KT4 Ultra Ide3/Sata connection problem

I have had this motherboard for about a year and have now decided to utilise one of the sata connection. the problem i am having is that i cant get either the bios to recognise a drivr connected to eide 3.
i have tried to rebiuld the system with a hard drive connected to the sata connector but cant get windows to recognise the sata drive.

control plus f and make an array
set scsi second to cdrom in boot order
f6 as xp install starts feed in raid drivers

Similar Messages

KT4 ULTRA FISR SATA Problem

I really need some help here. I have a KT4 Ultra board with SATA Interface and a brand new Seagate Barracuda 120 GB. On to the problem .. when i booted up the computer for the first time, it detected my disc. After that .. i was testing som different settings in the BIOS .. and had to clear the CMOS Now .. it won´t detect the drive at all. It says something about "No drive attached to the FastTrak controller. Bios not installed/loaded" I have installed all drivers and stuff that came with the board but no luck. Is the driver loaded into the BIOS from the beginning or? How do i get the d*amn board to detect it again? I can´t even enter the bios setup (for the SATA controller.. ctrl+f) So .. i can´t really do .
Help!

It says jumper (Factory only) so i don´t think u are supposed to jumper it. It´s master by default. At least that´s what seagate claims =) Or?

KT4 Ultra and SATA

I have a KT4 Ultra that supports SATA Raid and Im looking at getting a new HDD. CAn I run my old PATA HDD with a SATA HDD without it being in raid format or do the disk have to be in a raid format.

Hey guys, how about this:
MSI KT4 Ultra SR, Win2000, PDC 20376 Promise Serial ATA chip on board. WD 40gig IDE hd as primary on IDE 1. Attached a Maxtor 120gig SATA to the Serial ATA 1 connector. While booting did NOT setup an array. Windows 2000 in Disk Management under Device Manager/Disk Drives has now two folders, one for the WD and one that says SCSI Disk Device. It's also also recognized under System Information/Components/Storage as SCSI controlled by the Fast Track 376 controller. Is this a proper way to setup the serial Maxtor as an extra single drive in the system attached to the Serial interface? Is this even possbile? My problem is that while the drive is recognized as a SCSI disk device as described above, it is NOT seen under Disk Management as a new unformatted drive with a new letter. Assuming the above setup is correct, how do I format the drive so Windows can use it? Any help will be greatly appreciated, thank you.

MSI KT4-ULTRA & WD SATA RAPTOR

I have this KT4-Ultra with Promise SATA controller onboard and until now I did not know if it works well.
Today i've bought the SATA hdd from WesternDigital - the Raptor, and i'm very unsatisfied by the performance.
I've got only 58mbps burst speed and 48mbps medium on HD Tach. And i know that this is not ok. It should be far better I've readed all the reviews.
The drive is conected in a 1+0 Stripe Array. I'm using the latest driver for the controller. I had trouble before with this mainboard [thread] and i think it has something to do with the BIOS.
This i found it to be iritating - the HDD cost a lot more than the mainboard(wich is expensive too). I still think that the mainboard is the problem.

Quote
Originally posted by wonkanoby Meseriashu
you have got it jumperless not master
There are no master or slave or cable select settings on SATA drives as there can be only one SATA drive per cable/channel. The jumpers on the Raptor set the power management mode of the drive on spinup.
http://wdc.custhelp.com/cgi-bin/wdc.cfg/php/enduser/std_adp.php?p_sid=PtNY5SHg&p_lva=&p_faqid=958&p_created=1050530240&p_sp=cF9zcmNoPTEmcF9ncmlkc29ydD0mcF9yb3dfY250PTImcF9zZWFyY2hfdGV4dD1qdW1wZXImcF9zZWFyY2hfdHlwZT00JnBfcHJvZF9sdmwxPTk1JnBfcHJvZF9sdmwyPX5hbnl_JnBfY2F0X2x2bDE9fmFueX4mcF9zb3J0X2J5PWRmbHQmcF9wYWdlPTE*&p_li=

KT4 Ultra FISR AGP Speed Problem

Hi all,
I've got a bit of a problem and was wondering if someone can help?
I have bought the KT4 Ultra FISR and am having a problem when trying to use it with my 8x AGP Nvidia ge Force 4 ti 4200 but the bois wont let me change the AGP speed to 8x, it insists that the highest it can go is 4x. ;(
I have run the newest 3DMark03 and it's showing that my AGP is only 2.0 and not the 3.0 that is meant to be with the board?
I was wondering if this is the problem?
I have double checked with the Graphics Card Manufacturer and they have confirmed that my card is an 8x card and I know that it was running at 8x on my last board.
I have done all of the Auto updates on the MSI motherbaord update utility but there's still no joy.
Any help would be greatly appreciated!!
- Ricky

Hi there
Well I have the Inno36 Ti 4200 8x AGP card:
http://www.ivmm.com/inno3d/geforce4/products_gf4_ti_agp8x_reviews.html
I know it's not the best card on the market but it should still be able to operate at it's advertised speed :P
A couple of the guys here at EA bought the card and theres are working fine on thier boards :(
I am not totally sure of the version number of my bios but does 1.3 ring a bell?
I wont be able to check the version till monday...
Like I said before.. I did notice that 3dmark03 noted that I was using agp 2.0, is that right?
- Ricky
P.s. Thankyou for taking the time to help me out Its much appreciated.

KT4 Ultra APCI power management problems

After I boot I must go into Win98 power management propertys and apply to get any power management functions to work. And then all I can get is monitor blank and hardrive power down. Unit will not go into suspend.
If I use the suspend feature in power down the unit will go into suspend (Susp to ram) but all the fans keep running. When I come out of suspend, the system becomes unstable and quirky.
Can anyone help me get this running the way it should.
Joel Gunn
Kt4 Ultra V 1.0 Bios V 1.4 - AMD 2100 XP
Win98 Se
Nanya 256M - 333 Ram X2
Ati Radeon 7500 AIW
Enemax EG 365P -VE
Two Maxtor 80Gig Ata 133, 7200 on a Promise TX2 Ultra 133 controller.
Aopen Modem
CD rom and CDR/RW

Hi,
Check whether all the supported patches are installed.
Regards,
Dharani
SlashSupport
A couple of weeks ago I installed quite a few of the
patches in the recommended list.
Since then, I get the following message repeated
continually in the console window:
DPMSSet: Invalid argument
Power management problems
I'm runnig solaris 8 on a ultra 5. I looked in the
power.config file and in the startup scripts, but
couldn't find any reference to "DPMSSet." Any ideas on
the cause and solution of the message?
I never use the powerd daemon, so killing the process
seems to eliminate the messages.
Thanks,
Gerhard Kuhn
[email protected]

KT4 Ultra and Audigy 2 Problems

After install the CRC Error Bios I been have a probem w/ my sound card. I can now hear the cd-rom run , dvd load , and mouse scolling on my speakers. Also the creative program load painful slow now and the speaker test no longer work when I test the speakers out. The program and speakers were work fine before the CRC Error Bios. Do you know what it could be ?
System Config:
CPU: 2200+ XP
Motherboard: KT4 Ultra-SR
RAM Slot-1: Kingston 333 512 MB CL 2.5
RAM Slot-2: None
RAM Slot-3: None
display card: AIW Radeon 9700
IDE-1M: Western Digital 200 GB SE 8MB
IDE-1S: None
IDE-2M: Samsung 48x-16x-48x CD-R/RW SD-616Q
IDE-2S: Samsung 16X DVD SW-248B
IDE-3: None
SER-1: None
SER-2: None
PCI-1: None
PCI-2: ATI TV Wonder PCI
PCI-3: None
PCI-4: 3com EtherLink 10/100 PCI TX NIC 3c905B-TX
PCI-5: Creative Audigy 2
PCI-6: None
PSU: (Antec AMD Approved 350W)
BIOS revision: 1.3 Beta
Operating System: WIN XP
VIA 4-in-1 drivers : 4.45
other drivers, services or applications might affect the data transfer such as : None

I just reinstall the driver....
Now the system is crashing. The whole blue screen of death thing. Anytime I click on EAX console it give me an error or crash. What going on???

Ultra 10 serial connection problem

Hi guys,
I've got an Ultra 10 that is functional and I can connect to it over the network. However I am trying to connect to Serial Port A and it's not happening.
I've done the following:
eeprom output-device=ttya
eeprom input-device=ttya
and I am using connectors 530-2889-03 on the Ultra 10 side and 530-3100-01 connected to my laptop's serial port, I am not sure if I got the right connectors. I've also changed /etc/remote to point to ttya , but to no avail.
thanks for your help

have you read the entries at the beginning of this forum (at the top of the page)?
sticky: How to connect to Sun Systems via TIP
do you have access to a null modem cable?
haroldkarl

KT4-Ultra FSIR Gigabit ethernet problem

Hello,
just wondering if anyone has had a problem with getting the onboard gigabit ethernet to work? I've had some problems, but I connect to a functioning 10/100 network, so that may be the problem.
thanks,
bill

Hi Gert.
Thanks for the reply. No I don't know what GIGABIT is!?
I thouth 'Broadcom NetXtreme BCM5702 Gigabit Ethernet' was the name of the network card sitting on the motherboard!?
It looks like I'm accessing internet via that network card from Linux (which I am using right now)...
So do you know what I need to do to get the integrated network card work in windows 98. It should've been 'plug n play' but it don't seems to work. This is what I've tried so far (well, at least something like this): 'Control Panel -> Network -> Adapters -> Add -> Broadcom -> Broadcom Gigabit Network... something...'.
Is this aproach totaly wrong...
BR
karnbo

KT4 Ultra-B BIOS Update problem

Well, I runned Live Update BIOS and found out that I didn't have the newest version. So i downloaded the newest (1.4), and followed the instruction for the installation. After it was installed, every thing seemed okay. Untill I started the PC, then I got an 'error' message:
CMOS Settings Wrong
Press F1 to Run SETUP
Press F2 to load default values and continue
I checked the CMOS Settings, nothing I could find was wrong. So everytime I start the PC I have to press F2, or else it won't start, it will just jump back to that message. This is not so much of a problem, but when I have to use the default values from now on it _IS_ a problem, because default FSB is 100MHz, and I loose alot of CPU. I now have AMD Athlon 1500+ 1,35GHz because of that BIOS update. What I really should have is AMD Athlon 2200+ 1,8GHz.
So anyone that could help me with this problem ??

There is a reason why it did not work.
When you buy a board and put a CPU in it, the board may not detect the CPU correctly,
So if your cpu was a 1470Mhz Athlon and the board detected it as 2.2Ghz what would happen?
The CPU would try to run at 2200Mhz and blow up
So manufacturers such as MSI set the CPU FSB to 100Mhz, must modern CPUs run at 166Mhz so by having it at 100Mhz you prevent the board from overclocking the CPU.
Do you see how that is a safety feature?
Now when you flash a BIOS you clear all your settings and the board gets reset to the safety defaults (100Mhz). This also happens when you clear the CMOS using the jumper, thats why it did not work
I assume someone else originally setup the motherboard and CPU settings for you?

KT4 Ultra: problem config. raid array IDE3

I owe the MSI 6590 KT4 Ultra BSR mainboard and I have difficulties configurring the RAID array in striping mode, on the IDE3 controller.
The manual describes on page 2-18 it's possible to connect up to 2 hard drives, cdrom, 120mb fd and other devices to the IDE3 controller.
Unfortunately only one of my two MAXTOR D740X-6L (6L080J4) 80gig drives is recognized by the array.
One Maxtor hard drive is jumpered as MASTER and the other is set up as SLAVE.
When I hook up the cable to an ordinary IDE port (eg IDE1) the two drives are properly recognized.
Both drives can be formatted using the regular IDE ports, this means without any cluster errors or other errors so the drives are physically OK.
Before I wrote this post I checked the support section again to make sure I am using the latest BIOS which is 1.1. I also downgraded to 1.0, but that didn't solve my problem either.
Since I work in a computer shop now and then I had the opportunity to check two Maxtor Fireball3 30gig drives on a different MS-6590 RAID board (BIOS 1.1.) and exactly the same problem occurs: the 2nd drive won't be recognized in the ARRAY on IDE3.
Please tell me what to do to make the striping option fully work on my two IDENTICAL Maxtor hard drives since MSI support came up with a standard email, which didn't cheer me up at all. Hopefully this time they will investigate this matter since no doubt more people will experience this.

Thanks for the quick response, though it's not satisfactory for me (of course).
Actually before installing the new KT4 Ultra I owed the KT266 Pro RAID motherboard. It's true this board has two controllers for the RAID option. Nevertheless because after reading the manual of this new board I was convinced I could connect two hard drives on the IDE3-channel. This is the reason I decided to go ahead and to upgrade to this new mainboard.
I guess I have to go back to my employer and fall back again to my KT266 (MS6380).

Sata Raid problems with MSI KT4 Ultra Via kt400 chipset

ok i am having major problems setting up my sata raid in my brothers msi KT4 Ultra via KT 400 chipset
it comes up with my irq settings are wrong
my hard drives are WD 120 GB 7200rpms SATA - sold my mobo asus A7N8X - Delux and used my bros mobo above but just cant get them to work if ne one has ne idea on how to fix it (bios is still factory default do i have too flash it to get it too work etc)
would help lots thanx

you dont need multiple threads on the same thing

KT4 Ultra-BSR - Drive problems?

Yesterday I purchased a KT4 Ultra-BSR. I am doing a clean install.
I have an Athlon XP200+, 2 x 512MB DDR Ram (PC2100).
On IDE1 I have put 2 x 20GB Western Digital HDs.
On IDE2 I have put a Pioneer DVR-A04 as Master, and a 100GB Western Digital HD as the Slave.
On IDE3 I want a 30GB Western Digital HD as Master, and a 40x Liteon CD-R/W as Slave.
I have installed Windows XP Pro (SP1) from new, and I have installed all of the drivers and utilities from the Drivers CD. My motherboard was shipped with BIOS Version 1.1
When I boot into Windows, I do NOT see the CD-R/W at all.
Also, the only way ro see the HD that's on IDE3 is when it's configured as an array (even though there's only one HD).
I would have preferred to have two HD's on IDE3 but NOT with any form of RAID configuration - is there a way of doing this?
Many thanks

Quote
Originally posted by Mastiff
[QUOTE[size=15]Also dudes, how did you get the Bluetooth to work on the KT4 Ultra-BSR??!? I'm desperate for help on this!![/SIZE]
I did it the simple way: Used Fujitsu-Siemens' Plugfree setup instead of the incredibly buggy MSI drivers. Then it worked perfectly with my PocketLoox and Ericsson T39. The hardware is the same. But still the range stinks (max 20 feet on my system), so I bought a full WLan setup instead.
Here's the URL (I belive it says it's only for Fujitsu-Siemens' computers, but that's just standard manufacturer's bull. 8)
Bluetoot-drivers
And an explanation concerning pocket pc's and the installation:
FirstLoox-forum
[/QUOTE]
You've misunderstood my problem. I have the MSI KT4 Ultra-BSR motherboard which has a bluetooth module which needs to be connected to the motherboard, however, I don't know how to connect it (PHYSICALLY).
Therefore I need someone with the same board to tell me how they did it.

Error detecting promise sata controller on kt4 ultra

Hello,
I've searched the forum and "the rest" of the internet without finding a solution to my problem.
The problem is: Normally when you boot the kt4-ultra you will have a message saying "FastTrack 376(tm) Bios version 1.00.0.18(c)2002-2005 Promise Technology, Inc." and then either No drive attached to FastTrack Controller, The BIOS is not installed or information about your HDD configuration.
In my case sometimes without any reasonable explaination my computer won't detect the promise fasttrak controller AT ALL! It just jumps right over it, as it didn't excists. This is very strange since it's enabled in the BÌOS settings and it could be detected at the next reboot, or in many cases it wont be detected again for several days
As far as I can see it has nothing to do with the harddrives connected to it, as it happens anyway either with a SATA disk connected, IDE disk or no disks at all....
If anyone could help me out with this problem I'll be very gratefull!

Quote
Originally posted by Fredrik Åsenius
How are your hard disks configured, and your CD/DVD etc?
I've litary tried every possible combination. The problem remains even with no disks or CD/DVD drives installed on the Fasttrak controller or IDE 1/2. Sometimes the controller is detected, sometimes not.
I should point out that if the controller is detected it always find my HDD who's connected to it and it works fine in Windows. But if it's not detected Windows will find a new hardware and try to install drivers to it, but it won't work cause the hardware is reporting an error and Windows will ofcourse not find a disk....
Quote
What operative system do you have? On a quick search I found mostly linux related problems, though I was not too thorough.
I have Windows XP, but I don't think it matters what OS i'm running.
On the searched I've done Im only finding Linux and compability related problems...
I've had this problem for over 6 months now and I'm getting a BIT tired the shitty controller....

KT4 Ultra SR/ IDE3 only see's 1 drive

I got a new KT4 Ultra - BSR (SR with bluetooth); and the IDE3 RAID connector only see's a single drive. If I connect the IDE cable to IDE1 or IDE2; both drives are seen correctly.
Master/ Slave Jumpers set correctly.
Tried a few cables; but they are OK; since they can see & access the drives via IDE1 or IDE2.
Any ideas??
:(

im currentley trying to get the 4 drive highpoint one as the nforce boards look like being like this as well
get the 4 sell 2 sata convertors then later sell the sata card when there are more sata drives about seems to be only option
ive spent weeks trying to find the convertors without the card

KT4 Ultra Ide3/Sata connection problem

Similar Messages

Maybe you are looking for