Kt3 ultra need help! no display

hey everyone just wondering if any one can help me.
i have a kt3 ultra (ms 6380e ver. 1.0) with amd athalon 1900+ xp
512mb if pc 2300 ddr ram. recently my brother told me that the computer crashed and that it wouldn't turn on. after some investigation the computer turns on just no display on the monitor.
i decided to jumper reset the cmos and try to boot it up. then it beeps 2 close beeps and then followed by another 1 beep. the message on the screen is "cmos settings wrong" F1 to go to setup , F2 load default and boot but no matter which one you pick pretty much the same out come.
F1 - it brings you into cmos everything looks normal and then once you save and exit the comp restarts and no beeps and no display until you jumper reset cmos again and then the messages come back.
F2 - it will go through post and then there is a windows bar loading and it freezes there. so you have to restart it and after you restart it the problem comes again. no display and forces you to jumper reset the cmos and the error message comes again.
i have tried troubleshooting the system.
-my video card works when i tried it on another computer and with another videocard the same problem occurs.
-i reseatted pretty much everything, memory, cpu, video card all the cables.
-i swapped the cmos batterys between the operationg computer and the non operationg battery so that should eliminate the battery problem
so pretty much what i haven't swapped with a known operationg component is the cpu, ram and motherboard.
i was just wondering what i should do now??? new motherboard? new cpu? new ram? i hope i can fix it tho.
any suggestions are very much appreciated thanks

I have a verry similar problem, tryed with both pc3200 and 2100 ram (the system has been running stable for aprox 3 years now..) i tryed to set the multiplier to 14 (even though its a palomino, and i know that it must be unlocked first) just for fun (cpu temp is 35idle 42load) and it just wont get a signal to the display... i tryed to reset cmos, and to take out the battery.. no effekt at all! my screen is completely black.. any good ideas or just throw the computer in the trash can ? (i dont think its the PSU since it happened when i turned up the multiplier... and it have been stable for so long , a 340W chieftec PSU the kind that came with the dragon series kabinets)

Similar Messages

KT3 Ultra: Need help badly!

Hello, folks:
I just bought one MSI KT3 Ultra motherboard. Unfortunately I got a very strange problem. After I turn on the power, the machine can enter the self-test but it will shutdown soon automatically(10 to 60 seconds). I think it is the motherboard which shutdowns the power supply automatically, but why? I am using AMD 1600+ processor and I attached a good fan on it. When I checked the temperature of the processor, it is from 33 to 47 centigrade and it is quite normal. Could you give me suggestions? I am really confused and worried about that.
Many thanks!!
Tao Zhang

I have to ask.. but did you order that mainboard from newegg.com in the last week? I had that exact same problem with 2 Kt3 ultras from Newegg.com ordered last week.. though one would make into windows before it powered down.. my cpu, ram and video card, etc. all worked fine in another machine.. so i ended up sending the mainboard back. I would be interested to know..

Need help on displaying the callers name on ip phone with cme using external directory

Hello Guys,
Need help on displaying the callers name on ip phone with cme while using external directory
Thank you,
Khaja

Thanks for your help,
Does it 100% work with CME. We use SIP and 2ring for external directory? Thanks you.

Hi guys need Help with Displaying Splash Screen?!!?

Hi Guys.
Sorry for the last incomplete post my mistake!
I need help displaying a splash screen as an advertisment or something before i have my main application run.
Here is the code i wrote (it works as if it were a seperate application)
package MajourProject;
import java.awt.AWTException;
import java.awt.Dimension;
import java.awt.Robot;
import java.awt.Toolkit;
import javax.swing.ImageIcon;
import javax.swing.JLabel;
import javax.swing.JOptionPane;
import javax.swing.JProgressBar;
import javax.swing.JScrollPane;
import javax.swing.JWindow;
* @author Matt
public class SplashScreen extends JWindow
    public SplashScreen()
        int UpTime = 20000;
        Start(UpTime);
    public void Start(int UpTime)
        ImageIcon ii = new ImageIcon("src/1.jpg");
          JScrollPane jsp = new JScrollPane(new JLabel(ii));
                JProgressBar Bar = new JProgressBar();
          getContentPane().add(jsp);
          setSize(853,303);
          centerScreen();
          setVisible(true);
               try
                            Thread.sleep(20000);
                           dispose();
               catch(Exception IE)
        private void centerScreen()
                Dimension d = Toolkit.getDefaultToolkit().getScreenSize();
                int x = (int) ((d.getWidth() - getWidth()) / 2);
          int y = (int) ((d.getHeight() - getHeight()) / 2);
          setLocation(x, (y-100));
       public static void main(String [] args)
             new SplashScreen();
}but i now have a problem as i already have a main application done as i wrote this seperately. I now need to combine the two together. So what i did was in my Main Application wrote:
Splash_Screen SS = new Splash_Screen();it then runs my Splash Screen class which i re-wrote to look as such:
package MajourProject;
import java.awt.AWTException;
import java.awt.Dimension;
import java.awt.Robot;
import java.awt.Toolkit;
import javax.swing.ImageIcon;
import javax.swing.JLabel;
import javax.swing.JOptionPane;
import javax.swing.JProgressBar;
import javax.swing.JScrollPane;
import javax.swing.JWindow;
* @author Matt
public class SplashScreen extends JWindow
    public SplashScreen()
        int time = 15000;
        Start(time);
    public void Start(int UpTime)
        ImageIcon ii = new ImageIcon("src/1.jpg");
          JScrollPane jsp = new JScrollPane(new JLabel(ii));
                JProgressBar Bar = new JProgressBar();
          getContentPane().add(jsp);
          setSize(853,303);
          centerScreen();
          setVisible(true);
               try
                            Thread.sleep(20000);
                            dispose();
               catch(Exception IE)
        private void centerScreen()
                Dimension d = Toolkit.getDefaultToolkit().getScreenSize();
                int x = (int) ((d.getWidth() - getWidth()) / 2);
          int y = (int) ((d.getHeight() - getHeight()) / 2);
          setLocation(x, (y-100));
}it obviously runs the default constructor which then runs the other methods in the class but it doesn't seem to show can anybody help me to find out whats wrong? It seems to be there just before the main application launches but only for a split second. And when i am waiting while the thread is sleeping the area i have defined the Content pane for he cursor goes to the loading icon! I don't know if this makes any sence to you but if you can help me it would be most apreciated.
Thanks.

SpearOne wrote:
Hi Encephalopathic
why would it work if i put it in it's own application surely it wouldn't be caused by this thread.sleep?? everything after it is in fact put to sleep. In its "own" application, nothing happens after it is displayed.
if it is the problem then could you please give me some code to add quickly to test??
import java.awt.Dimension;
import java.awt.Toolkit;
import java.awt.event.ActionEvent;
import java.awt.event.ActionListener;
import javax.swing.ImageIcon;
import javax.swing.JFrame;
import javax.swing.JLabel;
import javax.swing.JProgressBar;
import javax.swing.JScrollPane;
import javax.swing.JWindow;
import javax.swing.Timer;
public class SplashScreen extends JWindow
private static final String IMAGE_PATH = "src/1.jpg";
private static final int UP_TIME = 15000;
public SplashScreen()
    Start();
public void Start()
    ImageIcon ii = new ImageIcon(IMAGE_PATH);
    JScrollPane jsp = new JScrollPane(new JLabel(ii));
    //JProgressBar Bar = new JProgressBar();
    getContentPane().add(jsp);
    setSize(853, 303);
    centerScreen();
private void centerScreen()
    Dimension d = Toolkit.getDefaultToolkit().getScreenSize();
    int x = (int) ((d.getWidth() - getWidth()) / 2);
    int y = (int) ((d.getHeight() - getHeight()) / 2);
    setLocation(x, (y - 100));
public static void main(String[] args)
    final JFrame frame = new JFrame("Main Frame");
    frame.setPreferredSize(new Dimension(300, 200));
    frame.setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE);
    frame.pack();
    frame.setLocationRelativeTo(null);
    final SplashScreen splash = new SplashScreen();
    splash.setVisible(true);
    Timer swingTimer = new Timer(UP_TIME, new ActionListener()
      public void actionPerformed(ActionEvent e)
        splash.dispose();
        frame.setVisible(true);
    swingTimer.setRepeats(false);
    swingTimer.start();
}

Need help on "Displaying items for Library System"

Hi folks, i am currently new to this forum and I need help on this problem ASAP.
I currently doing

Sorry, I accidentally hit the enter button so i start again.
I currently doing a online Library system and I hve been assign the task of doing the "search items" use case.
The situation is like this, my system retrieves 50 items based on the user selection and displaying them on a page.
The problem is I do not know how to seperate the items cos I don wan to display everything on the page, wat i wan is like displaying first 20 items on the page and when the user click the "next" link, the next 20 items will be display on the same page.
My teacher ask me to use custom tags(WHICH I NEVER LEARN BEFORE) so
please give me advise or related links as soon as possible cos I have to hand in the project in two weeks time.

Need help in displaying a region in a page

Hi,
I'm looking for the following scenario.
Scenario:_
2 Regions "region_ABC" , "region_XYZ" are dragged and dropped on EM page "PAGE_1". When the "PAGE_1" is displayed first time only the region "region_ABC" will be displayed. When a specific radio button of the "region_ABC" is selected another region "region_XYZ" needs to be displayed in that page "PAGE_1".
I tried to use the Partial Triggers which didn't work. Please provide valuable suggestion/pointers.
Thanks in advance
-Sukumar

Hi Sukumar:
This is the typical case for you to use "Control Flow Case".
You need to create a Bounded task flow say: task-flow1. In this task flow, region_ABC and region_XYZ will be 2 Views in it. Then drag and drop a "Control Flow Case" onto this task-flow1.xml between view: region_ABC and view: region_XYZ. The outcome of the "Control Flow Case" can be anything you like in literal: "ABC2XYZ". Next, go to your region_ABC.jsff file, click on the radio button, and go to its property editor. In the "Action" attribute, put "ABC2XYZ" there.
You drag and drop the task-flow1 onto your EM page "PAGE_1".
That's it!
Good luck,
Alex

Kt3 Ultra ARU help

hallo,
I have this small problem. I seem to be able to boot up however when i reboot it wont boot even past bios. It will only boot when i reset cmos. Also i am getting 2 beeps short pause then 1 beep anyone tell me where to go to find out what this boards beeps stand for?
KT3 Ultra ARU
Ahtlon XP 2200
512 pc2700 ram
GeForce 4 ti 4400

It looks like there is a setting wrong in the BIOS.
When you clear the cmos everything goes back to the default values. Have you checked the Processor settings? Changes are it does not corrospond to the XP2200 (which is a very nice cpu. congrat!)
After you've rebooted the second time, some settings are automatically saved and conflict with your processor, thus no boot.
Which version of the bios do you have? Try the latest version.
Good luck.
Martin

Need help to display content in a KM folder

I need to develop a component which will accept a KM folder name as an input field from UI (for eg : \documents\folder1) and will display all the subfolders and files inside that KM folder along with its details. Need info on how i can implement this and if anyone has already done something similar please help.
Regards
Shabeer
Edited by: Mohammed Shabeer on Mar 18, 2009 5:31 AM

Hi
You can achieve this using KM API's.
Assuming your folder location is /documents/xxx. chekc the sample code below.
IUser user = request.getUser(); //You can use cmadmin service as alternate option//
String location = "/documents/xxx";
IResourceContext resourceContext = new ResourceContext(user);
RID rid = RID.getRID(location);
IResource resource = ResourceFactory.getInstance().getResource(rid,resourceContext);
ICollection collection = (ICollection) resource;
IResourceList resourceList = collection.getChildren(); //Gives list of files and folders inside the KM location//
for(int i=0;i<resourceList.size();i++) {
IResource res = resourceList.get(i);
//Get the required info from the resource object and display
For further details, check the link below
http://help.sap.com/javadocs/NW04S/current/km/index.html
Regards,
Yoga

Need help in displaying error message on the same screen

Hi Experts,
I have written a report which gets called from IW52 by clicking one of the action items. Now in my report when I am trying display an error message it is getting displayed at the bottom of a blank screen. My requirement is to display it at the bottom of the IW52 screen, so that user can rectify the error.
Please help.
Regards,
Sambaran Ray.

Hi,
Probably you need to find a way to enhance the standard code.
But make one thing sure that the code (included bu you) gets fired only when that specific report is being executed. Else it may harm the standard functionality.
Hope this helps you.
Regards,
Tarun

Need help in displaying an Image in a JLabel

Hi everyone,
I am using a JLabel to display images on a particular screen. I am facing some problem while doing so..
On my screen there are images of some garments. When the users select colors from a particular list, i should color this garment images and load it on the screen again with the colors. I have a floodfill class for filling the colors in the images. The problem I am facing is I am able to color the image properly with my floodfill class but when displaying the image on the same jlabel, the image gets distorted somehow.
Everytime I color the image, I create an ImageIcon of the image and use the seticon method from the JLabel class. First I set the icon to null and then set it to the imageicon created. here is the code I use.
If 'image' is the the image i have to load
ImageIcon imgicon = new ImageIcon(image);
jlabel.setIcon(null);
jlabel.setIcon(imgicon);I am setting the icon to null because I have not found any other method to clear the previous image from the jlabel.
Can anyone who has worked on images before and faced a similar situation help me with this?? Is there some other container I can use besides the JLabel to display the images perhaps?
Thanks in advance.....
Bharat

And the thing is when I first go into that screen with the selected colors it is displaying the images perfectly.
It is only giving problems when I pick different colors on the screenit really sounds like the problem is in your floodfill class.
I have no idea what's in floodfill, but if you were e.g. using a JPanel and paintComponent,
you would need to have as the first line in paintComponent()
super.paintComponent(..);
to clear the previous painting.
if not, you would be just drawing over the top of the previous paintComponent(), and if the calculation of the
painting area is not 100% exact, you may get the odd pixel not painted-over, meaning those pixels will display
the old color.

Need help in displaying a feed within my flex app

Hello guys,
I was hoping that someone can push me in the right direction. I am looking to display our feed within our Flex Application. I am using some of the sample from tour de flex
This is what I have so far:
<?xml version="1.0" encoding="utf-8"?>
<s:WindowedApplication xmlns:fx="http://ns.adobe.com/mxml/2009"
     xmlns:s="library://ns.adobe.com/flex/spark"
     xmlns:mx="library://ns.adobe.com/flex/mx"
     width="960" height="850">
     <fx:Script>
     <![CDATA[
          import flashx.textLayout.conversion.TextConverter;
          import flashx.textLayout.elements.TextFlow;
          import spark.utils.TextFlowUtil;
          XML.ignoreWhitespace = false;
     ]]>
     </fx:Script>
     <fx:Style>
          @namespace s "library://ns.adobe.com/flex/spark";
          @namespace mx "library://ns.adobe.com/flex/mx";
          @namespace components "components.*";
          s|WindowedApplication {
               background-color:#000000;
               background-alpha:"0.9";
          s|ButtonBar s|ButtonBarButton:upAndSelected,
          s|ButtonBar s|ButtonBarButton:overAndSelected,
          s|ButtonBar s|ButtonBarButton:downAndSelected,
          s|ButtonBar s|ButtonBarButton:disabledAndSelected {
               chromeColor: #00529c;
               color: #FFFFFF;
          s|ButtonBar {
               chromeColor: #053867;
               color: #FFFFFF;
     </fx:Style>
     <fx:Declarations>
          
          
          <fx:XML id="srv" source="http://feeds.feedburner.com/standforisrael/iWIn?format=xml" />
     </fx:Declarations>
     <s:ButtonBar dataProvider="{myViewStack}" y="175" height="35" width="700" />
     <mx:ViewStack id="myViewStack" borderStyle="none" x="0" y="209" width="700" height="500">
          <s:NavigatorContent id="home" label="Home">
          </s:NavigatorContent>
          <s:NavigatorContent id="about" label="About Us">
          </s:NavigatorContent>
          <s:NavigatorContent id="rabbi" label="Rabbi Eckstein">
          </s:NavigatorContent>
          <s:NavigatorContent id="rabbiCom" label="Rabbi's Commentary">
          </s:NavigatorContent>
          <s:NavigatorContent id="programs" label="Our Blog">
               <s:RichText id="rt5" width="280"
                    textFlow="{TextFlowUtil.importFromXML(srv)}" />
          </s:NavigatorContent>
     </mx:ViewStack>
</s:WindowedApplication>
Now when I run this I get a prompt that is telling me that if the program is already running to stop the program... I have no idea what program it is that i'm running that would prompt that type of dialogue box.
I also get these errors:
Unexpected processing instruction encountered and will be ignored. Found: type="text/css" media="screen" href="http://feeds.feedburner.com/~d/styles/itemcontent.css" IFCJ.mxml /IFCJ/src Unknown Flex Problem
Unexpected processing instruction encountered and will be ignored. Found: type="text/xsl" media="screen" href="/~d/styles/rss2full.xsl" IFCJ.mxml /IFCJ/src Unknown Flex Problem
Is there anything that I am not doing right here?
Any help would really be appreciated,
Thank You

I did try HTTPService but the problem that I was seeing was that I would need to push the information into a datagrid and that really doesn't help me witth presentation of the blog posts.
What if I create a custom component that takes the RSS feed and parses it into sections like so:
Title
Description
Link
Where lets say the title is like so:
[Bindable]
            public var title:String; <-- this is where I get stuck
<s:Label x="0" y="80"
        text="{title}"/>
I would like to also have that title wrapped in a url so that when the person is looking at our RSS they can click either the title or the read more link
What else can i do?

Need help in displaying XML in JSP

Hi there,
i'm a newbi in XML and Java - I have the following prob, think for most of u nothing very difficult (or better thought so, I've posted this question in different forums here, but nobody answers :)
I get an XML response from a search engine, now I want to display the search result in a jsp.
The result is stored in the session [I hope I figured out correctly ;)]
with the following command ->
this.pageContext.getSession().setAttribute(SEARCHRESULT, dSearchResult);
[its from the java class, which generates the result]
Result example ->
<?xml version="1.0" encoding="UTF-8"?>
<FindSearchResult xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="../xml/SearchResult.xsd">
<Result Hits="2" Name="OfficeLand_en_US">
<Items>
<Item Score="250">
<Field FieldNo="0" Name="ProductID">KqvAqAB1Tq0AAADnFthtpZvC</Field>
<Field FieldNo="1" Name="CatalogCategoryID">gh0KAAFvj3wAAADiW8SMtr6o</Field>
</Item>
<Item Score="250">
<Field FieldNo="0" Name="ProductID">4rwKAAFvtNYAAADiwdCMtr6o</Field>
<Field FieldNo="1" Name="CatalogCategoryID">gh0KAAFvj3wAAADiW8SMtr6o</Field>
</Item>
</Items>
<HitDistribution>
<Hit Hits="75" Score="0"/>
<Hit Hits="2" Score="250"/>
</HitDistribution>
</Result>
</FindSearchResult>
How many 'Field' elements exist, depends on the query.
The result example is a response, which is send to my JSP page. It is stored in an variable under the name SEARCHRESULT (it's the result of a query in a search engine).
My JSP page is the page, which should display the searchresult.
So i need to know, how to programm something in my JSP page to check the SEARCHRESULT to display not the whole xml file. I just want to display all Items (compare with result example) -> The name of each existing FieldNo, the Score and the HitDistribution.
Please help me :)

hi there,
first create a xml schema for the xml you will be receiving.
use jaxb or castor with the schema and create a class.
in your jsp unmarshal the xml result you are getting with the class
generated by either jaxb or castor. the class will have methods that return you the required elements.
get to know xml schema better and just a pass thru of jaxb or castor will solve the problem.
vedha_g

Need help in displaying multiple attachments in a OAF Page

Hi,
I need to display attachemts of requisition line in a OAF Page(Notification Detials Page)and the attachments can be more than one.My custom VO returns it as a single string like url1, url2.. etc.
I need to show them as seperate links.
I tried using the Item Style as LINK.But it is not working.It is prefixing the server url before the View Attribute and creating a single link.
Any help in this regard will be appreciated.Thanks in advance.
Srini

Hi skeerthi,
If you are using the core attachments table (FND_ATTACHED_DOCUMENTS and the like), you can have a look on the Developer's Guide on chapter 4: Implementing Specific UI Features, section "Attachments", there is a seeded region available for displaying multiple attachments.
If you are not, then i'd recommend refactoring :D... Just kidding, it would be nice to use the core feature, but if the table is custom, and the links are stored separated by commas, you will have to write controller code to implement that. That can be done by:
1) Creating an Application module method that uses StringTokenizer to tokenize the attribute String (use getViewObject().getCurrentRow().getAttribute() to get the comma-separated value) and return that to the controller
2) In the controller, receive the StringTokenizer and for each token, use the api createWebBean() to create an OALinkBean and add it to a layout region using addIndexedChild() api.
This way you will dinamically create a Link for each attachment. If your layout region is, for example, tableLayout, you can create a rowLayout for each token, then create a Link, add the link to the row layout and finally add it to the tableLayout. By doing so, you will create a table-style attachment region.
Hope it Helps
Thiago

Need help in displaying Rows to Columns

Hi,
I am facing problem in displaying Rows to Columns
I am using pivot function:
select *
from
(select vendor_name
from tablea)
pivot
(count(vendor_name)
for vendor_name in ('a,b,'c'));
its working fine showing vendor_name and count
but when i want to display the output as:(How to include the Salalry column in the query?)
Name:{a b c}
Sal Total:(400,600,800}
Any help will be needful for me

Not sure what you mean:
select *
from (select deptno,sal from emp)
pivot(sum(sal) for deptno in (10,20,30))
10 20 30
8750 10875 9400
SQL> SY.

Need Help in displaying data labels at the top of the bars in CFCHART

Hi,
I have a cfchart with two line series and one bar. I want to display the data values at the top of the bar and the line series. Below is the XML I am using:
<cfsavecontent variable="chartStyle">
<?xml version="1.0" encoding="UTF-8"?>
<frameChart is3D="false" isMultiline="true">
          <frame xDepth="12" yDepth="11" outline="black" stripColor="light_gray">
               <background maxColor="black"/>
          </frame>
<yAxis scaleMin="0" scaleMax="30">
               <labelFormat pattern="###"/>
<parseFormat pattern="###"/>
<labelStyle orientation="Horizontal"/>
<titleStyle font="Arial-11-bold" isMultiline="false"><![CDATA[
#Vehicles       ]]>
</titleStyle>
</yAxis>
<yAxis2 scaleMin="0" scaleMax="30">
               <labelFormat pattern="###"/>
<parseFormat pattern="###"/>
<labelStyle orientation="Horizontal"/>
<titleStyle font="Arial-11-bold" isMultiline="false"><![CDATA[
Profitability       ]]>
</titleStyle>
</yAxis2>
<dataLabels foreground="black" font="Arial-12-bold"/>
<legend allowSpan="true" equalCols="false" halign="Center" isMultiline="true" placement="Bottom"><decoration style="None"/></legend>
<elements place="Stacked" drawOutline="false">
<series index="1" place="Stacked">
<dataLabel style="value"/>
</series>
          <series index="2" place="Stacked">

</series>
<series index="3" place="Stacked">

</series>
<series index="0" place="Stacked" shape="Line" isSecondAxis="true">
<dataLabel style="value"/>
          </series>
<series index="1" place="Stacked" shape="Line" isSecondAxis="true">
<dataLabel style="value"/>
          </series>
</elements>
          <table>
               <heatmap isEnabled="false" minLevel="0.0" maxLevel="0.0"/>
          </table>
          <popup background="white" foreground="black"/>
          <paint isVertical="true" min="26" max="76"/>
          <insets right="5"/>
</frameChart>
</cfsavecontent>
Can anyone please tell me what is the mistake i am doing.
Thanks in advance,
Jeevan Pulugu.

Hi,
Probably you need to find a way to enhance the standard code.
But make one thing sure that the code (included bu you) gets fired only when that specific report is being executed. Else it may harm the standard functionality.
Hope this helps you.
Regards,
Tarun

Kt3 ultra need help! no display

Similar Messages

Maybe you are looking for