KT4AV not posting

I read all the similiar threads and I am still puzzled with my problem.
I tried to upgrade my system with a 2800+ at 333mhz. It will not post past the memory test. With the 2400+ at 266mhz it runs just fine. Could this be a power issue or a memory/CPU issue?

Quote
Originally posted by stumpy61797
BTW, PSU ratings are as follows:
+5 = 25A
+3.3 = 20A
+12 = 13A
-5 = .3A
-12 = .8A
+5VSB = 1.5A
Like I said the only thing changed is the CPU from 2400+ at 266mhz to 2800+ at 333mhz. Could running the memory at 333 vice 266 cause enough increase in power consumption to cause this?
U probably need some more amps at your 12V-rail, powers both CPU and GPU
if u could get like 18A or more it should cope.
=>bigger PSU

Similar Messages

K7n2 Delta-6570 Will Not Post

I have k7n2 delta L --6570--amdxp-2500-512 mb pc3200 ram. powmax 400w power .ati 9600 all in wonder. I swapped all parts to a better case to fit a certain location and the system will not post at all. the diagnostic d-bracket has number 1 and 4 in red while 2 and 3 are green. the book only tells me that the processor is initializing with a note saying this will show information regarding the processor (like brand name, system bus. etc. but nothing will show on the monitor. everything was working fine before the swap. i have checked everything i can think of. i would appreciate some advise. sorry if i haven't posted all the proper requrements and spec's. thanks. paul k.

i reset the memory and cpu and video card. i think i disconnected everything in the case a couple of times to make sure it wasn't a simple blunder. nothing! i have a friend that wants to try look at it i may do that. also tomorrow i will try to post all my info like the rest of you guys have done. i'll give it a try anyway. also i done the other things you mentioned, i forgot what the questions were. you can't see the post info that i am replying to keep checking so i can answer properly and i forget things.
thanks
paul k.

List of materials from the excel which are not posted

I have written bdc,
that ware house storage locations should not be allowed.
All the storage locations in the table T320 are ware house storage locations.
so i have written
if not it_data1 is initial.
SELECT * into table iT_320 FROM T320
for all entries in it_data1
where WERKS = it_data1-werks and
           LGORT = it_data1-lgort.
endif.
LOOP AT IT_DATA1 .
read table iT_320 INTO wa_320 with key werks = it_data1-werks
                                          lgort = it_data1-lgort.
IF sy-subrc = 0 .
    delete it_data1 index sy-tabix.
ENDIF.
endloop.
So its working fine till then.
but i wanted a list of materials from the excel wch are not posted,so tht the user is aware tht some items are not consumed.
How to display that list in bdc.
Please give the code for that.

MY EXCEL DATA IS IN IT_DATA1.
LOOP AT IT_DATA1 .
read table iT_320 INTO wa_320 with key werks = it_data1-werks
                                          lgort = it_data1-lgort.
IF sy-subrc = 0 .
    delete it_data1 index sy-tabix.
ENDIF.
endloop.
LOOP AT IT_DATA1 .
    MOVE-CORRESPONDING IT_DATA1 TO IT_DATA_h.
    Collect it_data_h.
ENDLOOP.
Clear it_data_h.
clear : it_data1.
THEN MY BDC IS LIKE THIS.
LOOP AT IT_DATA_H .
perform bdc_dynpro      using 'SAPMM07M' '0400'.
perform bdc_field       using 'BDC_CURSOR'
                              'RM07M-WERKS'.
perform bdc_field       using 'BDC_OKCODE'
                              '/00'.
perform bdc_field       using 'MKPF-BLDAT' LV_DATE .
perform bdc_field       using 'MKPF-BUDAT' LV_DATE.
perform bdc_field       using 'RM07M-BWARTWA' '261'.
perform bdc_field       using 'RM07M-WERKS' IT_DATA_H-WERKS.
perform bdc_dynpro      using 'SAPMM07M' '0421'.
perform bdc_field       using 'BDC_CURSOR'
                              'MSEG-WERKS(03)'.
CLEAR : FLAG1, W_FLAG.
LOOP AT IT_DATA1 WHERE aufnr = it_data_H-aufnr.
W_FLAG = 1.
CONCATENATE 'MSEG-MATNR' '(' W_FLAG ')' INTO W_MATNR_C.
perform bdc_field       using W_MATNR_C
                               IT_DATA1-MATNR.
CLEAR : QTY.
QTY = IT_DATA1-ERFMG.
SHIFT QTY LEFT DELETING LEADING SPACE.
END LOOP.
NOW HOW TO COMPARE THE MATERIALS IN EXCEL AND BDC POSTED.
PLEASE PROVIDE THE CODE FOR THAT AND HOW TO DISPLAY.

AMD Athlon XP 2800 (Barton Core) will not post at FSB 166 MHz.

Per top of the board “stickys” I have read a great number of the post on this board and done my homework to provide as much technical info to help you help me. This should explain some of it’s lengthy nature.
Aside from Memory, HDD and Video card every thing else has been unplugged from board and power or stripped out of slots to isolate the problem.
Presently running BIOS: A6712 V. 1B
*As seen on face of MoBo: KT4V MS-6712 Ver:10A
*The Original Box bar code label: KT4V-L (601-6712-050)
K7, KT400. 5.1 chnl. S/W Audio, LAN, D-Bracket 2.
CPU: AMD Athlon AXDL 2800 DLV4D
Q334763K40034 AQYHA 0447APMW
Chip lable
Athlon XP (Barton) Low Power Processor (Model 10) 2083 MHz
OPGA Organic Pin Grid Array 1.50 Volt max. Temp. 85°C
512 KB L2 Cache 333 MHz System bus (166 MHz FSB) x 12.5
Memory: x3- PC 2700 512 mb DDR 333 Super Talent
And shows at post as running 333MHz. MemTested to 1,000% with first 1 stick, then all 3 sticks presently on bios A6712vms.1B0. at fsb 100MHz (aprox. 24hr.) I even installed and ran other AMD utillitys while MemTest was running to “stress” the system memory with zero errors. During this period I checked Windows Task Manager > Performance, CPU usage at 100%, PF usage 1.35gb. No Probs.
Video card: Removed: MSI AGP-8X Ti4200- VTD8X 128 MB DDR 533MHz
Replace with: PCI card (to rule out AGP card prob.) Gilmont, nVidia 64mb
(also tried Matrox AGP 32mb card with no different results then above cards)
Power Supply: L&C Model: LC-B350 ATX = 350 watt
      115/130v      B/4a      60/50 hz
      +3.3v/+5v   1+12v   -12/-5v    +5vsb
      28a   35a    16a    0.8a    0.3a   2a
   +3.3v combined load 200w
Cooler: Slim Volcano 10+, P/N A1671, rated for up to AMD Athlon CP 3400+ & fresh heat sink compound. Freshly re-seated.
All PCI slots empty as I attempt to run bare bones to eliminate problems. (except now running Vido card in 1 slot)
Floppy Drive: ribbon unplugged from board
HDD-0: Seagate 8 gb master, (HDD tested w/no errors)
O/S: Win. XP w/sp2
HDD-1: slave/ unplugged from ribbon and power
Sony CD-Rom: Unplugged from PCI slot and power
SATA/RAID-usb 2.0 card and other HDD’s, removed and not included till Sys. runs at full potential.
Exterior HDD and Burner beyond the scope here and not attached.
O/S Win. XP-sp2
BIOS I have tried: The original; Ver:10A, ran fine on Athlon XP 1600 (1400 MP) 3 years.
•   Then with MSI Live Update 3: Installed v. 1c which couldn’t run FSB 166MHz (MSI:” Fixes system reports incorrect message for AMD 3200+ CPU.
- Supports Sempron L2 512K 3000+ CPU.)
However, v. 1.c did not work and would not post at all with the newly installed Barton AMD-XP 2800. [frankly this attempt was months ago and I do not remember whether it would post at the slower 100 and 133 FSB speeds, and also to muddle my memory further I was upgrading an A7N8X-D with a Barton XP 3000 and having similar problems on the ASUS,,, which is now running fine at full potential. ; - p
•   Then I selected and flashed A6712 V 1.7 122602, boots and runs Win.XP-sp2 at FSB 100MHz & 133MHZ. (MSI:” Supports AMD Barton XP2800+ (FSB333) CPU
-Fixes system sometimes will have IDE CRC error -Fixes D-bracket2+USB keyboard, cannot use keyboard on DOS mode.)” which couldn’t run FSB 166MHz.
I checked with the Tech. at the local shop where I purchased the KT4V MoBo. He suggested I try a different BIOS but he didn’t specify which one. He is a personal friend and admits to some bad luck and dead boards due to flashing bios so reluctant to mess with it.
•   Now running: A6712vms.1B0 – MSI hid this BIOS V. found here:
•   http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=362&kind=1
•    On a different page than the 2 versions mentioned above. http://www.msicomputer.com/support/bios_result.asp
•    No wonder people are frustrated and confused about different MoBo versions there ID #’s and the BIOS versions them selves as seen on this news board. MSI’s fault, no fault of anyone here trying to help.
A6712vms.1B0
Runs fine at FSB 100 (shows as XP 1250+) and FSB 133 (shows as XP 2200+) Booting to Win. XP-sp2 on CMOS, default setup other than minor tweaks to accommodate MSI Ti 4200 AGP 8X 125mb graphics card or Gilmond PCI card. But which couldn’t run FSB 166MHz .
No post at FSB 166 mhz (once, it did flash a post screen stating AMD Athlon XP 2800 for about 2 sec. before going blank) Manual power down. Just now I rebooted with FSB 166, and again saw the AMD Athlon XP 2800 at top of the post screen as I hit pause break,,,, then the machine power crashed to Off. Once it even loaded Win.XP-sp2 but crashed to power off with in 2 min.
I must have booted this beast a dozen times or more after Clear CMOS jumper each time it went to blank screen with mach. still running. Start over; set Default settings and work up with FSB 100, 133, each time to read what POST says and see if it will boot to O/S.
Btw: I have looked for clear evidence through the not so specific descriptions MSI uses to separate these board model #s and may be part of my current problem with correct board ID = correct BIOS ID.
Found here:
[VIA] unofficial FAQ for KT4 series motherboards
https://forum-en.msi.com/index.php?topic=6090.0
Eg: - KT4 Ultra (MS-6590), 6-channel hardware audio codec
• KT4 Ultra (Pure Version)
• KT4 Ultra-B (Bluetooth ready)
• KT4 Ultra-BSR (Bluetooth ready + Serial ATA RAID)
• KT4 Ultra-FISR (Bluetooth ready, Serial ATA RAID, Gigabit LAN, IEEE 1394)
- KT4V (MS-6712), 6-channel software audio codec
• KT4V-L, with onboard 10/100 LAN
- KT4M (MS-6596) micro-ATX board
• KT4M-L, with onboard 10/100 LAN
- KT4A Ultra, (MS-6590) NEW!! based on KT400A chipset
• KT4A Ultra (Standard Version)
• KT4A Ultra-SR (Serial ATA RAID)
• KT4A Ultra-FISR (Serial ATA RAID, Gigabit LAN, IEEE 1394)
And a very similar version of this on Official MSI site. Both seem to try and make a difference between modles with on board Lan, and Blue Tooth ready.
Take a look at my original box sticker:
*As seen on face of MoBo: KT4V MS-6712 Ver:10A
*The Original Box bar code label: KT4V-L (601-6712-050)
K7, KT400. 5.1 chnl. S/W Audio, LAN, D-Bracket 2.
Yup, it says all this on the sticker and the in the manual and verified on the MoBo. So I can only guess at all parts of the puzzle as they gave them to me which lead me to the afore mention BIOS versions I ran, or am running. The sticker points to nearly half of the boards above except for the MS-6712 and the Ver:10a which is what I based my BIOS choices on. If someone knows differently and can lead me to official Nfo with a better answer I’m all ears.
Just saw this: Latest Official BIOS : KT4 MS-6590 (1.4), KT4V MS-6712 (1.8 ) , KT4M MS-6596 (1.1)>>Here: [VIA] unofficial FAQ for KT4 series motherboards
« on: 24 October 02, 05:14:04 » But these links and all but one link in this ‘sticky’ are broken .
So if (1.8) is the Latest Official BIOS for KT4V MS-6712 then what is this at the Official MSI SITE ?
KT4V
BIOS Type
AMI® BIOS     File Sizes
485KB
Version
1.C     Update date
Update Description   -Support Sempron L2 512K 3000+ CPU.
BIOS Type
AMI® BIOS     File Size
Version
1.B     Update date
2004-8-9
Update Description   Support Sempron 2200+/2300+/2400+/2500+/2600+/2800+ CPU.
BIOS Type
AMI® BIOS     File Sizes
485Kb Version
1.A     Update date
2004-5-13
Update Description   - System is unstable to run 3DMark03 with ATI 9600 PRO
- Add "PS/2 Keyboard Detection" Function.
- Support AMD 2400+ CPU.
BIOS Type
AMI® BIOS     File Sizes
514KB
Version
1.9     Update date
2003-7-29
Update Description   -Fixed Adaptec 2100S SCSI card cannot be used
-Modify CPU temperature detection
-Support boot from Onboard LAN
BIOS Type
AMI® BIOS     File Sizes
514KB
Version
1.8     Update date
2003-2-12
Update Description   -Support AMD Barton XP3000+ (FSB333) CPU
-Add "CPU Halt Command Detection" item in the BIOS Setup
Please also keep in mind I’m not trying to scuff anyone’s shoes…I just want to get what’s right for my board so that it and the CPU can live up to their full, "as advertised" potential and run with the other 3 big dogs under my desk.
This seems descriptive enough and rather lengthy. Just doing my homework and reporting my findings so I won’t include actual CMOS settings unless requested. I have notes on all settings I currently use to boot with this problem.
Other Dogs:
ASUS A7N8X-D running Athlon XP 3000 barton core 10 (runs fsb 400..whoknew?), Mem:2.5gb Super Talent
ASUS A7M266-D running Athlon XP 2800 (mp), Mem: 3gb Super Talent
Athlon XP 2800 (mp)
I don’t want to boar you with the details.
Yes, and the above have been upgraded w/new chips GFX cards and BIOS,,, NP.
Cut to sound track: Down on the BIOS again,,, wasn’t that Creedance Clear Water Revival?
Any suggestions or insights are much appreciated.

Welcome, and thank you for a thorough input! Hope I don't miss something you already said!
Quick version: Try setting processor voltage to 1,5 volt.
Long version:
Posting at wrong FSB can be put down to two things:
1 The processor isn't what you thought it is, but I think you eliminated that.
2 The system cannot run the processor at the correct speed. Mainly this has to with overheating, and/or that memory and processor cannot cooperate. This must be it, as you noticed the processor is correctly recognised.
You have little connected right? Then the best thing would be to pull power cable out. Take the motherboard and redo the seating of the processor, this is much better done with motherboard taken out.
At the same time, I suggest you clear CMOS. Should always be done when changing processor, and I've noticed on the Internet there are a few 1,5V XP2800 around.
http://64.233.183.104/search?q=cache:Q4eIa6OhudcJ:forums.amd.com/lofiversion/index.php/t47487.html+AXDL2800DLV4D+problem&hl=sv&gl=se&ct=clnk&cd=1

MSI Big Bang Xpower II did not post - Debug LED Code #67

I need HELP...!
I have a problem my board did not post , did not start and i have the DEBUG LED CODE # 67 displayed.
There is my build
MSI Big Bang Xpower II X79 LGA2011
Intel Core i7 3820 LGA2011 Processor
Corsair Cooling Hydro Series H100 CPU Cooler System LGA2011
G.SKILL Ripjaws Z Series memory (F3-12800CL-32GBZL) DDR3 1600 PC3-12800 - CL10-10-10-30 (8192MB X 4) - 32GIG located in DIMM 1-3-5-7
Gigabyte GTX570 OC Edition video card in slot PCI-E2
Western Digital Velociraptor 300GB 2.5" SATA 3.0Gb/s 10,000 RPM
LG BH12LS35 Blu-Ray Writer 12X BD-R 16X
Ultra LSP-750 Power Supply
Cooler Master HAF X EATX Tower Case
When I put the power on, the power supply activated fans and drives spin, all the LEDs on the motherboard light up but nothing appears on the screen.
No video signal at all and the computer stop and restrart every 15 seconds. When these reset occurs there is no beep on the speaker , nothing at all, no flashing screen either, nothing.
The DEBUG LED display a sequence of flashing numbers 19 - 60 - 19- 60 - 67 and stop showing still the number # 67 for about ten seconds and then he reset again.
I carefully followed the instruction manual for the installation, I installed the memory modules in slots 1 3 5 7, i put my video card in slot PCI-E2. all the power wire are connected correctly 1 x 24 pins ATX, 2 x 8 pins ATX, 1 X 6 pins , all the wire from the front panel are correctly connected to the m-connector in JFP1 & 2.
Did i forget something, I don’t know what the debug led code # 67 exactly mean and what i have to do to fix-it
Someone has an idea what is wrong or have any suggestion to solve this issue.
Thank's all for your help.

I followed some advice to remove the memory modules and this is actually caused by the use of memory but you will see I still have a curious bug.
I referred to the instructions manual to the letter for the choice of DIMM SLOT to put the memory module in single, double, triple and quad channels.
If I install 1 memory module in the DIMM SLOT 1 to operate in single channel, everything is normal and the motherboard POST normally and show the SETUP SCREEN.
If I install 2 memory modules in DIMM SLOT 1 & 3 to run in dual channel, everything is normal and the motherboard POST normally and show the SETUP SCREEN.
If I install three memory modules in DIMM SLOT 1 - 3 - 5 to run in triple channel, everything is normal and the motherboard POST normally and show the SETUP SCREEN.
As soon as I install four DIMMs modules mémoiredans SLOT 1 - 3 - 5 - 7 to run in quad channel, the motherboard freezes and does NOT POST and show code 67 on the debug led and has reset itself every 20 seconds.
I tried all my RAM modules alternately in both single channel and everything works normally.
I did the same thing in rotation for both dual and triple channel and everything is still normal with all fourth memory modules individually.
As soon as I put a fourth memory module it freezes and displays the code 67 or L9 dependent side as you look.
So my bug is my motherboard MSI Big Bang Xpower II do not want to work in quad channel.
Do you have any idea where I should look for, is a setting in the BIOS , I have flashed the bios to the latest version V1.5
I included the screenshot of the BIOS to see if you can notice something wrong.
Thank you

Work order to cost center settlement does not post to GL module (FI)

Dear Expert,
I find the Maintenance Work order to cost center settlement does not post to GL module (FI)?Also, the settlement cost element is primary element define in GL chart of account.
When an maintenance order is settled with KO88 or KO8G the work order value posted cost center and the value is display in cost center report but not post to GL module in FI.As I notice only good issue or receive to/from work order is posted in GL but not the settlement of work order.Why?
Between, Kindly advise what are the report or T-code to view the maintenance order is done the settlement and what are the value is settle for maintenance work order?
Kindly advice under what circumstance when maintenance work order to cost center settlement is posted to GL(FI module)?
Please advice.
Thank you.
KH

Hi Kiran,
The error message clearly says that "Cost Center validity starts from 01.10.2014" i.e. in the future period.
Change the cost center from period in the past date and try.
BR, Srinivas Salpala

Invoice Parked not Posted

Dear All
Do we have a standard report where I could get the report for document is parked but not posted plant wise not Company code wise.
Or if any other option do generate this report.
Regards
Manoj

Dear Manoj,
If you assign workflow for diffrent users to complete invoice document , user automatically get the list of parked invoice in his mail box which can help you to find out the parked invoices but not posted.
If found useful reward point.
Vivek Maitra

Accounting documents are not posted for Excise invoice

Hi,
1. The Excise invoice has been created with reference to F2 invoice but the accounting documents is not posted for excise invoice, what is the settings needs tobe maintained to post the accounting entries to excise invoice..?
2. where we will maintain number ranges for excise invoice..?
Thanks
Rao..

hi
1. The Excise invoice has been created with reference to F2 invoice but the accounting documents is not posted for excise invoice, what is the settings needs tobe maintained to post the accounting entries to excise invoice..?
Not sure but can u try to relese this to accounting
2. where we will maintain number ranges for excise invoice..?
Excise invoice number range is depend on Excise series group.
T-Code : SNRO
Following is the No. Range Objects related to Excise, select the proper no. range object as per your requirement.
J_1I57FC - 57FC Number Range
J_1IARE1 - ARE1 Doc No object based on Series Group
J_1IARE3 - ARE3 Doc No object based on Series Group
J_1IBOND - Excise Bonding: Bond number object
J_1ICERT - Withholding Tax Certificates (India)
J_1ICHLNNO - Internal number range for challans
J_1ICONPLA - Consolidated PLA serial no. generation
J_1IDEPINV - Excise Invoice Number for Depot Invoices
J_1IEXCEXP - Export excise invoice number range
J_1IEXCINV - Excise invoice number
J_1IEXCLOC - Local excise invoice numebr range
J_1IEXCTST - Excise invoice with intervals
J_1IEXINEX - Excise invoice number for export
J_1IINTNUM - Internally document number to be generated
J_1IINTPR2 - Despatch serial number
J_1ILIC - Excise Bonding: License number object
J_1IPLA2 - PLA part II number range object
J_1IRG1 - RG1 Number range object
J_1IRG1_T - No. Range for RG1 - Excise group / Material
J_1IRG23A1 - RG23A part 1 no. range object
J_1IRG23A2 - RG23A part II number range object
J_1IRG23C1 - RG23C part I number range object
J_1IRG23C2 - RG23C part II number range object
J_1IRG23D - Folio Numbers for RG 23D
Check the link
Re: Excise Invoice Number Range
excise invoice and domestic invoice sharing same number range

MIRO gets posted and Part II is not posted

Dear Friends,
MIRO gets posted even if PART is not posted for excise material which create problem.
How to stop this.
Regards,
Pravin Joshi

hai,
Std SAP will copy values from PO history to MIRO screen.if you want change you can change as per your GR value.otherwise post it and do subsquent debit /credit .

Invoice verification is not posted with T.Code MIRO

Hi Friends,
1)
I created a purchase order with T.Code: ME21N, and Enter Goods Receipts with T.Code: MIGO after that Invoice verification with T.Code:MIRO, but it is not posted:
Error Message is: Error in account determination: Table T030K Co.Code: RK01 VST.
2)
Balance not zero 5000, debits 5000, credits 10000
for the second purchase order step 1 repeated.
Please help inthis regard,
thanks
ramesh.

Hi,
I think there might be some configuration missing with regard to the tax.
You ahve assign a GL account ot the TAX code for the Transaction Key VST.
Menu Path: SPRO - > Financial Accounting - > Financial Accounting Global Settings - > Tax on Sales/Purchases- > Posting - > Define Tax accounts .
Thakns
kiran

Excise duty for some line item of material document is not posted

Dear CIN Exerts,
In my Scenario user is Posting Excise invoice for every GR (105) by J1IEX to generate Excise invoice.
In some Past cases, if there are more then one line item in a GR then Excise value for some material is not showing (May be that time user not Did J1ID (Excise rate maintenance ).
Now the problem is that we wants to post excise Duty for those material WRT material document for whom it was not posted.
Please let me know that how can we do so (excise posting against Material document) so that it get reflected (for those line items for which Excise deuty is not posted) in MIGO > Document Display> Excise items tab .
Regards,
Ashutosh

Excise posting is not recommended by sap for movements 103 or 105.
Refer or search for SAP notes with subject CIN Limited functionalities.

Fixed asset Write up Error. ABZU(Parallel depreciation area 32 is not poste

Hi Sap Gurus,
      I am running into an error when trying to post a write up via "ABZU". Here is the error message "Parallel depreciation area 32 is not posted". Message no. AA565.
Diagnosis
The asset to be posted does not manage parallel depreciation area 32, or transaction type that you are using is limited to certain depreciation areas, and does not contain depreciation area 32. This is incorrect.
System Response
Posting is rejected.
Procedure
Check the asset and the transaction type.
I tried "Limit Transaction Types to Depreciation Areas" in t-code:OAXE for derpeciation area 01 and 32 but still i am getting the same error. I am using ttype:700. When i look into derpeciation tab in asset master record i have depreciation area 32 is there. Is there any configuration piece i am missing. We are using area 32 as IFRS in group which is copy of 01.
Any help will be appreciate.
Thanks and Regards,
Babu

Hi,
There are the following reasons:
1) The wrong transaction type is being used. Please verify that you are using transaction type in the 700 series for your write-up.
2) The transaction type is restricted to certain depreciation areas.   In transaction OAXE the transaction type can be restricted to post only to certain areas. If the asset manages a parallel area you have to extend the posting to include the parallel area.
3) The asset was created before you introduced parallel currencies and does not manage the parallel area. In this case, the parallel area must be created on the asset or the values need to be transferred to a new asset that manages the parallel area.
4) Transacion types 600 and 601 can only be used for assets that have a calculation key in their depreciation area that allows no automatic calculation (for example depr key MANU). The unplanned transaction types however can be used with assets that allow automatic calculation.
You also need to verify that there are entries in Table ANLB for the asset in question for the depreciation area.
5) Your company code uses parallel currencies (currency types 10-co.code currency, 50-Index based currency, 30-Group currency...for example). The assets created in this company code must have the depreciation areas for parallel currencies active. You can only do this in activating the depreciation areas with parallel currencies for all the asset classes used in this company code.
Check transaction OAYZ to make sure the areas are activated for all asset classes in the co.code. If not, you will need to       activate these areas and ensure the asset has all areas assigned.
regards Bernhard

K8T Master2-Far Will not POST unless CMOS is freshly cleared!

Hey all, thanks for helping out.
I came back to my computer one day to find it in a coma. The system was on, but the screen was getting no signal and would not come on by moving the mouse/keyboard like usual. I thought that maybe it had turned off the monitor for power save and then frooze some how. After restarting the computer I found that it was still doing the same thing. I shut down the system and unpluged. After waiting about 5 min i plugged back in and flipped the switch on the powersupply. This started the computer right up (even though i had not pushed th power button) and left it in the same condition as before. It simply would not post. After closer inspection I found that it was not posting because it wasn't getting far enough in the process before it was being restarted. I checked the restart button and even went as far as removing it from the motherboard. This did not help. I knew it was restarting because i could see it checking the optical drives then waiting for about 4 seconds, then a weird noise from the speakers (like a soft cruching so to speak) would happen, then it would do this all over again, non stop. That noise was familliar though, it was the normal noise that I hear when I push the restart button (I'm guessing a release of electricity etc..) so I knew what was going on.
After switching the memory out and in all orders, I stripped the system down to the bare min. This however did not change anything. I put the system back together and flashed the cmos. This made the system restart once, then "BEEP" it posted. It said CMOS Checksome Error - Defaults Loaded. I first pushed DEL to get into the bios. I changed everything back to how its suppost to be (time, apature, etc...) then saved and exited. This made the system go back into its restarting state. I then flashed the cmos again and pushed F1 to continue. The system booted up just fine. In safemode of course. Then i restarted. It then went back into its restarting state. I flashed the bios again. And after pushing F1 to continue selected it to go into windows normally. Everytime it does this it gets different results. One time it got past the windows xp loading screen and sat at the black screen before you get your curser and welcome screen (sigh... restart... flash..). It also once got in just fine, and after about 5 min got a blue screen about "bad pool caller". It most the time however gets a random blue screen right after you see the welcome screen. These blue screens consist of "bad pool caller", "IRQ Equal or Lesser Value", or No notes, just generic blue screen.
If i change anything in my bios it will not post. If i dont flash the cmos, it will not post. If i dont change anything in bios and continue, then restart, it will not post. The only way for it to post and for me to see anything on the screen is to flash the cmos. I thought it might be the power supply, but the only extra i have does not have the extra plug to power the 2nd cpu. After thinking about it though. I dont know if it could be a power supply issue, if it was then would it even load up into safe mode? Or why would it not load up into safe mode again after restarting. I have tried an extra stick of memory that i know works in a separate computer, but nothing changed. I have tried a different videocard... nothing changed. I have removed everthing accept the basics (motherboard, cpu's,videocard,memory,psu) and nothing changed.
I have worked on this for about 1 week now and can not figure it out. I have my useless MCSE/CSE/A+ certifications (I say useless because I dont have a job that uses them) but this one is beyond me. If anyone could help I would appreciate it.
Thanks,
Brandon
P.S. I dont know if this is related, but I did have to change from useing the DVI connection to RGB plug to even see anything once I heard it post. I was useing DVI before, and once i figured out that it would post after flashing cmos, I had to change to RGB to get any visual. The DVI will not work now at all. I have even tried changing cords. The DVI wont work in safemode either. Thanks

I reckon these mobos have a fault that really needs to be sorted. You say that your PC was working fine using PC 3200 memory with 240's. I have a similliar problem, I am using 246's with Kingston' PC3200 KVR333X72RC25/512D 2.5 ECC REG. The PC worked fine for about two weeks and then one day went on a blink, every time I power it up all I get is beeps. I was forced to order new BIOS, which didn't work everything else has been tested and works fine.
So I ordered micron memory 2X512 PC 2100 266 ECC REG which I was told by the supplier that it was compartible, that didn't work either. I then went on to check the battery, to my surprise the battery was low so I thought I had nailed it, went out bought a new battery but the problem still exits. I must say though after installing the micron memory it did boot up but when I went into BIOS to change settings to boot fro CDROM the damn thing would not restart I had to switch it off using the power button to restart it and when it restarted all i got was beeps. After that to get it to bootup I have to reset CMOS using the jumper and when it boots up it gives a checksum error message. I have a choice of two at this stage
(1) To Press F1
(2) To Press delete o go into BIOS setup
The F1 option takes me as far as the windows log on screen and that's it cuts off as if it is gonna boot itself backup but just hangs there.
The Delete option takes into BIOS which when exited the PC does nothing until powered down and powered up again, from here I have to reset CMOS to get it to bootup.
I have been told that the kingston memory is not compatible but my question is how did it work the first two weeks?
Good ol' Bas have helped out on this one quite often but here I am three months on still in a struggle. I thought of RMAing the board but it would cost me about 160 pounds and with that kind of money I could pick up another boad from kompllete.com and remain with some change for a couple of buds.
"To bass You said in the last post that the poblem could be the power supply changed it but that has not solved my problem"

Error message when posting revaluation "deprecation not posted completely"

Hi Gurus
When I am trying to post revaluation to an asset, using AR29, I get an error message APERB027 "deprecation not posted completely".
I have run AFAB for period 01/2010 and the entry in TABA is correct.
Can any one help me solve this?
Thanks
Gil

Hi
I am trying to post revaluation for 31.01.2010 (asset was capilized on 01.01.2010)
I have ran AFAR, and it didn't have any effect

Video's are missing and can not post any video's and can no longer see on Facebook after upgrading mac software. Facebook says content is unavailable. Is this a facebook issue or is there something that I can do to fix on my mac.

Video's are missing from facebook album under photo's. It shows that I have 99 and only shows 24. These are not copyright problems. I have had them up for years. Now, I can not post any video's too. Message says that content is currently unavailable. It seemed to happen after I upgraded to 10.7.5 but it could be coincidental. Of course, I have not got any email from facebook to help with this problem and I am really frustrated that I can not find my video's and post any new ones anymore. Any help would be appreciated.

I would like to add that Comcast is my internet provider. Perhaps that is part of the issue although the Connection Doctor confirms the mail box is connecting to the internet. No other function processes when Connection Doctor program is used to find the source of the issue. I have read forum posts but am unable to find a way to get my Apple mail to be delivered to my computer. It worked fine up until I chose to transfer mail to the Cloud. My mail account is a .mac account.
Still hoping someone out there can help me.
thanks,
anne

KT4AV not posting

Similar Messages

Maybe you are looking for