KT8 Neo.......Led Activity does not work with SATA drives

Is this another MSI Flop.
Does anybody know if the HD led works when using SATA drives connected to the Via controller on the K8T Neo board?
I checked the case led and it works fine. It is not burnt out.
I also have the K7N2 Delta board and the HD led does not work on that board either when using SATA hard drives. I was told the led connecter was never wired to detect activity for the SATA drives only for IDE. A bios upgrade would never fix it.
I just setup K8T Neo and other than the HD Led not working the board seems to be pretty stable.

The only led activity I get is when the board is first powered on and I just recently noticed when I play a DVD. The led seems to flicker when the dvd is playing.
Other than that I see no led activity with 1 or 2 SATA drives connected to the VIA controller.
Can someone confirm that it either works or it doesn't work.
I keep reading all these posts and some say it works and some say it don't.
Unless their is a new revision of the KT8 Neo and everybody is connecting their led to the HDD Led pins on JFP1 (Page 2-19 in the manual) they all should either work or they all should not workl. From what I gather their is no new revision of the board and only one Bios v1.1.
It also seems their was some confusion on what connector people were connecting thier led to on the motherboard. From what I read on page 2-19 in the manual thier is only one choice on JFP1 (Top row, pins 1 & 3).

Similar Messages

HD Led not working with SATA drives on MSI K7N2 Delta

I noticed the HD led does not work with the SATA drives on my MSI K7N2 Delta ISLR
I confirmed that the led is not burnt out by reconnecting a spare IDE HD with XP on it to IDE 1 and the led worked when there was activity, but it does not work when connected to IDE3 or if the SATA drives are connected to Serial 1 & 2.
Could it be because the motherboard doesn't support and hdd led for the Promise SATA controller.
I had Bios v7.3 and flashed to v7.4 with no luck.
Could a new bios update fix this problem?
Anybody seen this before?

basically it not wired up so works for no one

Flash player does not work with Ie or Firefox with win 8.1?

Flash player does not work with Ie or Firefox with win 8.1 64, If i try and play a video I get the message to install Flashplayer.
If I try and install it it says it is already installed. Your onsite installer says it is not applicable to my machine.
I have followed all the normal steps re enabling addons and active filters etc.
all to no avail Pc is Dell 6 months old, Flashplayer has never worked on this machine. Last MS update mid Dec 2014.
Version of flashplayer is 15....03.......

Flash Player is a built-in component of Internet Explorer. There's nothing separate to download or install.
Firefox requires a different version of Flash Player (the NPAPI plug-in), which will be served to you if you go here: http://get.adobe.com/flashplayer using Firefox; however, there are some unique stability issues related to Firefox on Win8.1, and you're probably better off using Google Chrome if you want a more optimal experience with Flash Player.
For problems where IE isn't being detected by sites that require Flash:
First, confirm that ActiveX Filtering is configured to allow Flash content:
https://forums.adobe.com/thread/867968
Internet Explorer 11 introduces a number of changes both to how the browser identifies itself to remote web servers, and to how it processes JavaScript intended to target behaviors specific to Internet Explorer. Unfortunately, this means that content on some sites will be broken until the content provider changes their site to conform to the new development approach required by modern versions of IE.
You can try to work around these issues by using Compatibility View:
http://windows.microsoft.com/en-us/internet-explorer/use-compatibility-view#ie=ie-11

I bought an unlocked iphone 4s from dubai but it does not work with an indian idea sim..help

i bought an unlocked iphone 4s from dubai but it does not work with an indian idea sim..help

If you are both on the T-mobile network, the sim card should work. If you did a Erase All Content and Settings, then she should be at the point of activation as a new device...talk to T-mobile and be sure the sim she is using is a valid sim card.

Brightness control does not work with the bluetooth keyboard connected on my iPad2. Please someone could help me ?

Brightness control does not work with the bluetooth keyboard connected on my iPad2. Please someone could help me ?

Julien-
I have the Apple MC184LL/A Bluetooth Wireless Keyboard. The brigtness control works with mine, as do most of the other functions.
Try cycling the keyboard off and on. Hold the power button until the green LED goes out. Then press it one more time to turn it back on.
You might try resetting the iPad's network. Go to Settings-General-Reset-Reset Network Settings. Then you may need to reconnect your WiFi and Bluetooth.
If that doesn't help, try resetting/rebooting the iPad. Hold both the Home and Sleep buttons for several seconds until the Apple logo appears. Ignore the "Slide to power off" arrow. The iPad will restart in a couple of minutes. Resetting this way will not hurt anything, and sometimes clears up mysterious problems.
Fred

I have recently upgraded my iMac Intel G5 iSight to OS 10.6.8 and now the internal mic does not work with skype or facebook. I can here static when playing back clips. Do I need to update firmware or reload old sys parts

I have recently upgraded my iMac Intel G5 iSight (iMac5,1) to OS 10.6.8 and now the internal mic does not work with skype or facebook. I can here static when playing back clips. Do I need to update firmware or reload old system parts. I have zapped PRAM. The blue indicator in system audio panel will appear for a second as I slide the bar for internal mic but then it disappears. Is there a fix?

The sound seems very faint but can here static on playback.

Flash player does not work with new ICS Android 4.0.4 OS. Has this problem been addressed?

Flash player does not work with new ICS Android 4.0.4 OS. Has this problem been addressed? I am using Firefox Beta for android and I also tried just Firefox.

Please check the Play Store app for any Flash updates and install them if present.

My Time Capsule does not work with existing WiFi

Following a question solved on March 24 by LaPastenague, but gone bad again.
Apple AirPort Time Capsule
I felt the need for a physical backup of my data, as I would not completely trust the different clouds. I use, and have used Dropbox for 4-5 years and are very satisfied with that, but I am still not sure if or when a political lunatic will shut off the internet.
I purchased the Apple AP Time Capsule 2T, because all my other stuff are Apple, and that it's wireless. My old backup is Maxtor 300 GB.
Since we stay 2-3 weeks on two locations, one in Norway and one in Sweden (two different countries) we must use Mobile Broadband 4G, cables or fibre connections are useless for us, and we don't have it up to the houses. I have one mini router for each country, we bring with us iPhones, iPads, iMac, Apple TV, APExpress. When we pass the boarder I change the mini router, and the system continues working perfect on the WiFi, except the APExpress that needs to be reconfigured, but then it works.
The APTC was difficult to make working as it would not accept to be in an existing network, but with good help from the Apple Community, LaPastenague, with forcing the TC connect to the APE with Ethernet cable in bridge mode, ref "My Time Capsule does not work with existing WiFi" from March 24, the problem was solved and all gadgets worked together in a perfect harmony, until we changed location.
Now, as I have my second WiFi network, and the APExspress is reconfigured, it's like the TC thinks, I am the base boss here, I am not taking orders from APE one more time, and it simply does not work, not only that, it fluctuates all the time.
I have a slight feeling that the two WiFi bands are making the trouble as during the configuration of the TC sometime the last figure 6 and 7 pops up, and that has something two do with the two different 2,4 and 5 GHZ bands
So, I am curious if you have any idea ?
I am thinking of returning the TC if I don't make it work now, but how do I delete all the data that's on it?

I can deal with the last question first and easily.
I am thinking of returning the TC if I don't make it work now, but how do I delete all the data that's on it?
Open the airport utility .. go to the disk tab and select erase.
When you select erase you will get mulitiple options.
Quick removes the file table but does not delete the files,, it takes 2min or less.
A Zero out data is the secure way,, by writing 0 ie low level drive format.
It can take several hours..
7 pass will take a week.. not recommended..
35 pass erase is ridiculous.. it would take a month.. put an ax through the TC. It is quick and better.
Now, as I have my second WiFi network, and the APExspress is reconfigured, it's like the TC thinks, I am the base boss here, I am not taking orders from APE one more time, and it simply does not work, not only that, it fluctuates all the time.
The fact that it did work and has now failed might point to faulty unit.
The only way to tell is reset it properly to factory and start over.
Universal Factory Reset.. any model TC or AE.
Unplug your TC/AE from power or turn off at the power point.
Hold in reset. and power the TC/AE back on.. all without releasing reset and keep holding in for about 10sec. (this is often difficult without a 2nd person or a 3rd arm).
Release it when the status light flashes rapidly. If it doesn’t flash rapidly you have missed it and try again.
Note..
Be Gentle! Feel the switch click on. It has a positive feel.. add no more pressure after that.
TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations of the router.
No files are deleted on the hard disk in a TC.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
Generally having multiple wireless AP should not cause problems.. but it is better to set channels manually.. so it doesn't go beserk rotating channels.
Remember to keep all names short, no spaces and pure alphanumeric.
Sadly though the Apple routers have no logging now and no SNMP and almost nothing to help diagnose a problem, so if it continues .. take it back to apple.. they have given you no other method of fixing it.

ITunes 12.1.1 does NOT work with Windows - Fix??

Hi everyone,
I had issue after issue with the latest iTunes update (12.1.1) not working on my windows 7. It simply would not lunch when clicking on the shortcut to open.
After a fair bit of searching I found this alternative version which seemed to do the trick and now it works:
iTunes 12.1.1.4 for Windows (64-bit - for older video cards) - iTunes64Setup.exe(2015-02-18)

The "for older video cards" installer - which, like most prior "64 bit" versions of iTunes, is actually a 32 bit application with a 64 bit installer - may be a useful fallback if the full 64 bit version does not install or run correctly. Although 12.1.1.4 is a major improvement over 12.1.0.71, there are clearly still some lurking incompatibilities with some 64 bit Windows systems/components. It is, however, a little misleading to say that "iTunes 12.1.1 does NOT work with Windows" - in many cases it works fine without switching to the alternative version. I have the full 64-bit version of 12.1.1.4 running on three systems - two Windows 7 and one Windows 8.1 - no issues with either installation or operation on any of them.

Home sharing does not work with new mountain lion update.

home sharing does not work with new mountain lion update. Does anyone else have the same issue. Updated all computers in my home, deauthorized and reauthorized each computer. turn off home sharing and turned it back on. don't know what else to do..please help...

Our Apple TVs continue to lose connection ever since installing Mountain Lion on the host computer. The only thing that fixes them is to quit and relaunch iTunes, which only works unti the ATV goes to sleep. If a movie is paused for more than a few minutes and the ATV goes to sleep, pressing play again on the remote is greeted with "There are no movies on this computer" or "Turn on Home Sharing."
If we stop a video on one ATV and attempt to resume it in another room, the error begins again. The other ATV can't connect until iTunes is relaunched.
My guess is that it has something to do with the new [annoying] security settings. But I still haven't found a fix other than restarting iTunes everytime we want to watch something from our downloads. Fail.

External USB HD does not work with HAL:

External USB HD does not work with HAL:
From the last 10 days the HAL auto-mount with ntfs-3g file system of my external hard drive does not woks.
But the manual mount procedure with the command mount -t ntfs-3g /dev/sdb* /mnt/XYZ works.
I've followed the instructions in the wiki: http://wiki.archlinux.org/index.php/HAL and the system has worked up to the last kernel or HAL update.
My fat32 usb-stick works without any problem.
If I try to open the device with KDE it appears an error popup wit this message:
TODO: have to rethink extra options
Error: kio_media_mount_helper
The log from the kernel.log is
Nov 6 22:03:16 myhost usb 5-1: new high speed USB device using ehci_hcd and address 4
Nov 6 22:03:16 myhost usb 5-1: configuration #1 chosen from 1 choice
Nov 6 22:03:17 myhost Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Nov 6 22:03:17 myhost ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Nov 6 22:03:17 myhost Initializing USB Mass Storage driver...
Nov 6 22:03:17 myhost scsi6 : SCSI emulation for USB Mass Storage devices
Nov 6 22:03:17 myhost usb-storage: device found at 4
Nov 6 22:03:17 myhost usb-storage: waiting for device to settle before scanning
Nov 6 22:03:17 myhost usbcore: registered new interface driver usb-storage
Nov 6 22:03:17 myhost USB Mass Storage support registered.
Nov 6 22:03:22 myhost scsi 6:0:0:0: Direct-Access WDC WD32 00JB-00KFA0 0811 PQ: 0 ANSI: 0
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sdb: sdb1
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Attached SCSI disk
Nov 6 22:03:22 myhost sd 6:0:0:0: Attached scsi generic sg2 type 0
Nov 6 22:03:22 myhost usb-storage: device scan complete
and the error.log is
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Do you have some idea ....
Bye.

I have done the following:
Downloaded the patched hal version.
used makepkg in /abs/local/trunk/ to create a pkg for pacman
used sudo pacman -U pkgname to install it.
used sudo nano /etc/hal/fdi/policy/preferences.fdi to create the fdi file with the following content:
saved the file and removed my ntfs entryes from fstab and rebooted. and still there is no automount off ntfs partitions.
have i done something wrong?
br fjodork
WARNING: what follows is a guide of what did work for me, I'm still in an early stage of learning linux, so please correct me if anything of what follows is wrong/dangerous/stupid. As I said, this worked for me, it's not pretty, since I was learning each step on the fly and I'm sure there are better ways to do this.
So fjodork, you seem to have done the the necessary steps, though i couldn't get it to work until i first removed hal without dependencies
pacman -Rd hal
it will give you some warning about the dependencies, ignore it since we are reinstalling hal in a few steps.
First i tried to follow Raymano's link, obviously it showed me nothing in the browser so I thought it might be a broken link.
So I downloaded the source tarball from here http://hal.freedesktop.org/releases/hal-0.5.10.tar.gz
unpacked it changed the /tools/hal-storage-mount.c as per Milfadoodle's instructions.
at first I tried to compile directly from source, the process would finish without a glitch though after reboot nothing changed, as if hal weren't
installed, i guess there were issues with paths. anyway read on
Then repacked the source in tarball, copied it to /var/abs/extra/system/hal and modified the PKGBUILD as follows
makedepends=('pkgconfig' 'gperf')
options=('!libtool')
install=hal.install
source=(${pkgname}-${pkgver}.tar.gz #removed url so makepkg looks in the current directory for the tarball
hal
hal-policy.patch
cryptsetup_location.patch
hal-0.5.9-hide-diagnostic.patch
ntfs3g-valid-options.patch)
md5sums=('6641c30a27c00485c6accac5110ff911' # replace with md5sum of your package's sourceball (run md5sum filename)
'882f67668cb14a0a9e4a27ef22278027'
'5ba8b610aa9763a5f42b9f7cbd7a86ad'
then makepkg (i had to add --asroot, don't ask why
and finally pacman -U hal-0.5.10-1-i686.pkg
another reboot and everything worked without a glitch!:D (yeah i know i still haven't got rid of the reboot mentality )
I have also put the policy files as per the wiki instructions.
PS: I know this is a dirty way to getting things done but as i said, I'm just starting
If anyone could comment/correct/explain this post I'd be more than happy, the automount issue was bothering me for about a month now (you'll say why do I need ntfs in the first place? well, I only recently switched for Linux as my primary OS, these are some relics of the M$ era

APPLE TV DOES NOT WORK WITH NETFLIX

APPLE TV DOES NOT WORK WITH NETFLIX, just a black screen and "Netflix is loading" message appears. I can´t even see Netflix´s home page or set up my account. Netflix is working fine on all other devices at home, but in Apple TV.
I have tried the 8.8.8.8 DNS trick, the turn off procedure, the manual IP setting, but nothing....black screen still appears

It started working.....!!!!! (It seems someone back there is listening)
I "forced" an upgrade, I mean it showed "AppleTV is updated", nevertheless I re-started the system using the "return to original configurations" option. Then it updated again by itself to a newer version....and started working perfectly.
I have paired my apple wireless keyboard and it works fine, this way is easier to set up passwords or so (you can also do it with your remote).
TIPS:
I didn´t change any language or video quality configuration (scared to do so)
I changed to ethernet (cable) instead of wireless
My internet plan is 6 Megabytes (it was the same while it wasn't working)
good luck!!

I bought this iPhone from Apple Retail Store for the full amount, but it does not work with my SIM card only works with AT&T

Hello,
I have an iPhone 4S 32Gb White AT&T, product part No. MC921LL/A, Serial No. C39GMLPWDTDC
I bought this iPhone from Apple Retail Store (from Fifth Avenue, NY) for the full amount. Now it does not work with my SIM card only works with AT&T. I restored the phone several times, but I have not received "Congratulations your iPhone has been unlocked". Please activate my iPhone to work with different SIM cards
Thanks,
Best Wishes

When did you buy it?
Apple did not begin selling an unlocked version of the iPhone 4S in the US until 11/11/11. I believe it went on sale only through the online store at that time. I'm not sure if it's available at retail yet.
What you purchased was a phone without a contract commitment. It is still locked to AT&T. AT&T will NOT unlock iPhones for any reason. Return it and get your money back, then use that to purchase an unlocked phone.

Ipod does not work with new usb

i got my computer cleaned and a usb 2.0 pci card put in and now my ipod does not work with it, can anyone help

tell me what you mean and i will tell. i ask the guy in the shop to remove any viruses and put my files in order and also put winzip on, ad-ware se peronal and windows defender. and to install a usb2.0 pci card, so that i can put music onto my ipod faster. is this enough for you

Macbook Pro 2011 DVI HDMI out does not work with TV when the power cable is connected

My Macbook Pro (Early 2011) DVI HDMI out does not work with TV when the power cable is connected. If get the blue screen and then can use the macbook but nothing is displayed on the TV. If i go into display I can see that there are two screens but nothing displayed on the TV. If i take the power cable out at this point the TV shows the second desktop as expected. If i then reconnect the cable, the screen flickers, as though it is being affected by the power cable, and the screen goes blank on the TV. Only if i remove the DVI cable do i get the blue screen again. If i remove the power cable and reconnect it will do it every single time, so i cannot see it being a TV issue or a minor glitch.
I have had this working previously but at the minute it seems to not be playing ball....any thoughts
Thanks
Dan

BUMP
Any ideas?

KT8 Neo.......Led Activity does not work with SATA drives

Similar Messages

Maybe you are looking for