KT3 Ultra / Freeze

KT3 Ultra
XP 1700
DDR 256 Ram
80 Gig 7200 Maxor
Xtasy MX 440 Graphics
Was freezing all the time after upgrading bios
Now it seems stable most of the time but
I cannot play halflife thru GameSpy or directly thru
Game Internet Play.
Ran under win 2000 and now under win98
Fast computer NO FUN!!
Thanks for any help.
Andy

Dumped the MX440 (returned to store)
Installed Radeon 8500 LE $20 more bucks
Picked up about 1300 winmarks and been Halflifin
with a smile.
Man this mobo is a fickle sort.

Similar Messages

  • KT3 Ultra-2, Blank Screen then Freeze?!

    Ok, this happend to me last night, and am clueless
    I was playing CS for 1 hr, then suddenly screen went black, no sound, no response. To me my PC frooze, then i hit the reset button.  But then i got a CMOS Invalid Config Error, all the info was cleared?  
    So i re-entered the BIOS SEtup values again, then while checking some info on a webpage, BANG, it happened again, Blank screen, etc etc etc...What is wrong?
    I have DEER 350 Watts psu, 256 Kingston DDR266 CAS2 Module, XP1600+ (not oced) and normal BIOS Defaults (after what happened) and an ATI Radeon 8500LE, and KT3 Ultra-2 Bios v5.6, Windows XP SP1
    Thanks in advance  ;(

    Hi,
    First check your CPU-cooler, if it's mounted wrong the board will shutdown to prevent damage to the CPU....
    Check if the JBAT jumper is set to position 1-2 to safe the data....
    Please read the trouble shooting guide entirely....it might just solve your problem...

  • MSI KT3 Ultra-ARU video lock-ups

    Hello,
        I have a 3 month old MSI KT3 Ultra-ARU.  I am running Windows XP Professional and I am having a periodic lock-up where the screen will show blinking colored blocks and the system will freeze.  Sometimes just hitting reset will cure the problem.  Other times, hitting reset will create two vertical stripes of colored blocks scrolling down the screen.  I have used the board on two entirely separate systems (One with AMD Athlon 2000+, Gainward GeForce 4200, 512 MB Samsung 2700 DDR, Western Digital Expert HD (tried both IDE #1 and RAID controller) (Other System, Athlon 1800+, a different Gainward Geforce 4200, 256 Crucial 2700 DDR, an older Maxtor hard drive).  In either system, every once in a while, the system will freeze as described above (it has happened in Netscape 7.0, Microsoft Word 2000, America's Army game).  
         I have played around with the bios settings, reformatted hard drives, tried various revisions of the nvidia display drivers, swapped out video cards, etc.  Any ideas?  Do I have a bad board?  Do I need to flash the BIOS?  If the board is bad, what do I need to do to return it?
    Thanks,
    Matt Gumaer

    The second system has a 330 watt enermax power supply.  With the new system I put together, I put virtually the same board (MSI KT3 Ultra 2 with bluetooth and RAID), everything is the same as my first system (except the KT3 Ultra-ARU) and the stability is fine.  So, I'm reasonably confident its not the power supply.

  • PSU Query for MSI KT3 Ultra-ARU running 3000xp

    Hi There,
       Before buying a new Motherboard I was just wondering if the problems I'm getting are related to the PSU which is about 5 years old. I've just upgraded my processor to a Athlon 3000 XP 333 FSB which goes into the MSI KT3 Ultra-ARU (MS-6380E v1.X) motherbaord, which I've upgraded the Bios to version 5.7, I've also  upgraded my graphics card to the Leadtek Geforce FX5900XT which also plugs into the PSU. When setting my fsb to 166 my PC either won't boot or when I try to run say 3DMark it just freezes, but when I set my FSB to 133 it works fine. I was wondering if it is trying to draw too much power from the CPU.
       I don't really know how to write the PSU details down correctly so I've just copied everything from the unit.
    Power Man MN :- FSP 300 - 60 BT
    AC Input - 115/230v~, 10/5A, 60/50 HZ
    DC Output - +3.3V  14.0A(org), +5V - 30.0A(red), +12v - 11.0A (yel) + 5VSB
                    -  2.0A (purp), -5V - 0.3A (white), -12V - 0.8A(blue)
    Fuse Rating 6.3A, 250V
    Max Output Power 300W (+3.3V&+5V=150W Max)
    Hope this makes sense,
    Thanks in Advance,
    Paul.

    Thanks for that, What would you got for between these two :-
    is 550w better than 420w? and is ATX 2.03 just the normal ATX size?
    Hiper PSU ATX 420W Active PFC SF-420TS Dual Fan, Silent/Temp Ctrl
    1,PRODUCT FEATURES:
    Active PFC;
    Double Ball-Bearing Fan;
    Dual Fan;
    Gold Plated Connectors and fan grill;
    Adjustable fan speed - Silent function.
    Product Description Hiper 420TS - power supply - 420 Watt
    Device Type Power supply
    Form Factor Internal
    Specification Compliance ATX 2.03
    Output Voltage +3.3, ±5, ±12 V
    Power Provided 420 Watt
    2,Q-Tec PSU ATX 550W Gold PFC Dual Fan PSU for PIII/AMD/P4 CPUs
    PRODUCT FEATURES:
    550 Watt PSU;
    Suitable for ATX systems and Pentium 4;
    2 fans inside for optimal cooling;
    Noise level less than 33 dB (A);
    Complies to latest PFC power distortion standards.
     Product Description Q-Tec Dual Fan Gold power supply - 550 Watt
    Device Type Power supply
    Form Factor Internal
    Dimensions (WxDxH) 15 cm x 14 cm x 8.5 cm
    Input Voltage AC 230 V
    Power Provided 550 Watt
    Thanks,
    Paul.

  • MSI KT3 Ultra ARU - Can\'t install W2K !!

    I've just bought my first AMD powered rig and I'm not able to install W2K pro.   First let me say I'm not a computer novice and have been handling workstation/server hardware/software for years in the Intel world.
    The failure happens at different places in the install, with different results.. sometimes while copying files the system freezes.. sometimes in the middle of a copy i get the BlueSOD... sometimes after copying files when booting into Windows 2000 for the first time the system just reboots to a black screen and is unable to find a boot partition... so we start over and the install deletes copied files and begins again.
    KT3 Ultra ARU
    AMD 2200+
    Corsair CMX512-3000C2
    Pri IDE M - Seagate ST313021A 13GB
    Pri IDE S - Sony CDROM CDU6111-F
    Sec IDE M - Asus CDRW 4012-A
    Sec IDE S - none
    Raid Disabled in Bios
    Followed Mr.Steveo's guides for hardware installation, flashing BIOS from 5.4 (kept a copy) to 5.5.  No problems.
    Followed Mr.Steveo's guide for BIOS settings, using his recommendations to the letter, then after failure changed  SRRAM freq: to HCLK+66 for 3000C2 ram... BUT still fails.
    Additional detail - I lost my original W2KPro CD, and my copy is not bootable... so I'm creating a 2GB DOS partition and booting with a Win98 boot disk to get to the CD and running WINNT from there.
    I've gone through the posts on both the AMDMB and MSI forums and seen some insightful suggestions... but nothing that exactly duplicates by problems.  Hopefully one of you bright bulbs will be able to light my way.  :D
    When I get the BSOD I get different STOP errors:
    0x0000000A  IRQL_NOT_LESS_OR_EQUAL
                (BIOS or Drivers using improper memory address)
    0x0000001E  KMODE_EXCEPTION_NOT_HANDLED
                (A kernel mode process tried to execute an illegal or unknown processor instruction)
    HELP !!

    Back Rev'd the Bios to 5.4 but that didn't help.  Back to the forums...  
    Bas - Thanks for reminding me of the KISS principle (Keep It Simple Stupid).  I had simplified the HW but was still altering the Bios settings to where I know they should be.
    WELL - I HAVE SUCCESS !!
    In further research, (being new to this - remember?) I also find threads saying that I'm supposed to clear the CMOS/NVRAM using a motherboard jumper before powering up the board for the first time and after changing processors.  I don't know how accurate that is - maybe someone will be kind enough to elaborate.  
    I've asked Mr.Steveo in the AMDMB forums if he thinks this step needs to be included in his hardware installation guide.  I followed it religiously in my install and it doesn't mention doing this.
    Anyway, I got the OS installed.  After that, I went back into the Bios and added all suggested settings.  I'm getting "2200+" in the boot screens and in the OS.
    Now lets finish the install and see if we remain stable.  After several days of burnin, I'll OC some to see what I can get.
    Thanks Guys!!

  • MSI KT3 Ultra ARU & GeForce 3 TI200

    A little prob:
    When I run my GF3 in AGP mode, all my games hang after playing 1 min. Then when I change the "Via Tech CPU to AGP-controller" to "PCI standard PCI to PCI brigde" thereby running my GF3 in PCI-mode everything runs fine. Then I went into "dxdiag" and saw that "Acceleration of AGP-struktur" was not availble. So I was thinking, am I looseing enything by running the GF3 in PCI-mode and is it the MSI or the GF3 that is causeing this problem.
    I have tried all the VIA 4in1 drivers and they did not help.
    My specs:
    MSI KT3 Ultra ARU
    Athlon XP 1900+
    Palite Daytona Geforce 3 TI200
    Windows XP pro

    i have the kt3 ultra with a geforce 3 ti200 and it runs flawless.. i use the det 30.30 drivers. one thing i noticed with geforce 3 cards is if i have my agp apperature set to anything but 128 games will freeze and get all kinds off lock ups. if i were you i would look around this forum for the bios setup guide for the kt3 ultra! and set your bios according to that guide
    if you cant find it here goto http://www.amdmb.com and go to the msi forum there and the set up guide is there
    hopefully that helps!!!!

  • MSI KT3 Ultra-ARU with GeForce 4 Ti 4200

    Umm...
    My PC keep freezing when I play a 3D Game like Warcraft III, GTA 3 or Neverwinter Nigths.
    Sometimes it's freezing after 2 mins, sometimes I can play like a half hour.
    When it's freezed, Windows don't work either so the whole comp is messed up then .. and I have to reboot him.
    I post this here cuz I heard that those new GeForce Cards have some compatibilty probs with mainboards ...
    maybe ... someone asked this already ... or just knows a soulution ...
    Hi-Tak
    My Comp:
    AMD K7 1200 "C"
    MSI KT3 Ultra-ARU
    512MB Take-MS Infineon Ram
    GeForce 4 Ti 4200 (Gainward)
    D-Link Ethernet Card
    Tekram SCSI-II Card
    Fortissimo I Sound Card
    Enermax 430W

    hmm...
    I got an Majesty Twins Cooler (TTC-MT1AB)
    that one has ball bearing and everything.
    It's mounted correctly and with silver Thermal Paste
    CPU is constantly at 50 - 55 deegrees
    Chassie at 35 - 40 deegrees
    is this to much??
    I will check again while playin...
    thx for the hint
    Hi-Tak
    Imagination is the Crazyness of your life !!!

  • MSI KT3 ultra aru Western Digital 200GB raid problem

    Hi!
    This is what I've got.
    KT3 Ultra-ARU (MS-6380E)
    AMD 2000+
    256 MB 333mhz RAM (AMD Compatible)
    Seagate ST330630A 30GB (an old drive)
    Maxtor 6L080J4 80GB
    Maxtor DiamondMax Plus9 6Y080L0 80Gb 7200rpm 2Mb UDMA133 Fluid IDE
    Western Digital Caviar WD1800JB 180Gb 7200rpm Special Edition UDMA100 IDE
    Western Digital Caviar WD2000JB 200Gb 7200rpm Special Edition UDMA100 IDE
    Promise 100 IDE-controller
    Creative Geforce MX 440
    Lite-on LTR-40125W
    NEC ND-1300 DVD
    And the configuration:
    IDE1: Seagate (Master)
    IDE2: WD1800BG (Cabel Select)
    IDE3(Raid1): Maxtor 6LO80J4 (Master) and Maxtor 6Y080L0 (Slave) raided as an single drive
    IDE4(Raid2): WD2000JB (Cable Select)
    IDE5(IDE-controller1):
    IDE6(IDE-controller2): NEC ND-1300 (Master) and Lite-on LTR-40125W (Slave)
    And the Software:
    I've updated all the software drivers so I've got the newest and I'm currently runnign Win2k SP3 with almost every patch installed on it.
    And finally the problem:
    When I've hook my WD2000JB to the on-board raid everything seems to be working normaly. The bios finds the drive and makes a new array. Win2k boots up and finds the drive and I can create an partition. But when I've try to format it it the computer starts to freeze for a while and then acts like normal again. The HDD-led blinks as it should during the "normal" time, but when the comp. freezes it stops blinking. The formatation stops at 7% and the HDD-led stops lighting. I don't get an error eventhough it was several hours since it stoped. And the formatation takes like 30min for 1%.
    When I connect the WD2000JB to the IDE3 I can format it and it acts just like normal. I even did a full system test with the System tool found on Western Digitals support site and it didn't find any errors. But when move it to the raid-IDE the errors return. I've get Error reading / writing to disk and when I've did a chkdsk I've got the "Coudn't use Device) so I did a scandisk and it found very very many errors so it completly ereased everything that was on it.
    And when I've run Western Digitals program again i've get an error (Disk error read/writing) error code: 0113.
    Can it be that the Western Disk doesn't work well with Raid? I've haven't heard anything about that, so...
    Best regars,
    Mathias

    You can have a look at my hardware below...
    Chassis: Antec 1080B (300w PSU / 180w COMBINED)
    Mainboard: MSI KT3 Ultra ARU
    CPU: AMD Athlon XP 1800+
    Display: ABIT Siluro GF4 Ti4200 AGP 4X
    DVD/CD-RW Combo: HL-DT-ST RW/DVD GCC-4120B
    Floppy: Panasonic 1.44MB
    HD: Quantum Fireball Plus/AS 30.0GB UDMA 100
    Keyboard: Microsoft Internet Keyboard Pro
    Monitor: KDS Visual Sensations VS-190
    Mouse: Microsoft USB Wheel Mouse Optical
    NICs: 3Com 3C900B / DLink DFE-530TX
    RAM: Micron DDR 266MHz (2x256MB DIMMs)
    Sound: Avance AC'97 Audio
    I've had similar problems where my system becomes very unstable at higher bus speeds. Installing Windows XP simply didn't work very good. However, I have ordered a new PSU today as a solution to this problem. Basically, CPUs and video cards are much more demanding and the more devices you have in your computer the more power you're going to need. I recommend purchasing the Enermax EG465P-VE (FCA) 450W ATX PS. It has a higher amperage rating and will most likely solve your problem.
    Check your PSU and your bus speed settings...

  • KT3 ULTRA 2 / RADEON games dont work

    as soon as i start a game the screen freezes, a few seconds afterwards, the monitor turns itself off and i have to press the reset button...
    I have noticed that if i intall the newer radeon drivers this problem gets worse as it happens to almost every game.  if i use the built in drivers that xp has for the radeon, it only happens about half of the games.
    It also happens in 3dmark 2002. as soon as i press benchmark the monitor turns itself off and i gotta restart.
    i have tried the newest 4 in 1's and it still does this
    i have the latest bios
    i have removed teh sb live card to make sure its not that
    What is causing all this?
    Kt3 Ultra 2
    duron 1200
    radeon 32meg ddr
    sb live
    256 meg samsung 2100
    300W PS

    Have you tried loading the default bios settings and then just changing the fsb to 133? Then check for stability? This happened to me when I upgraded to newer bios and tried running high performance settings in bios.

  • DirectX Problem KT3 Ultra + GForce ti 4600

    Hello,
    I am experiencing serious problems with DirectX (both the built in 8.1 and 9.0b) under XP professional on a computer with the following configuration:
    MSI KT3 Ultra (MS6380E) Mainboard
    MS StarForce GForce4 Ti 4600 Series graphics adapter (it says somthing like N1996 on the board itself near the ce logo, but any help for identifying the board is apprciated)
    I tried every driver I could lay my hands on including older ones like 27.20k, 41.07xp and newer ones like 4345xp or 45.23 (directly from nvidia). Both system and VGA bios have been updated and I downloaded every patsch available from microsoft. I reinstalled my systm from scratch several times while trying ut different combinations. I solved a potential IRQ conflict (built in USB to PCI bridge and graphics adapter both on IRQ 16). I ran across some third party patch called via latency patch wich did not help noticably either.  I tried experimenting with different settings for the refresh rates for the monitor an limitng the DirectX refresh rate to 75, 65 or 60 Hz to no avail.
    Frankly, I am at a loss on how to proceed from here. I reeached a state in the configuation of the system where the problems are "only" the following:
    dxdiag hangs sometimes during the 8.1 and 9.0 tests of direct 3D. Darc Age of Camelot experiences hangups, flickering objects, clutter and some artifacts as well as loss of connection to the server (although my internet connect is unafected) during play depending on how much I reduce the acceleration of the card. On the lowest level of acceleration (no direct 3D) I do not have graphic problems but everything runs so slow it's no use playing at all.
    Please help!
    Andreas

    I did install the 4 in 1 driver early on in the process (must have forgotten to mention it in my post). Just to make sure that I did not miss it in the current installation I reinstalled it again. No major change.
    It seems that the behavior is somewhat eratic. After reinstalling the driver the system (or rather the game) ran for a couple of minutes before it started to freeze again for a couple of seconds each time with increasing frequency of those freezes. Upon leaving the game I noticed again certain flickering objects wich definitely did not flicker when I started. In short the situation got worse with time.
    Since I often tried a lot of things in a row (to no lasting effect) and I think I had the best results after starting afresh after thinking some time about it (with the system switched off) I am starting to wonder if I have a thermal problem or something similar.
    So I did a few tests with the side panel open but I do not think the temperatur is really that high (it's "hand warm" inside).
    Any further suggestions?
    Andreas

  • Kt3 ultra need help! no display

    hey everyone just wondering if any one can help me.
    i have a kt3 ultra (ms 6380e ver. 1.0) with amd athalon 1900+ xp
    512mb if pc 2300 ddr ram. recently my brother told me that the computer crashed and that it wouldn't turn on. after some investigation the computer turns on just no display on the monitor.
    i decided to jumper reset the cmos and try to boot it up. then it beeps 2 close beeps and then followed by another 1 beep. the message on the screen is "cmos settings wrong" F1 to go to setup , F2 load default and boot but no matter which one you pick pretty much the same out come.
    F1 - it brings you into cmos everything looks normal and then once you save and exit the comp restarts and no beeps and no display until you jumper reset cmos again and then the messages come back.
    F2 - it will go through post and then there is a windows bar loading and it freezes there. so you have to restart it and after you restart it the problem comes again. no display and forces you to jumper reset the cmos and the error message comes again.
    i have tried troubleshooting the system.
    -my video card works when i tried it on another computer and with another videocard the same problem occurs.
    -i reseatted pretty much everything, memory, cpu, video card all the cables.
    -i swapped the cmos batterys between the operationg computer and the non operationg battery so that should eliminate the battery problem
    so pretty much what i haven't swapped with a known operationg component is the cpu, ram and motherboard.
    i was just wondering what i should do now??? new motherboard? new cpu? new ram? i hope i can fix it tho.
    any suggestions are very much appreciated thanks

    I have a verry similar problem, tryed with both pc3200 and 2100 ram (the system has been running stable for aprox 3 years now..) i tryed to set the multiplier to 14 (even though its a palomino, and i know that it must be unlocked first) just for fun (cpu temp is 35idle 42load) and it just wont get a signal to the display... i tryed to reset cmos, and to take out the battery.. no effekt at all! my screen is completely black.. any good ideas or just throw the computer in the trash can ? (i dont think its the PSU since it happened when i turned up the multiplier... and it have been stable for so long , a 340W chieftec PSU the kind that came with the dragon series kabinets)

  • KT3 Ultra Always Hang

    I bought my KT3 Ultra in June, ever since then I never enjoy my new system AT ALL. I am having so many problems over it. First, it cant detect my liteon 16x10x40x cdrw. Then, the most annoying problem is that whenever I drag my windows it will freeze the wondows then after a few click of mouse, the whole system hang!!!!
    I have tried to flashed the bios, install the latest VIA chipset and even changed a new graphic card(i first thought it was graphic card prob). But it is still the same result I got. I am now so feddup with it. I tried to go for warranty, and when it is back it is still the same problem over and over. I am so frustrated now. Anyone can help me please???
    Duron 1Ghz
    256Mb Kingmax DDR RAM ( x2 )
    ATI RAdeon 7500
    Sound Blaster Audigy DE
    40gb Maxtor Harddisk
    Liteon 16x10x40x cdrw
    Liteon DVD rom

    I have a similar problem with my KT3 Ultra aru RAID
    I´we found the problem to be the memory, I had a Kingmax 256MB 333Mhz stick... everything OK.
    then I added a second Kingmax stick and I got stuck with the same problems as you are having.
    So I took back the kingmax and changed it to a A-data
    Stick and got the same result, so yesterday I got fed up with this  and got a SAMSUNG 512Mb 333Mhz stick and sold the Kingmax for 30€ (almost free)
    I still got the same problem but I´m going to throw in a clean install of windows and I´m quite sure this will fix the problem.
    My advice to everyone NEWER by KINGMAX. :O

  • AMD XP 2800+ on MSI KT3 Ultra

    I'm going to be placing a 2800+ on a MSI KT3 Ultra tonight.
    These are the steps in which I plan to do it:
    1. Update BIOS.
    2. Reset CMOS
    3: Place new CPU, apply thermal grease, place cooler.
    4: Boot
    If boot -> Set FSB to 166 manually.
    If !boot ->
    1: clear cmos again (power cable out, press start button to empty capacitor, clear with jumper, press start some more, replace jumper)
    2: boot
    if !boot
    1: remove everything from system except CPU
    2: boot and listen to beeps, check leds.
    3: start placing mem one by one, and then other components.
    Any suggestions, things I haven't thought about, thing I really should do etc etc?
    thanks in advance dor any help provided.

    Hi
    Here is the method that I use when I replace a cpu.
    Check the bios settings on the system and write them down before you update the bios.  This way you know what to reset them to after you clear the cmos.  Always clear the cmos with the power cable disconnected.
    Your first four steps are good ones if this is a stable working system.  Never try a bios update on a system that has problems with BSODs, freezes or reboots since it is very easy to kill the motherboard if something goes wrong.
    Unplug all of the drives and leave only the video card and one stick of memory in the system when you first boot it up.  When it starts up enter bios and set the fsb to the cpu fsb and the multiplier to auto. Save and exit  Hook up the drives, load the extra memory, add any pci cards and and start up again.  Go into bios and check the pc health section for temps and voltages.  If they are OK, then finish setting up the rest of the bios with the data you recorded earlier.  Save and shutdown the computer.  Wait 30 seconds to a minute and then start it back up.  You should be good to go this time around

  • KT3 ultra 2 6380E + XP2100

    When I set bios to 133Mhz+auto board finds xp2100no problem,but when I start playing a game the system freezes.If I set bios to 100Mhz+auto board finds xp1500 and I can play as many games as I want.Anybody got any ideas.
    System:
    KT3 ultra 2 Ms-6380E non raid
    xp2100
    512mb pc2100
    60 gig maxtor
    64mbddr geforce4MX440
    sblive5.1
    52x cdrom

    Sorry I haven't replyed sooner work comitments.As for the memory settings everything is set to default in the Bios but I still cant get machine to run games as an xp2100 still freezes.the power supply is a 350 watt unit that came with the case. This is not only powering mainboard and ide devices+sound,lan and vga card but also an extra side case fan and blue neon light . Am I to assume the power supply could be the main problem.
    System:
    KT3 Ultra 2 nonraid
    xp2100
    512 mb pc2100
    60 gig maxtor
    64mb ddr geforce4mx440
    s/b live 5.1
    3com 10/100 lan card
    16x dvd rom

  • Msi kt3 ultra, msi gf4 4200 tvout problem

    I have a msi gf4 4200 64mb card and i have a msi kt3 ultra aru and windows xp,
    my problem is tv out is garbled in pal , ntsc is grey (iam in europe), the colours seem inverted blues are red, etc and theres a ghosting effect around moving images like in videos or around the cursor
    Ive tried everything from default mem setting , to high performance , tried diferent driver sets , tried windows 2000, tried via chipset drivers, latest msi, nvidia gf drivers, pal b , g , i , 60hz, diferent resolutions, clone view, single output to tv, stretch view , nothing seems to fix it, the only thing that comes close to fixing it is using the tvtool http://tvtool.info/ with color fix correction activated, but the images isnt stable its got a weird strecthing, shimmering effect on the bottom half of the tv image
    Iam sure that the problem is not tv or cable related because i tried a friends p4 (board msi sis 645dx) with the exact same model gf4 4200 (not my one) with my scart cable and tv set up and it worked fine.
    Could it be a voltage problem? ive even tried upping agp and core voltage a bit to see if helps, and nothing

    mhuizing,
    nope havent tried a diferent tv , but it should work ,  i tested the connection with a friends computer
    exact same gfx card model and it worked fine!  
    My old system leadtek gf3 ti200 , epox 8kha+ worked fine with this connection.
    Iam using a scart cable to a video , then from the vid to the tv via antena cable
    i upgraded and voila, i got some headaches for free  :P !!!

Maybe you are looking for