Kt3 ultra2 + MSI 8348A CD/RW problem

i don't know why but when i check settings for CDRW, it's running only in PIO mode...i suppose this writer supports UDMA33 mode, am i right? does somebody knows where's problem?
my system:
XP1600+, kt3ultra2, 256 MB pc266, maxtor diamax+ 30GB, windows XP + service pack 1
thank for answer...
have a nice day

You can change it to DMA mode.
Device Manager -> IDE controller -> Primary/Secondary IDE Channel -> Advanced Settings -> Transfer mode "DMA if available"
Or you have already set and it is still PIO mode? Try to update the IDE controller driver again by manually selecting from the driver list.

Similar Messages

Msi KT3 MoBo / MSI geForce4 TI 4200 Problem

Hello, hopefully someone can help me. I am having a rather unusual problem. Least I think it is. I have a MSI kt3 ultra2 motherboard, 512 meg ddr 2100 crucial ram. AMD XP 2000+ CPU and an MSI Geforce4 TI4200 video card. First of all, what agp settings should i use? 4x? 2x?. Secondly, should i enable agp fast writes? And last, what are the other 2 settings in the agp setup in the bios which are like 1/2 or 2/3?
I also ran mad onions 3d mark 2001 SE and got a score of 4898! This seems a little low to me. Comparing online, I should be getting scores rannging from 9000 to 13000. I have installed Nvidia Detonator drivers but they are the latest beta drivers. Are these bad drivers? None of my games ever freeze except for Soldier of Fortune 2. It slows way down and when i ctrl+alt+del, it says i am using 100% cpu usage. Can anyone help me? I just want my system i bought a week ago to run at its full potential and have nowhere else to turn.

I am using Windows XP Pro. I am running the 3d Mark 2001 SE with a 1024 resolution and no AA. I am also using a 32bpp color depth. The defaults when you load the program up for the first time basically. I never did get a patch for SOF II although I should have. Man do I fell like such a n00b.
Hey Jamie B, you said i should "disable support for advanced cpu controls is NOT checked". Where is that at?
Thanks to all who have replied. :D I appreciate it.

KT3 ultra2 with amd barton 3000+ problems

Ok so I upgraded from a 1800+ to a barton 3000+, and im having problems running the chip. Iv set the fsb to 166, the ram to HCLK, tried running with just one stick, it runs for about 5min then restarts. Any ideas?
System specs
Msi kt3 Ultra 2 (newest bios 5.7)
Msi GF fx 5900 not overclocked
2x 512 pc3200 ram, one stick is kingston other is OCZ
Sound blaster Audigy
Enermax 365 watt pws
20gb maxtor hd (lol)

Well if you purchased an Athlon XP 3000+ which is a 400mhz chip and are trying to run it at 333mhz instead of 400mhz that might be the issue aside from the fact that the KT3 Ultra2 does not support that chip so it could also be a bios issue.
I retract a little of that. There is an Athlon XP 3000+ 333mhz chip. But are you sure this is what you obtained? If not that is your problem.

KT3 Ultra2-Geforce4 MX 440- Direct3d problem

I got problem using direct3d : when I try to test direct3d with dxdiag, the test is directly canceled with the popup message " Tets canceled, key pressed" (Not exactly this, it's in french here :-) )
Here is my config :
AMD Athlon 1800+
512 RAM ( DDR )
WIN2000 SP3
MSI KT3 Ultra2
I have installed the lastest drivers from nvidia site
I'm waiting for your help. I really need it.

Thanks for your help, I've found the problem.
In fact, there was 2 problems :
1- Network card in PCI slot 1 --> moved to the 2.
2- Keybord manager problem --> I have to close the service in the task bar, near the clock.
Now it works, but I dont't know why this keyboard manager hangs.
Again, thanks for your help !!

Msi kt3 ultra, msi gf4 4200 tvout problem

I have a msi gf4 4200 64mb card and i have a msi kt3 ultra aru and windows xp,
my problem is tv out is garbled in pal , ntsc is grey (iam in europe), the colours seem inverted blues are red, etc and theres a ghosting effect around moving images like in videos or around the cursor
Ive tried everything from default mem setting , to high performance , tried diferent driver sets , tried windows 2000, tried via chipset drivers, latest msi, nvidia gf drivers, pal b , g , i , 60hz, diferent resolutions, clone view, single output to tv, stretch view , nothing seems to fix it, the only thing that comes close to fixing it is using the tvtool http://tvtool.info/ with color fix correction activated, but the images isnt stable its got a weird strecthing, shimmering effect on the bottom half of the tv image
Iam sure that the problem is not tv or cable related because i tried a friends p4 (board msi sis 645dx) with the exact same model gf4 4200 (not my one) with my scart cable and tv set up and it worked fine.
Could it be a voltage problem? ive even tried upping agp and core voltage a bit to see if helps, and nothing

mhuizing,
nope havent tried a diferent tv , but it should work , i tested the connection with a friends computer
exact same gfx card model and it worked fine!
My old system leadtek gf3 ti200 , epox 8kha+ worked fine with this connection.
Iam using a scart cable to a video , then from the vid to the tv via antena cable
i upgraded and voila, i got some headaches for free :P !!!

BIG problem with MSI kt3 ultra2 Help

First, hi!
I got a MSI KT3 ultra 2 mainboard (at least it's what it is on my mainboard)
MS-6380E ver 1.0
i go on the Website.. AND the Kt3 Ultra 2 board, does not look like mine!
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=341
(i have almost the same thing,but without the 2 EXtra IDE,and i dont have a FAN but a MSI DDR orange heatsink) it is wrote the model number in the SAME EXTACT WAY ( MS-6380E ver 1.0 and kt3 ultra2,above),u can see it by checkign the large pic.. And on that page it say my mobo KT3 ultra 2 support fsb 333
But
IN my book (my mobo book) it say that my mobo don't support FSB 333 (it is important i just brought a 333 cpu) so WHAT THE FCK? i checked on the site
and i found this mobo:
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=11
Wich look like mine, and have the specs it got in my book... BUT HOW COME its not KT3 ULTRA 2 and just a kt3 ultra? (remeber on my mobo its a kt3 ultra2)
Damn , i know its a bit complex.. but to make it short if youve been lost
THE KT3 ULTRA2 SPECS IN MY BOOK (USER GUIDE)ARE NOT THE SAME THAT ON THE WEBSITE, ON THE WEBSITE I WOULD HAVE THE KT3-ULTRA (NOT 2) but when i look on the KT3-ultra the model number.. it's not the same as my mobo...
So i would like to know Does my mobo support the fsb 333LIKE A KTA3 ULTRA 2 SHOULD DO ? (prolly not,but lets hope)
thx for yer help

Maybe it is good news
Hey.. is it normal.. i just noticed that
what is wrote between my PCI slots ( KT3 ULTRA2 ) is kinda wierd
the KT3 ULTRA is in WHITE then just beside there is 2CE in orange
so it make it KTA ultra 2 CE (but what the CE stand for,and why my 2 and CE are in orange,as if would be a little sticker,but its not,i just checked)
and i saw on this card : THIS
that the 2CE is in white.. thats the only difference with the 2 extra ide.
And if someone could confirm what the guy above stated that it will work even if its a wierdo board at 166 mhz.. thx you

Problems w/ KT3 Ultra2 w/R

I think the best thing to do it's to explain the problem from the beginning.
A couple of months ago I bought my computer by components and put it togheter myself. Everything was fine, but there was a problem. Back then, my mobo was an ABIT KX7333R and it wouldn't boot if I changed the processor speed in the bios (it booted allright with the defalut -XP 1500- but when changed it to the real one -XP 2000- it didn't boot at all). So I used it for about 3 weeks with the default setting (I was too lazy at that moment to change the damn thing) and one night, the computer died while I was using it. Anyway, I assumed twas the mobo, so I requested a RMA from Abit, and had my motherboard replaced. The replacement worked fine for about 10 minutes, and when I was writing an email, puff, died again. At that time I was swearing and cursing, and blamed Abit. By then, I was tired of waiting and everything (just got stressed) so I ordered an MSI KT3 Ultra2 with raid. When I first booted the PC, the motherboard didn't recognized my HDD when I entered the Bios. I tried restarting, but the pc would not respond. So I checked the D-Bracket lights and they say that the problem was in the IDE controller or device. So I replaced my HDD with another one, but nothing happened.
So, my questions are:
1- Am I the guy with the worst luck in the world and got three defective motherboards in a row?
2- Could it be that something else in my PC is causing the problem?
If you have any questions, please post it here and I'll answer them. Here it's my computer components:
Athlon XP 2000
MSI KT3 Ultra2
Gainward GF4 TI4200
SB Audigy Gamer
3COM Ethernet card
Corsair XMS PC2700 512MB (Silver heatspreader)
Turbolink 420W PS
Lite-On CDRW
PS: Sorry for the length...

Have you tried with another CPU ? If not, please do so ; or return the CPU for RMA.

BIOS Settings Problem on KT3 Ultra2 MS-6380E with Barton 3000+(FSB333)

Well, I finally got my Barton 3000+ with 333 MHz FSB and installed it yesterday in my MSI KT3 Ultra2 Mainboard....
System Before changing anything:
PSU: DTK 400 W
+3.3 V / 22 A
+5 V / 35 A
+12 V / 15 A
-5 V / 0.5 A
-12 V / 0.8 A
+5 V VSB / 3 A
So that should make up 400 W as far as I know, my total System drain should be around 300-350 W so even if it would not suffice 400 W it should run the system ?
Mainboard: KT3 Ultra 2 (BIOS v5.7)
CPU: AMD XP 2100 FSB 133 MHz
RAM: 1.536 MB, 3x512 MB Infineon PC3200 (400MHz) CL 3-3-3-8 @400MHz, Cl2.5-3-3-7@333Mhz, 2-2-2-6@266MHz
VGA: MSI RX-9800 Pro 128 MB
DVD/CD-R/RW-Combo: Plextor PX-708 (Firmware 1.08)
CD-R/RW: TEAC CD-W540E (Firmware 1.0K)
Storage: Western Digital WD800BB (80 GB) (Firmware 17.07W17)
USB-Storage: Maxtor 4 K080 H4 (80 GB)
Monitor: Samsung Syncmaster 172T with Driver Version 1.0
Printer: HP Deskjet 970Cxi with Original HP Driver Version 4.3
OS: Windows 2000 Professional with Service Pack 4
BIOS Settings: SDRAM 1T Command: "Disabled" It won't work stable with 3 RAM's in it with that setting, but that I did know before.
CPU Fast Command: "Ultra"
System was running stable for nearly 2 years with this Configuration:
So now it goes:
First I changed the CPU form my old AMD XP 2100+ to the new Barton 3000 + with its new Arctic Cool Copper Silent 2TC.
Then I went into BIOS and raised the FSB to 166 MHz, which should be the correct one, or do I have to put 167 MHz in there (since 166.666666 MHz is rounded to 167)?
Then I exited and watched the restart...but it didn't start-up it only got me 3 long beeps at the HOST.
After some whining and beating I plugged out anything and cleared CMOS and started the whole thing again:
System after Clearing CMOS:
Mainboard: KT3 Ultra 2 (BIOS v5.7)
CPU: AMD XP 3000+ FSB 100 MHz
RAM: 1x512 MB Infineon PC3200 CL 2-3-3-7 (BIOS setting CAS Latency by "SPD")
Storage: Western Digital WD800BB (80 GB) (Firmware 17.07W17)
Monitor: Samsung Syncmaster 172T with Driver Version 1.0
OS: Windows 2000 Professional with Service Pack 4
With all Default settings, the Computer boots up, and is correctly Recognized as a Barton 1300 MHz.
When increasing FSB to 133 MHz it is correctly displayed as a Barton 2200+
NOW...
...after adding one BIOS setting after another I narrowed the problem down to the "CPU Fast Command (decode)" Function...if set to Ultra it does not boot-up when running 166 MHz FSB, it does not even let me into BIOS. I have to clear CMOS and restart from scratch again...
Is this normal and expectable with a Barton 3000+ running at the native 166 MHz FSB or not ?
Since my system before was running on "Ultra" with my old AMD XP 2100+.
There is only one more thing I noticed, the CPU V-Core is shown to be only 1.616 V (setting on "Auto" but it should be 1.65 V ? Should I increase the V-Core to 1.675 V in order to get closer to 1.65 V or shouldn't I worry about ?
Thanks for any Input you can give me on the problem.
Iscaran

Iscaran, you are indeed correct in the statement which you made
Quote
...after adding one BIOS setting after another I narrowed the problem down to the "CPU Fast Command (decode)" Function...if set to Ultra it does not boot-up when running 166 MHz FSB, it does not even let me into BIOS. I have to clear CMOS and restart from scratch again...
This setting can be set to fast/ultra on the KT3 Ultra2 when using PC2100 ram running at 266. However, when using PC2700 ram running at 333, this setting MUST be set to normal for the satisfactory operation of the board. I know that you have PC3200 ram actually installed but it is only running at 333.
Quote
Is this normal and expectable with a Barton 3000+ running at the native 166 MHz FSB or not ?
Yes, absolutely normal
Quote
There is only one more thing I noticed, the CPU V-Core is shown to be only 1.616 V (setting on "Auto" but it should be 1.65 V ? Should I increase the V-Core to 1.675 V in order to get closer to 1.65 V or shouldn't I worry about ?
How are you measuring this ie Bios or o/s utility? Not unknown that these are incorrect. However, if you feel unhappy about this, try setting the V-core manually to 1.65v and check what this gives.
Quote
So 3.3 V x 22 A gives 72.6 W, that could be really a little cutting the edge. Could that cause the board to not respond when setting the "CPU Fast Command" to "Ultra" ?
Getting a more powerful psu will not likely cure this well documented problem.
However, this board mostly draws power from the 3.3 & 5v rails. The 12v is mostly used to power HDD, optical and fans. When you consider that 128Mb of ram draws about 8-10w from the 5v rail and you have a total of 1.5Gb that adds up to 96-120W of juice just for the memory alone. This board will beep at you at o/s level when it's running underpowered but my opinion is the same as osnavi's your 3.3v & 5v rails are too low. Also what is combined 3.3v & 5v wattage. What kind of reading do you get on monitoring utilities.
By the way I have as you can see from my dets below the same board and cpu as you and when I changed from a XP2000 Palomino with PC2100 ram to XP3000 Barton and PC3200, I changed the 'Fast Command' setting from 'Fast' to 'Normal'
Hope this helps, enjoy the board

KT3 Ultra2 R and VGA problem

I wonder if I could please get some ideas as regard this rather odd problem which I am encountering. This problem occurs when while the pc is 'shut down' if I disconnect the power supply ie switch off power by way of the switch on the psu. When I switch power back on again and boot, the pc begins its booting sequence it begins to launch windows and then it stops and a little red square (with a bit of green) appears in the top left hand corner of the screen. Now this problem does not occur if I shut down the pc normally (but don't cut off power supply). I have several partitions on my HDD and they are all affect at the same time. The end result is that I boot into safe mode I look at the refresh rate which is set to 'unknown' change it to 'adapter default' then reboot but upon reboot I get windows displaying screen at 640x480 with standard vga colours. I check in device manager under 'display adapters' what driver it's showing and it's the driver which I last loaded ie the correct one. I cannot change screen resolution , bit colour and the refresh rate only allows for 2 options, either 'optimal' or 'adapter default'. In order to get back to where I was, I have to remove and re-install my VGA driver and then everyting is back to normal (until I switch off power again at psu then back to square one). I have spoken to the manufacturers of the graphics card and they say that if the card works ok when I shut down pc normally and restart then cannot be the card. I described my problem in greater detail to MSI support and they said either VGA or O/S.
In essence I wanted to isolate the problem to, is it 'hardware or 'software'.
I would be grateful if anyone can shed some light.
KT3 Ultra2 R (5.5 not the right one but the cpu clock speed is correct at post)
XP 2600+ 333 T'Bred
Crucial 512 Mb PC 2700
Leadted Ti 4400 128 MB Vivo (det 44.03)
Creative Audigy
Enermax 432W
Windows 98SE (via 4-1 v 4.34)
Seagate 60Gb 7200rpm I am running the HDDs as independant drives on the
Seagate 40Gb 7200rpm Raid controller ie one on IDE3 & one on IDE4

Odd as it might seem I have to follow the proceedure listed below if I want to switch off power altogether to work on my pc.
1. Cold boot system with 166FSB and let O/S install
2. Reboot enter Bios and reduce FSB to 133 make sure to set memory speed as HCLK and let O/S load
3. Shut down and switch off power supply
4. Reconnect power and boot system. Enter bios set FSB to 166 (the mem speed will be HCLK)
5. System continues to boot and loads O/S
From that point on, cold boots (without cutting power supply) are not problematic as once the 166FSB is 'registered' everything works ok (at every cold boot). So anytime I wanna work on my pc I guess I have to do the above 5 steps. They seem to work but need to try it out a few more times before I am confident that this process will always work.
I am sure you agree that this is one strange mother of a problem.
I suppose the only 2 things left are a total O/S reload or trying another 333 cpu because I have tried everything else. I guess I will have to live with it.
I have also cut some additional front vents so that front fan draws more air in and it appears to have dropped my idle Temp to 40.5C on CPU (running at clock 2083Mhz).
As as said earlier in my post my system ran perfectly with XP2000+ and 512Mb PC2100. I merely upgraded the CPU to XP2600 and mem to PC2700 and it has thrown up this very odd problem. And to boot (if you will pardon the expression) when I first installed new CPU and memory it booted first time at 166FSB. osnavi, in case you upgrade your CPU to a XP2600 and you get this weird problem at least you can come back to to this thread and find this workaround.
I wonder if anyone can fathom out why this is happening.......If not as I said I can live with it.
wonkanoby, I will try the link to the memtest. That is the only thing I have not tested so will give that a try.
-MSI KT3 Ultra2 Raid
-AMD XP2600+ 333 T'Bred
-Evercool CUD 725 Cooler
-2x256 Mb PC 2700 Crucial
-Leadtek Ti4400 128Mb Vivo
-Creative Audigy
-LiteOn DVD 16x
-Liteon CDR48125w
-HP CDR 9710i
-Seagate Barracuda IV 60Gb (I am running the HDDs on the raid
-Seagate Barracuda IV 40GB controller as 2 independant drives)
-2 Case fan
-Enermax 431W

MSI KT3 ULTRA2-C and AGP compatibility

Hi, I'm just about to buy a new motherboard these days, MSI KT3 ULTRA2-C, with an XP 2000/2000+ and memory, but not a new video card, since i can't afford it right now. I only have an AGP Creative 3D Blaster Banshee 16 MB, but it is a 3.3v agp card (AGP 1.0). I was wondering if this motherboard can support it, i checked in a lot of places, including the manual and it doesn't say anything about the voltage it can take, neither if the AGP slot is universal or not (i.e. if it can support both 1.5/3.3v or only 1.5v). The manual for the KT3V specifically says '4x 1.5v only', but this one just says 'AGP 2.0 1x/2x/4x'. I really need to know this since otherwise i'd have to wait two months to afford another video card. I also checked another post here with an answer to a page with AGP explanation, but it didn't help. Thanks you very much, really

One AGP slot
- AGP (Accelerated Graphics Port) specification compliant
- Supports AGP 2.0 1x/2x/4x
so whats the problem,your fine there
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=357&MODEL=MS-6593

Kt3 Ultra2-R W2K & XP problem

Hi all,
This is my first post! I have been scouring the board now for quite a while looking for an answer but to no avail, so I decided to post.
My problem is this: I just bought some hardware to put together a new machine. Thing is it won't let me install w2k or xp. I was able to get w98se on to it but then when trying to upgrade to w2k or xp the computer usually shuts itself down when either of the OS's try to analize the machine.
I don't think it's a power problem as it runs in w98se fine, that is until you try to install some software, then it usually shuts itself down. Another thing is when w98se boots up and asks for a username & password, if you don't enter the password real quick it'll shut down.
This is driving me nuts ;( Please help me!
Here is the spec:
AMD Athlon XP2200+ 1.8 GHz 266 MHz bus Socket A (Thoroughbred) Processor (OEM)
Cooler Master CPU coole Socket A/7/FCPGA DP5-7H53F-0L, to 1,4GHz and XP2200+
DDR-DIMM PC2700 256MB DDR CL2.5 Generic Memory 184-P (for DDR-PC333MHz)
MSI KT3 ULTRA2-R Mainboard with sound VIAKT333, ATA/133,Raid, ATX, USB2.0
Creative gForce 3 Ti200
30gig maxtor HD.
CD-ROM, ZIP Drive and floppy drive from an old machine.
Thanks for listening!
B.M.

Hey wonkanoby,
I just whipped this off the site where I purchaced the goods. I don't have the machine in front of me so can't look any closer. By the way I'm pretty much a newbie to this trouble shooting stuff, so please bear with me if I don't understand some of the jargon!
Product Description:
Q-Tec Pro Line Black 6023MD - mid tower - ATX
Form Factor System cabinet - mid tower
Dimensions (WxDxH) 19 cm x 43 cm x 43 cm
Supported Mainboard Form Factor ATX
Enclosure Color Black, silver metallic
Power Provided 350 Watt
Voltage Required AC 230 V
Thanks,
B.M.

MSI kt3 ultra2-R

got a question regardingh this board... does it support pci divider change over 133 fsb to 1/5... i've got AGOIA Athlon XP 1600+ which goes to 1,77 with no problem but (according to si soft sandra) the PCI goes a little to high (over 42 Mhz)....

It's not the problem with any program to show the chipset fan speed. It's the chipset fan speed is not monitored by the board at all. The board only supports 2 fan speed monitoring - CFAN1 and SFAN1.
So far none of any software read the PCI divider correctly. MSI didn't implement 1/6 PCI divider on KT3 Ultra (1) board, but unknown for KT3 Ultra2. Even yes this board is hardly reach stable at that speed too.

MSI KT3 Ultra2-CLS and 166Mhz FSB

I own a KT3 Ultra2-CL and a Athlon 1400C.
At the moment it runs 11,5x133 = 1533Mhz. Stable.
It also runs 9x166 = 1500. Stable, but my PCI runs 41Mhz.
So please implement the correct divider in very near future bios update.
It should not be true that customers, who invest less money in a new mainboard than others, can´t use all of the functions the chipset provides. I WANT TO RUN 166Mhz FSB WITH 33Mhz PCI
All of your "expensive" boards provide this divider.
IS THIS MAREKTING 2003???
Best regards

One AGP slot
- AGP (Accelerated Graphics Port) specification compliant
- Supports AGP 2.0 1x/2x/4x
so whats the problem,your fine there
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=357&MODEL=MS-6593

KT3 Ultra2 mobo problem or others problems

My PC as below;
AMD Athlon XP 1500+ @ 1333 MHz (with box)
MSI KT3 Ultra2-R Ver 1.3 (Bios-Ver5.6)
256 MB Kingmax PC2700
Leadtek WinFast A170 SDR
Creative Sound Blaster Audigy DE Special Edition
40 GB Maxtor D540X Hard Disk Drive (5400RPM)
40*12*48 AOpen CDRW Drive
300 watt Enlight EN-8304946 (Model:HPC-300-101) PSU
+5V= 25A +5V;+ 3.3V=180W max
+3.3V =20A
+12V=13A = 156W
-5V=0.3A = 1.5W
-12V=0.8A = 9.6W
+5VSB =1.5A =7.5W
Blower Fan: 6 Fans (Using other cheap ATX PSU modify by myself)
P/S: no include CPU Fan ,VGA Fan ,Chipset Fan
Drivers & Software:-
Windows XP Pro + SP1
Nvidia 40.72 Driver
VIA 4.43
Power DVD XP
My problem like this; yesterday I playing Audio CD using Power DVD XP, then suddenly the application not respond , so I reset the computer . After booting ,the hard disk can not detect. So turn off the system without do any thing ,let rest 10 minutes & turn on, the hard disk can detect ,so go to windows again, try play cd again, but after this the system was not respond same like above problem .so reset the pc ,after booting the computer can not detect the hard disk again. So I turn off and until today in morning .I turn on my pc,after booting the hardisk can detect.but can’t go to window anymore, because all inside my hdd
was lose, my D Drive data also missing (I got 2 partition-1st partition-C Drive: OS+ Software; 2nd partition -D Drive :MP3 song +My document).But I go to FDISK ,can’t access drive.
This problem I not sure is hard disk problem or power supply problem or mainboard problem. But can’t be the power supply not enough power, because I just have 1 HDD , 1 CDRW Drive,1 Floppy, Mainboard with 1 chipset fan ,AMD Athlon XP1500+ c/w original fan ,VGA+VGA fan & sound card only. But my cousin using P4 2.4 GHz using cheaper & no name PSU with 300watt only and have more drive&may cards:1HDD(7200rpm)+HDD Fan,1CDRW Drive,1 DVD ROM ,1 Geforce2 display +FAN ,1 creative sound card, internal modem & network card. So I think the PSU is no problem and this PSU ,I have check from AMD site ,this PSU recommended by AMD and can support AMD Athlon XP 1500+ to 1700+ only.
But got one time, my pc have usb keyboard problem ,during system restart with press reset, after booting ,the pc can’t detect the keyboard ,and I have enable the legacy usb support , the problem I solve just change PS/2 keyboard only ,after this was working fine. look like same problem but how solve?????
But until today this problem happen .So I need to you help & your good suggestion &good way .please.
Thanks.

but the prices expensive or no. can u give me the model no ,please? but i think the my psu now i'm using is no problem & today i go back i need try POWERMAx to low level format my hdd, see how
But last time i have this psu problem (using pentium MMX with many blower fan with one PSU only),during booting,the HDD can't detect ,but now can detect HDD at booting,then system hang on windows,after restart can't detect HDD,very funny

Help...KT3-Ultra2 and Hard drive problems

Hello, I'm new to this board. I've been having an issue with hard drives lately. I have an MSI KT3-ultra2 with the latest BIOS version installed. I recently had a hard drive get completely erased and the actually size of it (10gig) had changed to 1 gig. Just prior to that I got a corrupted file error in a game I was playing. (The 10gig HD was a storage drive). My main drive (Maxtor 40gig) started to clunk and whine and then eventually the computer would lock up hard. I assumed the HD was going bad and was the cause of all the corruption. So I went and bought a new WD Hard drive 80 gig. Had it for about 2 weeks now and now all of a sudden I'm getting a similar clicking noise and a whine and then it locks up on me. I can only run my computer for about 10 to 20 minutes before it locks up. I have changed IDE cables to see if they were the cause and that didn't solve the problem. I've also disconnected all my CD drives and still nothing. I am going to take a guess and assume there is something wrong with my MB. IDE controler perhaps? Can anyone help me with this or confirm my thoughts on the situation? Any help is greatly appreciated. Thanks

May be your powersupply is faulty. Or the memory? try to get it checked

Kt3 ultra2 + MSI 8348A CD/RW problem

Similar Messages

Maybe you are looking for