KT4 Ultra bios update?

Does the new 1.2 bios allow you to unlock cpu's mutiplier ? if it don't will msi ever support it ?

Just go to a hobby (perferably somewhere taht deals with model trains) and get some silver nitrate varnish!! it's about 8 bucks and its just conductive nail polish!! igot it used a toothpick and unlocked my ship and if something goes wrong it rubs of with alchohol very easily!! Also make sure you fill the pits in with either crayon wax of epoxy !! :D good luck!

Similar Messages

  • KT4 Ultra BIOS Update soon?

    Has anyone got any info about the intended release date of the next BIOS update for the KT4 Ultra 6590? It seems the KT4V is getting a load of updates....

    obviously not - lol

  • KT4 Ultra FISR Updated Bios Still Reboots

    I bought a KT4 Ultra last week.  I hooked up everything needed to install my OS (Video and Hard Drive) to install Windows 2000.  It took me a while to get a good install because it would crash in the middle of Win2K setup.  After reading the posts on the subject I upgraded the Bios to 1.3.  I no longer had problems with installing software of transferring large files between CD and HD.  Although a bit slow, it worked.  
    But now I have another problem.   The computer reboots when the CPU is being used hard, like running 3D intensive software.  For example I have 3D studio rendering and then I try to open Internet explorer and computer will reboot.
    I check my PSU by measuring the voltage (with DMM) on the 5 volt line and causing a reboot during CPU intensive activities.  I even unplugged an extra HD and ran my FSB at 100 mhz.  I did not notice any voltage drop and the computer still rebooted.
    I need to decide to if I want to return the MB, before I go out a buy a PSU and find out it did not fix my problem.
    Any ideas.

    Video Card is a
    Video: Compro GeForce3 Ti 200
    HD: Maxtor 30GB 7200 RPM ATA100
    Power Supply (don't know brand name)
    300W, with 150W for both the 3.3 and 5 Volts (at
    least according to the label)
    The computer also rebooted while trying to run
    Nero to copy a CD image to hard drive.  So I don't think its video card related.  I had this video card in my ABIT KT7 with no problems.
    M.

  • Kt4 ultra bios

    have a strange paradox regarding disturbing message at boot up.
    when i boot my system i recieve a message:
    "no drive attached to fast track controller.  no bios detected.."
    i love msi boards and have used this forum in past very sucessfully with the assistance of BAS.
    I donated my old system to a freind in need.  It was all of 11 months old and was a very stable system built on a k7t pro 2-ru.  It had all the bells and whistles.  what a mistake.
    my new system is as follows:
    kt4 ultra fisr
    256 mb ddr3200 samsung  (as recommended by msi)
    m-audio revolution 7.1
    ati all in one wonder radeon 8500 64mb
    2-80gb western digital special edition hard drives  
    dvd/cd combo lg electronics  gcc-4320b
    athalon xp 2200
    550 watt antec tru-power psu
    lian li case with 4 fans (of which only 3 work with the power supply while allowing fan monitoring)
    klipsch pro-media 5.1 speakers
    winxp pro
    how i got there to the afore mentioned msge regarding controller and no bios detected...
    I was experiencing a lot of problems with the new set up
    such as:
    1.  system crashes while viewing tv
    2.  unexplained boot up of system in the middle of the    
         night (that was freaky and kind of humorous)
    3.  other system reboots and difficulty of system    
         shutdown
    4.  device driver failure messages regarding the ati card
         such as "atimmc.exe  driver failure"
    all system crashes revolved around the ati card and after recoveries many registeries were messed with as expected.
    all in all I got by with the system as long as i remained off applications involving the radeon card.
    last week I checked into the forum here and noticed issues with this motherboard and radeon cards.
    i went to the ati site noticed updated drivers, and at the msi site, updated bios for the kt4 ultra boards.
    i did not have a floppy so i backed off flashing the new bios onto the board.  I currently have the first version (1.00 or something), the screen flashes so briefly these days.
    i decided to reformat the drives and reload xp onto the new system and then retreive the newer drivers for ati card.  upon installation while reading my neurophysiology book upon boot up is when xp informed me that no bios was detected.   xp asked me if i wanted to continue.  so i did continue with sucessfull installation of xp.
    being quite surprised that i could still get system on board, i am wondering how to get the bios to be detected and if I should try and flash new bios, if this will correct this.  I am also with fresh install of xp having no difficulties shutting down system now and i am no longer having mystery unassisted boots of the system.
    all in all, before the bios problem i was just wondering about the stability of the board with the ati radeon card.
    Now I am very concerned with the message, "no driver attached to fast track controller... no bois detected"
    any words of wisdom would be greatly appreciated.
    Boy, do i miss that k7t board...
    thank you,
    Eric  

    Do NOT worry about the fasttrack controller message!!
    It just says you don't have any serial-ATA disk attached. This is how to get rid of the message:
    In BIOS:
    => Integrated Peripherals
    => OnBoard PCI Controller
    => Serial ATA ---> set this to "Disabled"
    Can't say I experience any of your other problems, although I had some problems with the sound card the first time I installed.
    Seems as if the problems are fewer the more times you install/format the system.....actually experienced that on a couple of MSI-cards. In the end, everything has worked fine for me, so I'm happy with them (except design and layout of the new nForce K7N2G-cards!! ridiculous!)

  • Kt4 ultra bios 1.3 ati problem

    I updated my bios a while ago and when i did i noticed pixels in weird places.  I updated from 1.2 i was having problems with crc errors, after that i couldnt run any driver verision on my ati 8500le above 2.5  so i couldnt run 3.0a 3.1. i was just checking if anyone else had these problems when updating to 1.3 on there kt4 ultra. and i flahed twice the first time i thought it was a bad flash or something. i was running 3.0 and downgraded. i am hoping msi will fix this issue but who knows. overclocked or under clocked i still have the problem.
    i am running 2.13GHz overclocked from 1.73
    kt4ultra
    768 ddr400 running at 333MHz
    ati 8500le

    I've done that, but the problem still exist.
    I think it's more like a BIOS problem since there's no problem when I'm runnign 1.1 instead of 1.3

  • KT4 Ultra Bios 1.2 Doesnt Work

    I have just updated my Bios to verison 1.2 and the computer wont go into windows.
    Infact I have found the problem to be the USB Via chipset thats at fault. I have Windows Me and the the computer freezes every time it tries to load USB.
    I have put version 1.1 back on an no problems.
    I have reloaded windows and  the following error appears.
    Windows has had to disable the USB function due to a internal problem.
    I try to reload the drivers and it freezes.
    I have just spent 8 hours to find the problem was the usb chipset.
    Does anyone else have the problem ??
    Thanks

    I am running a KT4 Ultra with XP2000 Cpu. I updated my bios from 1.1 to 1.2 over the weekend, and now my once stable system is giving me no end of problems.
    1, It would not recognise my primary hard drive and I had to clear the bios with the jumper four time before it would let me boot up.
    2, Once I booted up and ran 3dmark, it was okay the first time but the second time the machine crashed and totally corrupted my hard drive. I had to reformat my hard drive and load a backup (two weeks old).
    3, I have now re-flashed my bios back to 1.1 but although the system is working I keep getting CRC errors when trying to backup my hard drive to my secondary drive. This did not happen before.
    This 1.2 bios seems more like a rushed beta version than a real bios update, it has given me loads of problems and I now have a system which is still not working properly.  Bios upgrades are supposed to fix problems not create them!!
    I would NOT touch this 1.2 with a long barge pole !!!

  • KT4 Ultra Bios 1.4 fixed?

    There was an issue with the 1.4 bios update for the KT4 Ultra chipset and the temperature reading. I was misreading the temperature. Does anyone know if this issue has been fixed? I contacted MSI about it several times but haven't heard anything back.

    Nope,still the same dated one as before.
    Also when I installed v1.4 it sent Windows XP settings nuts with the HLT command enabled in bios.
    So no matter if anyone says the bios is fixed,it aint yet.
    There will be a different date on it anyway.

  • K9N Ultra BIOS update

    Hi. I have K9N Ultra. I had Sempron 2800+ installed on it, and everything worked fine. Now I'd like to install Athlon64 X2 5600. BIOS POST said that it doesn't know processor's revision and won't work at all. I downloaded new BIOS from http://global.msi.com.tw/index.php?func=downloaddetail&type=bios&maincat_no=1&prod_no=253 (7250v3A.zip). Unpacked and copied Afud408.exe and A7250NMS.3A0 to disk C:\. Then I booted from win98 boot floppy and did the following actions:
    > c:\
    > Afud408.exe A7250NMS.3A0
    BIOS update was successful, I turned off the computer, cleared CMOS with SW2 button and installed new Athlon64 X2 5600 CPU. Then I booted again.
    The problem is that my system works unstable now. It may suddenly turn off in Windows when I play games. In Linux it may suddenly turn off when I use microphone in Skype.
    Motherboard's version as it written on the board between PCI slots: MS-7250 Ver: 2.1.
    How to fix it? Thanks!

    Quote from: BOSSKILLER on 16-January-09, 20:43:36
    Read >>Posting Guide<<
    Reseat the CPU and make sure CPU heatsink is mounted properly and no overheating issue occur.
    It is not overheated, because my system turns off immediately after test call in Skype (in Debian Linux). I can compile software for hours, using 100% of both CPU cores, and my system works stable, so I can conclude that it is not overheated.
    I have 2x1GB Kingston DDR2-800, GeForce 7600GS PCI-E, 2x250 GB SATA Seagate drives, Athlon 64 X2 5600 (AM2).

  • Kt4 ultra bios and raid function

    i am using the kt4 ultra motherboard (bluetooth ready and SATA), when i go to the integrated peripherals, onboard pci controller i can only enable/disable the audio controller....
    where am i supposed to enable/disable the raid controller?? is there a jumper i am missing on the board?
    thanks in advance,
    brian

    Are you sure you have a KT4 ultra with the Serial ATA/RAID controller option? There are several versions of the motherboard, all doesn't include the PDC20376 SATA/RAID controller, please check if you can find the chip on your mobo. The controller is enabled/disabled under Integrated Peripherals->OnBoard PCI Controller
    ->Serial ATA controller.

  • KTA Ultra BIOS Update

    moderating gentleman and friends with experience
    When it wants to do a BIOS Update I must do it with completes version 1,3 ??
    This completes version fixes the problems that fixed the previous versions or I must install all updates that they have published??(1.1 + 1.2 + 1.3)
    By I complete, if my equipment this working well I must make BIOS Update?
    Thanks

    only update for fixes you need
    if not having crc errors with large files leave it be
    you only need update to one you want
    no need to flash 1,2 3 etc

  • KT4 Ultra BIOS 1.4 Released

    I've not tested it yet but here it is.
    http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=356&NAME=MS-6590

    I updated to 1.4. As always the update went off with out a hitch. I reconfigured all my bios settings after the new flash and everything seemed to be as it should be. When I got into windows (2000 SP3) I looked at my PC Alert4 Temps, they were incredible. 27C for CPU and around 30 for System. I was looking at the temps while benchmarking on PCMark 2002 so I closed the prog and right before my eyes the temps plumited and settled into 24C. that was 6 less than system. I'm air cooled and O/C by over 500 mhz so this is not possible. I rebooted thinking it was a glitch and when I got into the bios I looked at the CPU and the system temps and they were the same, at 30C. a little better but still not belivable. Before the flash I had system temps of mid 30s and CPU temps of around 39 or 40. Beware of this update, especially if you already have heat issues.

  • MSI K9N SLI/K9N ULTRA bios update

    Hello everyone,
    I want to install windows 7 on my Pc but during the installation my PC stucks and do nothing.
    I have already tried a lot of things but nothing happened.The same thing again.
    Finaly I think that I need to update my BIOS version because I have not do it before.(since 2006 when I bought my PC)
    Probably I should do it from a bootable CD because my motherboard can not boot from a usb stick and also I don't have a flopy Drive.
    Is there any official tutorial (maybe from MSI) to do it?
    Do you have anything else to propose???
    Thank you in advance!!!

    >>Posting Guide<<

  • Mobo MSI KT4 Ultra, bios 1.30

     ?( Is this possible, if i connect two disks(master and slave) to ide3(raid)
    slot and CDRW to ide1 slot, master(udma). Boot from master disk and reinstall windows xp
    and Promise raid driver, so on......??!!
    Disks are Seagate Barracuda IV 60Gb(identical). And is raid-0 any faster than typical ide100? Do i have to setup raid-1 if i wanna more speed(seektime etc)?
    How to setup arroy?
    And what is raid bios? What is newest and how to upgrade....?

    In the beginning it is difficult. Take it slow. You can work out yourself by using the web as the medium to provide you more information about RAID. There are plenty of search engines to help you.
    Here is one article you can read: http://www.anandtech.com/storage/showdoc.html?i=1491 It is not idiot proof kind of article though. You need basic knowledge about storage devices.
    There is a guide here to be able to help you. But DO NOT ATTEMPT if you don't understand it.
    http://www.msi.com.tw/program/e_service/forum/viewindex.php?threadid=292&boardid=16&styleid=1

  • Kt4 ultra BIOS pc health freezes

    The title about says it all. Whenever I try to view the PC health menu in the BIOS the computer freezes needing a retstart as you cant move off the PC health menu - the arrow keys don't work. It happens immediatly on pressing enter when on this menu and I can get into all the other menu options without any problem.
    It never used to do this maybe putting 1.4 bios on will put it right?
    Has anybody seen this issue?

    Set the timmings for the RAM and CPU to the lowest performance. (the FSB, latency, 1T command off, priority, quick boot off)
      If this does not work, you must flash the bios - use the CTRL+HOME mode with the bios file named amiboot.rom on a floppy.
       Usualy this is a RAM issue, happening when you overclock. Try also replacing it.

  • Overclocking KT4-Ultra & BIOS 1.4

    Hy. I've overclocked my 2400+ to 2300Mhz(170FSB). I had also to upper the core voltage to 1.75v (1.74real) so because of this I get higher temps. The thing is that I use a RaptorCool silent cooler and a 12cm fan blowing cold air into the case. This is obvious not enought but is silent. And I use the PC mostly for "domestic" things like watching movies and listening music and just ocasionally for games. Now I would really need the CPU Halt Command enabled in bios to lower my temperatures, but this is available only in v1.4. And if I flash to 1.4 I loose my preseted 13.5 multiplyer (wire trick) that is changing into 11 there goes my overclock.  The WPCREDIT method does not apply as I want to switch easy from Enabled/Disabled by just selecting in bios.
        How could this be even possible? If this can happen (multiplyer from 13.5 to 11) why not also a bios to unlock the CPU?

    The issue here is not why I want to overclock (doh) and also not the HDD performance. And I am among the users that flashed a lot the mobo and  that reported the v1.4 temps issue wich is not solved and I think it will never be as the support stopped. I needed the CPU Halt because was a simple ON/OFF thing. Now I find it was   because I would still need to enter the bios. So why not just lower the voltage?    But yet is this strange thing - how can the multiplyer change from 13.5 to 11?  This v1.4 bios is full of (unpleasent) surprises.  
        Anyone played the flash game Bubble Trouble? Well, that's a game that requires a lot of CPU. Even with Radeon9800 you will be in "trouble" if you don't have enought CPU )) And this is the main reason why I overclocked ) to play it while I run a movie on TV-out and listen to music on my usb earphones.

Maybe you are looking for