KT4 Ultra crashing/rebooting problems

Hi all, I've been having computer crashing/rebooting problems when I play 3d games since I got this board. It can happen between 1-40 minutes during a game session and when the computer crashes, the screen would garble up and reboot along with the garbled screen until I cold boot it. I thought it was a heat problem at first but the cpu heat displays at between 34C-39C. Also, when I tried switching out the video card with an older one, the computer works fine during gameplay, and my newer video card ran fine on a friend's computer. Does anyone know of a way to fix this?
System specs are:
Motherboard: MSI KT4 Ultra
CPU: AMD AthlonXP 2400
Power: 300watt
Ram: PC 2700 333mhz DDR 256MB
Video: Gainward Geforce4 Ti4200 Power Pack Plus! Ultra 650 64MB
Sound: Onboard
Thanks

by the sound of it try a bigger psu,antec enermax over 400 watts
make sure fan on cards not loose

Similar Messages

KT4 Ultra - SCSI boot problem

Hi,
I have installed a Tekram DC390U2W LVD SCSI adapter on my KT4 Ultra. My problem is that I cannot select any of the five connected SCSI disks as a boot device in the BIOS (BBS-n), nor can I select 'Legacy SCSI' as a boot device, they simply don't exist as options in the Boot Sequence menu. I've used this card (and were able to boot) without problem using a MSI KT266 motherboard, so I don't think the problem is the SCSI adapter. Any ideas would be appreciated.

I've disabled all motherboard options (Serial ATA Raid/1394/USB 2.0/GBLAN/Audio controllers), remove all PCI cards exept the Tekram card and tried it in all PCI slots without success. Also tried to assign different IRQs to the SCSI card in the BIOS. Tekram support responded that the SCSI card is fully PnP/BBS/PCI 2.1 specification compliant and they're unaware of any KT400 issues. There are issues (and work arounds) with this SCSI card when using it on motherboards with an on-board SCSI controller and older Award BIOS versions, but that's not applicable here.
Anyone out there using this SCSI card and motherboard got this combination to work as intended?

Another KT4 Ultra + 9700 Pro problem

Having invested nearly 300 quid on a Radeon 9700 PRo (Powercolor Evil commando 2) I decided to buy a new mobo with 8X AGP. I opted for the MSI KT4 Ultra, cos I already had a MS-6340 V5.0 it seemed a good/reliable choice. I went ahead and bought a KT4 Ultra. This arrived a couple of weeks ago.
I was awaiting a new CPU/fan (2200+) and new PSU so, I hadnt been able to build my new system up. In the meantime I had been keenly watching the forums re: KT4 /9700 problems.
When i came to put my system together, this is what i found:
1. System wouldnt boot up at all.
- So I took out the 9700 and put in a GF2, and the machine booted ok.
Installed latest via drivers, C-Media drivers using live update.
Upgraded Bios to 1.1
2. Im using a trial version of XP, which had 13 days (IRONIC) before activation was required. When I rebooted after BIOS upgrade, Windows insisted on instant activation of the product key and wouldnt load Arrrrghhhh!
After a re-install of XP I still was left with the same problem. The 9700 wouldnt work at all.
I checked the bios settings, and changed the FSB from 100 to 166 ( i have 512Mb DDR333 ) - no change.
AGP settings on auto, 128Mb Apperture
I had seen other with problems getting the 8X AGP to work with this mobo, but i cant get anything to work with it!!!
What else can I do? Is there someting fundamental I have missed?
I am thinking of sending the KT4 Ultra back to the shop and getting a mobo which works with the 9700! Any Ideas ?
BTW the Gcard still works ok on a MAINBOARD K7S5A

Thanx maesus
1. v1.1
2. 400w psu vtec - Not sure how well known they are!
I bought it from a computer fair from a guy selling ANTECH psu's . He had no Antech left, and suggested that these were good units. Having got it home and run it i believe him. In SANDRA all voltage levels looked stable and v close to nominal.
3. MS-6590 arrived on 18th Oct 2002 , so its almost ten days old.
Both items were bought on the net.
RMAing the boards maybe my only option now if i want to stick with th eboards ive got, but do u think i would be better to swap for a different KT4 board? since i believe other models of the KT4 dont have the 9700 problem, or is this not the case?
thanks again

KT4 Ultra-BSR - Drive problems?

Yesterday I purchased a KT4 Ultra-BSR. I am doing a clean install.
I have an Athlon XP200+, 2 x 512MB DDR Ram (PC2100).
On IDE1 I have put 2 x 20GB Western Digital HDs.
On IDE2 I have put a Pioneer DVR-A04 as Master, and a 100GB Western Digital HD as the Slave.
On IDE3 I want a 30GB Western Digital HD as Master, and a 40x Liteon CD-R/W as Slave.
I have installed Windows XP Pro (SP1) from new, and I have installed all of the drivers and utilities from the Drivers CD. My motherboard was shipped with BIOS Version 1.1
When I boot into Windows, I do NOT see the CD-R/W at all.
Also, the only way ro see the HD that's on IDE3 is when it's configured as an array (even though there's only one HD).
I would have preferred to have two HD's on IDE3 but NOT with any form of RAID configuration - is there a way of doing this?
Many thanks

Quote
Originally posted by Mastiff
[QUOTE[size=15]Also dudes, how did you get the Bluetooth to work on the KT4 Ultra-BSR??!? I'm desperate for help on this!![/SIZE]
I did it the simple way: Used Fujitsu-Siemens' Plugfree setup instead of the incredibly buggy MSI drivers. Then it worked perfectly with my PocketLoox and Ericsson T39. The hardware is the same. But still the range stinks (max 20 feet on my system), so I bought a full WLan setup instead.
Here's the URL (I belive it says it's only for Fujitsu-Siemens' computers, but that's just standard manufacturer's bull. 8)
Bluetoot-drivers
And an explanation concerning pocket pc's and the installation:
FirstLoox-forum
[/QUOTE]
You've misunderstood my problem. I have the MSI KT4 Ultra-BSR motherboard which has a bluetooth module which needs to be connected to the motherboard, however, I don't know how to connect it (PHYSICALLY).
Therefore I need someone with the same board to tell me how they did it.

KT4-Ultra-BSR Video problem

My PC was running fine. I have the KT4 Ultra BSR with XP2200+. I WAS running a TNT2/Riva 32MB GFX Card, and all was OK. I then bought a new graphics card - a 64MB Triplex Xabre-Pro (AGP 8X). I installed the card, but with it installed, the PC would not even attempt boot.
I took the card out and put my old TNT back in, and the PC worked OK.
I tried the jumper settings on the Triplex card, but it still failed to boot.
NOW the PC won't boot - even with the TNT card in, BUT it will boot WITHOUT a gfx card (although it gives the customary beeps).
What am I doing wrong here?

OK, well it IS a 3.3V and 5V PSU.
I have tried booting withou the NIC installed, and it made no odds.
I have cleared the CMOS
I didn't remove the TNT drivers, but I don't feel like that's the problem since the machine does not power up.
I have tried a combined 300W 3.3V / 5V PSU that was in the machine before the gold PSU and it doesn't power on with that one in either.
On BOTH PSU's the machine WILL boot without either of my 2 graphics cards in it, but will not boot with either of them (whereas it did at least boot with the TNT before)

Kt4 ultra windows install problems

hi i just bought a new kt4 ultra board, the 1 with bluetooth, and i have hhad nothing but problems, i cant seem to get windows to install, i get lots of copying errors, i have changed the cdrom drive etc, still get the same thing. i Got an xp1800, 128 pc 2100 ram,geforce card, i know i need to get more ram, but surely with what i got it should setup windows, i understand its a memory problem but i cant seem to find out what exactly it is, any help any1 can give would be very appreciated

http://www.memtest86.com on ram full test

KT4 ULTRA FISR SATA Problem

I really need some help here. I have a KT4 Ultra board with SATA Interface and a brand new Seagate Barracuda 120 GB. On to the problem .. when i booted up the computer for the first time, it detected my disc. After that .. i was testing som different settings in the BIOS .. and had to clear the CMOS Now .. it won´t detect the drive at all. It says something about "No drive attached to the FastTrak controller. Bios not installed/loaded" I have installed all drivers and stuff that came with the board but no luck. Is the driver loaded into the BIOS from the beginning or? How do i get the d*amn board to detect it again? I can´t even enter the bios setup (for the SATA controller.. ctrl+f) So .. i can´t really do .
Help!

It says jumper (Factory only) so i don´t think u are supposed to jumper it. It´s master by default. At least that´s what seagate claims =) Or?

KT4-Ultra-Onboard sound problems

I bought my KT4 Ultra in September and I've heard some talk about being defective. Just to start off by saying that for it may be my problem.... Anyways, I'm having problems with my onboard sound. When I play music, my sound kinda stutters. To best describe it, my sound doesnt skip or anything, but every now and then i hear an extra "drum beat" in my music where there shouldn't be. Please post if you know anyhing about it. Thanks.

Thanks Vatoloco
I know my problem doesnt have anything to do with ripping or the software. All I knowis that the problem is with either my motherboard or something involved indirectly...
Anyways, to help you out, thry using different software and see if that's the problem. If not, try unplugging all your IDE cables and audio cable in ur case and reconnecting for you might have a bad connection. Lastly, check out your cd drive.

KT4 Ultra, amd 3000+ problem !!

Hi All,
Am having problems getting my system to recognise that i have a 3000+ athlon installed, have set the FSB as 166 mhz.
But system is still showing it as a 2700+, will a bios update solve my problem ?
My board is a KT4 Ultra (MS-6590).
Hope someone can help, would appreciate all advice !!!!
Cheers thesicillian

AXDA3000DKV4E 3000+ 2100MHz 10.5x 200
AXDA3000DKV4D 3000+ 2167MHz 13x 166
i suggest you have the 200 fsb one,set it to 100 fsb
bet it boots at 1050

KT4 Ultra Promise Raid Problem

Hi,
I recently purchased a KT4 Ultra board to replace a K7T 266 board. After connecting my RAID 0 array to the 40pin IDE RAID controller on the new board, I was surprised to discover that only one hard drive was recognized. I tried every jumper combination, even iterating through ones I knew would be invalid. I switched cables, and I even tried a different hard drive. Since the two Serial ATA connectors naturally only support one drive, I would hope that some errata in the BIOS would not cause the old 40pin connector to only allow one drive. Who knows.. that was my only guess, as I've tried everything I can think of. Does anyone have any ideas?
Thanks,
Jeremy

ide 3 acts like a sata channel and will read one drive only
as it says on boards page you need at least one sata drive for raid
you cheapest option is 2x sata convertors
abit make them and sig do as well
i say 2 as i would not have one sata one ide in raid myself
ps this is the nforce forum not via

KT4 Ultra USB boot problems

My old floppy crapped out on me a while back so I thought I could use my USB hard drive or my keychain flash drive to boot the system (for BIOS flashes and such) When I go into the BIOS, I can see my USB HD and Flash drive, but no matter what order I put the boot sequence in, it never boots to either drive. I've even tried a USB floppy drive and that didn't work either. If the BIOS sees the USB drive and the drive is bootable, should the system boot to them?
KT4 Ultra SR
Athlon XP 2400+
512 MB Kingston 333 DDR
128 MB GF4 Ti4600
SB Live
Intel Etherexpress 10/100

try setting main three boot options to none
will it go for it from boot up other device

Endless Crash Reboot Problem

System had an error - system reboot - recrashed when tried to reopen windows due to " Reopen windows when logged back in " . . . well over 20 times within 30 minutes
SSHD data lost perhaps due to repeated crash / dumps . . . reinstalled from time machine
Why is this feature still in the OS ? . . . IT WAS THE PROBLEM and the system crashed the SSHD data after many reboots
How do I disable the junk that caused the real problem ( crashing the SSHD ) ?

I have an RV220W that is definitely crashing and rebooting 2 or 3 times a day. I enabled more logging levels and without a doubt it's crashing. I am running firmware 1.0.4.17. There is no pattern of usage that causes the crash- it's apparently at random. This device is less than a month old. Any suggestions?
I have to say I'm utterly baffled by the request to reinstall utorrent. What on earth does that have to do with it? Nothing should be able to crash the router. This isn't a $35 walmart router.

KT4 Ultra crash on boot

Can anyone help please
System crashes at boot
using
AMD Athlon XP 2400
512MB DDR / PC2700
MSI KT4
But sysem runs fine with old AMD 900 chip

Quote
Originally posted by wonkanoby
d bracket lights stop were
psu combined watts and amp details of its label
d bracket lights all red
ac input 115/230VAC 8A/4A 50/60Hz
AC OUTPUT 115/230 VAC 1A/0.5A 50/60Hz
DC OUTPUT +3.3V +5V +12V -5V -12V +5VSB
14A 30A 15A 0.5A 0.8A 2A
165W max 9.6W max
350W
Thanks

Kt4 ultra-sr 6590 problems

Help! Just got done putting together my new computer. Installed everything, turn on power and it starts to post. However, a little error comes up and says cmos/ checksum bad! It says press f1 or f2 to get to bios but i cant get the board to find my keyboard. Ive tried ps2 port and all usb ports but no go. Ive tried three different kinds of keyboards with usb and ps2 connectors, but still nothing! everthing else has power on the board. PLease help! later

Thx for reply! Well i kinda tried that already, but for some strange reason the cmos reset came in the 2-3 position. So i thought that might be the reason but when i put the cmos reset in the 1-2 position the power button wont even work. When i put it back on the 2-3 position it will post, but same problem ;( According to the book i swear it should have come in the 1-2 position. Im sorry if i sound like a tard but im a 36 year old computer noob :D Please help im dying to try my new puter! thx )

KT4 Ultra 6590

Hi!..
I got recently problem when i installed my new ddr-memory
It's a: ddr twinmos pc3200 512Mb (400mhz FSB) with winbond.
Something weird happened when running c&c geneals.
An area on the screen lost the graphic suddenly and went like black, and then 1 sec. after the whole system freezed. music hanged to beep.
And the only thing to do was reset.
Before this 512 memory I had a twinmos pc2100 256 Mb (266mhz) and had never any problems at all....
I have heard from a friend that kt4 ultra 6590 has problems with running memories in 400Mhz ...It worked though when testing to play c&c generals directly in a 4 hours period after I installd the memory this night.
But now something protested. ?(
But everything else works excellent in windows and all (knock in wood ;P )......huh???
Pleased for answers
Help!
/p

http://www.memtest86.com , that can tell you if the memory and the board are getting along.
Let it run for about an hour.
If the test doesn't find a problem you should check and see if lowering the memory to 333MHz helps.
It might also be the power supply not handling it all with the new RAM and crashing under the stress.

KT4 Ultra crashing/rebooting problems

Similar Messages

Maybe you are looking for