KT6v integrated network adaptor not been seen by OS

Just got a new board.. a KT6v with the integrated network adaptor. FOr some reason windows XP isnt seeing the Network adaptor. When i plug the network cable into the rj45 jack it lights up. Dont know what to do, XP not even seeing it as an unknow device. Any pointers will be great.

In the Bios settings i  dont see any setting for the nick... maybe after i get windows to install properly i would do a bios update...
and another thing is.. i cant seem to install windows when i have the fsb as 166 mhz to detect my 2600 XP processor... it will only install when i have it set as 133 mhz or 100mhz .. any ideas y ?

Similar Messages

  • Lenovo g570 network adaptor not found (for wifi and blue tooth)

     my lenovo g570 laptop does not found network adaptor for wifi and blue tooth it did not recognize the hardware part may be. because i install software for that so may time. few days back i used wifi as well as bluetooth in my lapi but for last two or three month i just used lan for internet connection and in between i chanded my os wihich is win 7 ultimate to win 7 proff. i dont know what is the reason for that.
    please troubleshoot this so that my lapi can detact network adaptors for wifi and blue thooth.
    vivek
    Solved!
    Go to Solution.

    hi VIVKGP,
    Thanks for Posting!
    Please check under Control Panel and uninstall Lenovo energy Management and uninstall it,
     Now Download and install this, now Download and Install this.
    Lenovo Energy Management -WIndows 7
    caez29ww.exe
    13.6MB
    Restart after Installation
    After Installation:
    Press Fn+F5 and make sure Wifi and bluetooth are on "ON" status.
    You can also Try installing Drivers for both.
    Broadcom Bluetooth Driver
    IN3BTH50WW5.exe
    58.8 MB
    Intel Wireless WiFi Link Driver
    IN1WLN101WW5.exe
    138 MB
    and check the status again.
    Best Regards
    Solid Cruver
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Wireless network adaptor not working

    My wireless network stopped working, and the wireless network adaptor is not showing in the device manger.  The keyboard indicator indicated wifi disabled (f12).  Pushing then button does nothing. It was working fine earlier in the day.  The only change made was an adjustment to text size which required a restart to take affect.  The wireless adaptor did not work on the restart. Not sure what to try next to get it working again. Any advice would be appreciated. Thanks, 

    With two routers you'd have to put one of them into bridge mode. If the linksys is the second router then change its IP from 192.168.1.1 to 192.168.2.1
    You'll still have WPA issues with this configuration because the linksys really is not setup to handle bridge mode very well.

  • Wi-Fi network adaptor not available on my Equium A300D

    Hi
    Hope u can help; I currently have the Toshiba Equium A300D laptop. It got a virus and corrupted 1 of my hard drives, which I now cant use, however I installed the operating system on my other hard drive, everything was fine until I tried 2 connect 2 the internet, windows diagnosed the problem and said it couldnt find the network adaptor for my Wi-Fi.
    Can anybody give me some help in resolving this issue?
    Many thanks

    >...couldnt find the network adaptor for my Wi-Fi
    Is WLAN card recognized and installed properly?
    What is the status in device manager?
    If everything is OK there I presume WLAN card is not enabled properly. At first move WLAN switch to ON position and then use FN+F8 combination to enable WLAN card.

  • PC not seeing the network and not being seen on the network

    I set up a WRT54G to use as my network router. I have two pc's hooked up to it via wire, as the software used for the company requires this. 1 is my server, and there are no problems. I can connect to the Internet fine. The number 2 pc can connect to the Internet fine, but it can not see the network. Number 1 pc can not see the number 2 pc on the network. HELP!!! The work groups are the same, and I followed all the instructions hooking up. My laptop even hooks up to the wireless Internet. What do any of you think? Thanks

    Check firewalls, and any virus suite that you may be using. Make sure that under trusted IPs you have check trust my network. You should be able to find that under personal firewall tabs in the virus suite.
    Stlbluesfan30
    Cisco Network Academy Student

  • AEx not been 'seen' by AX setup utilities

    I've just 'piggybacked' my AEx onto my existing wireless router (BT HomeHub) using the Apple Document: KB 302153, AirPort Express: How to join an existing wireless network in client mode. (Thanx Duane!)
    All went well and set up accordingly, but I now cannot get the 'pulldown' box on iTunes to select speakers; when I run the AEx set assistant or utility, it can see the network, but refuses to see the AEx unit with my speakers. Also, the amber light on the AEx unit is just blinking (which I presume is its way of laughing at me!!)
    all help (in preserving my sanity) greatfully received....

    I have the same problem connecting to the network set up with the new Airport Extreme.
    http://discussions.apple.com/thread.jspa?messageID=4033690#4033690

  • How does this happen: The picture of recent apps you get when double clicking the home button showed in Settings-Wifi that I had been connected to a network I have not been near for two months. Its not a recent "image" of Settings-Wifi. Can anyone explain

    How does this happen: The picture of recent apps you get when double clicking the home button showed in Settings-Wifi that I had been connected to a network I have not been near for two months. Its not a recent "image" of Settings-Wifi. Can anyone explain?

    Greetings,
    I've never seen this issue, and I handle many iPads, of all versions. WiFi issues are generally local to the WiFi router - they are not all of the same quality, range, immunity to interference, etc. You have distance, building construction, and the biggie - interference.
    At home, I use Apple routers, and have no issues with any of my WiFi enabled devices, computers, mobile devices, etc - even the lowly PeeCees. I have locations where I have Juniper Networks, as well as Aruba, and a few Netgears - all of them work as they should.
    The cheaper routers, Linksys, D-Link, Seimens home units, and many other no name devices have caused issues of various kinds, and even connectivity.
    I have no idea what Starbucks uses, but I always have a good connection, and I go there nearly every morning and get some work done, as well as play.
    You could try changing channels, 2.4 to 5 Gigs, changing locations of the router. I have had to do all of these at one time or another over the many years that I have been a Network Engineer.
    Good Luck - Cheers,
    M.

  • The wifi has been lost or disconnected on my iPad. It's the iPad 2 and has not been updated yet. It's IOS 6.1.3 .. how do I add a network back onto it? I have typed in the name and chosen each of the securities and still hasn't connected!

    The wifi has been lost or disconnected on my iPad. It's the iPad 2 and has not been updated yet. It's IOS 6.1.3 .. how do I add a network back onto it? I have typed in the name and chosen each of the securities and still hasn't connected!

    Hey there Luba_kalstad,
    It sounds like you are unable to join your network and cannot see it in the Wi-Fi list in Settings. I would try the troubleshooting outlined in this article named:
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/ts1398
    Be sure you're in range of your Wi-Fi router (access point).
    Tap Settings > Wi-Fi and turn Wi-Fi off and on. If your Wi-Fi setting is dimmed, follow these steps.
    Confirm that your Wi-Fi router and cable or DSL modem are connected to power, turned on, and connected to the Internet. If not, refer to your network administrator or Internet service provider (ISP) for assistance.
    Restart your iOS device.
    Tap Settings > Wi-Fi and locate the Wi-Fi network to which you're connected.
    Tap and Forget this Network.
    Try to connect to your desired Wi-Fi network.
    Note: You may need to enter your Wi-Fi password again if your network requires one.
    Turn your Wi-Fi router off and on2. If your ISP also provides cable or phone service, check with them before attempting this step to avoid interruption of service.
    Update your device to the latest version of software.
    Update your Wi-Fi router to the latest firmware2. For AirPort Base Stations, install updates using the AirPort Utility.
    And this section down toward the bottom if needed:
    Unable to locate a Wi-Fi network
    Verify that the network is available by tapping Settings > Wi-Fi and choosing from the available networks.Note: It may take a few seconds for the Wi-Fi network name to appear.
    Move closer to your wireless router (access point) and attempt to locate the Wi-Fi network.
    If you do not see the network you would like to join, you may be attempting to connect to a hidden network. Learn how to join a hidden network.
    Supported Wi-Fi configurations vary by iOS device model. Find out which standards your device supports3.
    Reset network settings by tapping Settings > General > Reset > Reset Network Settings. Note: This will reset all network settings including:
    previously connected Wi-Fi networks and passwords
    recently used Bluetooth accessories
    VPN and APN settings
    Thank you for using Apple Support Communities.
    Take care,
    Sterling

  • When starting I get an error: "This operation cannot be completed because of an internal failure. A secure network communication has not been cleaned up correctly. "

    Each time I start up Firefox 4.0b6 I am getting the following error message: "This operation cannot be completed because of an internal failure. A secure network communication has not been cleaned up correctly. ". I run Firefox 3.6 as my standard Firefox browser in paralell.

    See https://bugzilla.mozilla.org/show_bug.cgi?id=588511
    (please do not comment in bug reports)

  • FF Beta 4.0b6: The operation can not be completed because of an internal failure. A secure network communication has not been cleaned up correctly. How to FIX ?

    The operation can not be completed because of an internal failure. A secure network communication has not been cleaned up correctly.
    beta 5 and 6 have been useless, unable to connect anywhere once loaded. Fortunately I still have v3x on the machine.

    No answer found.... sorry!

  • The operation can not be completed because of an internal failure. A secure network communicaton has not been cleaned up correctly.

    I closed Firefox after viewing this page (https://www.pcworld.com/news.html) and recieved the following notice:
    The operation can not be completed because of an internal failure. A secure network communicaton has not been cleaned up correctly.
    Is this cause by Firefox?
    Please help!

    That is [https://bugzilla.mozilla.org/show_bug.cgi?id=588511 Bug 588511] (please do not comment in bug reports)
    You should only see that message once after having updated.
    Create a new profile as a test to check if your current profile is causing the problems.
    See [[Basic Troubleshooting#Make_a_new_profile|Basic Troubleshooting: Make a new profile]]
    If that new profile works then you can transfer some files from the old profile to that new profile (be careful not to copy corrupted files)
    See http://kb.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox

  • The operation can not be completed because of an internal failure. A secure network communication has not been cleaned up correctly ... Iget this message when closing firefox. It obviously has been a problem in the past but I'm using FF 6

    '''"The operation can not be completed because of an internal failure. A secure network communication has not been cleaned up correctly ... '''"Iget this message when closing firefox. It obviously has been a problem in the past for others but it has only happened to me since updating to firefox6'''

    Try to clear the "Active Logins" via Clear Recent History
    *https://support.mozilla.com/kb/Clear+Recent+History
    You can also try to delete the file secmode.db in the Firefox Profile Folder
    *http://kb.mozillazine.org/Profile_folder_-_Firefox
    *Help > Troubleshooting Information > Profile Directory: Open Containing Folder

  • The optn cannot be completed because of an internal failure. A secure network communication has not been cleared up correctly.

    Firefox 4.0 b 5 - was doing an update but gave this error message: The operation cannot be completed because of an internal failure. A secure network communication has not been cleared up correctly. - only option = OK

    This is a known bug and it is being worked on.
    The relevant bug report is [https://bugzilla.mozilla.org/show_bug.cgi?id=588511 Bug 588511], but please do not comment on the bug report.

  • An error occurred while reconnecting P: to \\JSERVER\Data Microsoft Windows Network: The network path was not found. This connection has not been restored.

    Almost every day when I open my computer I get this message:
    An error occurred while reconnecting P: to \  \  JSERVER\data Microsoft Windows Network: The network path was not found. This connection has not been restored.
    We then have to go through the process of resetting everything from start to finish just so I can connect to the server. There is no reason that we can find that causes this other than maybe windows updating every night. Any suggestions as to how to
    fix this? 

    it sounds like you have a network drive you are trying to map even though you are not logged in maybe in a script or task instead of backing up to :P backup to the share, make sure you have security set properly to run the task when not logged on.
    I assume you are running a backup of some sort as this is the backup forum..

  • Can't do google seaches or get tabs to open without ringo and get the alert..The operation can not be completed because of an internal failure. A secure network communication has not been cleaned up correctly.

    I can't get tabs to open or google search to operate without constant ringo and I get the alert...The operation can not be completed because of an internal failure. A secure network communication has not been cleaned up correctly. I have 8.0 firefox version

    This is a known bug and it is being worked on.
    The relevant bug report is [https://bugzilla.mozilla.org/show_bug.cgi?id=588511 Bug 588511], but please do not comment on the bug report.

Maybe you are looking for

  • How do I deal with the warning message: Stale; Enable pool

    Hello, I have a small (4TB) storage space on an installation of Server 2012 Essentials and it's thrown up this warning message on one of the physical drives (see screenshot). There doesn't seem to be very much additional information, or actions avail

  • Update shipment partner address E1ADRM4 & BADI_LE_SHIPMENT

    Hi, We want to update an existing shipment with updated detailed address information from an incoming Idoc from the forwarding agent. The idea is to replace the generic phone, email, name etc. with the specific clerk handling this shipment. We are on

  • MDS switch: DCNM: Is there a way to monitor the traffic on every port within a port channel using DCNM?

    I am trying to monitor the load on an 8 port ISL between 2 MDS FC switches, on DCNM.  Since it is a plain trunk link, I am able to monitor the stats of every ISL port individually.  My question is, since port channel shows up as a single interface on

  • New event with no sound from iPhone

    When I set a new event with an alert from iPhone, on iCal of my iMac (synched via Mobile Me) I always got as alert a "message with no sound". How can I get an alert with sound (on my iMac) when I set a new event from the iPhone?

  • Deploy project from Workshop onto production server

    Hi all, How do I deploy a project I made in the workshop to a remote production server? I 've tried several ways: - With application settings in workshop: hangs (even when I copied the domain from the server and used that) - From weblogic builder: ha