KT6V-FISR Boot Problem

I have just bought a new processor, and motherboard.
when I set the cpu fsb to 200 mhz bios displays Atlon 3000 but the machine hangs with a blank screen after post.
If I set the 166 mhz the cpu is picked up as being a Atlon 2400 and the machine will boot into windows.
I have tried different memory, but is still the same.
Do you think that I got a flaky processor?
Thanks
Specs.....
Athlon 3000+ XP 400 fsb
MSI K6T Delta-fisr
2 x 512 DDR 333 (Generic)
Geforce Ti42000 128 meg
500 Watt Power Supply
S/B Audigy
Temps
CPU - 49c
SYS - 39c
Voltages
Vcore - 1.68v
3.3v - 3.41v
+5 - 5.15v
+12v 12.20v
mem - 2.50v

I have so many thumbs I type very fast. Also know, because I have been baby-sitting so much, you always must let young people win one way or the other. :hypecrite:
EDIT:
Meaning of DOLLOP
Pronunciation: 'dâlup
Definition: [n] a small measure (usually of food)
See Also: small indefinite amount, small indefinite quantity

Similar Messages

KT6V Weird boot problems

Hi..
I'm having this weird boot problem (and no it doesn't seem to be the standard one)
OK..
I have the following :
AMD Athlon 2000+
KT6V LSR mainboard
2x 256 Crucial PC2700 memory
IDE Hard Disk (120gb segate)
Creative 5700ultra Graphics card (AGP)
Cd Rom
Chieftec 400w PSU
WinXP Pro
If I set my CPU FSB to 100mhz (everything else on auto).. win Xp pro boots fine and all is pretty good except that my chip is now seen as a lowly 1.25ghz..
If I then set my CPU FSB to 133 or 166 then the machine boots (ie it beeps etc..).. starts to load windows xp (I get the logo and that's when the problem happens) and either black screens (ie.. nothing and the monitor turns off) or blue screens with the windows message saying that windows has detected a hardware fault and has halted the system..
I know my memory, chip, heatsink etc all work because just over an hour ago they all worked fine in my KT3 ultra.
What is going on as I've tried almost everything to try and solve this, with the only option to set the FSb to 100mhz which is incorrect for my CPU.
How do I fix this.
I've looked through the forum but this is not the same problem as simple reboots.. this is weird.
If I can't fix this then I guess it'll be send it back.. which is a shame because I like MSi motherboards.
Thanks
Slippery

Hi..
I've checked the CPU heatsink.. and nothings wrong !
(Can't check the voltage but I know the PSU is Ok as I did run it in a custom case with 4 Cd writters, 4 HDs, loads of lights etc.. before I moved to this new plain case tonight)
What's weird is that set at 100FSb it's fine but at 133 or 166 it just crashes after the loading XP logo is displayed. Up until that point it's all fine.
But why does it run Ok at 100mhz and not 133mhz ?
Please help.. before I end up fixing this with a hammer !
Thanks
Slippery

KT6v-LSR Boot Problems

I'm only giving the specs for certain items because I'm only trying to boot it with these installed.
KT6v-Lsr
AMD XP 2400+ T-bred
Thermaltake Volcano 6 cu+
Antec 430 Watt PSU (+5v=36a, +12v=20a, +3.3v=28a, -5v=.5a, -12v=1.0a,+5vsb=2a)
I've been having this problem since I bought this board and put it together earlier this week. I first tried to power the system with my old Antec 300 Watt psu. When I read the other posts on this board I went out and bought a 400 watt psu, same problem. I finally went out and bought a better Antec 430 watt psu, still same problem. Please help. This is what happens when I try to boot up (same problem, all psu's) the D-Bracket leds show Sys Power ON, then Early Chipset Initialization, then Memory Detection Test... and then the system powers down. I would think that with 20a on the 12v I would be set, so I'm starting to think the mobo is just bad, and might just return it. Would appreciate any help though.

In fact, feel grateful that the newer boards have the ability to detect the CPU temp rising too fast, and shut the system down to save that costly CPU's life
Without that little feature, you could fry a CPU in just a couple minutes

KT6V-LSR boot problem

I encounter a strange problem(which I think is because of main board):
- Sometimes when I press the power on button(to power on the system),then the system don't really starts, only the HardDisk(red) LED is ON, the PowerOn(green) LED is OFF. The monitor remains black, with a LED blinking.
- While the system is in state described before, if i press the Reset Button, then: the PowerOn(green) LED turns ON too,the monitor receives signal(it's LED stops blinking, by remanining ON), and the system starts OK(everything is ok).
What can be the problem?
the system configuration is:
- MSI KT6V-LSR, SocketA, AMD Athlon & Athlon XP & Duron 550MHz- 2+GHz, VIA KT-600 chipset, 266/333/400 MHz FSB, 3 DDR DIMM max. 3 GB, PC3200/2700/PC2100, PC1600 DDR SDRAM, 5PCI, 1AGP 8x, 2 UDMA66/100/133 Bus Master IDE, 6USB 2.0, 1P/2S, PS/2 bill/egér, ATX, AC 97 6 ch. Audio
PC Cillin 2000 vírusírtó szoftver, Serial ATA !!!!, RAID, LAN
- AMD XP 2600 Palomino 2,07G 333Mhz
- 256MB 400MHz Brand PC-3200
- AGP nVidia GeForce FX5200 128MB DDR TV-OUT
- 80Gb Maxtor IDE 7200rpm Cache: 2MB ATA/133
- Cooler socket A 3.2 GHz
- Midletower RJA 217 4bay ATX/P4 400W SILVER+BLUE

Hello,
Did you build this PC or did someone else build it?
Open the PC, remove the case side panel and check the JP1/case connectors.
Check if the power switch, reset switch, hdd LED are Power LED are plugged in the right place.
The best way to do this is to remove all the case connectors and start again, plug 1 at a time and see if it works better.
Start with the front case power switch first, plug it in and see if the PC starts when you press it.
Make sure the PC is off when you do this, (turn on when you are ready to test).

K7N2 Delta-L: Strange cold boot problem & solution

My K7N2 Delta-L has a problem cold booting when the vcore is set in the bios at 1.65v of higher. After a cold boot, you get a blank black screen. I noticed that even if you run at default speeds but set the vcore to 1.65v of higher the problem still occurs. There is no problem rebooting however.
I found the following solutions:
1. After you power up and get a blank, hit the reset button.
2. Don't unplug your PC. My PC is connected to a AVR and after I power down the PC I usually turn the AVR off. If i do this, than the computer will have a booting problem if I try to boot it up 30 minutes later or so. Now if I don't unplug it/power off the AVR than everything is fine.
I don't understand why it acts the way it does though.
Does anyone know of any other solutions?

Have you cleared the cmos. If you do be sure you have the power turned off don't move the cmos jumper with the power on.
I found that turning off power at power supply and unpluging, than turning on the computer the fans will spin just a little this drains all the power. Clear cmos 2-3 than return to
1-2 position.
Than plug the power back in and turn it back on, than try the computer again.

Mid 2006 iMac Boot Problem (Since latest firmware update)

I have a Mid 2006 17" iMac. Ever since the latest firmware update in early December, about every other startup I've been having boot problems. After the white screen with the Apple Logo and the spinning wheel it goes to a blue screen like normal, but instead of the 'Loading Mac OS X' white window popping up it stays blue and the spinning loading wheel starts. I've left it loading for quite a while before and nothing changes. I have to do a force shut off by holding the power button. and then I start it up and it will boot normally.
Any help would be appreciated.
Thanks!

Actually, I think it'san early 2006.

1st series iMac G5: Booting problems, kernel panics, waking from sleep...

Specifications of the iMac described: 1.8 Ghz, 1GB, 80GB, 64 Mb Nvidia VRAM, Airport, 10.5.5
Back in August 2004 my dad bought us kids an iMac G5 for ‘family use’. It had a fresh install of 10.3.5 on it and compared to the (1999) iMac G3 it replaced it was amazingly fast.
The iMac never showed any signs of probable issues, until we decided to upgrade to Leopard in January 2008. Initially, this upgrade was only meant to be able to sync with the latest iPod nano (who demanded a newer version of iTunes).
After the installation the first thing I noticed was a high CPU usage, the machine seemed slower than ever and that with 1 Gb of RAM (the minimum sys. req. for Leopard are 512 Mb of RAM). Anyway, then the real thing started, it wouldn’t turn on anymore. We brought it to an Authorized Apple Reseller, the Tech department said the Logic board had failed. The costs of the fix weren’t the worth the computer anymore, so...end of story. The iMac was indeed one of the bad series, although it hadn’t any swollen capacitors.
My dad already made up his mind and bought himself a Macbook. He then told me that if I was able to get the broken iMac fixed, I could keep it. And so, I bought an ‘as-is’ logic board on Ebay. Last weekend I installed it, and it actually seemed to work! Yet, the problems are during the startup: the first thing I see is a screen full with horizontal lines flickering all the time, like an old TV with bad signal. Mostly it won’t boot and I get the message to restart the computer (kernel panic, I got dozens of logs already!). Sometimes it got stuck during booting (grey apple screen with gear in the middle) making the fans go crazy (after a while) and sounding what others describe as a ‘jetliner taking off’ sound. Sometimes the screen remains black. Generally it takes me 5 to 10 minutes to start up properly. Maybe it’s just me but it seems like when the computer has warmed up a little (by turning on and off on and on) starting up gets smoother. I mean the startup screen suffers from less horizontal flickering lines.
During the use of Leopard, I again get high CPU usage, especially when I use multiple programs at the same time, or when starting multiple programs. My iStat Pro said once that the fans were running at 4700 rpm and the heat of the CPU was about 70 Celsius. If I really want to **** my iMac off I should play a racing game. That just totally freaks him out! These problems could probably be solved by adding more RAM. Right?
The iMac also has a sleep problem. Sometimes after lets say an hour or so, you can’t get it out of sleep mode (by manipulating keyboard and/or mouse, the sleep light stops, but the screen stays off --> only solution is to restart). What happened to me once was that it slept so long that it just got into a deep sleep by turning itself off completely!
Here’s a list of what I tried so far:
- Disk Utility: Resetting the permissions, no problems were found.
- Resetting the SMU, both on the logic board itself as by pressing the power button 5 - 8 seconds, no improvements.
- Resetting the PRAM, no improvements.
- Did the Hardware test of the original install CD, nothing was found, all good.
- Did Archive and Instal, this actually messed my system entirely, cause it wouldn't boot at all and when starting up from the Leopard installation DVD it wouldn't recognize the Macintosh HD.
- Did Archive and Instal with the original disks, this disk did recognize Macintosh HD and so I installed the original system, 10.3. Booting problems and those flickering lines are still there though.
Next phase will be erase and install, but first I want to know what you guys think about all this.
Oh eh, One more thing; The guys at Applecare (phone support) told me that the replaced logic board was also out of warranty and so they couldn’t help me. But as the man on the phone was kind, he told me to go look for a special ‘driver’ on the net. He said that the driver should be able to resolve some of the issues described. He said that I had to give in the name of the LB on google and look for results. Is this bogus? Because I haven’t found anything useful on google so far. What’s the name (rather than a number) of the LB in the first place?
I hope you guys can give me some answers. I'm kinda desperate. But I still feel there's hope...

The symptoms of a flakey power supply are sleep problems and you have done all the right things as far as resetting the SMU and PRAM. Your CPU usage can be tracked by going to Utilities>Activity Monitor - look and see what is hogging the memory. The flickering lines could also be an optical system going south.
The other thing you can do is run DiskWarrior or TechToolPro to see if you have corrupted directories. Preferential Treatment will let you check for corrupted preferences.

MSI P45 Neo-f with intermittent boot problems

Current system:
*CPU: Intel core2duo 4300 1,80GHz
Mobo: MSI P45 Neo-F LGA775
*Memory: 1 Kingston 1GB PC2-5300 667MHz DDR2 and 1 Dane-Elec 1GB PC2-5300 667MHz DDR2
Videocard: Club3D Nvidia 8800GT 512MB GDDR3
*Hard drive: 120GB IBM deskstar 7200rpm Ultra-ATA/100 (yes I realize it is known as the deathstar, but it hasn't failed so far, I do back-up because I'm paranoid
PSU: Real Silent Nexus NX-5000 500 watt
*Soundcard: Soundblaster Audigy
OS: Windows XP home, service pack 2
*Lite-on IT dvd-rom drive
*floppy disk drive
I also have 3 case fans spinning away in a marginally large Chieftec Dragon tower.
The parts I marked with an asterisk (*) are parts that I removed from my old rig and re-used.
I'll try to give a clear rundown of my problem and the steps I've taken so far.
3 days ago I acquired the P45 Neo and installed it into my system, together with the 8800GT videocard. I was still using my old PSU, a Chieftec 360watt. This PSU served me well for 7 years, but it was starting to build up noise while trying to keep up games on my old rig.
I had some trouble getting the system to boot, I tried changing some of the 4 pins wires going to the hard drive and the dvd drive. I don't know if it was luck or if I managed to divide the load properly for the system to boot. But I succeeded into booting up, got into the bios and eventually installed WinXP.
As soon as it was time to install the videocard drivers, it stopped responding. I assumed it was a power issue, since I could only install the 20pin and 4pin cpu, but my Chieftec PSU didn't have a 24pin plug to the mobo - and it needed replacing anyway! So I bought a new 500watt PSU that had all the required plugs and more wattage.
I installed the new PSU, checked every connection and pressed the power button. 'Lo and behold, the computer starts up. I install the videocard drivers and it proceeds with no problems. I try to install the soundcard, but the cd says I don't have one installed. I fix that by going to the System list and install the drivers from there. I install a firewall. By then I have successfully rebooted the computer 3 or 4 times. I decide all is well and turn off the computer. But I realize I wanted to check up something on the internet.
I press the powerbutton. The PC power light go up for just a fraction of a second. I can see the blue LED of one of the case fans switching on just as briefly - then it goes out. The computer keeps trying to turn itself on. It looks like it's hickupping to try and boot!
I turn off the PSU power on the back-side because the computer keeps trying and wait for a bit. After 10 minutes, it still doesn't work. I leave the computer for a bit and return an hour later. The computer then starts up with no problems. I turn it off after a few hours, do a reset, start it up, no problems. But then the next day it happens again.
It's pretty tough figuring out what the problem is because it looks..almost random. I considered it could be a heat issue, but sometimes it *does* start up just after it's been turned down. Checking the bios shows no strange temperature shifts.
Hope anyone can help me, because I do not want to go back to my old Asrock mobo

While powered down I cleared the cmos data, removed the Dane Elec DDR2 module and set the bios to optimized defaults. Computer restarted to WinXP with no problems (it has been off the whole night). I shut down WinXP, wait a few moments and then turn the computer back on. Alas, it won't start and starts hick-upping. I turn power off at the PSU again, so it stops.
Now I try switching out the Kingston module instead. By now the computer has been off for 10 min (while I write this entry on laptop). I press the power button on the PSU and then the power button on the front. There is a short pause, lasting a second. The computer turns on, longer now, but it only lasts 2 whole seconds before it turns off again and goes on again (I believe now you can call it powercycling). It repeats this process until I shut off the PSU.
I check to see if I have installed it properly and try again but it starts powercycling again.
15 min pass, I put the Kingston module back in, press the power button and voila, this time it does start. WinXP shows up, no problems. I leave it on for a bit and then shut down. And when I press the power button again - the feeling of dread returns, when it starts hickupping again.
I'm going to see if I can install one of the memory modules from my housemate. Then hopefully tommorrow, I'm going to try if I can test a different PSU, since I see someone else on the forum - who recently posted, has the exact same power supply and also has boot problems, coincidence... or not ^^;.

I have an early 2008 Mac Pro, which has re-booting problems. Also what does the spinning beach-ball indicate?

Hi, I have an early 2008 Mac Pro which has re-booting problems.
Processor speed is: 2.8
Memory: 2GB 800 MHz DDR2 FB-DIMM
2 x 28GHz Quad Core Intel Xeon
I am running OSX Yosemite Version 10.10
My Mac Pro keeps re-booting. Last year I had to replace my graphics card. My original card was the ATI Radeon HD 2600 XT 255MB, and that is what I have now. At this precise moment my Mac Pro is running perfectly, except that it is slow and the spinning beach-ball keeps appearing. I have managed to do some work with the disk utilities, verifying, cleaning and partitioning. Some errors were found and when it was cleaned this seemed to help my Mac Pro to function properly. Although I am able to use my Mac Pro now, from day to day I still experience re-boot problems. Also quite unexpectedly my mac dictionary has an error, it closed itself down and will not open at all, I had the message to say that a report will be sent to Apple.
I have tried starting my computer with an external hard drive fitted via a USB cable, I use for back-ups. This worked and I was able to wipe my hard drive clear and replace all info from the back up I had done only a few days ago.
This worked for a few days and then the same problem started again.
I am beginning to wonder if I need to buy a new hard drive.
If there is anyone who has some answers to help me solve my problem, I would be most grateful.
Robert

When you have the beachball activity, note the exact time: hour, minute, second.
These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
The title of the Console window should be All Messages. If it isn't, select
          SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
          View ▹ Show Log List
from the menu bar at the top of the screen.
Each message in the log begins with the date and time when it was entered. Scroll back to the time you noted above.
Select the messages entered from then until the end of the episode, or until they start to repeat, whichever comes first.
Copy the messages to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
The log contains a vast amount of information, almost all of it useless for solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
Some private information, such as your name, may appear in the log. Anonymize before posting.

Windows 8.1 pro boot problems

I upgraded my OS on a hp pavilion g6-1d73us from windows 7 home premium to windows 8.1 pro and ever since I have had boot problems. I took all the software off since I thought that might be the problem but the boot problems persist. The computer's self diagnosis helps but I still have problems. Is my laptop incompatible with windows 8.1? Windows 8.1 was a download and I still have recovery disks for windows 7. I originally thought the problem was incompatible software but now I am not sure.

Hi @hifive11 ,
Thank you for visiting the HP Support Forums and Welcome. I am glad you have recovery disks for windows 7, smart thinking. I have looked into your issue about your HP Pavilion g6-1d73us Notebook and having issues with the Windows upgrade to 8.1. Here is a link to the drivers page for your product. I do notice there are drivers for Windows 8.The Updates you need for the system are the Chipset. These are located on the driver page link above.
One of the things that can cause an issue is things connected USB. The computer can not load the drivers so it causes an issue. Once the machine is up to date then return the USB devices.
Then I recommended to restore the BIOS to factory defaults.Here is a link to restore the BIOS.
You can do a system restore. System restore will help if something automatically updated and did not go well on the Notebook.
Please note remove any and all USB devices. Disconnect all non-essential devices.
Hope this helps.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

The mother of all re-boot problems.

Hi All,
I've got that re-boot problem that seems very common but the solutions out there aren't working.
Basically the computer will turn on, chime, grey screen comes up, shortly after apple logo, and then the gear starts turning, about 2 minutes later restart, process repeats.
I've tried.
- Booting from CD/Recovery Disk - Won't happen
- A million different key combinations, I've read about 10 different posts on key combinations and tried them all, including PRAM reset, boot from different source, etc.
Basically it's like my keyboard commands aren't being heard at all, but to test if the keyboard was working I pressed the caps lock button and the light was going on and off which tells me its powered. The only kind of input I have been able to acheive is by holding the mouse button down to eject the CD, other than that I have absolutly no control what so ever.
Would like any insight.
Cheers,
Jarrod.

HI,
If you've had your iMac for less then one year then it's covered by the one year limited warranty.
Take it to an Apple store or an Apple certified repair provider.
Carolyn
Message was edited by: Carolyn Samit

Mac Pro Boot Problems. Kona 3?

I'm having booting problems with a Mac Pro. It's got a kona 3 card in one of the PCI slots, and we've been tinkering with it to try to get the audio to work right. However, I've been having huge problems whenever I try to restart the computer. After hitting the power button, or telling it to restart the screen goes to black and sometimes I hear a chime. However, the computer does not boot any further. Then, after holding the power button down and restarting the computer, I can sometimes get the computer to boot normally.
I suspect the Kona card is causing some of the problems. I have multiple hard drives on the system, and I have the ability to boot onto two separate drives in 10.5.8. Both drives are having the same problems.
it's a 2x2.8ghz quad-core Intel Xeon with 10gb of ram. The Kona card is in slot 2. Slot 3 has also been tried, but similar problems remained.

removed kona card. uninstalled aja programs. restart problems still persisting.

Mac Pro Boot Problems After 10.6.2 Update

After installing the latest version of snow leopard I am now having boot problems on my mac pro.
Symptoms;
-Screen resolution is incorrect at apple splash screen.
-Takes a lot longer than usual to boot.
-Once booted the blue tooth magic mouse isn't imediately reckonised, takes a while to find that.
-Once the mouse is finally reckonised it can move around but can't click on anything or bring up the dock. Tried a wired mouse, had the same problem.
-The keyboard is also not appearing to do anything, none of the shortcuts or quick keys work..
Had exactly the same problem after 3 restarts but on the 4th after leaving it for a good 20-30minutes it setled down and everything was working okay. However this is a recurring problem as I had the same thing yesterday...
I have a my 10.5.8 system backed up on an external so I am running from that at the moment. Don't want to go back to snowy til these problems are solved.
Any help will be greatly appreciated!
Martin

Try Safe Mode (It will take more time to startup in Safe Mode because it runs a directory check.)
Let us know.
-mj

Booting Problems

Booting Problems
Help !! my new K8N does not boot from Hard Disk (sorry for very bad english)
My bios detect
Ide Primary MAster : Maxtor 40 Gb -34098H4 5400 rpm Ultra-ATA/100
Ide Primary Slave : ---
Ide Secondary Master : Seagate 120 gb Barracuda - st3120026a 7200 rpm
Ide Secondary Slave : CD-Rom Sony
1st/2nd/3rd Boot Device :Floppy / CD-ROM / Hard Drive
I Format my first partition in NTFS (maxtor) installing XP then not Boot from my hard disk ...only boot from my bootable Xp CD
When i boot up it says
"Verifying DMI Pool Data ..........
DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER"
Finally work!! ...but only work if I turn off Secondary Master & Slave in Bios ==> (NONE)
I change my the IDE HDD cable , jumpers , etc
The memory works good in my old PC (athlon 2.0 hs -MSI k4 ultra)
any suggestion , idea or opinion ? Thanks
CPU AMD Athlon™ 64 Processor 3200+ Newcastle
BIOS Award Phoenix - AwardBIOS v6.00PG
BIOS Award W7030NMS V1.4 082604
MSI K8N Neo Platinum (nVIDIA nForce3-S, AMD Hammer)
Soundblaster Live 5.1
Font Vitsuba Vtx-45-C (450 w)
ATI Radeon 9600 XT 128 mb (RV360) (Asus A9600XT) Internal DAC(400MHz)
Samsung SyncMaster 905DF(X)/955DF(X)/MagicSyncMaster CD195A
Microsoft Windows XP Professional V5.1.2600 (WinXP Retail)
Service Pack 1
DIMM 1
Module Name SMT-OF-AMERICA
Module Size 256 MB (1 rows, 4 banks)
Module Type Unbuffered
Memory Type DDR SDRAM
Memory Speed PC2700 (166 MHz)
Module Width 64 bit
Module Voltage SSTL 2.5
Error Detection Method None
Refresh Rate Reduced (7.8 us), Self-Refresh
Memory Timings
@ 166 MHz 2.5-3-3-7 (CL-RCD-RP-RAS)
@ 133 MHz 2.0-3-3-6 (CL-RCD-RP-RAS)
DIMM 2
Memory Module Properties
Module Name SpecTek
Module Size 256 MB (1 rows, 4 banks)
Module Type Unbuffered
Memory Type DDR SDRAM
Memory Speed PC2700 (166 MHz)
Module Width 64 bit
Module Voltage SSTL 2.5
Error Detection Method None
Refresh Rate Reduced (7.8 us)
Memory Timings
@ 166 MHz 2.5-3-3-7 (CL-RCD-RP-RAS)
@ 100 MHz 2.0-2-2-5 (CL-RCD-RP-RAS)

hi Dzal,
1) Change
1st/2nd/3rd Boot Device :Floppy / CD-ROM / Hard Drive
1st/2nd/3rd Boot Device :Floppy / Hard Drive / CD-ROM
2) Bios
Advanced bios:
Hard Disk Boot Order
1st Maxtor 40 Gb -34098H4 5400 rpm Ultra-ATA/100
2nd Seagate 120 gb Barracuda - st3120026a 7200 rpm
if no [Pageup] [Pagedown] until Maxtor 40 Gb -34098H4 5400 rpm Ultra-ATA/100 top
save & exit
good luck

A very strange boot problem not yet found in the User Forums

Hi
I know you guys are fed up with all the booting problems, but this one is the strangest one I've yet come across.
I'm putting a PC together to function as an extra render for my 3D animations. Here is the specs as follows.
865PE Neo2-P Mobo
Intel Pentium 4 2.8GHz Processor
2 x 256 DDR 400MHz Memory modules (two of the exact same make and model)
300w PSU
60GB HDD Maxdor
nVidia nForce 5600
here is the problem.
It goes past the post, but then the system stops there. It does not go to boot at all.
In the top of the screen below the memory testing and above the HDD and DVD Ram listings it displays as follows:
DEL -> Bios, F12 - Boot Menu etc.
when i press any of keys listed there, that line changes accordingly to the function I selected.
I can get into the BIOS.
But the Motherboard does not boot any further, it just stays there.
I tried diffrent memory, CPU, Powersupply etc, but to no avail.
(I disabled the QUICK BOOT options to see what problems it may give, but it lists none what so ever.)
On the motherboard, where the DIMM2 starts and the MSI CoreCell chip, to above the IDE1 connector to the full length of the IDE connectors, it looks like the transistors/chips connections has a kind of plaque, it does not shine like the rest. Could that be the problem? How can I clean it?
Please help, this is sort of urgent!!!!!!

Disconnect hard & optical drives........
Power up system.
Do you still have freeze on post? (Start up)
I would also concur with Bas, 300w psu no go.
Intel P4 478 2.4 and above Northwood processors are very power hungry. You would be advise to look for PSU with at least 24amps on the +12V rail....... (Enermax 465 and some 365's or the new Corsair VX 450)

KT6V-FISR Boot Problem

Similar Messages

Maybe you are looking for