KT4V won't recognize CDroms??

I had my system running perfeclty with a KT3Ultra, until one day the cdrom and burner started acting erratically. A few weeks later they completely died and I could no longer access either drive in windows; the drives were also not recognized upon POST completion. Then I noticed that my time was a few hours behind so I figured the mobo had fried and/or the cmos battery was dead.
In any case, I went out and bougth a brand new KT4V and installed it yesterday. Everything works perfectly fine, except neither the cdrom or the burner are recognized again! I have tried connecting them invidiually, with the Master setting on the drive, but they are simply ignored by the BIOS! What is this bizzare issue??? Also, if my burner is connected to the IDE then my keyboard doesn't work...!
Thanks!!
350W power supply
MSI KT4V
Athon 1800
640megs RAM
Primary IDE (no raid or any other setup, just a slave/master rig):
20gig HDD
10gig HDD
Secondary IDE:
HP burner
Kenwood CDrom
Microsoft USB mouse
Microsoft PS2 keyboard

Ok well I bought a new Antec 400W power supply and now this baby is humming like a bird with all the drives working perfectly

Similar Messages

KT4V won't recognize correctly XP2600+ (FSB 333)

Hello,
I have the following configuration:
MSI KT4V, BIOS 1.8
AMD Athlon XP2600+ FSB 333 (Tbed core as CPU-z says) BOXED version (with AMD fan)
512MB DDR400 memory (MSI recommended brand)
MSI-8888 gfx card (NVIDIA GeForce4 MX440 AGP8x)
350W psu
The problem is that after setting the FSB to 166 in BIOS, the BIOS recognizes the frequency of the CPU to be 2133MHz where on the box AMD states that the processor operates on 2083MHz. No matter what FSB number I enter, the processor speed is incorrectly recognized at 2083MHz.
Memory speed is recognized at 333MHz (which is normal, as said somewhere else in this forum) with CAS latency of 2.5.
Now, when I try to install Windows XP Pro SP1, right after the kernel initialization (during setup), I get a BSoD with error 0x0000007E (or something) and stops. I can only perform an installation if I set the FSB to 155MHz, underclocking the processor.
Now the funny thing: Windows 2000 install absolutely fine using the FSB setting to 166, where XP fail.
I tend to believe that this is some BIOS fault because of the incorrect CPUP frequency detection and the rest.
Please HELP me! Many thanks in advance.

Quote
Originally posted by wonkanoby
AXDA2600DKV3C AXDA2600DKV3D
if you set fsb to 100 what speeds it say it runs at,ie what multiplier is it using by default
When the multiplier is set to 100MHz, CPU speed is 1300MHz, so the multiplier is 13.0x -> 333MHz FSB CPU. Plus the code on the CPU is AXDA2600DKV3D.
I've done some research on the internet and the exact STOP error is 0x0000007F followed by four 0x00000000's (Division by zero, DIV). This indicates a hardware failure or a software failure or a misaligned memory (according to M$ info). Tried my parts (CPU, memory) on a Gigabyte M/B, worked fine and correctly identified so it must be a BIOS bug on KT4V AMIBIOS 1.8.
According to Micro$oft, the error also appears on overclocked systems, that go beyond CPU limits. My system runs at 2133MHz with a 333MHz FSB which means it's 2133-2083=50MHz overclocked. The problem is that I'm not trying to overclock the CPU; the BIOS configures it incorrectly and clocks it at 2133MHz instead of 2083MHz. Tried to change multiplier, but it's no avail since it's locked to 13.0x.
The only way I can install XP is by pressing F5 during the "Press F6 to select a SCSI..." message, where I select that the PC is a "Standard PC" (No ACPI whatsoever). I do not know however if I'm risking the integrity of my CPU as it's now overclocked beyond it's factory suggested frequency of 2083MHz.

ITunes won't recognize iPod Nano (1GB, 1st generation)

I have been having problems Sync'ing my iPod nano with iTunes, however, the more I read help articles and follow the steps, the worse the problem gets. (I'm on a PC using Windows XP)
I've gotten to the point where I updated my iPod software in Disk mode (up until then it was being recognized only in Disk mode), but when iTunes failed to recognize it when not in Disk mode I preceded to restore my iPod to factory settings, as instructed in the help articles.
Now, up until then, I still had music in my iPod, and I was being able to charge it and listen to my music even though I couldn't sync the iPod anymore. After restoring, I not only lost my music (which I was aware of), but it STILL did not fix my problem. So I started to get annoyed.
I then noticed that my iPod was being recognized by My Computer, just not by iTunes, so I began to perform the steps indicated in the following article:
http://docs.info.apple.com/article.html?artnum=93716
I restarted my iPod service - no luck
I removed iTunes - no luck
I emptied my Temp directory and restarted...
That's when iTunes stopped recognizing my iPod altogether, not even in Disk mode. Not only that, but it seems to have affected the iPod itself, since it won't turn off or exit Disk mode anymore. So now I'm scared of going though with any more steps on whichever "help" articles and making the problem even worse than it already is (if that's possible).
The only other information I can provide is that windows is still recognizing my iPod, no problem, and when I connect my iPod, iTunes actually launches... but DOESN'T recognize a thing. So I ran a diagnostics using iTunes and here's what I got (iPod diagnostics):
Microsoft Windows XP Professional Service Pack 2 (Build 2600)
INTEL_ D945GCL_
iTunes 7.3.2.6
iPodService 7.3.2.6 is currently running.
iTunesHelper 7.3.2.6 is currently running.
Current user is an administrator.
The current local date and time is 2007-08-30 11:53:26.
Connected Storage Devices:
Unidade de disco, MAXTOR STM3160211AS, Bus Type ATA, Bus Address [0,0]
Unidade de disco, MAXTOR STM3160211AS, Bus Type ATA, Bus Address [0,0]
Unidade de disco, Apple iPod USB Device, Bus Type USB
Universal Serial Bus Controllers:
Standard Universal PCI to USB Host Controller. Device is working properly.
Standard Universal PCI to USB Host Controller. Device is working properly.
Standard Universal PCI to USB Host Controller. Device is working properly.
Standard Universal PCI to USB Host Controller. Device is working properly.
Standard Enhanced PCI to USB Host Controller. Device is working properly.
No IEEE 1394 Host Controller found.
Connected Device Information:
IPOD (H:\), iPod nano running firmware version 1.3.1
All green lights, and as you can see, according to iTunes, NO PROBLEM! Except that it won't recognize the iPod that the disgnistics says exists and reads... ?!?!?!
If anyone could shed some light on my situation, i would be VERY greatful!

My IPod Nano will charge when connected to my computer but it won't come up on My Computer or iTunes. So I can't update the songs. I've already tried reseting the iPod. Does anybody know what I can do to fix it.

I just downloaded the latest version of iTunes on my PC, Window 8 and now it won't recognize my iPhone 4. The device never shows in the menu bar

I just upgraded to 11.1.4.62 and now my iTunes won't recognize my iPhone 4. The device never shows in the menu bar

Hello there.
The following Knowledge Base article provides some great, in-depth steps for troubleshooting your issue:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/ts1538
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Adobe won't recognize that I uninstalled CS on old computer, won't let me activate on new computer

Adobe won't recognize that I uninstalled CS on my old computer, won't let me activate it on new computer.

Yes, uninstalling is not the same as deactivating. Call support to reset activations.
Mylenium

Please Help - My iTunes library won't recognize my iPod classic

My iTunes library won't recognize my iPod classic 80gb. I try doing the trouble shooting steps on apple, but they still did not work. Any help would be greatly appreciated. I'd love to add some newer music to my old iPod for listening in the car or when travelling. Thanks a lot.

Hello dmbnewfie,
Welcome to the Apple Support Communities!
I understand that your iPod classic is not being recognized in iTunes when you connect it to your computer. I know you have tried some troubleshooting on the Apple website as well, but without knowing which steps you have completed, I would suggest working through the attached iPod classic Troubleshooting Assistant.
Apple - Support - iPod - iPod classic Troubleshooting Assistant
Have a great day,
Joe

TS3988 I changed my Apple ID to my new email address successfully for the iTunes and App store but it won't work for iCloud and it won't recognize my password. I read that this can't be done. How am I supposed to get into iCloud?

I changed my Apple ID to my new email address successfully for the iTunes and App store but it won't work for iCloud and it won't recognize my password. I read that this can't be done. How am I supposed to get into iCloud? I plan on getting rid of my old email address which is my old Apple ID so how is that going to work?

Same question Wish someone had replied!
I changed my Apple ID to my new email and now cannot find any way to access icloud. Unfortunately I had allowed icloud to hijack my airbook files, so of course I am afraid I will lose them tomorrow when I exchange my iphone for a new one and cannot keep an icloud account i cannot access. What a poor sync system! Really atypical for apple!

Deskjet 3050 won't recognize wireless network anymore.

Product: HP Deskjet 3050
Operating system: Windows 7-64 bit
Printer quit printing wirelessly. Using the control panel on the printer, I restored defaults. Now it won't recognize any wireless networks. I have unplugged computer, but that didn't help. I don't want to unplug my router, because I will lost all my DVR items (we are on AT&T uverse). Any tips?

Run a Wireless Network Test from the Network menu of the front panel. What does it say?
If everything is OK (which I suspect), re-install the printer with the temporary use of a USB cable just as you did originally when you installed it.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

HP Envy 5530 - computer won't recognize that the printer is on the same network

Product Name: HP ENVY 5530
OS: Windows 8.1
No changes made to system before issue occured
I bought this wireless printer last week (5-13-14). I have a working printer that was connected to my husband's work laptop via USB cable, but needed one to connect to our family computer, which is in a different room with the modem/router. My husband travels for work, so I want to be able to print without disturbing him and while he is away on business. I turned the printer on and connected it to my network with the password and printed out the network settings and the wireless report. There are about 8 other wireless networks in range of my printer (we're in a residential neighborhood), but we aren't having a problem with it connecting to someone elses stuff. I went online to download the driver software and it downloaded fine. I clicked on the desktop icon to launch the control panel for the printer and it opened up for me to install the printer. I went through every step and it won't recognize the IP address or the name of the printer, and therefore won't open up for me to do any scanning. Both the printer and PC are connected to the same network, but they won't recognize each other when it comes to going through the HP software to scan or print. I can go into word or something to print and it will let me print wirelessly, but it won't do anything from the control panel of the print software because it thinks the printer hasn't been installed. I've had Windows 8 on this computer since I bought it in 2012, but I have the computer defaulted to go to my desktop instead of the start screen, so I don't know if that makes a difference. I am going to go ahead and remove the device and uninstall everything so I can try again later. If I had known this was going to be a problem, I would have not bought the printer and just kept on doing what we'd been doing.

Hello SarahD_07,
Welcome to the HP Support Forums!
I understand you are having some troubles getting the Envy 5530 printing wireless on Windows 8.1. Are you able to take the I.P address of the 5530, type it into the address bar of your web browser and hit enter. Does it load a page about the printer?
Run the Print and Scan Dr to see if it can clear up the scanning issues if you can view that above page.
I will look out for your reply,
JERENDS
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

I know have a mobile me account and so my apple id is switched from my email address. i am trying to update my apps but it won't let me as it won't recognize my new 'ID'. how can i fix this on my iphone?

I have mobile me account now and so my apple id is switched from my email address to my mobile me address. Since I have made this change I can't update my apps. Everytime I try to sign in it won't recognize the switch. I have updated all the proper information on my iphone, however, when updating apps it still shows my apple id as my email address and not the mobile me account address. I am not sure what else to do??? I have even sync'd my iphone and tried to do it through my pc, however, it says that it can't update (nothing to update). I have ten updates sitting on my iphone apps...What to do...what to do? Very confused.

Where are you trying to log in? You should be able to change your ID at http://appleid.apple.com - can you log in there?
Before you change your ID you should log out of the iTunes Store and on any devices which are logged into iCloud. Then once you've changed it you can log back in with the new ID. (Your iCloud synced data will disappear from the device when you do this but will reappear when you sign back in - give it time).
If you are unable to sign into http://appleid.apple.com you will need to contact Support. Go to http://iforgot.apple.com and sign in with your iCloud login. A new password will be sent to your associated email address. If this doesn't work you will have to contact Support. Go to https://getsupport.apple.com . Click' See all products and services', then 'More Products and Services, then 'Apple ID', then 'Other Apple ID Topics' then 'Lost or forgotten Apple ID password'. If you have any problems with that try this form: https://www.apple.com/emea/support/itunes/contact.html

I plugged in my brand new nano to my husbands desktop to get it registered, but had a problem mid way through when I tried to used an apple login that already existed. Now it's not registered and the computer won't recognize my device. How do I fix this

I plugged in my brand new nano to my husbands desktop to get it registered, but had a problem mid way through when I tried to used an apple login that already existed. Now it's not registered and the computer won't recognize my device. How do I fix this?

iPod not recognized in 'My Computer' and in iTunes for Windows
Call U.S. iPod and Mac technical support: 1-800-APL-CARE (1-800-275-2273) to register your iPod Nano.

Envy 17 HDMI won't recognize mutliple displays

I've got a brand new HP Envy 17 j000 Quad Edition laptop.Device manager is showing two display adapters - one for the onboard intel HD graphics and one for the nVidia 740 GT adapter. When I try to connect an external monitor via the display port (HDMI) on the monitor, the system won't recognize it. Two questions:
Why is the internal Intel HD Graphics taking precedence over the nVidia? Typically I would set up multiple displays by this driver, but the Intel HD is the one showing the access ports - and only recognizing the internal connection and a VGA connection (which this system doesn't have).
Is there a preferred connection method - VGA/DVI/DIsplay port? I have the correct display port adapter and a new HDMI cable - both are new.
thanks - David B.

Welcome to the HP Forum David.
Below might be part of what you seek.
=====================================================================================
Here is a bit of information on the Displayport / HDMI question:
Display Port // DP-Audio-User-Guide-v1 PDF
DisplayPort.org FAQ
TechRadar.com – HDMI vs DisplayPort – which is best?
It may not directly solve your issue; it should help a bit with the background you might need to find a resolution.
=====================================================================================
Single External Monitor - that is, connect one external monitor to your computer
Sometimes the issue is simply resolution - you might therefore be able to duplicate the main computer screen, but not extend it over to the external monitor.
Resolving HDMI Display and Sound Issues
=====================================================================================
Kind Regards,
Dragon-Fur

Laptop not recognize cdrom

-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
My laptop hp pavilion dv6000 [dv6815ee], the cdrom is 'PIONEMR DVDRW'
I don't know exactly when this problem start, its from long time might 1.5 years,
i didn't try to solve the problem because i didn't have time in that time, i use
the default operation system that laptop come with[vista (86,32)],and i was
installed TrueCrypt,Ext2Fsd, also DAEMON TOOLS, MagicDisc I used them to create
virtual drive. I think the problem come after i played with these programs like
forced the virtual drive letter from disk management (from windows) to set
different letter (i think these did conflict to the programs, to the system, may
to the bios and may also between these programs daemon tools,MagicDisc,TrueCrypt,
Ext2Fsd[i use it to show my other partion ext2, i set the ext2fsd to permently
show the partions but sometimes not work well and cause hang in the system) ,also
uninstall these virtual drive from device manage, .....
first i was see my cdrom in computer with question mark i was not able to use it,
i guess the problem in that time by these programs because i played with them
settings.i created maximum virtual drive that these programs can created then i
saw the icon come normal without the question mark and i can use it normal,after
restart the problem it back,i used this method [removed virtual drive and created]
and i sucess use my cdrom,i tried solve the problem when i need it and have time,
but after it use this method three or four time it not work.
sometimes when i close the screen[the system go in sleep mode], after i open the
screen the system recognize cdrom[the cdrom after open screen go read the cd if
there].
the strange thing also i cannot boot from cdrom, i tried to change the cdrom to
check if the cdrom not work,same thing the system not recognize cdrom or show any
message occurred as a result of put different cdrom. I put my cdrom in different
laptop [same model] and it works fine.
i read in internet diffrenet cases about cdrom not recognize and cheacked many
thing like delete some keys from regestry and use programs like Mats_Run from
microsoft and programs like 'VSO Inspector',Alcohol,Nero. also i tried uninstall
Protections from the cdrom i installed different versions of SPTD
'SCSI Pass Through Direct','daemon tools'. i uninstall cdrom drive from device
manager and tried scan for new hardware, also uninstall ata/atapi controls,i reset
the DMA status of all ATA drives, delete atapi.sys,nothing work well.
I used recovery manager to restore the system to the factory default state to check if
the problem from the system, nothing happen, so i tried this time recovery without
put cdrom in the laptop after finish recovery i put the cdrom, its recognized, after
some days i played sound cd after some 2 or 3 tracks suddenly the cdrom disappear,
after that i repeated also recovery without the cdrom after that put cdrom but this
time not recognize.
I tried many thing to understand and solve the problem, i upgraded the bios before
the problem occured, i taked backup, i restore it after the problem occure, i return
upgraded to latest version. i modify settings in files[PHLASH.INI, PHLASH.AUT,
PHLASH.NOR] from HideAll=1 to HideAll=0 to show the advance options in Winphlash after
i tried options there but nothing solve the problem,
i think may the problem its related with bios specially with DMI.
[after i put different cdrom the bios in list of ordering boot i get exclamation mark
before the cdrom when the cdrom option enable, in orginaly cdrom no icons get when
enable or disable or also remove the cdrom and run the laptop without cdrom.]
i also removed the battery ant RTC battery and waited some minutes nothing happend
also the result of the log of test memory and harddisk not earsed. i tried do hard
reset but i failed
I used linux[by usb],but it's also cannot recognize the cdrom then i create dos to
boot from usb it's also cannot recognize i tried many dos drive, some of them cannot
recognize cdrom at all, others give me loop of errors and sometime hang. i tried many
programs in dos, i found program which recongize the cdrom, it show me informations
about cdrom like Model number,Serial number,Firmware revision,Peripheral device type,
Protocol type for device,Command packet size. atacd203
im sure the all cicuits of motherboard work fine but there some wrong.
i have some records of my tried in atacd203
1)-------------------------
ATAPI/CD-ROM Drive Info 2.03, Copyright (c) 1996, 1997 Dmitry V. Stefankov
All rights reserved. Disassembly or decompilation no prohibited.
.....Testing primary drive on primary controller.....
************************* Identify Device Data *********************
Model number....................... PIONEER DVDRW DR-KD08HB
Serial number...................... DDL009213WL
Firmware revision.................. 1K09
Peripheral device type ............ CD-ROM
Removable device................... yes
Protocol type for device........... ATAPI
Command packet size................ 12 bytes
Command packet DRQ type ........... accelerated (fastest=50us)
DMA supported...................... yes
LBA supported...................... yes
Disabling of IORDY supported....... yes
IORDY supported.................... yes
Overlap operation supported........ no
PIO transfer cycle timing.......... mode 2 (240 ns, i.e. 8.33 MB/sec)
SingleWord DMA transfer............ mode 2 (240 ns, i.e. 8.33 MB/sec)
Support MultiWord DMA transfer..... mode 0 (480 ns, i.e. 4.17 MB/sec)
Support MultiWord DMA transfer..... mode 1 (150 ns, i.e. 13.3 MB/sec)
Support MultiWord DMA transfer..... mode 2 (120 ns, i.e. 16.7 MB/sec)
Active MultiWord DMA transfer...... mode 2 (120 ns, i.e. 16.7 MB/sec)
Enhanced PIO transfer modes........ mode 3 (180 ns, i.e. 11.1 MB/sec)
Press 'ENTER' to continue or any other key to exit:Enhanced PIO transfer modes........ mode 4 (120 ns, i.e. 16.7 MB/sec)
Min MultiWord DMA xfr cycle........ 120 ns
Manuf/rec MultiWord DMA xfr cycle.. 120 ns
Min PIO transfer w/o Flow Control.. 240 ns
Min PIO xfr w/IORDY Flow Control... 120 ns
************************ Inquiry Device Mode Pages Data ************
Medium type code = 0x71 (door open or no caddy inserted)
.....Testing secondary drive on primary controller.....
.....Testing primary drive on secondary controller.....
.....Testing secondary drive on secondary controller.....
ATAPICD: Done.
2)-------------------------
ATAPI/CD-ROM Drive Info 2.03, Copyright (c) 1996, 1997 Dmitry V. Stefankov
All rights reserved. Disassembly or decompilation no prohibited.
.....Testing primary drive on primary controller.....
************************* Identify Device Data *********************
Model number....................... PIONEER DVDRW DR-KD08HB
Serial number...................... DDL009213WL
Firmware revision.................. 1K09
Peripheral device type ............ CD-ROM
Removable device................... yes
Protocol type for device........... ATAPI
Command packet size................ 12 bytes
Command packet DRQ type ........... accelerated (fastest=50us)
DMA supported...................... yes
LBA supported...................... yes
Disabling of IORDY supported....... yes
IORDY supported.................... yes
Overlap operation supported........ no
PIO transfer cycle timing.......... mode 2 (240 ns, i.e. 8.33 MB/sec)
SingleWord DMA transfer............ mode 2 (240 ns, i.e. 8.33 MB/sec)
Support MultiWord DMA transfer..... mode 0 (480 ns, i.e. 4.17 MB/sec)
Support MultiWord DMA transfer..... mode 1 (150 ns, i.e. 13.3 MB/sec)
Support MultiWord DMA transfer..... mode 2 (120 ns, i.e. 16.7 MB/sec)
Active MultiWord DMA transfer...... mode 2 (120 ns, i.e. 16.7 MB/sec)
Enhanced PIO transfer modes........ mode 3 (180 ns, i.e. 11.1 MB/sec)
Press 'ENTER' to continue or any other key to exit:Enhanced PIO transfer modes........ mode 4 (120 ns, i.e. 16.7 MB/sec)
Min MultiWord DMA xfr cycle........ 120 ns
Manuf/rec MultiWord DMA xfr cycle.. 120 ns
Min PIO transfer w/o Flow Control.. 240 ns
Min PIO xfr w/IORDY Flow Control... 120 ns
************************ Inquiry Device Mode Pages Data ************
Medium type code = 0x14 (120 mm CD-ROM (CD-R) Hybrid disc (Photo CD), door closed or caddy inserted)
.....Testing secondary drive on primary controller.....
.....Testing primary drive on secondary controller.....
.....Testing secondary drive on secondary controller.....
ATAPICD: Done.
3)
ATAPI/CD-ROM Drive Info 2.03, Copyright (c) 1996, 1997 Dmitry V. Stefankov
All rights reserved. Disassembly or decompilation no prohibited.
.....Testing primary drive on primary controller.....
************************* Identify Device Data *********************
Model number....................... PIONEMR DVDRW DR-KD08HJ
Serial number...................... DLL809293_L(
Firmware revision.................. 1K09 (
Peripheral device type ............ CD-ROM
Removable device................... yes
Protocol type for device........... ATAPI
Command packet size................ 12 bytes
Command packet DRQ type ........... accelerated (fastest=50us)
DMA supported...................... yes
LBA supported...................... yes
Disabling of IORDY supported....... yes
IORDY supported.................... yes
Overlap operation supported........ no
PIO transfer cycle timing.......... mode 2 (240 ns, i.e. 8.33 MB/sec)
SingleWord DMA transfer............ mode 2 (240 ns, i.e. 8.33 MB/sec)
Support MultiWord DMA transfer..... mode 0 (480 ns, i.e. 4.17 MB/sec)
Support MultiWord DMA transfer..... mode 1 (150 ns, i.e. 13.3 MB/sec)
Support MultiWord DMA transfer..... mode 2 (120 ns, i.e. 16.7 MB/sec)
Active MultiWord DMA transfer...... mode 2 (120 ns, i.e. 16.7 MB/sec)
Enhanced PIO transfer modes........ mode 3 (180 ns, i.e. 11.1 MB/sec)
Enhanced PIO transfer modes........ mode 4 (120 ns, i.e. 16.7 MB/sec)
Min MultiWord DMA xfr cycle........ 120 ns
Manuf/rec MultiWord DMA xfr cycle.. 120 ns
Min PIO transfer w/o Flow Control.. 240 ns
Min PIO xfr w/IORDY Flow Control... 120 ns
************************ Inquiry Device Mode Pages Data ************
Medium type code = 0x14 (120 mm CD-ROM (CD-R) Hybrid disc (Photo CD), door closed or caddy inserted)
.....Testing secondary drive on primary controller.....
************************* Identify Device Data *********************
Model number....................... ےےےےےےےےےےےےےےےےےےےے
Serial number...................... ےےےےےےےےےے
Firmware revision.................. ےےےے
Peripheral device type ............ unknown or no device
Removable device................... no
Protocol type for device........... reserved
Command packet size................ 12 bytes
Command packet DRQ type ........... microprocessor (slow=3ms)
DMA supported...................... yes
LBA supported...................... yes
Disabling of IORDY supported....... yes
IORDY supported.................... yes
Overlap operation supported........ yes
PIO transfer cycle timing.......... mode 255
SingleWord DMA transfer............ mode 255
Active SingleWord DMA transfer..... mode 0 (960 ns, i.e. 2.08 MB/sec)
Active SingleWord DMA transfer..... mode 1 (480 ns, i.e. 4.17 MB/sec)
Active SingleWord DMA transfer..... mode 2 (240 ns, i.e. 8.33 MB/sec)
Active SingleWord DMA transfer..... mode 3
Active SingleWord DMA transfer..... mode 4
Active SingleWord DMA transfer..... mode 5
Active SingleWord DMA transfer..... mode 6
Active SingleWord DMA transfer..... mode 7
Active MultiWord DMA transfer...... mode 0 (480 ns, i.e. 4.17 MB/sec)
Active MultiWord DMA transfer...... mode 1 (150 ns, i.e. 13.3 MB/sec)
Active MultiWord DMA transfer...... mode 2 (120 ns, i.e. 16.7 MB/sec)
Active MultiWord DMA transfer...... mode 3
Active MultiWord DMA transfer...... mode 4
Active MultiWord DMA transfer...... mode 5
Active MultiWord DMA transfer...... mode 6
Active MultiWord DMA transfer...... mode 7
Exp. time to release (cmd rcvd).... 65280 ns
Exp. time to release (srvc cmd).... 65280 us
Major version number (std)......... 32640
Minor version number (std)......... 65280
************************ Inquiry Device Mode Pages Data ************
Medium type code = 0x8 (80 mm CD-ROM Hybrid disc (Photo CD), door closed or caddy inserted)
.....Testing primary drive on secondary controller.....
.....Testing secondary drive on secondary controller.....
ATAPICD: Done.
these the records if i use atacd203 with debug option:
1)-----------------------
ATAPI/CD-ROM Drive Info 2.03, Copyright (c) 1996, 1997 Dmitry V. Stefankov
All rights reserved. Disassembly or decompilation no prohibited.
.....Testing primary drive on primary controller.....
!!! Task file hardware found for base=0x1F0, drive=0
---Get ATAPI Identify Device data---
Status reg=0x41 (BSY:0,DRDY:1,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
>>>Send ATAPI Identify Device command<<<
---Wait while drive is busy ---
Status reg=0x41 (BSY:0,DRDY:1,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
--- Polling method in use ---
Status reg=0x41 (BSY:0,DRDY:1,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
Error reg=0x4 (MCR:0,ABRT:1,EOM:0,ILI:0;sense key->successful command)
-> ATAPI Identify Device command failed (no data from device).
Status reg=0x41 (BSY:0,DRDY:1,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
>>>Send ATAPI Soft Reset command<<<
Status reg=0x41 (BSY:0,DRDY:1,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
---Get ATAPI Identify Device data---
Status reg=0x41 (BSY:0,DRDY:1,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
>>>Send ATAPI Identify Device command<<<
---Wait while drive is busy ---
Status reg=0x41 (BSY:0,DRDY:1,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
--- Polling method in use ---
Status reg=0x41 (BSY:0,DRDY:1,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
Error reg=0x4 (MCR:0,ABRT:1,EOM:0,ILI:0;sense key->successful command)
Press 'ENTER' to continue or any other key to exit:-> ATAPI Identify Device command failed (no data from device).
.....Testing secondary drive on primary controller.....
!!! Task file hardware found for base=0x1F0, drive=1
---Get ATAPI Identify Device data---
Status reg=0x1 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
>>>Send ATAPI Identify Device command<<<
---Wait while drive is busy ---
Status reg=0x1 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
--- Polling method in use ---
Status reg=0x1 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
Error reg=0x4 (MCR:0,ABRT:1,EOM:0,ILI:0;sense key->successful command)
-> ATAPI Identify Device command failed (no data from device).
Status reg=0x1 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
>>>Send ATAPI Soft Reset command<<<
Status reg=0x1 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
---Get ATAPI Identify Device data---
Status reg=0x1 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
>>>Send ATAPI Identify Device command<<<
---Wait while drive is busy ---
Status reg=0x1 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
--- Polling method in use ---
Status reg=0x1 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
Error reg=0x4 (MCR:0,ABRT:1,EOM:0,ILI:0;sense key->successful command)
Press 'ENTER' to continue or any other key to exit:-> ATAPI Identify Device command failed (no data from device).
.....Testing primary drive on secondary controller.....
!!! Task file hardware not found for base=0x170, drive=0
.....Testing secondary drive on secondary controller.....
!!! Task file hardware not found for base=0x170, drive=1
ATAPICD: Done.
2)----------------
ATAPI/CD-ROM Drive Info 2.03, Copyright (c) 1996, 1997 Dmitry V. Stefankov
All rights reserved. Disassembly or decompilation no prohibited.
.....Testing primary drive on primary controller.....
!!! Task file hardware found for base=0x1F0, drive=0
---Get ATAPI Identify Device data---
Status reg=0x41 (BSY:0,DRDY:1,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
>>>Send ATAPI Identify Device command<<<
---Wait while drive is busy ---
Status reg=0x41 (BSY:0,DRDY:1,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
--- Polling method in use ---
Status reg=0x41 (BSY:0,DRDY:1,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
Error reg=0x4 (MCR:0,ABRT:1,EOM:0,ILI:0;sense key->successful command)
-> ATAPI Identify Device command failed (no data from device).
Status reg=0x41 (BSY:0,DRDY:1,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
>>>Send ATAPI Soft Reset command<<<
Status reg=0x41 (BSY:0,DRDY:1,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
---Get ATAPI Identify Device data---
Status reg=0x41 (BSY:0,DRDY:1,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
>>>Send ATAPI Identify Device command<<<
---Wait while drive is busy ---
Status reg=0x41 (BSY:0,DRDY:1,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
--- Polling method in use ---
Status reg=0x41 (BSY:0,DRDY:1,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
Error reg=0x4 (MCR:0,ABRT:1,EOM:0,ILI:0;sense key->successful command)
Press 'ENTER' to continue or any other key to exit:-> ATAPI Identify Device command failed (no data from device).
.....Testing secondary drive on primary controller.....
!!! Task file hardware found for base=0x1F0, drive=1
---Get ATAPI Identify Device data---
Status reg=0x1 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
>>>Send ATAPI Identify Device command<<<
---Wait while drive is busy ---
Status reg=0x1 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
--- Polling method in use ---
Status reg=0x1 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
Error reg=0x4 (MCR:0,ABRT:1,EOM:0,ILI:0;sense key->successful command)
-> ATAPI Identify Device command failed (no data from device).
Status reg=0x1 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
>>>Send ATAPI Soft Reset command<<<
Status reg=0x1 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
---Get ATAPI Identify Device data---
Status reg=0x1 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
>>>Send ATAPI Identify Device command<<<
---Wait while drive is busy ---
Status reg=0x1 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
--- Polling method in use ---
Status reg=0x1 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:1)
Error reg=0x4 (MCR:0,ABRT:1,EOM:0,ILI:0;sense key->successful command)
Press 'ENTER' to continue or any other key to exit:-> ATAPI Identify Device command failed (no data from device).
.....Testing primary drive on secondary controller.....
!!! Task file hardware not found for base=0x170, drive=0
.....Testing secondary drive on secondary controller.....
!!! Task file hardware not found for base=0x170, drive=1
ATAPICD: Done.
3)-------------------------------
ATAPI/CD-ROM Drive Info 2.03, Copyright (c) 1996, 1997 Dmitry V. Stefankov
All rights reserved. Disassembly or decompilation no prohibited.
.....Testing primary drive on primary controller.....
!!! Task file hardware found for base=0x1F0, drive=0
---Get ATAPI Identify Device data---
Status reg=0x51 (BSY:0,DRDY:1,DF:0,DSC:1,DRQ:0,CORR:0,D1:0,CHK:1)
>>>Send ATAPI Identify Device command<<<
---Wait while drive is busy ---
Status reg=0x51 (BSY:0,DRDY:1,DF:0,DSC:1,DRQ:0,CORR:0,D1:0,CHK:1)
--- Polling method in use ---
Status reg=0x51 (BSY:0,DRDY:1,DF:0,DSC:1,DRQ:0,CORR:0,D1:0,CHK:1)
Error reg=0x4 (MCR:0,ABRT:1,EOM:0,ILI:0;sense key->successful command)
-> ATAPI Identify Device command failed (no data from device).
Status reg=0x51 (BSY:0,DRDY:1,DF:0,DSC:1,DRQ:0,CORR:0,D1:0,CHK:1)
>>>Send ATAPI Soft Reset command<<<
Status reg=0x0 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:0)
---Get ATAPI Identify Device data---
Status reg=0x0 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:0)
>>>Send ATAPI Identify Device command<<<
---Wait while drive is busy ---
Status reg=0x51 (BSY:0,DRDY:1,DF:0,DSC:1,DRQ:0,CORR:0,D1:0,CHK:1)
--- Polling method in use ---
Status reg=0x51 (BSY:0,DRDY:1,DF:0,DSC:1,DRQ:0,CORR:0,D1:0,CHK:1)
Error reg=0x4 (MCR:0,ABRT:1,EOM:0,ILI:0;sense key->successful command)
Press 'ENTER' to continue or any other key to exit:-> ATAPI Identify Device command failed (no data from device).
.....Testing secondary drive on primary controller.....
!!! Task file hardware found for base=0x1F0, drive=1
---Get ATAPI Identify Device data---
Status reg=0x0 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:0)
>>>Send ATAPI Identify Device command<<<
---Wait while drive is busy ---
Status reg=0x0 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:0)
--- Polling method in use ---
Status reg=0x0 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:0)
Error reg=0x0 (MCR:0,ABRT:0,EOM:0,ILI:0;sense key->successful command)
-> ATAPI Identify Device command failed (no data from device).
Status reg=0x0 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:0)
>>>Send ATAPI Soft Reset command<<<
Status reg=0x0 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:0)
---Get ATAPI Identify Device data---
Status reg=0x0 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:0)
>>>Send ATAPI Identify Device command<<<
---Wait while drive is busy ---
Status reg=0x0 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:0)
--- Polling method in use ---
Status reg=0x0 (BSY:0,DRDY:0,DF:0,DSC:0,DRQ:0,CORR:0,D1:0,CHK:0)
Error reg=0x0 (MCR:0,ABRT:0,EOM:0,ILI:0;sense key->successful command)
Press 'ENTER' to continue or any other key to exit:-> ATAPI Identify Device command failed (no data from device).
.....Testing primary drive on secondary controller.....
!!! Task file hardware not found for base=0x170, drive=0
.....Testing secondary drive on secondary controller.....
!!! Task file hardware not found for base=0x170, drive=1
ATAPICD: Done.
i get some hope to solve the problem after i saw the Announcements of ask Expert day
-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=

I believe the problems is not with the hard drive or the CD/DVD ROM, but what is on the hard drive that is keeping the OS from recognizing the ROM.
If I am reading the posts correctly I think you have tried enabling the CD/DVD -ROM in the BIOS. Is that correct ?
Use Partition Wizard to delete and merge any partitions that were not shipped with the laptop. With Vista there should be recovery and the OS partition and nothing else. Other partitions containing additional OS's can cause Vista not to recognize the CD drive.
http://www.partitionwizard.com/free-partition-manager.html
Ounce you have cleaned up the hard drive, if the CD drive is still not recognized, try reinstalling the drivers for the CD/DVD ROM in the device manager.
If that does not work, try performing another system restore with the recovery partition, maybe with the hard drive cleaned up with Partition Wizard it will reinstall Vista correctly to recognize the CD drive.
Another thing to do is to create a system recovery loaded on a USB flash drive. Your specific model was not coming up with the info. you have given so here is the instructions for a dv6000 cto. They are the same.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01890478&tmp_task=useCategory&lc=en&dlc=en&cc=u...
Still another option is to remove the hard drive and connect it to another computer through USB and delete everything on the hard drive and create unallocated space. Reinstall it back into the laptop and with nothing on the hard drive the BIOS may recognize that you can boot from the CD/DVD ROM drive. With that you will be able to recover your system back to Vista and of course you will have to order some recovery disk's from HP.
Any of the above procedures are experimental and I can not guarantee if they will work, they may make things worse.

My I-cloud says I have no devices set up even when i'm logged in to my apple , how do I fix this problem? Please respond quickly, I lost my ipod and even when I try to place it in lost mode it still won't recognize that I have a device. What do I do?

My I-cloud says I have no devices set up even when i'm logged in to my apple ID account, how do I fix this problem? Please respond quickly, I lost my I-pod and even when I try to place it in lost mode it still won't recognize that I have a device. What do I do?

If you did not set up find my iPhone on the iPod, you can't find it.

2 things: iPhoto isn't automatically copying all my imported photos into an iPhoto album folder AND ever since i upgraded my MacBook 120GB to Snow Leopard, iTunes won't recognize my iPhone.

So i have a 120GB MacBook that's about 4 years old (just updated to Snow Leopard--been working in Iraq, i'm a little behind).
Never had a problem with it.
I also have an iPhone 4 which i've had for about a year (up-to-date software as of about a month ago).
Never had a problem with it.
I've had iTunes for years of course (up-to-date).
Never had a problem.
1.
Now my iTunes won't recognize my iPhone since the Snow Leopard update.
iPhoto will recognize my phone, but iTunes won't.
Went through all the preferrences and i can't find anything that isn't set properly.
iTunes Helper is used during startup.
Everything seems fine.
Any help?
2.
I use a WD external hard drive to back my Mac up every week or so.
I recently realized that half of my pictures from iPhoto are not copied to the external.
They haven't been transfering over.
So i snooped through my folders and as it turns out, iPhoto hasn't been copying the pictures i import from my iPhone to iPhoto and saving them as .jpg files in the pictures folder (or iPhoto album or whatever) like i think it's supposed to.
My pictures folder has approx half of all my pictures in it, meaning at some point (probably 2 years ago) iPhoto stopped making the file copies of my imported pictures.
I do not know why.
No idea how to fix it.
If i were able to fix that (with your help), would all the pictures that haven't been copied automatically copy to my pictures folder once i had the issue resolved or would there be a lot of dragging and dropping?
I've been clumsily and sloppily copying all my pictures to a new folder on my desktop and manually transferring that folder to a thumb drive (which i keep in my pocket) and my external (just so i have them in some form) in case my computer crashes or a mortar shell lands on my room and blows my computer up.
Can anyone please help me with any of this?
I can't just stoll down to the Apple store to ask the Genius Bar (I'm in Baghdad) and i don't have Apple Care so no one will help me on the phone when i call Apple.
Thanks so much.

hey mill1640,
Did you ever get your iPhone to register with iTunes? I just upgraded as well to Snow Leopard, and my my isn't recognized at all also.
If you did get this resolved, I would appreciate a little suggestion in the right direction.
Many thanks,
Josh

KT4V won't recognize CDroms??

Similar Messages

Maybe you are looking for