Kt4 Ultra wont post after XP SP1 update

Hello i have had this mobo for close to 6 mths and have had no problems untill a few weeks ago. It started to intermitingly boot to no video w/2fast beeps followed by 4-8 other beeps. D-Bracket 2 shows 1.2.3.green 4.red. RTC (Real Time Clock) Just upgraded to Windows XP SP1 and now it will not boot unless cmos is cleared. But any attempt to change bios settings and reboot, gives the same problem. Even with default settings it just gives a white bar at bottom and hangs. I have taken it completly apart 4-5 times, and have tried different components (Video card, CD/DVD, PSU CPU Ram) from all my other pc's still same problem. Anyone have any ideas? Oh yeah Yes it is a legit copy of XP!!!
Athlon 1400+
Ati Radeon 9500 Pro 128 AGP
MSI Kt4 Ultra SBR
2x256 PC2100 Corsair
100GB WD Special Ed. 8MB HD
Enermax 350W 3.3V/32A 5V/32A 12V/26A
Toshiba DVD-Rom
TDK 48x CD-RW
TT Volcano 7
Fans 1 Front 1 Top 1 Rear.

Check Mobo batteries. 8)

Similar Messages

My 3gs wont restore after ios 5 update. I have tried firmware restore and restore from backup, neither works. All I get is "iphone restore failed because backup session failed" Any ideas on how to make a successful restore with this ios 5 update?

My 3gs wont restore after ios 5 update. I have tried firmware restore and restore from backup, neither works. All I get is "iphone restore failed because backup session failed" Any ideas on how to make a successful restore with this ios 5 update?

I was having the same problem, I backed up my phone and then updated to iOS 5 and then it kept telling me it could not restore from my backup as it had failed. After reading a bunch of forums and posts and trying everything, I did manage to get it to work. I had tried the Time zone, creating a new computer user account, disabling anti-virus, etc.
It took a combination of things, one of which was disabling the anti-virus completely and copying the contents of the backup folder to my desktop and then deleting everything in the backup folder. Then I rebooted the PC, entirely disabled the anti-virus, copied the one backup I wanted to restore from the desktop to the backup folder and then trying to restore. Low and behold the phone said restoring from backup and I am back in business, so when in doubt, trying combining some of the fixes together.

KT4 Ultra Users - Post here!

Please KT4 users, post here yours machine configuration, OC config and results to compare with my system.
Clock (MHz) Mult FSB (MHz) DRAM Timing
1651.5 9x 183.5 2-3-5-3-1 fast
Results:
SuperPI: 1024Kb Calculation 1:04 (64s)
Cachemem: Read: 1600Mb/s Write 820Mb/s
Cachemem download: http://www.isocdr.hpg.com.br/cachemem.exe
Thanks,
David.
[]'s

Hi. This is to let you and others know that I couldn't achieve even a 1 fsb overclock with my KT4 ULTRA-SR The system runs excellent at stock settings, but any attempt to OC was met with a no go. I am awaiting a new bios ,as my board has the original 1.o bios on it. I saw no reason to flash ,as others with the KT4 had no success with 1.1 and bigger P/S and bigger ram. I had to download the latest issue of FUZZY4 to even get it to display.on the desktop.I guess we will see if the new bios will address any issues on the KT4 boards. BIGDADDY51 :D :D ;(

Wont reboot after iOS 7 update

wont reboot after iOS 7 update

I had the same problem. Here's how it repaired. First need to note that I backed up my ios6 iphone5 to my MacBook Pro via iTunes and did the update to ios7 tethered to iTunes via USB. The iPhone hung on restart to ios7.
I disconnectd the lightning to USB chord. At that time the icon/graphic came up on the iphone screen to tell me to connect to iTunes. On reconnect, the iPhone told me that it had to be restored and that this would "wipe out" all settings and items stored on the iPhone5. So it was just like turning the iPhone 5 on new out of the box. I was good with this since I had backed up.
The iPhone 5 then went through the restore process first installing the "most recent" ios, which happened to be ios7 since that was the latest downloaded via iTunes. Once the base ios7 was installed I was then prompted to set up a new iPhone or restore from the latest backup (which I had done just prior). I chose restore from latest backup and the iPhone went through the process of resyncing to iTunes and reinstalling all apps, music, pics, video, and "others" ... a looong process.

K8n neo4 wont post after chipset heatsink replacement.

After I replaced the heatsink fan on the NB(it died recently) the machine wont post. I built it the first time, and everything is hooked up like it was before, never had any booting issues. The D-bracket gets up to the "Bios Sign On" and stays there. The screen is at the "Platinum" logo display, and neither tab nor delete get a rsponse. ANy ideas on what I did that is sticking me?

I have followed through several checklists on troubleshooting for the board(cmos battery removeal, starting up and adding one component at a time{this is where i found the no beep alarms for missing parts}, barebones start up and all tje like, and still its a no-go. I dont get any warning beeps listed for the bios, just one short beep on powerup like the board has done sence day1. The lights on the d-bracket say the same thing, Bios Sign On, I'm at a total loss, and it looks like I'm going to end up replacing the board.

Mail wont open after snow leopard update

Mail refuses to open after update,when initated it flashes in the tray then disappears,has apple a fix for this problem?
Or admits it exists.
Thanks

Mac OS X v10.6: Mail.app won’t open, or "You can't use this version of Mail…" alert after installing Security Update 2012-004:
http://support.apple.com/kb/TS4424?viewlocale=en_US&locale=en_US
Fellow user Grant Bennet-Alder offers this solution:
Some users have reported this problem if the Mail Application has been moved out of the top-level /Applications folder, or duplicated in another location.
When the Security Update is done, the old version of Mail is disabled.
The solution has been to:
1) make certain Mail is in the /Applications folder
2) There is no other copy anywhere else.
3) Once steps 1 and 2 have been done, Manually download and re-apply the Security Update (2012-004) by hand.
Security Update 2012-004 (Snow Leopard)
If the Mail.app has been LOST, it can be re-installed by applying the 10.6.8 version 1.1 combo update. But this update is quite large and it is usually not necessary:
Mac OS X 10.6.8 Update Combo v1.1

VMware wont start after latest kernel update!

Okay when i went to reboot it went to boot into arch but wile it was loading the vmware modules it would stay stuck at loading vm communication interface socket family and would just stay there the only way i could even boot into arch was to edit my grub so i could login and at least comment out vmware i tried to reapply the vmware patch fix that was on the wiki and had no luck also tried reinstalling + reapplying patch after words and still no luck I'm hoping this is happening to someone else as well and not just me (mean i know lol) I also tried virtualbox but seems it has it's own mess of problems as well after latest kernel update.

I have tried rebuilding the the kernel image and even tried reinstalling grub with no luck. After not having a usable system for several days I ended up just having to reinstall and maybe found out more about the problem. Using the net install image and a 64 bit install this time making a EXT2 boot and a root partition of JFS right after install I get a panic during boot about how the system can't find a valid filesystem on what would be root partition. Even when passing the "rootfstype=jfs" to the kernel line in grub it still errors out telling me that it is "Bailing out, your on your own. Good luck!" (pretty funny error messages if you are not ripping your hair out). After that I redid the install this time making a EXT4 root partition and everything is working.
It seems to me that this all points to a problem with JFS on 64 bit systems, my other systems are all 32 bit and usign JFS root just fine... can anyone else confirm this?
Last edited by vendion (2011-01-12 13:39:56)

Msi 790gx-g65 wont post after shtting off the night before

Tried turning it on this morning only to find out it wont post. Symptoms are....
1. Everything powers on, Fans. and all. but you cannot shut it off while holding the powerswitch in 4sec's.
only by unplugging the powersupply
2. All phase lights come on except for the #2 from the left #X###.
Only thing I can think of is it could either be the CPU of motherboard. I have already ruled out PSU Video And Memory since I took out the memory and didn't get any error codes at all, I have already done the out of the case test and reseated the CPU along with only using one stick of memory with the same exact results. this CPU worked alright but seemed to be a little on the hot side since I got it. could this be a dead CPU? HM.. I Don't know? you're opinions are greatly appreciated..thank you.

Quote from: Bas on 12-July-09, 01:00:16
You used too much compound....only a tiny drop is enough....in fact so much that you hardly see it...
It has to be that little, as without it could function better, no joke.
Only about a grain of rice give or take. Im buying a new motherboard. since the onboard video will not even work, I am confident that its the board. I have always bought MSI Motherboards but all were intel untill now. Seems that i may have gotten a faulty board. Its also been more than 30 days and I would have to send it back to msi and I doubt they would even take it back since I have put afterarket cooler on it. I'm sure they would blame me for it going bad. From the first day I seen high temps on this board, its not MSI's fault either.Thats just how things go. Maybe ill have more luck with the next board.

Z77a-g45 wont post after live update

Maybe someone could help me? I have been using this z771-g45 board for 5 months without problem, rock solid all the time. Except 4 days ago i used MSI's Live Update to update everything and after it rebooted it went into a constant restart cycle (on for 10 seconds the off) with no video, no access to anything. It had no post beeps. I let it continue for 10 minutes before I shut off the power. I have tried removing everything but the video and power to the board but still just loops. Any thoughts?

If the board is new, contact the reseller else contact MSI for rma:>>How to contact MSI.<<
If out of warrantly, you can also use a computer shop with spi programmer to get it fixed.

Safari wont start after Leopard software update

After updating Leopard to 10.5.7, Safari wont start. I get an error message "Cant load Tastyapps AV plugin." or something to that effect.
What gives? anyone know?

I was using Videobox as a trial version (on the site you have the option of buying or trying for 30 days). After the 30 days it stopped working and I just moved it to the trash. I seems to have left something in Safari however that causes it to not want to start.
Using Firefox i was able to go back to the Videobox site and download and install the trial version again. I was then given the option of installing the Safari plug in which i did. I then went to the Videobox menu and clicked on uninstall Safari plugin. and then i just moved videobox to the trash again using AppCleaner.
So, you should be able to do the same thing. Just click on "download" instead of "buy" on the Videobox site. I'm sorry, I couldnt find the plugin files for manual deletion either.
Maybe you should start a new thread and someone will know how to do that.
Thanks!

Imac wont boot after this last update

I downloaded an update (automatically through software update). After it installed it told me to wait for computer to restart and then hold power button until the long tone, then it should be done. I did that with no problem.
Ever since then though it wont boot regularly. It wither sits at grey screen forever OR gives me the prohibit sign. The only way to get it to work it to hold that power button until the long tone again.
Any idea whats wrong and how i fix it??
Thanks in advance for any help.

The long tone is an indication that a firmware update is installing. Do you get a progress bar at the bottom of you screen after letting the power button go?
Have you reset the PRAM? (cmdalt+PR when you restart the machine)
Also repair permissions when the machine is up and running.

4th gen ipod touch wont work after 6.0 update? stuck on boot screen

last night i downloaded the new os for apple. i plug it in to the comp and its in recovery mode? anyway then i install the update and restore, (that was the only option i could do) but now my ipod after restarting wont go past the boot menu, also my computer no longer recognizes my ipod any help anywhere?

Try:
- iOS: Not responding or does not turn on
- If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.

HP 8740w WH279UA wont boot after Windows 7 Updates

Hi!
Thank you all for reading my case. I'm the happy owner of a HP 8740w, I have 20GB of RAM and 500GB hard drive. My litle monster has been working perfectly for the last year and a half.
My problem began last night while I was doing a fresh Windows 7 Pro Installation, I did this after installing Windows 8.1 on the laptop and I was not happy with the overall system performace. these are the steps I run before the computer stopped working:
1. Boot from Windows 7 Pro DVD
2. Delete/Create/Format hard drive
3. Computer Boot Ok
4. Installed Wifi Driver Ok
5. Downloaded all System Drivers from HP website
6. Installed all System Drivers
7. Reboot computer it showed 107 windows Updates to be applied
8. Computer Rebooted 2 times while configuring updates
9. Computer Failed to Boot
Now every time I boot the computer the Caps Lock and Num Lock leds Blinks 3 times, according to HP Web Site the 3 times blinking leds indicates Memory Chip failure, these are the steps i tried to troubleshoot the memory error:
1. Boot the computer with the combination of the 4 memory so-dimms, failed
2. Boot the computer without memory, failed
3. Boot the computer without memory, and without hard drive, failed
4. Boot the computer without memory, hard drive, and motherboard battery, failed.
I reallt don't understand how can this had happend to my laptop. Warranty ranned out on 2013 so i'm not elegible to request a replacement. any ideas?

Hi dgonzalezln,
Your Elitebook 8740w is a commercial product and to get your issue more exposure I would suggest posting in the commercial forums. Here is a link to the Commercial Notebook forum.
Thank you,
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

After fx cc wont open after mavericks osx update

i try to open after effeects cc i get this message
when i go and open the that i downloaded from the adobe website
i get this no matter what i do it just seems not to work
any help on fixing this it would be great

Wait until tomorrow. Install the After Effects CC (12.1) update, which comes out tomorrow:
http://adobe.ly/AE_CC_12dot1_details

My ipod 5th generation wont charge after ios 8 update .. does this have something to with the charger not being an apple product?

Before the update my iPod was charging fine. then when I updated it started acting funny like one minute it would charge then it wouldn't then the next after IOS 8 came out my iPod wouldn't charge at all. could it be that my charger isn't an apple product? PLEASE HELP!!! I have important notes from school on here and I'm afraid to ask my mother for a new one without giving her a good explanation.

Could be that the update make the iPod more aware of marginal cable. Other users have reported the same.
Not Charge
- See:
iPod touch: Hardware troubleshooting
iPhone and iPod touch: Charging the battery
- Try another cable. The cable for 5G iPod (lightning connector) seems to be more prone to failure than the older cable.
- If a 5G iPod
Iphone 5 lightning port charging problem - SOLUTION!
- Try another charging source
- Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar

Kt4 Ultra wont post after XP SP1 update

Similar Messages

Maybe you are looking for