KT3V Troubleshoot This
I've got a KT3V with a 450Wps, AMD processor, 256k Kbyte Ram (purchased from Office Depot) Adaptec 2940uw SCSI, 9g Cheetah HD, HP tapedrive backup. Maxtor IDE 40g hard drive and CD-RW running Windows 2000.
From time to time this machine freezes. After such a freeze up and a reboot the SCSI utility doesn't see the 9gb Seagate SCSI hard drive on the boot up menu, only the tape drive back up shows and thus NTLDR can't be found. If I turn the machine off for 15 -20 minutes the hard drive shows up and the machine boots. If I don't let it sit the 9gb boot drive never shows and the SCSI utility.
Can I assume that since the machine does boot most of the time from the SCSI hard drive that the SCSI set up is ok? Could a problem with the hard drive instead of the controller cause this problem? Could cheap ram cause it?
Ideas and suggestions are welcome.
Michael
Hi..
You might have some sort of a heating problem... This would explain the hard disk detecting problem u seemed to plagued with... Either your haard disk or the SCSI card might be overheating (Ill bet my money on the HDD).. If might be worth it to install a HDD cooler... And how is the status of the cooling inside the casing... Try to arrange the cables so that there will be some air flow into the hard drive
Best of luck
Rasika
Similar Messages
-
Hi all,
I need help with my iphone4s.
When I turn on my iphone4s, the apple logo will show for a few seconds, and it will suddenly fade off to a blank screen, and not start up. It will then restart by itself, and the cycle repeats. Any suggestions on how I can troubleshoot this problem?
What seems to be the problem here?
thanks and regards
WanWanlucg wrote:
When I turn on my iphone4s, the apple logo will show for a few seconds, and it will suddenly fade off to a blank screen, and not start up. It will then restart by itself, and the cycle repeats.
Make sure you have the Current Version of iTunes Installed on your computer
iTunes free download from www.itunes.com/download
Then See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once... Be sure to Follow ALL the Steps...
Take your time... Pay particular attention to Steps 3 and 4.
After you have Recovered your Device...
Re-Sync your Content or Restore from the most recent Backup...
Restore from Backup > http://support.apple.com/kb/ht1766 -
My wireless keyboard disconnects and reconnects within seconds but all text that was typed during the time offline is missing. i have to go back and retype missing parts. What can I do to troubleshoot this. The computer is only about six month old. This problem is new in the last couple weeks. Thanks for suggestions.
Beat me to it, Donald. But there is a possible alternative. If the batteries have been replaced since new, were they replaced with the same batteries or another make. There are examples around which do not fit perfectly and leave a certain amount of movement inside the battery housing. That could lead to instability such as the OP describes.
-
when i send an email in greek characters the receiver gets only question marks. how can i troubleshoot this?
Microsoft has finally addressed this issue!
You need to download and install the 14.2.4 update (110MB) for Office 2011 from here: http://www.microsoft.com/en-us/download/details.aspx?id=34690
Unfortunately, if you have been lazy with updating you will also need to download:
Service Pack 1 (14.1.0), 247MB: http://www.microsoft.com/en-us/download/details.aspx?id=17198
[Service Pack 2 (14.2.0), 110MB: http://www.microsoft.com/en-us/download/details.aspx?id=29419 -> you don't have to download this]
Update 14.2.3, 110MB: http://www.microsoft.com/en-us/download/details.aspx?id=30214
These are all pre-required...
This update adds the ability to select a default text encoding for composing new messages.The encoding that is selected in composing preferences will be applied to all new messages that are sent from Mac Outlook. To access composing preferences, select Outlook, select Preferences, and then select Composing. The new preference is Preferred encoding for new messages. (From: http://support.microsoft.com/kb/2742588/en-us?fr=1 ) -
FaceTime freezes when I call my son's iPad. Calling his iPhone in the same room has no problems. The picture is high resolution. There are no freezes when calling my daughter's iPad but the picture is lower resolution. Can I troubleshoot this?
Thanks Mario, but I tried everything there before posting my question. I may not have been clear in my question since I accidently recorded the whole question as the title and tried to edit. In brief: I have no trouble connecting with my daughter's iPad or my son's iPhone. However, his iPad is sending much higher resolution pictures and we disconnect after about a minute. Oddly, he can hear and see me while my screen first freezes, then goes black and gives me a message of "reconnecting" until it quits trying and shows the buttons to end or redial. The picture quality difference is what is leading me to believe it is bandwidth related. However, I get anywhere from 5 to 10 MB download speeds; usually closer to 10. Last summer, I had 4 granddaughters on their iPads, a grandson on his gaming device and me on cell phone or pc, all using the bandwidth at once with no complaints. If there is a way to lower his outgoing resolution, I think that would help.
-
Here is what happened.
I had a fully functioning masterpage
I copy the 'html' masterpage by using 'copy and paste'
When I preview this masterpage, this is what I see:
It looks as though somehow all of the styling has been stripped out. The content for the most part is still there.
I tried:
relinking the stylesheets and still having a problem
Can anyone suggest how to troubleshoot this? Could it possibly be an ASP.NET conflict? I know that on any given masterpage a webpart ID cannot be duplicated and generally other IDs should also not be duplicated.Hi,
According to your post, my understanding is that you had an issue about the Master page.
What did you mean “copy the ‘html’ master page by using ‘copy and paste’”?
Did you mean you copy and paste the html master page in SharePoint Designer?
If so, you can preview the default html master to check whether it works.
Then you can copy a new html master page, then write your own function step by step to check whether it works.
Thanks & Regards,
Jason
Jason Guo
TechNet Community Support -
I m having problems with both my iphone 3gs and 4 when my cellular data is on and my battery is fully charge but out of suddenn it will shut off can i know how can i troubleshoot this issue thanks
simply try doing a back up and restore
when going thru the activation screen, select SET UP AS NEW and then test your device. if it is not shutting down then it could be 1 or more apps tht have been downloaded wch could be affecting the device
you will then need to follow the process of eleimnation, meaning add 2 apps and then monitor your phone, if nothing happes then add another couple of them and then check
good luck !! -
Messages from one of my contacts shows up on my iPhone but not on my iPad. I don't have similar problems with any of my other contacts. Any ideas on how to troubleshoot this?
Does your iPhone and iPad use the same address for Messages?
Using FaceTime http://support.apple.com/kb/ht4319
Troubleshooting FaceTime http://support.apple.com/kb/TS3367
The Complete Guide to FaceTime + iMessage: Setup, Use, and Troubleshooting
http://tinyurl.com/a7odey8
Troubleshooting FaceTime and iMessage activation
http://support.apple.com/kb/TS4268
iOS: FaceTime is 'Unable to verify email because it is in use'
http://support.apple.com/kb/TS3510
Using FaceTime and iMessage behind a firewall
http://support.apple.com/kb/HT4245
iOS: About Messages
http://support.apple.com/kb/HT3529
Set up iMessage
http://www.apple.com/ca/ios/messages/
iOS 6 and OS X Mountain Lion: Link your phone number and Apple ID for use with FaceTime and iMessage
http://support.apple.com/kb/HT5538
How to Set Up & Use iMessage on iPhone, iPad, & iPod touch with iOS
http://osxdaily.com/2011/10/18/set-up-imessage-on-iphone-ipad-ipod-touch-with-io s-5/
Troubleshooting Messages
http://support.apple.com/kb/TS2755
Troubleshooting iMessage Issues: Some Useful Tips You Should Try
http://www.igeeksblog.com/troubleshooting-imessage-issues/
Setting Up Multiple iOS Devices for iMessage and Facetime
http://macmost.com/setting-up-multiple-ios-devices-for-messages-and-facetime.htm l
FaceTime and iMessage not accepting Apple ID password
http://www.ilounge.com/index.php/articles/comments/facetime-and-imessage-not-acc epting-apple-id-password/
Fix Can’t Sign Into FaceTime or iMessage iOS 7
http://ipadtutr.com/fix-login-facetime-imessage-ios-7/
FaceTime, Game Center, Messages: Troubleshooting sign in issues
http://support.apple.com/kb/TS3970
Unable to use FaceTime and iMessage with my apple ID
https://discussions.apple.com/thread/4649373?tstart=90
How to Block Someone on FaceTime
http://www.ehow.com/how_10033185_block-someone-facetime.html
My Facetime Doesn't Ring
https://discussions.apple.com/message/19087457
Send an iMessage as a Text Message Instead with a Quick Tap & Hold
http://osxdaily.com/2012/11/18/send-imessage-as-text-message/
To send messages to non-Apple devices, check out the TextFree app https://itunes.apple.com/us/app/text-free-textfree-sms-real/id399355755?mt=8
How to Send SMS from iPad
http://www.iskysoft.com/apple-ipad/send-sms-from-ipad.html
You can check the status of the FaceTime/iMessage servers at this link.
http://www.apple.com/support/systemstatus/
Cheers, Tom -
I have been using safari on a pretty old Dell with Windows XP. I use it mainly to access email on google. Suddenly I cannot get into my emails and there
are no error messages. How should I troubleshoot this problem? Also, safari is an older version - should I upgrade it?Safari for Windows was discontinued a long time ago. It has bugs that will never be fixed, and it should no longer be used.
-
Hi. I can't get the flash on my iPhone 5 to work. Does anyone have any ideas on how to troubleshoot this. Any help would be appreciated. Thanks.
Tap Camera App > switch to video > see if the flash will turn ON. If still problem, Restore your iPhone with iTunes on computer. See if fixed. If still problem, your iPhone has full Warranty with Apple.
-
my mac will not send or receive email's... its not internet connection... my iPhone still receives emails... so I'm not sure how to troubleshoot this problem, any ideas?
What does the Mail Connection Doctor return?
The link in my first replay included :
If you still can’t send or receive email
Mail Connection Doctor may be able to tell you more about the issue. -
Whenever I send a email from iPad mail app with an attachment from pages or numbers, the receiver is getting only attachment in the email. They are getting the email content. How to troubleshoot this issue.
Someone is probably sending spam with your address forged on the To: line. Could be one of your old contacts with a Windows machine has a virus that's doing it. It's also possible your e-mail account has been hacked, though I'd think such a hacker would be a bit more purposeful.
For more information, see:
http://www.reedcorner.net/guides/macvirus/is_it_malware.php#spam
* Disclaimer: links to my pages may give me compensation, and should not be taken as endorsement of my services by Apple. -
My Mac pro tower has an "ATI Radion hd 2600 XT" video card, and it stopped getting signal to my tv, are there common problems known? How can I troubleshoot this problem when the signal isn't reaching the screen?
http://discussions.info.apple.com/thread.jspa?messageID=12248238�
http://discussions.apple.com/thread.jspa?threadID=2649035&tstart=0 -
This is the second time I've encountered this issue with Time Capsule using Time Machine automatic backup. I haven't found the following specific error message in the list of troubleshooting issues: "Time Capsule cannot complete the backup. The backup disk image “/Volumes/Data/MacBook Pro.sparsebundle” is already in use."
I'm not certain what causes this issue. I think it may have something to do with having to force shutdown with apps still open when the beachball hangs and the MacBook has to be rebooted.
Has anyone else dealt with this issue?Welcome to Apple Support Communities
Restart your Mac and the Time Capsule. In most of the cases, this should solve the problem.
If it doesn't work, see > http://pondini.org/TM/C12.html -
How can I troubleshoot my iphone5 if it got stocked searching for my carrie?. I already tried removing the SIM card but it doesnt stop searching. I also tried using other SIM but still same result.
Try this: press F10 or tap the Alt key to display the menu bar temporarily, then
View > Toolbars > Menu Bar
If that doesn't work, you could reset your toolbars to factory default using Firefox's Safe Mode. First, make a backup of your computer for safekeeping. To back up Firefox, see [https://support.mozilla.com/en-US/kb/Backing+up+your+information Backing up your information].
Next, start Firefox in Firefox
[http://support.mozilla.com/kb/Safe+Mode Safe Mode], and check only the box to reset toolbars. Be careful not to "reset" anything else if you didn't back up.
Hope this helps.
Maybe you are looking for
-
Direct Posting to g/l accounts
Dear all, Client is buying a material, with material master having Qty and value update locally through petty cash. They donu2019t want do PO and GR. They want to settle it directly in MIRO. But they need qty and value updation. Is it possible ? how
-
Hi all I have created two iveiws KMNavigation iview web dynpro iview I want to assign these iviews to folder which is present in a workset How to do that thanks in advance
-
The keypad does not come up while adding new phone number to contact
I use iphone4. After I upgraded to ios7 finding lot sof issues. The biggest irritating issue is if I want to add a new number (after dialing this number or receiving a call from this number or receiving a sms from this number) and press add to contac
-
I can't open firefox w/o restarting my computer. How can I fix this?
When I try to open firefox, a screen appears that says firefox is still running and I must restart my computer. I closed firefox, but the screen still appears.
-
Weblogic.appc without kodoc
I have a EJB module with an EclipseLink persistence unit (<provider>org.eclipse.persistence.jpa.PersistenceProvider</provider>). When weblogic.appc is run on this EJB module, Kodo Enhancer is also run on the persistent entities. This happens with bot