L2-MPLS-IOS Support

Hi all,
need help. we r ISP and we need to implement L2-MPLS, we hv 7513 in our network as a PE and need to know which IOS will support L2-MPLS,QoS,MPLS OSPF,MPLS RIP.
Thanks & Regards,
Ciscobuddy

The following images for 7500 which is of 12.0(26)S release might help you in implementing your requirement "rsp-pv-mz.12.0-26.S1" or "rsp-pv-mz.12.0-26.S". This image requires 128MB of DRAM and 16MB of flash .

Similar Messages

MPLS VPN support for VPNv6

All,
which routers and IOS has MPLS VPN support for VPNv6?
regards
Devang Patel

Hello Devang,
in the feature navigator look for the 6VPE feature for example a C7609 with sup720 3BXL and IOS 12.2(33)SxHa2 has the vpnv6 address-family.
see for example
http://www.cisco.com/en/US/docs/ios/ipv6/configuration/guide/ip6-ov_mpls_6vpe.html
you still need an MPLS/Ipv4 core or an ipv4 core if using GRE tunnels:
Table 1 Feature Information for Implementing IPv6 VPN over MPLS
Feature Name Releases Feature Information
IPv6 VPN over MPLS (6VPE)
12.2(28)SB
12.2(33)SRB
12.4(20)T
The IPv6 VPN (6VPE) over a MPLS IPv4 core infrastructure feature allows ISPs to offer IPv6 VPN services to their customers.
This entire document provides information about this feature.
MPLS VPN 6VPE support over IP tunnels
12.2(33)
SRB1
This feature allows the use of IPv4 GRE tunnels to provide IPv6 VPN over MPLS functionality to reach the BGP next hop.
This following sections provide information about this feature:
â¢6VPE Over GRE Tunnels
Hope to help
Giuseppe

Does adobe reader for android/ios support digital signature?

does adobe reader for android/ios support digital signature?

when to support digital signature in adobe reader for android/ios?

IOS support for Flash Builder 4.5.1

I am getting the following message when I try to export a releae build to iOS using Flash Builder 4.5.1:
This platform is not currently supported for Flex Mobile projects
I have tried running the update again and gives me the update was successful message, but I still don't have iOS support.
I did update using the Eclipse updater and was unable to open Flash Builder, but since resolved that issue. I wonder if I need to reinstall Flash Builder and reapply the update or if there is an easier fix.

I just created a project with Adobe Launchpad (http://labs.adobe.com/technologies/airlaunchpad/), and it looked like I setup all the options for iOS, but when I go to run configurations and try and deploy to an iOS device I'm getting the same problem: "This platform is not currently supported for Flex Mobile projects"
Anyone know why?

The version of iOS on does not match any of the versions of iOS supported for development with this installation of the iOS SDK

Getting this error message as of this morning: The version of iOS on “iPad” does not match any of the versions of iOS supported for development with this installation of the iOS SDK. Please restore the device to a version of the OS listed below, or update to the latest version of the iOS SDK. I've downloaded the latest SDK and gone through the usual turn off and turn on again for iPad and computer, removed and reinstalled the iPad from Organizer and have no idea how to make apps build now. I was prompted to update the iphone too but there's no way I'm updating it if this issue can't be resolved.

Okay these are the steps I took to solve the problem - they may not be the right ones for you but they've solved the problem and saved time hunting for some other solution. Firstly I changed my MAC system to Lion with the £20 download, then I deleted the old Xcode and installed the new version that is app based and doesn't support Snow Leopard, then all was well. I can now update my xcode via the app which is quicker and more logical and can update my iPhone rather than chug along avoiding updates as I need to update my existing apps on the app store and upload a new one.

Does Adobe AIR for iOS support APNs?

Does Adobe AIR for iOS support the Apple Push Notification Service (APNs)?
for more information on APNs see:
http://developer.apple.com/library/ios/#documentation/NetworkingInternet/Conceptual/Remote NotificationsPG/ApplePushService/ApplePushService.html

It is exactly the same.
Do I need to add the mobileprovision in any step of the resigning process?
Inside the unpacjed ipa, i've fund a Info.plist.
This seems to be the plist file generated from adt.
Do I need to integrate my entitlement with the original one?
<?xml version="1.0" encoding="UTF-8" standalone="no"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
<plist version="1.0">
    <dict>
        <key>CFBundleAllowMixedLocalizations</key>
        <true/>
        <key>CFBundleVersion</key>
        <string>0.0.0</string>
        <key>CFBundleShortVersionString</key>
        <string>0.0.0</string>
        <key>CFBundleIdentifier</key>
        <string>XXXXXXXX</string>
        <key>CFBundleInfoDictionaryVersion</key>
        <string>6.0</string>
        <key>CFBundleExecutable</key>
        <string>iBatteryExample</string>
        <key>CFBundleDisplayName</key>
        <string>iBatteryExample</string>
        <key>CFBundlePackageType</key>
        <string>APPL</string>
        <key>DTCompiler</key>
        <string>4.2</string>
        <key>DTPlatformBuild</key>
        <string>8C134</string>
        <key>DTPlatformName</key>
        <string>iphoneos</string>
        <key>DTPlatformVersion</key>
        <string>4.2 Seed 2</string>
        <key>DTSDKName</key>
        <string>iphoneos4.2</string>
        <key>DTXcode</key>
        <string>0325</string>
        <key>DTXcodeBuild</key>
        <string>10M2423</string>
        <key>LSRequiresIPhoneOS</key>
        <true/>
        <key>MinimumOSVersion</key>
        <string>4.0</string>
        <key>NSMainNibFile</key>
        <string>MainWindow</string>
        <key>NSMainNibFile~ipad</key>
        <string>MainWindow-iPad</string>
        <key>CFBundleResourceSpecification</key>
        <string>ResourceRules.plist</string>
        <key>UIStatusBarHidden</key>
        <false/>
        <key>renderMode</key>
        <string>auto</string>
        <key>CTRequestedDisplayResolution</key>
        <string>high</string>
        <key>DebugMode</key>
        <false/>
        <key>CTSoftKeyboardBehavior</key>
        <string>none</string>
        <key>CTNamespaceURI</key>
        <string>http://ns.adobe.com/air/application/3.0</string>
        <key>CTAutoOrients</key>
        <true/>
        <key>CTInitialWindowTitle</key>
        <string>iBatteryExample</string>
        <key>CTInitialWindowContent</key>
        <string>xxxxx.app/xxxxxxxx.swf</string>
        <key>CTMaxSWFMajorVersion</key>
        <string>13</string>
        <key>CFBundleSupportedPlatforms</key>
        <array>
            <string>iPhoneOS</string>
        </array>
        <key>UIDeviceFamily</key>
        <array>
            <string>1</string>
            <string>2</string>
        </array>
        <key>aps-environment</key>
        <string>development</string>
        <key>com.apple.developer.aps-environment</key>
        <string>development</string>
        <key>get-task-allow</key>
        <true/>
        <key>UIRequiredDeviceCapabilities</key>
        <array>
            <string>armv7</string>
            <string>opengles-2</string>
        </array>
        <key>UISupportedInterfaceOrientations</key>
        <array>
            <string>UIInterfaceOrientationPortrait</string>
            <string>UIInterfaceOrientationPortraitUpsideDown</string>
            <string>UIInterfaceOrientationLandscapeRight</string>
            <string>UIInterfaceOrientationLandscapeLeft</string>
        </array>
        <key>Extensions</key>
        <array>
            <string>myExtension</string>
        </array>
    </dict>
</plist>
as you can see it already contains the aps-environment value because I've added it in my appdescriptor file.
Any idea?
Thanks

AIR for Apple iOS Support in Flash Builder is not installed.

I've written an application in Flash Builder and I'm now attempting to get it running on an iPad.
I am running on a Mac (OSX 10.6.7)
I have FB 4.5 installed and downloaded the separate 4.5.1 update file successfully updated FB to 4.5.1.
I have downloaded and installed AIR 2.7.
I have downloaded and installed the AIR sdk.
I have an iOS developer account and have created my developer certificatn p12 file, created an Apple Id for my application and a provisioning profile.
I created a new "ActionScript Mobile Project" for my application and enabled the Apple iOS platform.
I have entered my certificate and provisioning information into FB.
I created a "Debug Configuration" for my project.
When I run my debug configuration, I am prompted for my Certificate Password (which I enter).
I then receive a pop-up message with the following error:
"AIR for Apple iOS Support in Flash Builder is not installed. To enable packaging support for Apple iOS follow these instructions."
The link for the instructions links to the following knowledge base article:
http://kb2.adobe.com/cps/899/cpsid_89938.html
I have Flash Builder as a part of the CS5.5 Web Premium (on DVD), which does not appear to have a "AIR for Apple iOS Support" option during the FB installation.
So I followed the manual installation steps provided (although copying the described folders to my sdks/4.5.1 folder (rather than the sdks/4.5 folder).
However, doing the above did not resolve the issue. I still get the same error message as before.
Has anyone else encountered this issue, or have any suggestions on how to resolve it?
Thanks in advance.

In case anyone else runs into this issue:
This problem was solved in this other thread in the Adobe AIR Installation Issues forums:
http://forums.adobe.com/thread/867868?tstart=0
Craig.

My customized external device(having SPP BT profile) doesnt support iOS support bluetooth profiles, so i need to join MFi program.Does MFi program hepls to support SPP profile or i need to change my devices BT profile.Ask your question.

MFi program will continue to support SPP profile or i need to rewrit, to make my device support "iOS support bluetooth profiles"

I expected this to be released quite earlier. But now that it's in process, I'll wait patiently.
Make it easier for other people to find solutions, by marking my answer with \'Accept as Solution\' if it solves your problem.
Click on the BLUE KUDOS button on the left to say "Thanks"
I am an ex-HP Employee.

Does reader for iOS support text reflow?

I have a number of tagged PDFs that I created using Acrobat on a Windows machine, and transferred them to my iPhone. Does Reader on iOS support text reflow so that I can increase the font and read my document? The only option I see is to zoom in, but since it maintains the full page formatting, I then need to "move around" the page to actually read the text. Looking at the full page, the text is too small.
Thanks.

Hi Dennis, how are you going to find out if there is enough demand? Do you think everybody knows what text reflow means? And do you think every person that needs it will create an account (just like I had to do) to comment in this community requesting the feature? Text reflows is such a useful feature that it should be available by default in all smartphone platforms iOS, Windows and Android. I know it is available in Android and that's why I downloaded the app in my iPhone but I was quite disappointed to find out that it is not available on the iPhone. I'm sure that if in the next update of the iOS adobe app text reflow is included (and if you let the public know about it) then a lot more people will download the app. Reading pdf in an screen is not so pleasant but text reflow makes it really easy.

Update Failed: AIR for Apple iOS support

While Updating my Flash Builder 4.5 to 4.5.1, and 2 other updates, one being the AIR for Apple iOS support.
When I try installing the update for the iOS support, I get the message: Update is not applicable. Error Code: U44M1P28

Trying to figure out another solution, I uninstalled Flash Builder 4.5 Premium, to install a new full version of 4.5.1 from Adobe's website.
While Installing, I get the following message which showed me exactly where my problem is... I have a prereleased version of AIR for Apple iOS Support.
The Question is... How do I uninstall the prerelease version of AIR for Apple iOS Support? I uninstalled FB4.5, and I removed the remaining folder after installation that was in Flash Builder 4.5 that was in Utilities. though, I still get the message above...
Any idea on how to Uninstall a Prerelease version of AIR for Apple iOS Support?! No where to be found online.

MPLS CE support on Cisco 2800 ISR router

Hi all, could I ask you for some hints about MPLS CE support on Cisco 2800 ISR router today? I`m finding restrictions and recommendations for feature implementation. Do you have any cisco web site about them?
Thank you for your advice and/or hints.
Peter

Thanks for an answer. I need to use multi-VPN model on CE router, but with QoS on one physical CE-PE connection (e.g. Frame-Relay DLCI).However, all VPNs on CE router must be secured for each one. The solution is Multi-VRF service feature, but, however, with multi-DLCI model on Frame-Relay and QoS per DLCI. Now, I`m finding a scenario to provide multi-VPN model on CE router with single-DLCI model and single QoS per one DLCI for all VPNs. And that, MPLS CE feature on C2800 could be used, if possible.
So, I don`t know more about MPLS CE on C2800 and I don`t know make a result to propsed solution...

I want the iphone 4 ios supports 8 be kind are not bad not let oblivion because the iphone 4 is as good as the iphone 4s

I want the iphone 4 ios supports 8 be kind are not bad not let oblivion because the iphone 4 is as good as the iphone 4s

iOS 8 requires a dual-core processor; the iPhone 4S has that, but the iPhone 4 doesn't.
(117890)

Ios supports jpeg2000 images.

I wanna use jpeg2000 image in my ios apllication.
Does ios supports jpeg2000 and if Mac OSX supports jpeg2000 images then how can we port this in ios?

According to a review of iPhoto for iOS published on the MacWorld website iPhoto for iOS downsizes images when they are imported from your computer. Actually I believe that it's the iPad itself that does this. In any case you end up with a max of about a 3 mp image. That's great for social sharing sites but not to much for real editing of photos that you might want to print.
iPhoto for iOS will edit photos up to 19 mp but they have to be imported via the camera connection kit directly from an SD card or the camera. So iPhoto should edit large jpg files imported directly. But the article does say that iPhoto for iOS does not edit RAW files.
You can see the article here
http://www.macworld.com/appguide/app.html?id=1189243&expand=true

What RFC for MPLS is supported?

Hi,
does anybody know what rfc's regarding mpls are supported by cisco (f.e. ASR9000 or Nexus 7000)?
TiA,
Stephan

Hi Stephan,
this is the list for ASR9k:
RFC 2547, BGP/MPLS VPNs
RFC 2702, Requirements for Traffic Engineering Over MPLS
RFC 2858, Multiprotocol Extensions for BGP-4
RFC 3031, Multiprotocol Label Switching Architecture
RFC 3032, MPLS Label Stack Encoding
RFC 3063, MPLS Loop Prevention Mechanism
RFC 3140, Per Hop Behavior Identification Codes
RFC 3270, Multi-Protocol Label Switching (MPLS) Support of Differentiated Services (E-LSPs only)
RFC 3443, Time To Live (TTL) Processing in Multi-Protocol Label Switching (MPLS) Networks
RFC 3469, Framework for Multi-Protocol Label Switching (MPLS)-based Recovery
RFC 3564, Requirements for Support of Differentiated Services-aware MPLS Traffic Engineering
RFC 4124, Protocol Extensions for Support of Diffserv-aware MPLS Traffic Engineering
RFC 4125, Maximum Allocation Bandwidth Constraints Model for Diffserv-aware MPLS Traffic Engineering
RFC 4127, Russian Dolls Bandwidth Constraints Model for Diffserv-aware MPLS Traffic Engineering
RFC 4379, Detecting Multi-Protocol Label Switched (MPLS) Data Plane Failures.
RFC 3815, Definitions of Managed Objects for the Multiprotocol Label Switching (MPLS), Label Distribution Protocol (LDP)
RFC 4448, Encapsulation Methods for Transport of Ethernet over MPLS Networks
RFC 5462, Multiprotocol Label Switching (MPLS) Label Stack Entry: "EXP" Field Renamed to "Traffic Class" Field.
HTH,
Ivan.

Does iOS support syncing contact photos using Bluetooth PBAP?

I know iOS supports PBAP.
I know the PBAP protocol supports syncing pictures (http://www.spinics.net/lists/linux-bluetooth/msg28488.html)
Does iOS supports this too?

No one would have any idea what Apple plans, unless they announse - which is very rare.
Iphone does not support bluetooth printing.

L2-MPLS-IOS Support

Similar Messages

Maybe you are looking for