Does MSI never tell outside how they work on it or what?
Thanks! Anything I missed?

I was able to use my Xp 1600 at the 166 FSB (locked) 166x10.5=1743 Mhz no problem on this board (KT3 Ultra 2). 166 FSB will probably be your sweet spot.
Here is my Madonion Score (12.5K):
http://service.madonion.com/compare?2k1=4427245
I ulocked the chip and have managed 11x166 so far. Now my PC 2100 memory is probably the holdback.
Hey Wonka, what is the highest FSB you've seen somebody clock this board sucessfully at? Do you think if I get PC 3200 mem I'll be able to go to higher fsb than 170? (this board does not work around the 6x mult. point/ 200FSB it can be adjusted to, does it?)
Thanks

KT3 Ultra 2 + BF1942 problems

Hi guys, this is a question for anyone out there that has the KT3 ultra 2 and have tried playing Battlefield 1942. The rest of my specs are:
1900+ XP processor
256MB ram
radeon 7500 LE 64MB DDR
cable modem
The trouble is choppy game play. This occurs in single player mode as well as multi-player so I wouldn't really call it lag. In single player, most of the time the game starts out really choppy but smooths out within a few minutes and is fairly decent for the rest of that map. Multi-player is worse. It's very rare that I can connect and play without lag or a choppy frame rate even with ping times of around 60. It's very frustrating and I know from reading EA's forums that I'm not the only one experiencing this. I'm wondering though if there is anything I can do with my setup to make things better. I disable my firewall and anything else running in the system tray before playing with no luck. Any suggestions?

I enabled sound hardware acceleration from within the game. I'm not sure if it made much of a difference or not. It seemed to be a bit better though.
The bad thing is that I had 3 spontaneous reboots while playing the game spaced about 1 hour apart. :( I did change the memory timings in the bios. I set SDRAM freq to HCLK+33 (I've got 2700 memory). It was set to SPD.
I also set "PCI Delay Transaction" to disabled, it was enabled.
So I'm not sure which of these changes, if any, caused the reboots. The strange thing is that it only seems to be a problem while playing BF1942. I've left the PC on for a few hours doing nothing or web surfing and I've not had any reboots. Microsoft's error reporting thinks it's a device driver error, but doesn't know which one.
Anyone have any ideas?

KT3 Ultra BIOS problem + question

Similar Messages

Maybe you are looking for