KT4 Ultra crash on boot

Can anyone help please
System crashes at boot
using
AMD Athlon XP 2400
512MB DDR / PC2700
MSI KT4
But sysem runs fine with old AMD 900 chip

Quote
Originally posted by wonkanoby
d bracket lights stop were
psu combined watts and amp details of its label
d bracket lights all red
ac input 115/230VAC 8A/4A 50/60Hz
AC OUTPUT 115/230 VAC 1A/0.5A 50/60Hz
DC OUTPUT +3.3V +5V +12V -5V -12V +5VSB
14A 30A 15A 0.5A 0.8A 2A
165W max 9.6W max
350W
Thanks

Similar Messages

KT4 Ultra crashing/rebooting problems

Hi all, I've been having computer crashing/rebooting problems when I play 3d games since I got this board. It can happen between 1-40 minutes during a game session and when the computer crashes, the screen would garble up and reboot along with the garbled screen until I cold boot it. I thought it was a heat problem at first but the cpu heat displays at between 34C-39C. Also, when I tried switching out the video card with an older one, the computer works fine during gameplay, and my newer video card ran fine on a friend's computer. Does anyone know of a way to fix this?
System specs are:
Motherboard: MSI KT4 Ultra
CPU: AMD AthlonXP 2400
Power: 300watt
Ram: PC 2700 333mhz DDR 256MB
Video: Gainward Geforce4 Ti4200 Power Pack Plus! Ultra 650 64MB
Sound: Onboard
Thanks

by the sound of it try a bigger psu,antec enermax over 400 watts
make sure fan on cards not loose

New KT4 Ultra Won't boot

Still looking for an answer to my boot up problem. Computer starts and the lights on the dbracket stop at the first green light. I get no video,keyboard or mouse and I have to use the power supply switch to turn it off. I assembled the board with no problems. Rule out the stupid stuff like plugging stuff in with power on the board or misinstalling the cooling fan. I followed the instructions carefully. Did I break this thing, or should I buy a new power supply X( and try again? It would have been nice if the manual said something about the power supply so I could have planned that into my system. I really thought 300 watts was enough... it worked fine on my Shuttle system. If you have a recommended power supply in the $30-40 range, please let me know the make/model so I can go shopping.
I would greatly appreciate any help that will keep me from having to spend hours on the phone with the MSI Tech Support help desk.
KT4 Ultra MS 6590, Athlon 2200+, Kingston 512M 333 PC2700; 2 EIDE 7200 RPM HDD's running Win 2K Prof;2 EIDE CDROM's; Nvidia Riva TNT M64;Realtek PCI 10/100 Lan (RJ45) Antec Model PP 303x 300W PSU(3.3/14A;5/30A;12/10A Peak 160W)

I had this problem when I first got my KT4 Ultra and it was either one of two things I did and it works fine now.
Make sure that you don't have more of those spacers that seperates your MB from your case. There should only be like 6 that you need to put on. Any more than what you have screw holes for up top and you're potentially shorting out the board to the case. Luckily I didn't cause any damage and as soon as I put only the necessary spacers in, I had full boot up.
Another possibility is that your jumper pin that is used to clear the CMOS is in the wrong position. I contacted MSI tech support before and pointed out that what was shown in the diagram as the correct jumper position was different than what is said in the instructions. This caused me some confusion and luckily again, it didn't cause any damage.
Hopefully someone else will chime in on my response to your problem and either back me up or disprove it but it couldn't hurt to double check those things I've pointed out.

KT4 Ultra won't boot if I change settings in BIOS

I can't change any cmos settings either. If I change anything in the bios at all it won't boot. it will turn on but won't boot. so I have to clear the cmos to get into windows and my 2500+ Barton is running at 1050mhz because I can't set the fsb to 166(333) like I should be able to. And I just bought the chip yesterday.
KT4 Ultra
Athlon XP 2500+ 333FSB
Samsung 512MB DDR333
Radeon 9800 Pro
Antec Sonata case with 380Watt Truepower PS

jebradec41
Well, its not yet conclusive that your BIOS is bad, all we are saying at this stage is that with a new CPU, you can change settings but it will not Boot. Correct?
When you update a BIOS you only do not always change all the data stored in the memory.
I have, before now, resorted to to using the emergency recovery feature of the BIOS that is well documented.
This way, subject to the memory not having any bad addresses, you completely re-program the BIOS I.C.
Have you tried BIGRHINO suggestion first?
Kind Regards

KT4 Ultra reboot before booting

Ok, this is going to be long, but I'm hoping one of the details will give somebody a clue. I'm going to stick in details I don't think are relevant even.
The components relevent to this story:
KT4 Ultra Motherboard
Addtronics 300W power supply
Athlon XP 2400+ cpu
Windows XP SP1
2 seagate 120gig SATA drive in a mirrored RAID config
A cheap off brand UPS.
This machine had been up and running about 9-10 months on the current install. The machine was ROCK solid. I ran this machine 24/7 with reboots only for getting rid of adware or stuff like that. Never did I see a blue screen or any bad behaivor. And I never even bothered to cycle the power during this time. Sounds good right?
Well I'm doing some work on the carpeting in my office, so I shut it down and moved the machine to a different room. Well I got everything plugged in and powered it up, and to my surprise it started doing a chkdsk (the in boot chkdsk) since it wanted to, I let it go. Well as I watched I could see tons of errors coming as I'm watching this many of the files where clusters were being repaired were in the Windows/system32 directory. So I'm thinking to myself I'm screwed (which is true), as I see the names of vital system files going by.
So after completion it automatically reboots (chkdsk forced it), so I get to the screen where the login should be, but no press ctrl alt del to begin message but instead I get a box saying a service (lssas i think) specified invalid parameters. I click ok, and I having nothing but a solid blue screen. I press ctrl alt del and nothing, so I reboot again. This time I get the same error, but I also get the ctrl alt del to begin message, and I press, I then enter my login message. It does stuff for a second and then reboots.
So now I let it reboot again, and during the reboot it powers down. I was confused by this. I pressed the power switch, and I could see the power, hd leds blink for a sec and then blink off and the PS doesn't even start. So I press again a few times and get nothing. I leave it alone for awhile, come back and it powers up again. Same error, same login attempt, same power down.
I grab my laptop from the otherroom and plug it in to the same wall socket (directly not through the UPS) that my UPS is plugged into. At that instant, it goes in to power save mode (too quick to be normal power saving), so I quick unplug it, and plug it into the ups. As I plug it in, it it comes out of power save and operates normally (that's what I'm working with). So I'm thinking something is wrong with the power outlet (I will pursue that tomorrow), so I go and grab one of those indoor/outdoor orange heavy duty extension cords and plug everything into a different room, and all seems to be working fine.
So at this point i try my computer again, same thing. I decide its time to repair the winxp install, so I boot off of the XP cd and load the RAID drivers. Right at the screen where it says R to repair, something to install, something to exit, I choose repair, and it immediatly powers down. I did it again, and this time it powers down a second after this screen comes up.
So this is where I am now. I think I had bad power or something, and I now suspect that the PS or the motherboard might be bad. But since it really consisently powers down at the same point, im confused as to what the problem is.
Anybody have help to offer?

http://www.microsoft.com/security/incident/sasser.mspx
It may not be a virus but when you said Lsass
It may be the PSU.

KT4-ULTRA Doesn't boot!

Im having a strange problem with the kt4. It doesn't boot the first time i turn the computer on for the day. It starts up, all the fans etc. but nothing happens. If i hit the reset button, it will then start and give the options to start in safe mode etc.... After that, it will boot everytime from a cold boot. Any ideas why it would do this one time a day? Thanks for the help. d.

Hi StriFe,
Sounds like it might be a good idea to strip the system back to bare-bones and start again from scratch, very carefully and methodically. Make sure you observe good Anti-Static procedures before touching anything inside the case, etc.
Once everything is stripped out, reset the CMOS via the m'board Jumper and follow the instructions desribed in the m'board manual to avoid mishaps. Once this is done and the Jumper is returned to it's original position, you can start rebuilding the computer, one step at a time and checking for acceptable behaviour after each step by starting the computer and observe the D-Leds and the D-Led troubleshooting table.
By doing it this way, you will hopefully be able to identify the cause of the problem and then go from there. As a general rule, the BIOS settings should be left at their default settings until such time as everything is working properly. After that, if a bit of tweaking is on the agenda, do this on one thing at a time and at one step at a time, rebooting your computer after each single adjustment until such time as you achieve the level of tweaking you are after, or until the computer will no longer operate reliably, in which case you should revert back to a setting that is Two steps back from where you ended up. This should then give you sufficient margin of safety for the computer to run reliably.
Hope this helps. All the best
Dimal.

Kt4 ultra problem

hello! i am having a problem with my kt4 ultra.
it originally booted, but once i hit delete to go into setup everything crashed. now when i boot, i get 2 beeps followed by another 8 beeps.
i've done alot of browsing through these forums and other sites, and heres what i find over and over:
10 Short
CMOS register
Check the motherboard and remove all expansion cards and replace one at a time.
i've done this and there is still a problem. am i doing the wrong diagnostics for the 2-8 beep combo?

i cleared cmos by removing battery and via the jumper method. no go.
the cpu/mobo/ram/video/ethernet were in another computer and worked previously. i sold them to my friend and had him buy a new case - i got everything setup the first time, booted, hit del to go into bios to make sure all settings were correct. it crashed and now does the 2-8 combo beep.
previously the mobo was in another case and we used different ram, but i still get the 2-8 beep combo using that same ram.
spec are:
350w ps
kt4 ultra mobo
athlon xp 2200+
geforce 4 ti4600
1 gig ddr 300 ram
30 gig western digital 5400 rpm hd
philips cdrom
netgear ethernet card
+3.3 = 28A
+5 = 35A
+12 = 17A

KT4 Ultra & ATI 9700 & Black screen HELP

Hi guys,
After first uninstalling the Nvidia drivers and then powering down and removing the Geforce 4 card, I installed a brand new ATI 9700 that I got from Mwave.com for $199.00. When I turn on the power all I get is a black screen - I can't see anything on the screen but I can see my computer trying to post by watching the lights on the drives and observing the D-Bracket.
The D-Bracket is indicating a system hang on "Testing base memory from 240k to 640k and extending memory above 1MB using various patterns". Led's 1&3 red and 2&4 green.
I did hook up the 12 volt adapter that came with the the board at two different locations just to make sure there was not a problem with power. I also checked for the presence of voltage at the adapter right at the card with a volt meter (12.3 volts). I also swapped the power connector from the floppy to the video card. The cooling fan on the card is coming on. I made sure the power connector was connected prior to powering up my system. I also tried clearing NVRAM. What is wrong??? Any ideas out there? Do I have a bad card right out of the box ???
For now I had put my Geforce4 Ti 4200 back in so I can use my computer again.
My current system & settings:
Antec case, 400w P/S +3.3/28amps +5/40amps +12/18amps
WinXP Home Sp2. Dx9.0a
MSI KT4 Ultra biosv1.4 (boot) 4x AGP (there is no 8x option in bios)/ Fast Write disabled & enabled/ AGP Aperture size 64&128mb, AGP voltage set to AUTO. NOTHING IS OVERCLOCKED fsb 166, cas 2.5
AMD Barton 2500+
2-512m Corsair XMS3200
2-80 gig Maxtor Raid Strip 0
52xDVD
12x8x4 Burner
Linksys 10/100 ethernet card
Zoom 56k modem
4-80mm fans
My brand new 9700 card:
Model: OEM Generic MIC powered by ATI
Board revision: AO2
S/N:G0306025237
Memory: 128meg Infineon DDR SGRAM 3.3n
MajorDan

for one try removing one of your memory sticks,,try that first,,,make sure your fsb of the cpu and the memory are 166,,,,it will auto detect the 8x agp if the card suports it,,,,,,do you have the card setted all the wat,,,,,,,,,,double check memory settings,,this card i have found does not like fsb messed with or the memory fsb messed with.....set memory to spd,,,,good luck

KT4 ultra Beeps?

Hey guys, my friend has the same mobo as me, the MSI kt4 ultra, when he boots he gets no signal to the screen and the mobo beeps three times. anyone know what the three beeps mean? thx sasarchiver

i dont know much about your motherboard but if it got ami bios then this is what it means.
Quote
3 short
Base 64K memory failure A memory failure has occurred in the first 64K of RAM.
The RAM IC is probably bad
http://bioscentral.com/beepcodes/amibeep.htm

KT4 Ultra and XP2000 Crashes at 133fsb

My system runs fine at 100fsb with clock multiplier set to 12.5 giving me 1250 Mhz, but when I set my FSB 133 the system crashes. I've tried setting it with the fuzzy logic and in the bios. Each time it resulted in a black screen and I had to short the cmos to get it back.
Also How do you add the system info tag?
KT4 Ultra MS-6590
IBM 60 GB 7200 HD
AMD XP2000 model 6
Thermotake Heavyduty heatsink and fan
256 MB PC2700 Micron
GeForce4 440 64MB video card
L&C PSU Model LC-A350ATX
- 350 MAX
- +5 and +3.3 V Combined 190 watt

I have exactly the same problems here, system runs ok at 100fsb, but it isn't on 133.
I was thinking of a cooling problem already so this is clear to me now.
However one problem remains and that concerns the RAID option! Believe me or not, but currently this option is faded out in the BIOS (1.3) and therefore no bootable devices can be discovered also setting the option "Try other bootable devices" to YES does not work. If I start messings with the CMOS settings the RAID option might return after saving the adjustments and rebooting. While booting up the Fastrak376 is either present or gone.
Currently I have just a Matrox G400 MAX in the AGP slot and none of my PCI devices are used. Further two IDE devices (Maxtor 80gig DX740-L) are hooked up, one to SATA (with converter) and the other to PATA so it shouldn't be an IRQ issue.
I already cleared the CMOS using the jumpers and switching " on " the machine, did a NVRAM clearance and that didn't work either. Setting Plug and Play OS to DISABLED worked out once but after making some adjustments to the BIOS settings the RAID disappeared ever since ..
However I was able to install Windows XP once and as you probably can figure it took me two days getting the RAID option to work, apparently another BUG in the KT4? ?(
Unfortunately now I am stuck since no RAID for the time being ... Hope one can help since once again MSI does not respond to my emails... ... :O

KT4 Ultra MS-6590 - Win XP Home boots with 2GB DDR333 installed but not 3GB

Spec...
KT4 Ultra MS-6590
AMD Athlon XP 3000+ (FSB set to 166MHz in BIOS)
BIOS MS-6590v1.4
Win XP Home 2002, SP3
Problem...
Previously, had 768MB RAM installed, and XP strangely identified CPU as a 2200+.
Recently upgraded the RAM to 3GB DDR333 (3 sticks of 1GB 184-pin unbuff DIMM 128MX64 DDR PC2700), and changed BIOS settings for CPU and DRAM.
In the DOS boot screen, Win XP progress indicator fills completely from left to right, then stops with a half-blinking cursor in the top left of the screen.
Removed 1GB stick and Win XP successfully loaded, also now recognising the Athlon XP 3000+, and running a heck of a lot faster.
Tried adding the /3GB switch to the boot.ini file, which didn't do anything, and after reading more forum advice, guessed this might be irrelevant. I don't think this is a 4GT and PAE issue, as I'm not trying to install above 4GB (if I've correctly understood).
Also, forum advice (various sites) conflicts on whether Win XP 32-bit is limited to 2GB or 4GB, and I can't find any workarounds for my current setup.
Any ideas?

Another test I've done is to enable boot logging with Win XP. This appends command lines to the file 'ntbtlog' in the windows directory, which mainly shows drivers being loaded as Win XP is launched. The log is normally date and time-stamped for every boot-logging session.
When all 3 sticks are installed, I cold boot, then press F8 and select 'enable boot logging' from the options menu. This is what appears on the screen as the system, attempts to load Win XP.
Loaded driver \WINDOWS\system32\ntoskrnl.exe
Loaded driver \WINDOWS\system32\hal.dll
Loaded driver \WINDOWS\system32\KDCOM.DLL
Loaded driver \WINDOWS\system32\BOOTVID.dll
Loaded driver ACPI.sys
Loaded driver \WINDOWS\System32\DRIVERS\WMILIB.SYS
Loaded driver pci.sys
Loaded driver isapnp.sys
Loaded driver viaide.sys
Loaded driver \WINDOWS\System32\DRIVERS\PCIIDEX.SYS
Loaded driver MountMgr.sys
Loaded driver ftdisk.sys
Loaded driver PartMgr.sys
Loaded driver VolSnap.sys
Loaded driver atapi.sys
Loaded driver disk.sys
Loaded driver \WINDOWS\System32\DRIVERS\CLASSPNP.SYS
Loaded driver fltmgr.sys
Loaded driver sr.sys
Loaded driver PxHelp20.sys
Loaded driver KSecDD.sys
Loaded driver Ntfs.sys
Loaded driver NDIS.sys
Loaded driver Mup.sys
Loaded driver BTHidMgr.sys
Then the process freezes and a solid white block appears in the top-left of the screen, with the top-right corner of the block blinking.
At this point, I turn off the PC using the main power switch, then remove the 3rd memory stick. After booting up again, with only 2 sticks installed, opening the text file 'ntbtlog' reveals that this boot event wasn't logged.
So, I reboot Win XP with only the 2 sticks installed, and select 'enable boot logging'. This time, the above list of loaded drivers is shown in the text file, plus a whole lot more. The potentially interesting observation is the next in the list after "Loaded driver BTHidMgr.sys" which is "Loaded driver \SystemRoot\System32\DRIVERS\amdk7.sys".
'amdk7.sys' is a driver file which seems to come with one of the Win XP Service Packs, and which "is necessary to enable Windows XP support for AMD PowerNow! technology on computers that use a mobile Athlon 4 or mobile Duron processor." http://support.microsoft.com/kb/306458
Various other posts refer to it in relation to AMD Athlon XP 3000+ Mobile, whereas mine is a 3000+ in a desktop. Also, if 'amdk7.sys' isn't available, then Win XP will load the generic driver 'processr.sys'. In fact, my 'ntbtlog' includes the entry "Did not load driver \SystemRoot\System32\DRIVERS\processr.sys" which would make sense.
However, my curiosity is that with the 3 sticks installed, Win XP fails to continue loading when reaching 'amdk7.sys' in the driver list.
Another test I did was to change the power management settings in the BIOS.
"IPCA Function: This item is to activate the ACPI (Advanced Configuration and Power
Management Interface) function. If your operating system is ACPI-aware, such
as Windows 98SE/2000/ME, select Yes. Available options: Yes, No."
This was normally set to Yes. When I set it to No and rebooted with 3 sticks installed, instead of a half-blinking white block (as described above), the screen went black and then the system rebooted itself...
The plot thickens!...
Maybe there's a clear explanation for this - however, I'm wary of doing something to the 'amdk7.sys' driver file (whether removing or disabling it somehow) in case it prevents Win XP from launching with just my 2 sticks installed. I'd guess there are precautions, but need further info on whether this is relevant, and what the implications might be.

KT4 Ultra - SCSI boot problem

Hi,
I have installed a Tekram DC390U2W LVD SCSI adapter on my KT4 Ultra. My problem is that I cannot select any of the five connected SCSI disks as a boot device in the BIOS (BBS-n), nor can I select 'Legacy SCSI' as a boot device, they simply don't exist as options in the Boot Sequence menu. I've used this card (and were able to boot) without problem using a MSI KT266 motherboard, so I don't think the problem is the SCSI adapter. Any ideas would be appreciated.

I've disabled all motherboard options (Serial ATA Raid/1394/USB 2.0/GBLAN/Audio controllers), remove all PCI cards exept the Tekram card and tried it in all PCI slots without success. Also tried to assign different IRQs to the SCSI card in the BIOS. Tekram support responded that the SCSI card is fully PnP/BBS/PCI 2.1 specification compliant and they're unaware of any KT400 issues. There are issues (and work arounds) with this SCSI card when using it on motherboards with an on-board SCSI controller and older Award BIOS versions, but that's not applicable here.
Anyone out there using this SCSI card and motherboard got this combination to work as intended?

MSI KT4 Ultra based sys crashing/rebooting

Just Built a brand new machine with a KT4 Ultra, Athlon XP2000+, 512MB Corsair PC3200 Stick, ATi Radeon 8500 DV (64MB) card and a giant special edition hard drive from WD.
Love everything about the system - except it is clearly not functioning properly and I believe that I have isolated the problem down to the MOBO or problems associated there.
Problem is the system crashes in any taxing graphical situation. (Since I've only had it built for about 3-4 days, now, I only have a few fairly limited examples so bear wtih me.)
2-3 minutes into either Quake III or Unreal Tournament 2003 Screen goes black and system crashes - automatically rebooting. Problem also came up while trying to download latest AMD AGP sys file from AMD's site. (That is, so far, the only non-gaming example of this happening).
I have tried absolutely everything I can think of, and even a number of things that a savvy friend of mine could think of. Anyone else having this problem? Anyone got any ideas at all, here. Because this has got me totally frustrated.
Thanks,
Ben

Quote
Originally posted by wonkanoby
tried newest bios,claims fix for 8500
whats combined watts of your psu 3.3 and 5 v,asmps those 2 voltages as well
BIOS is still what came with the board. I have only seen that the first version of this BIOS is available. I have looked for updated versions but I only see 1.0. Is there another version of this BIOS available? I would certainly love to try if it does exist.

New MSI 6200 TD256 card in a KT4 Ultra (via) board,no boot, no page, help please

Hello.
just bought a new MSI Nvidia 6200 TD256 (http://www.newegg.com/Product/Product.asp?Item=N82E16814127186) and I put it in my KT4 Ultra board (via chipset). I am using the newest bios (1.4) and Via 4in1 chipset drivers.
What happens is when I boot the machine, everything starts up, but I get no PAGE and the D-Bracket is hung at the "testing VGA bios this will print ..." (thats what it says in the manual).
Now, I've done the best I can to research this issue, but best I can guess is this is a bad card and I should just return it for a replacement... the card does look fine, I see no physical damage and it seemed to be properly shipped. I did read that kt4 boards don't support 3.3v AGP cards... but I'm not really sure what that means.
Anyways, if anyone has any insight on something I should try before I have to go through the return process that would be much appreciated.
Thank you,
-Cody

Quote from: osnavi on 23-July-05, 09:34:35
And did you uninstall old V.card before installing new ?
if it doesnt get to windows, that doesnt matter.
Quote from: Cazzynomo on 25-July-05, 10:36:30
I'm using a good PSU 350w atm, and I did check it in another good system...turns out its a bad card.
ok then its clear its a bad card.

KT4 Ultra (MS-6590) very slow boot

i got a strange one here:
i replaced my MSI K7T Turbo2 with a KT4 Ultra. Since i got the new board installed (the KT4 Ultra) the machine needs very long until it reads mbr of the disk. what i exactly mean is, post boot goes with normal speed. all settings (FSB speed, DDR speed, CPU speed) are correct. after post boot, when it should start to load windows from the disk, it takes > 1 minute until the boot screen of windows shows up. after windows could boot, i don't have any problems anymore (speed rocks). i did not have this problem with the K7T Turbo2 board and except memory i still use the same components:
MSI KT4 Ultra w 1.4 BIOS
AMD Athlon XP 2000+ (not oc'ed) (~36-43C)
MSI G4Ti4200-TD(MS-8870)
Adaptec 39160 64bit dual (in a 32bit slot ;( )
3*Seagate ST318452LW X15 Ultra160 15K RPM
1 GB PC-2700 DDR (2x512MB)
Creative Soundblaster Audigy Gamer
Compaq NC3123 FastEthernet NIC
Logitech Mousman (dual optical) USB
Microsoft Sidewinder USB
the boot delay was not only when booting from the disks, i had the same experience when booting from cdrom: after post boot about 1 min. nothing and then excpected speed.
any idea?
thanks sidderz

thanks for the hints,
at the stage where boot is delayed so bad, HD access has not even been happened. the OS did not even start to load. so i don't believe the OS has anything to do with it. (except msi found a way to load the OS without read access to the drives )
like i said, right after post boot after floppy seek (my boot order: floppy, cdrom, scsi id 0) the machine just stops (for me it looks like bios is waiting for an answer and then times out) with a black monitor (but signal seems to be still there cause the monitor doesn't go to stand-by). first i thought about an IRQ conflict, but i took care to not use pci slots with shared IRQ's. when the computer starts to read from the disks, boot process is fast as expected. but until the system even starts to boot the os from the disks (read access to mbr on disks), more than one minute just nothing happens, not even disk access. i also checked if the computer is just frozen, but this was not the case, at least the keyboard was not frozen (numlock/capslock and reboot with ctrl+alt+del still worked)
honestly i believe it's a bios issue

KT4 Ultra crash on boot

Similar Messages

Maybe you are looking for