KT4 Ultra memory/cpu requirements

Does the kt4 ultra HAVE to have the "certified" ddr400 ram for it to work, or work faster?
Is the highest cpu possible a xp 2700+ to fit into the kt4 ultra?
i want to know, because iam builing a puter and i was going to get a 2500+, but if it only supports up to 2700+ i might as well get it.
-Ryan

Quote
Originally posted by ctfalconk
Ok, so I can get up to 3000+/3000+barton, but will that change in the future?
Say I buy a athlon xp 2500+ barton right now, and then a couple years from now i want to upgrade, what if theres a 4000+, could I get that>? or would I have to get a whole new motherboard to upgrade my cpu, because it will only support up to 3000+?
Lets get real here please!!
Does anyone really know what cpus will be around in two years time. AMD can't even get their timetable sorted for the 64bit processors yet.
If it's a barton 4000 then it will probably run on your KT4 Ultra with a bios upgrade. Hammer CPUs will be on a totally different motherboard, and you can't buy one now!!
How much life do you really expect to get out of a motherboard, technology changes so fast that in two years time you will probably need a different type of memory, hard drive interface and graphics sub system.
The KT400 or Kt400a chipset gives you a good base for the forseeable future, for anything else it going to be a crystal ball job.

Similar Messages

KT4 ULTRA PROCESSOR HELP REQUIRED.

Is there any wise person who can enlighten me with the most recent information regarding the largest AMD processor that can be used to replace my current XP 2200+ processor on my KT400 ULTRA mainboard without the need to overclock. MSI emailed and did not get back to me. Any advice would be appreciated. Thanks
CPU : AMD Athlon XP 2200+ 1800 MHz
Bus Speed : 133 MHz
Motherboard : MSI MS-6590
System : MSI MS-6590
BIOS : AMI Version 07.00T
Memory : 512 MB

Quote
your memory will need to be PC 2700 or PC 3200
not sure what you have now.
KT4 Ultra CPU Support
KT4 Ultra bios page may need at least bios 1.3 to recognise Barton 3000+

Kt4 ultra memory problem

Hey guys, hopefully someone here can recommend some help! I have the kt4 Ultra motherboard and i've had it for about 8 months. I have an amd 2600+ and up until now i've had 2 256mb 266mhz micron ddr ram chips in it. I added a 512mb 266mhz crucial memory chip today. No matter what I do it will never recognize more than 512mb ram. I can just run the 2 256mbs and it recognizes 512, i can just run the new 512 and it recognizes fine, if i put all 3 in (or the 512 and one 256) it reads 512. Everything runs ok, no lockups no reboots anything like that, but i'm out 512mb of ram.
I flashed the bios to the newest version but still no help.
I have the bios set to "spd" and i tried playing around with those numbers but it didn't help.
anyone have any ideas?
thanks in advance!

Yes I am starting to realize that I never should have tried mixing brands. I attempted what you said and its recognizing the 512 only. Any suggestions (besides eating the 15% restocking fee and sending the new one back)?

KT4 Ultra / Incorrect CPU report

Hey chaps, I have had a look around the MSI site and forum, but cant seem to see any suggestions of a resolution for this:
KT4 Ultra (BIOS A6590VMS.140)
512 DDR Ram
Was running very happily and reporting correct CPU speed for an XP1800+
Swapped CPU for a thoroughbred XP2600+, flashed BIOS to latest, set the BIOS settings to as directed in the CPU support table (FSB 133, ratio="auto"), and the CPU is reported as XP2000+
Any ideas chaps or are we looking at faulty CPU?

Quote
there is no 12v connector on the KT4 Ultra (well, not on mine at least!).
Oh! He he, sorry :D ! I had the KT6 from another thread in mind...
Quote
BTW you still owe me beer, I think
Not yet if we talk about the same thing. But then: Muuuuch beer and even muuuuch moooore cookies. :D

KT4 Ultra ond cpu voltage

IS there any way (modified bios etc.) to use more than 1.7v with 1700XP cpu?

Quote
Originally posted by manocheese
You void the warranty as soon as you overclock anyway.
Not necessarily true

Raid & KT4 Ultra BSR

;( Can anyone save my sanity!
Read all about updating PC, thought easy, I can do that. During summer fitted extra memorey 512, fitted new hard drive, then an extra one for back ups, all well so far, then at Christmas bought KT4 Ultra BSR board & AMD 2400XP. Fitted ok no probs, great.
So why can't I understand how the hell to get Raid to work. The guide is about as useful as a smack in the mouth. Can anyone point me in the right direction to get an easy to understand guide to which HDD connects where and what I do with the jumpers on each. Tried configuring as Master and Slave on same cable to IDE 1 works Ok. Then tried same on IDE 3 only MAster shown and cannot configure raid. Please help before I trash it!

hi,
i had the same problem,
i have pull the little white mini plug of the harddisk where you can put it on master/save/..........
that restarted my compu and in to the set actived the raid / serial controller.
than you niet to configure your harddisk ( push ctrl-f)
and than you use nr.1 (auto........).
restart and normaly is the job al done.
jupliner/belgium.
mb: msi kt4 ultra bsr
cpu xp 2200.
256 mb/ddr/333mhz
big tower
geforce2
western digital 80gb/7200(8mb cache)
liteon 52x24x52
16/48 dvd

KT4 Ultra FISR & DDR400 memory ?

Can someone please help....
I have a KT4 Ultra, {BIOS v1.1} and an Athlon T`bred 2700+ which I want to run at 166fsb.
The problem is that when I use my PC400 DDR RAM module,[TwinMos} which is on MSI`s supported memory list,the thing will only work at 166fsb ,that is 333MHz not
the 400MHz it`s meant to run at.....does anyone know a way around this ?
Also,according to MSI`s website,the 2700+ should run at 166 with a ratio of 15 ,they say they`ve tried it and it works...well not for me it does`nt...I have to set the ratio to "Auto" in the bios to get it to run,and it does so at 13 according to Fuzzy Logic.
Now my CPU is running at 2.17GHz which is it`s advertised speed...so where do MSI come up with thier 15X166 figures?

Yeah thanks Bas...but I`m happy with the speed of the cpu,its the memory thats underperforming.
The TwinMos PC400 DDR RAM will only run at 333MHz,and not the 400MHz its supposed to run at whilst the fsb of the cpu is set at 166MHz......
Although when I drop the cpu fsb to 133MHz the DDR RAM appears to run at 400MHz,according to the bios initialisation screen at bootup.
So for now it seems that I can either compromise my CPU speed and run a 2700+ at 2100+ to get the most from the RAM......or I can run the CPU at 2700+ and settle for slower memory speed.
Add to all this the fact that at the moment PC400 DDR RAM is no faster...sometimes even slower than PC2700,you can drive yourself crazy.
A ;(

KT4 Ultra-BSR multipler & CPU volts on XP2400 dont work!

Well after several atempts and clearing the cmos several times the multipler dosnt work on XP2400 and when you go to change the cpu voltage from auto it comes up with strange symbols not a voltage to select! so iam stuck at 141fsb and CPU voltage set to auto i can change the FSB only except lower or to 141, why is it asus and epox can change the multipler and we cant on our MSI KT4 Ultra, iam disapointed and who wouldnt be after all others can change there multipler!
any surgestions would be welcome and i think MSI should address this problem with a bios update and also look at the voltages for CPU as symbols mean nothing to me! ?(

Quote
Originally posted by MSIconvert
Hi, well bluetooth lol, ok load bluetooth software from your instalation cd rom, dont load the mobile phone software as it causes trouble, then all i did was load the nokia pc suit that came with my nokia 7650, turned on blue tooth on my phone and then asked the phone to find bluetooth, problem it couldnt, but my pc found the phone, you have to make up a password and identify yourself over the blue tooth network, the software says it will conect auto, but it dosnt, you have to conect the 2 devices manuly every time, its faster than cable conection, but one problem i have found is that disconecting can cause problems, 1 out of 5 times when you disconect your pc loses the bluetooth conection and the only way it can find the hardware again is to unplug the arial device inside your case at the usb plug, reconect and it finds it again, a real pain i gota say, so much so i cant be botherd to use blue tooth anymore as iam fed up of takeing the side of my pc case off to get it to reconize the hardware again, but it does work when its all working and the usb finds the hardware, i hope this helps just a little but its not so easy to set up and the software isnt that easy either, maybe an update in the future will make it easyer to use.
matt 8)
Oops, I meant how did you connect the module to the motherboard?? I can't find anyway in which to connect it directly into the mobo, and I didn't get a cable with mine. (I still haven't got to the software side of it yet - the hardware has been my prob for the past few weeks, no-one seems to be able to answer me).
Hope you can tell me how to do it (pref with some pics or something coz I'm starting to think my retailer sent me the wrong board).
Thanks!

KT4 Ultra CPU Upgrade Question

I am trying to upgrade my CPU from a 2100 XP to a 2800 XP on my KT4 Ultra and am running into trouble. I was under the impression that all I had to do was turn up the FSB frequency in CMOS and everything would be OK howerver this doesn't appear to be the case. Currently the FSB Freq. is set to 100 and I can get it above 104 or the system will not POST. Has anyone out there put a 2800 with the latest BIOS in a KT4? What setting need to be changed and what values should be used in CMOS??
Help please!!!!

set to 166

KT4 Ultra & XP 2800 CPU

I currently have a KT4 ultra board with Crucial Pc2700 DDR Ram (running at 333mhz) current fsb 146Mhz. I am wanting to upgrade the CPU to an XP2800.
Does anyone have one running at 333mhz on this board?
Is it stable?
Is it fast?
Comments welcome

Quote
Originally posted by fullforcefitness
I currently have a KT4 ultra board with Crucial Pc2700 DDR Ram (running at 333mhz) current fsb 146Mhz. I am wanting to upgrade the CPU to an XP2800.
Does anyone have one running at 333mhz on this board?
Is it stable?
Is it fast?
Comments welcome
I have a 2600+ 333FSB running on a KT4 Ultra not overclocked (set at 166).
KT4 Ultra (MS-6590)
AMD 2600+ 333FSB
Volcano 9 / Artic Silver 3
512MB Corsair PC3200 Cas 2.5
Chaintech GF4-MX440 /64MB DDR
400W Allied PSU (ATX 400 P4)
+3.3v@24A
+5v@35A
190W combined
Linksys LNE100TX ver.5.1 NIC
AMI-IA92 PCI Modem (Intel Chipset V.90/V.92)
Maxtor 60GB 7200RPM ATA133 HD
FXEF

Kt4 ultra showing wrong cpu

my kt4 ultra 6590 is showin i have a 1800+ cpu when in fact i have a 2400+ how do iget it to see correct cpu
what settings should i alter exactly as theres a few

I think you could be right there actually
List of Athlon XP CPUs:
http://en.wikipedia.org/wiki/List_of_AMD_Athlon_XP_microprocessors

How much memory and CPU requirement to deploy ADF Faces application ?

Hi All,
Is there any formula or docs to help me to determine how much memory and CPU requirement for IAS server, to deploy ADF Faces application ?
How much memory / CPU GHz required per 1 user ?
We plan to develope web based ERP application using ADF Faces and ADF BC.
Pleasssee.. give me any aclue.. I need it so badly..
Thank you for your help,
xtanto

xtanto,
there is no formular for this. Note that it is not only ADF Faces but th emodel layer in particular that adds to this requirement.
Frank

Does the KT4 Ultra Support Sempron CPU's ?

Does the KT4 Ultra support Sempron CPU's ? The CPU support page doesnt seem to mention this motherboard....
If it does what BIOS rev do I need ?
If it doesnt what will MSI add it, as I see that the KT4V does support the Sempron ?
Thanks.

>If it doesnt what will MSI add it, as I see that the KT4V does
>support the Sempron ?
Sorry, above should read as follows :
If it doesnt WHEN will MSI add it, as I see that the KT4V does support the Sempron ?

Change speed CPU-fan KT4-ultra

Does anyone know if you can change the speed of the fan on your cpu on the KT4-ultra. I tried everything with software, but nothing helps! Mayby MSI has blocked it?
Thanks.

You could try adifferent heatsink fan with a variable speed control - I use a coolermaster hac-v81 which has a speed control allowing speeds upto 5000rpm lower than 3000rpm at the bottom end.
I don't know of any mobos that allow you to control fan speed

KT4 ULTRA : CPU fan & AGP mode

Hello,
I have 2 problems :
1)Each first starting of my computer, there is 6 or 8 rings and it's written :
CPU fan isn't running? Y/N
In reality, the fan is running correctly, but it is thermoregulated.
This fan is connected to CFAN1 and I have another fan system in NBFAN1
Do you have a solution for this problem?
2)In my KT4 MS-6590 V1.0, I have the last VIA Chipset Drivers 4.51 and I have a new graghic card Hercules 3D Prophet 9600SE.
In the Bios, AGP MODE is in AUTO (grey), I can't change.
In reality, I saw it's AGP*2 or AGP*4, but not *8.
The informations in the Bios AGP Timing Control are :
AGP MODE : Auto
AGP Fast write : Enabled
AGP Aoerture Size : 256MB
AGP Master 1 W/SWrite : Disabled
AGP Master 1 W/SRead : Disabled
AGP Read Synchronization: Disabled
Can you tell me the reason why I can't affect 8 for AGP MODE
Thanks for your answer
Giro
WIN2K PRO SP4
KT4 ULTRA - MS-6590 V1.0
Hercules 3D Prophet 9600SE 128Mo (Driver Catalyst 4.1)
512Mo DDR-SDRAM

Thanks for your answers.
Richard_2003, you are right, in the control panel, it's running at 8x.
OK for the mode "AUTO" in the Bios.
For the fan, it's good like this
Giro

KT4 Ultra memory/cpu requirements

Similar Messages

Maybe you are looking for