KT4M Backplate and Orange Power LED??

Hi
I've recently purchased a KT4m board, however it came without an MSI Stock Backplate where do I get the backplate??
Also when the machine is powered on the power LED is Orange not green as it should be how do I fix that so it is green??

The LED in my case is green but I think it's supposed to do orange when it's in standby. It was green with the old motherboard so it must be green. I modified the power LED connector so that I could plug it into either and now plugged into the two pin one it comes up green!!
I've e-mailed MSI about the backplate hope they can send me one without paying!!

Similar Messages

My router is dead and the power led is flashing the firmw...

my router is dead and the power led is flashing the firmware is corrupt i have tried everything to fix it and i cant access the web based setup

Assign a static IP address on computer like 192.168.1.10 and see if you can ping 192.168.1.1 if yes, you can try updating firmware using tftp utility.

No connection, and the power led on my router keeps blinking!!

Any help would be great!

Ok, you are not going to believe this, but I was having the same problem and now it is fixed!
First, I am no hardware guru, so for those of you who find my fix to be common sense, at least cut me some slack for trying every possible soultion :-)
First, I bought this Linksys model to replace MY EXISTING router, which I think is the W065 or something, a very good G model.
So when I hooked up the E3000, I did what evey lazy gamer does who's in a hurry.....I USED THE OLD, ALREADY CONNECTED, POWER CORD!!
Apparently, this old power cord does not provide enough power or something, because the router simply kept getting stuck in diagnostic mode (flashing power LED). it would occasionally stabalize, but only to eventually (usually inside of 5 minutes) reverting back to Diag mode and loosing all connectivity.
MORAL OF THE STORY: ONLY USE THE POWER CORD THAT SHIPPED WITH THE E3000!!
Hope this helps someone, cuz it drove me insane!!

WRT54GS wireless drop and Blinking Power-LED (V6, 1.52.5)

Hi all, Trawling several pages with people mentioning dropping wireless connectivity, I didn't notice a symptom I've noticed on mine: since the troubles started I've got the router located very close by (as in less than 3 feet/ 1 meter). One thing I happened to notice that every once in a while the Cicso loge and Power LED start blinking: connectivity is completely gone, also wired. After some time (30 sec?) the lights come on again and connectivity is restored. I haven't noticed any correlation (yet) to wireless connectivity, but it's quite irritating. Anybody any ideas?

well sounds like you have a defective device.....
tried reflashing firmware, if still not working, try calling Linksys and get an RMA #
" I can do all things through Christ which strengthens me. "

Qosmio X500 won't start and the power LED is blinks every 5 seconds

Hi,
I need help my X500 won't start now. I tried to start the NB as usual and suddenly the X500 wont boot or even power up.
If I press power button it doesnt make any sound, the power LED on button and the second power LED just bliks once and turns of, and keep blinking every 5 seconds.
I tried to:
* remove battery and power up with AC only
* power with battery only
* remove battery hold power button for 30 seconds and more athen power with AC only, battery only
but it didn't helped.
I checked the AC & Battery LEDs, but they are not flashing, they are just RED, so there is not proble in battery or AC.
Any idea where could be the problem?
Thanks for help
Frantisek

> {quote:title=FrankieCz wrote:}{quote}
> Hi,
> I need help my X500 won't start now. I tried to start the NB as usual and suddenly the X500 wont boot or even power up.
>
> If I press power button it doesnt make any sound, the power LED on button and the second power LED just bliks once and turns of, and keep blinking every 5 seconds.
>
> I tried to:
> * remove battery and power up with AC only
> * power with battery only
> * remove battery hold power button for 30 seconds and more athen power with AC only, battery only
>
> but it didn't helped.
>
> I checked the AC & Battery LEDs, but they are not flashing, they are just RED, so there is not proble in battery or AC.
>
> Any idea where could be the problem?
>
> Thanks for help
> Frantisek
hello FrankieCz
i have similar problem with my laptop
how do you solve it

Re: [Windows 10] White/Orange Power LED for GT70 2PC

Bah, I marked the wrong post as most helpful, though the one I did mark had the right suggestion so... Oh well I suppose.
Regardless, thank you! I seem to have fixed it. I went to the page you suggested then I installed the following in order
Intel Chi...

I saw another topic on this here a while back but since my experience seems slight different I thought I'd start a new thread.
My tap to click and physical click functions on the Elan touchpad just don't work at all all of the sudden. No matter what se...

PC won't boot, power LED on but, can't power up

I've tried everything and at this point I think it's my power supply.
I came home yesterday and my PC was off (it was on when I left). I noticed the power LED was on (steady, not blinking) but, none of the switches would work. I tried unplugging the PS and letting it sit for awhile and then trying it again but, again it wouldn't boot and the power LED just stays a steady green.
I only have 18amps on my +12V rail could this be the problem? See my signature for complete specs. I'm running an Antec Silent Power 350w PS (it came with my Antec SLK2650 case).
Any thoughts?
P.S. What does a solid power LED light indicate? I couldn't find info on this anywhere.

I just ran out and bought a new power supply with 26A on the +12V line. It was an Antec True 430 or something like that. Nothing happens still. The green light indicating power lights up and stays on but, nothing turns, no fans, no hard drives, nothing. I'm thinking at this point it's the motherboad ... again!
Oh, just in case I checked to make sure the board was grounded correctly everywhere and it was, I'm guessing something got shorted on the either the ATX 12V line or the bigger power line that goes to the motherboard...
Oh well, no more MSI for me guys, they just don't want to cooperate with me.

E2500 Power LED Blinking

I'm using an E2500 and the Power LED started blinking this week.
From the manual, this means   “Flashes slowly during bootup, during firmware upgrades, and druing a Wi-Fi-Protected Setup Connection.” We have a wireless printer (wireless disabled), and a Kindle that does use wireless. All other computers are hard wired. I have not started a Wi-Fi protected setup. The router has been in use since the third week in October, and is more or less OK even though the Power LED is flashing.
Why is is flashing? How do I get the Power LED to stop flashing?
Thank you.

Yes, internet connection via the router seems to be OK (both hardwired and wireless).   There may be some degradation, but I'm using a satellite provider so it may not be the router.   However, intermittant connections have occurred within the past few days and that's the same time frame at which I noticed the light blinking.  There may or may not be a correlation.
We power down all our equipment when we go to sleep (modem, router, computers etc) and power them up each morning.
The firmware version on the web site is the same as in my unit.
I do notice that when I log into the router page the light stops blinking.   When I exit the page it starts blinking shortly thereafter.

WRVS4400N Diag/Power LEDs blinking

Hey,
Recently tried to update firmware on our WRVS4400N (v1) router (from WRVS4400N_V1.0_V1.1_Firmware.zip), and ended up with router alternatively blinking the red Diag and the Power LEDs...
Googled the whole thing...and tried resetting the router (power off / on....reset button help for 60 secs +, etc)...pretty much everything most people were suggesting (including this page on the Cisco FAQ for the WRVS4400N: http://www.cisco.com/en/US/products/ps9923/products_qanda_item09186a0080a358b9.shtml - including trying with the LAN adapter speed set manually to 10Mpbs/Half-Duplex, w/Static IP address), and absolutely nothing.
So, a couple of questions:
1) Any other suggestions of what I could do...
and assuming that answer to 1 is No - what are my options? Router was bought nearly 3 years ago from a Reseller (NCIX, in Canada)...
Trying to find the information on the warranty - getting different answer - although I did see 3 yrs somewhere...can I just call in and RMA it?
Thx

Good afternoon,
The Small Business Routers typically come with three years of hardware support, including the ability to RMA if thorough troubleshooting proves the device to be faulty. However, if the tools we use determine that, based on your serial number, the product is no longer within that period, you may have to furnish a Proof of Purchase to verify entitlement.
I would highly suggest going ahead and contacting us at 1-866-606-1866 (US and Canada) with the serial number and a Cisco.com user ID so we can create you a case and troublshoot your router if it falls within the warranty period.
Thank you,
-Lindsey

MSI K8N Neo blinking power led?

Okay.. so..
I just upgraded my system with the mobo mentioned above and an AMD Athlon 64 3200+.
I wanted to test some different some different linux systems that do 64 bits.. so, first i try gentoo and then debian-amd64 (both are text based/curses based installs).
The installs go great.. but when i finish up and install X the system halts and the power led starts flashing.
I suspect that X might be pushing my power supply to the limit (for windows users.. X is a graphical interface to linux;)
So, should i go to my store and buy a new PS?
If so, can you recommend any, or any specs of the PS?
Any replies are appreciated.

You will have to make a bootable floppy with the latest bios here is MSI web page maybe this will help you http://www.msicomputer.com/support/bios_result.asp.

L655 has solid white power LED and soid orange battery LED and will not power on at all.

L655 has solid white power LED and soid orange battery LED and will not power on at all. I tried a second power adaper. Any other suggestions? It does not even try to power on. No fan or any other noises.

if it is not powering up on battery or AC, then there is either something wrong on the motherboard keeping it from powering up, or a bad power switch. I personally have not encountered a bad power switch on any of my Toshibas, so I would suspect something with the motherboard. It is strange that it does indicate that your plugged in and charging. If you leave the power adapter plugged in, does the battery status eventually go white?
Qosmio X875 i7-3630QM, 32GB RAM, OCZ SSD Qosmio X505 i7-920XM, PM55, 16GB RAM, OCZ SSD
Satellite Pro L350 T9900, GM45, 8GB RAM , Intel 320 SSD (my baby) Satellite L655 i7-620M, HM55, 8GB RAM, Intel 710 SSD (travel system)

Satellite Pro A120-151 - Won't turn on and power LED is blinking

My A120-151 shut down when I was using it. The power LED on the laptop is blinking: short-long-long-short-short-short-long-short
Does anyone know what this error code is?

There's a whole range of error codes associated with the power lights (including both orange and green flashes) They would need to be decoded by a Technician and given that it's under warranty I'd suggest it goes straight back..
The only exception to this is if you have recently changed the RAM? If so, if it is not properly seated then it can not be recognised and the laptop will fails to start.
If you have done this, try removing and *securely* reinstalling the RAM (make sure you take the battery and power lead out first!)
Nathan

Power LED Blinking Orange/White..Hardware problem?

Power LED Blinking Orange/White.
i am using a compaq cg56-102tu laptop. i wont turn on and nothing happens when i press the power button and theres a blinking orange and white light at the power indicator LED when the battery or ac adapter is connected..
courtesy of vaiost
it is like that when i plug the laptop on an outlet with or without the battery..it is the same when i only use the battery but it starts blinking when i connect the battery even without pressing any button..Any ideas?

Hello @NoGameNoLife,
I have read your post on how your notebook computer is not able to power on, and I would be happy to assist you in this matter!
Since there is a blinking orange light where the AC adapter plugs into your computer, I recommend following this document on Computer does not start and the LEDs blink or the computer beeps, as well as Using and Testing the AC Power Adapter. This should help to restore the power to your notebook.
If the issue persists, please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
I hope this helps!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Home hub 3 orange power light and speed problem

Hi, I have posted this again as I think I posted in the wrong place last time being new to the site!
Hi, I have a Home Hub 3 Version A. Orange power light constantly on.
I came across this site while looking for answers and quickly registered to post this.
I have tried all suggestions including a neighbours power supply (Version A as well) to no avail.
Background to help with replies.
I have been had option 3 since 2003.
In that time I have had
H H 1 (failed)
H H 1 replacement (failed)
Netgear – weak wireless and does not like Vodafone suresignal
H H 2 constant dropouts
Back to Netgear
H H 3 Version A lasted 24hrs
Back to Netgear.
For the last 5 months we have been having line problems, regular dropouts.
BT Openreach have been out 4 times, changed virtually everything and traced line back to Exchange.
The last engineers conclusion was line at my home is capable of 12meg and was being throttled as he called it to around 6meg.
He suggested trying a H H 3 and contacting BT for line to be opened up.
For two reasons.
With a faster speed line fault would be easier to locate.
Line was capable of so much more.
Several LONG calls to BT answering all the format questions first, (to be fair 0800 so no cost) each time first being told my speed was within contract stated speeds, then after my explanation regarding BT Openreach engineers views I was told an engineer would be contacted to improve line speed.
Needless to say nothing happened.
The frustrating point being each new call generated the same response – NOTHING on their system to show a previous call had been made by me.
Hence the reason for this post.
I feel the helpline, whilst free, achieves nothing except a long time on the phone answering repetitive questions answered before.
I am loathe to phone again as I will undoubtedly be told there is no record of any previous calls or action and I want to resolve the H H 3 Version A problem so it can be used.
Any help appreciated

Hi John46 and thanks for the reply.
Can't try H H 3 it is dead.
i saw somewhere on the forums when i first found you about a route that simplifies action from BT.
Have looked since and cannot locate it.
Do you know where it is?
With the Netgear which I have no option but to use,
ADSL on reports
Multiplex VC-BASED
VPI 0
VCI 38
Speedtester result............
1. Best Effort Test: -provides background information.
Download Speed
6667 Kbps
0 Kbps
7150 Kbps
Max Achievable Speed
Download speedachieved during the test was - 6667 Kbps
For your connection, the acceptable range of speeds is 2000-7150 Kbps.
Additional Information:
Your DSL Connection Rate :8128 Kbps(DOWN-STREAM), 448 Kbps(UP-STREAM)
IP Profile for your line is - 7170 Kbps
2. Upstream Test: -provides background information.
Upload Speed
367 Kbps
0 Kbps
448 Kbps
Max Achievable Speed
>Upload speed achieved during the test was - 367 Kbps
Additional Information:
Upstream Rate IP profile on your line is - 448 Kbps
Wall socket - tested by engineer and renewed AND RF filter fiited, just 'incase'.
Noise test also done.
Thank you for pointing me to the test, even if I had a game with Java before I could use it (New PC)!
As I read the results I am under 8meg. Openreach engineer said line was being 'throttled' as it was capable of circa 12meg this distance from the exchange. I am meant to be on 20meg contract.
Chhers,
I will watch out for a reply.
Any pointers on the H H 3 complaint route would be appreciated, i am begining to think I imagined it!!!
ps Where is the rating star? I can't see it here ?

HP Envy 15" TouchScreen Power LED shows up, but fans not running and screen does not come on

Hello there!
I am a 1A Software Engineering student at University of Waterloo, and I am running into a very serious problem with my HP Envy 15" TouchSmart laptop running Windows 8.1. This is a problem that just started today, and I would rather get some support from here first before I go see the technical support office sometime tomorrow; it has to do with the screen and fans where the Power LED lights up white, just as when the laptop is running properly.
(I do have warranty on the laptop since it was bought last June, except that if I find out I need to get a replacement, I'll lose all of my work I've been doing on it ever since I started my semester. It's so ridiculous of me to not have all of my work saved on a backup, as I do have an external hard drive. Trouble is, I got way too many problems in getting myself organized, I am not being open-minded as I should, and worst, I am not finding a balance between homework and life.)
Before I had my MATH 117 (Calculus 1 for Engineering) lecture, I was in a lab nearby where my laptop was opened and turned on, functioning properly. I had NetBeans IDE running since I wanted to work on the second part of my current CS 137 (Programming Principles) assignment. Because it was almost time for my lecture, I closed the laptop by simply moving the screen back down onto the keyboard, where it goes into sleep mode. (Anytime I flip up the screen, the laptop is supposed to come back on, and the login sliding screen from Windows 8.1 shows up.)
When I took my seat for the lecture, I wanted to spend a little bit of time to work on my programming assignment. However, upon flipping the screen back up, instead of having the login screen show up, I encountered the problem: the Power LED is showing a white light, but I can't hear the fans running from the vents on the left side of the laptop, and the screen does not turn on. I did try to hold the power button for several seconds, and once at least 10 seconds, except that the Power LED keeps on showing a white light. The light for the Wi-Fi board does not show up.
Whatever it is, I don't want to pull the battery out because I did do that on my last laptop, and it was from there that I couldn't turn the old one back on again. If I pull the battery out from the Envy laptop, it'll short-circuit the connections from the battery to the computer, and thus several components will fry. For now, what I'm doing is leaving the laptop as is to drain the charge on the battery. And then, once I notice that the Power LED does not show a white light anymore, plug the AC adapter, then try turning the laptop back on using the Power Button.
It's going to take a little while for the circuit to drain the charge on my battery though...
Anyway, would you please be so kind as to help me out with this issue? I would really appreciate it if you can give me several recommendations. Thank you!
This question was solved.
View Solution.

Hello @GregPDesWHP,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how your notebook computer is not powering on, and I would be happy to assist you in this matter!
In order to regain functionality of your computer once again, I recommend following the steps in this document on Computer does not start (Windows 8). If the issue continues after exhausting all of the steps in this document, I recommend contacting our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
I hope this helps!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

KT4M Backplate and Orange Power LED??

Similar Messages

Maybe you are looking for