L2 Roaming issue with Avaya wireless phone on WISM -V6.0.196.0

Hello Friends,
I am facing Layer2 roaming issue with Avaya Wirless phone 3620 which are configured WPA / Pre-shared key auth with a SSID1 and face a cut or delay in the voice.
But when i use Cisco Wireless phones and try to roam between one LWAP to other i dont face a cut or delay in the vocie which are
Configured with 802.1x +CCKM auth .
Then i configured new SSID 3 with 802.1x+CCKM settings for the new Avaya wireless module 3631 , but still face cut and delay while doing Layer 2 roaming.
While i was using these AP in WDS mode i never faced this Layer 2 roaming issue with Avaya wireless phones.
In current WISM all the LWAPs are supporting properly to the Cisco phone and Wirelss laptop clients.
I request you to please let me know how do i proceed further to solve the issue and please let me know if anybugs or incompatibilty for WISM with Avaya wireless phones.
Appreciate your response.
Regards,
KA.

Hello ,
Can any body please respond to my above Query.
Thanks,
KA.

Similar Messages

T540p issue with ThinkPad Wireless 2 x 2 BGN with Bluetooth

Hi,
I have the T540p, an uplifting experience compared to the previous brand I had, however I have been suffering from a recurring issue with the wireless connection.
Once starting up Windows 7 everything works fine except the wifi connection which refuses to connect. Putting the computer to sleep then starting it solves the issue.
I tried to tinker with options to no avail. My technical knowledge is modest so kindly I request support from your esteemed forum members.

Hi,
Welcome to Lenovo Community Forums!
I’m sorry to hear that you have issues with wireless connection in your Lenovo ThinkPad T540p.
If you have Power manager installed, make sure that wireless adapter settings in Power manager is set to maximum performance as shown below.
Also, go to control panel -> Power Options -> Change Plan settings under the power plan you have chosen -> Change advanced power settings -> Make the wireless adapter settings to maximum performance.
Next, go to the device manager, select your Wi-Fi card -> go to Properties -> Advanced -> Set "Transmit Power" to maximum, and "Roaming Aggressiveness" to lowest setting.
Also, under the "Power Management" tab, remove tick for "Allow the computer to turn off this device to save power". And click "OK" to save the setting and reboot the PC.
Hope the above suggestions will help to resolve your concern!
Best regards,
Mithun.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Conference phone with a wireless phone.

VOIP8551B from Philips looks nice but I need a good conference phone in the base unit together with a wireless phone as well. Is there such a set? I am not looking for a USB connected one. I need a one that do not need a computer (usb) to work.

Hi Matt,
There is known defect about DTMF at FXS of UC320W through FXO. We have a beta image which resolves it. If you would like to use it, please send me an email at [email protected] and let me know your CCO ID. I will post the image for you to download.
Best regards,
Wendy Yang

Ever since I received my Macbook Pro in July 2011 I've had issues with my wireless connection at home. After software updates, Apple support suggested I reboot my router which works. But now I have to do it every other day. ????

Ever since I received my Macbook Pro in July 2011 I've had issues with my wireless connection at home. After software updates, Apple support suggested I reboot my router which works. But now I have to do it every other day. ???? AT&T my DSL carrier suggests I get a new router. Apparently the one I have is really old and doesn't support my Macbook Pro. Does this sound right?

If your using WEP encryption yes, Apple has discontinued that becaues it's worthless. WEP (and WPA) is cracked so encryption makes no sense.
Get a new Wireless N router, set it up with WPA2 (AES) Personal and two different 20+ randon letter/numbersymbol character passwords
One for Admin access only of the router, keep this on paper off all comptuers in a safe someplace.
One for entering into devices, computers etc for Internet Access Only.
You need the long and random password to defeat brute force attacks by GPU software that the hackers have now.
Also if you give out the password to another, they can't hack the network with the guest access password.
Computers remember the internet password, so anyone with access to your machines or network will have the password.
Since you have another Admin only password, they can't hack in. got it?
You don't need "Invisible" or "MAC Address filtering" that's a waste of time as hackers can sniff a network and causes issues getting on the network.
Good luck.

Is anyone else having issues with their I Phone 5 running ios 6.1?

As stated above: Is anyone else having issues with their I Phone 5 running ios 6.1?
I am having issues with the WiFi connection to my AT&T router and voice recognition.
It wont make post to Facebook half of the time. It is lacking the option to post videos to Facebook, only to mail, message, and You Tube. And finally the voice recognition messes up what it types in both Siri and messages.

Not having any of those.

Second s5 update has made wifi and data run simutaniously, being charged for data only way to turn off Data is to go to settings. I had same issue with my other phone. Recieved two replacement phones the SIM card did not work on replacements took phone ba

Wifi and Data running simultaneously. Data was being charged to my account even though I was on WIFI. No one can fix the issue. I have wasted 8 hours of my life and went and returned my phone and got a new one yet after the last update I now have WIFI and Data showing that they are running simultaneously. I have looked at numerous message boards and turned off Caller ID don't have Volte on my phone but do get an error with Visual Voice Mail. I don't want any of these services, you are not helping your customers Verizon or Samsung with forcing us to update. I tried not to update my NEW phone that I had to get from Costco because of this exact same stupid issue happen on my last one. But every time I said NO to update the next time I did anything on the phone the UPDATE would pop up again. I would say NO it would come back. I was doing a text and it came up and I hit update not wanting to and then my phone began updating on a low battery. I had to rush to put on charge and then my WIFI and Data came back on together with arrows on all going up and down. I HATE the lack of support I get from SAMSUNG and VERIZON... Verizon washes their hands and say these are not Updates even though these are the features we have on all our phones like Visual Voice Mail and Volte...

I did look at the Settings/Cellular to check the applications. This is one of the steps I did with the person from Verizon who was an "iPhone Specialist". And he didn't see anything unusual. And I can honestly tell you they have very minimal number of apps on their phones.
When I went to the Apple Store the first time with this problem, they had me update the phones iOS systems to see if this would correct the problem. They were each running older versions but different versions. One son had one update to do and the other had a couple of updates needed. So, the problem started before they were updated and they weren't even on the same update. And nothing changed after we did the updates.
I didn't reboot the router and modem, because I'm not having any other issues with my phone, my husband's phone, our iPad, xbox, PS3, or laptops. Would the wifi only affect their phones?

Is anyone having issues with Windows 8 phones not loading mobile versions of websites?

I was just wondering if anyone with a Windows phone is having problems loading the mobile site version of a Muse site when viewed on the phone? or if there is a known bug or incompatability?

Hello, same issue for me.
The site display whith the desktop version.

Issues with Bluetooth/Wireless Mighty Mouse since Snow Leopard Install

Hi,
I am having issues with my bluetooth wireless mighty mouse. It was fine after initially having installed Snow Leopard. However, in the past week it has become progressively more and more unresponsive. It functions perfectly normal for the first while after startup, then after a short period of time it becomes slow to respond to the mouse movements that move the cursor. Eventually it gets to the point that moving the mouse results in no cursor movement whatsoever. It also becomes unresponsive to squeezing the side buttons. There are no issues with clicking or scrolling with the track ball.
I have searched the discussion forums to find issues that pertain to "bluetooth" and "wireless mighty mouse" and have tried the following suggested remedies... Repairing my Mouse with my Mac mini. Renaming my mouse. Deleting the com.apple.Bluetooth.plist file from Macintosh HD\Library\Preferences and restarting my Mac. Reset PRAM and NVRAM. Also tried to install Bluetooth Firmware update 2.0.1 but I get an indication that the update is not needed on my Mac mini. I have also checked for software updates but there are none...
I am going to attempt resetting the SMC but am doubtful that this will help...
Can anyone help... Please... ?
Thanks,
Des

I had read in another forum where someone had an understanding that the bluetooth problem had something to do with Airport/Time Capsule. I had also read about how someone was having an issue with being unable to turn off airport. (I had this same problem.)
Upon deleting a few airport related plist files (see below url) I was able to turn off/on airport AND my Mouse issue has no longer appeared... everything is working a-ok now.
http://discussions.apple.com/thread.jspa?messageID=10125976&#10125976

Is anyone else aving an issue with the "TTY" phone feature with the new ioS 7? Mine will not work in "sleep/lock" mode

Is anyone having trouble with the "TTY" phone answering feature with the new ios 7 when your phone is in "sleep/lock" mode"? I only have an issue when it is in the "sleep/lock" mode

I am sorry..."TTY" in "Phone Settings" being "on" or "off" has nothing to do with this feature but the issue still remains that it only works when the phone is NOT in "sleep/lock" mode

UC520-24U-4BRI-K9 with 7925G Wireless Phones

Good afternoon,
Could somebody tell me if wireless phones 7925 are compatible with uc520? Do I need to have a special version o CME? i've read somewhere that the uc520 also supports the Cisco 521 Wireless Express Access Point. Can somebody tell me if uc520 works with other type of access points (ex: Access point 1250)?
Thanks a lot for your help
Best Regards

Hi Paolo!
Thanks a lot for your answer. just one question: Do I need to have a special version o CME for working with the phones 7925? i think our client got cme 4.1.
Thanks one more time
Best Regards

Does anyone else (or has anyone else) had an issue with their wireless keyboard connecting via the Bluetooth?

The first day I got it, it was fine. Then when I woke up the next day which was less than 12 hours after hooking it up, it wouldn't connect..it let me type a couple of characters to my password, but then literally stopped. My trackpad has yet to have any issues whatsoever. Even during the keyboard malfunctioning it's been fine. In order to get the keyboard to work, I have to log into the guest account, let it be discovered, then pair it. It as now happened on 4 different days, more times than that, though. I've only had it for just over a week. I don't think there's a problem with the computer just because the trackpad is fine. The keyboard blinks that little green light when it's having this issue, too. As you know, it's normally off. Today I tried to log in for the first time and it did the same thing as the first day. It let me type a few characters, then stopped and wouldn't connect. This time, though, when I went into the guest account to let it be discovered it wouldn't let me type the numeric code to pair it. I had to hold down my power button to restart it because I was logged in on another user and it wouldn't let me restart it the normal way without typing the admin username/password...which I obviously couldn't do seeing as how I didn't have a keyboard. Does anyone else think this is a faulty keyboard I need to return? Or is this unfortunately how it works...or what? Help please...
I was at the Apple Store that week 5 times for a messed up phone that they replaced with a total of 4 replacement phones because of different issues the ones they gave me had and driving there that much almost made me say screw it to the iPhone...now I buy this very expensive iMac spending 2 grand and this happens....I'm so mad I am thinking of just returning it and giving up on Apple altogether which Idon't WANT to do...but with all I've dealt with in a 2 week period with the iPhone and now this...oh and I bought a $100 cell phone case I had to replace because it wasn't working correctly. So you see, I am beyond frustartee over Apple.....if anyone could help I'd greatly appreciate it. With all of my problems I've had, you'd think they want to do more than apologize for my inconvenience. Even the techs that helped me said it was ridiculous I've had so many issues and now I'm just adding to the list..

Try this:
Go to System Preferences - Bluetooth. Delete the keyboard from the list of devices by pressing the "-" button. Take the batteries out of the keyboard and reinsert them. In Bluetooth Preferences press the '+" button to add the new device. If the keyboard begins to pair, click the word "pair" and type in the passcode. Press return. The keyboard is now paired.
If the mouse is not pairing, try this: shut down the computer completely, unplug any USB mice, then turn off the power to the bluetooth mouse. ONce the computer starts up again, wait for the pop-up looking for a mouse. Turn on the power to the bluetooth mouse. It should work normally now.

Two issues with HP5514 wireless printer

I have 2 issues that I've had since I installed the Photosmart 5514 a year ago...
I get giberesh on my printouts. Seems to be narrowed down to sending a 2nd doc to the printer while it is printing the first doc. When it gets the 2nd doc, the first starts printing giberesh and the next docs are all giberesh. Power cycle the printer to clear.
The 2nd issue started in the PC after the printer software was intalled. Outlook 2007 will stop loading pictures from the web in my emails. If I kill the hpnetworkcommunicator.exe tasks in task manager, they will start loading. Then when I want to print to the 5514, I have to reboot the pc. The PC is an HP D530 with XP.
I have allowed the updates when the popup says there are updates.
The issues make me limit my use of the 5514 and keep using the older other brand printer.

As i understand, you have a NETGEAR firewall (with DHCP on) and two Linksys routers working as APs. As far as connectivity for internet is concerned, IP address settings as you mentioned for all the three devices is absolutly correct. You didnt mentioned the physical connectivity of 2nd router. Basically, if DHCP is disabled on both Linksys routers then you can either connect both routers to NG firewall (LAN to LAN) or connect first router to NG firewall (LAN to LAN) and 2nd Linksys router to the first router (LAN to LAN).
For the wireless connectivity, you can either keep same SSID or different SSID on both routers, both settings would work since they all the three devices are physically connected and have a single default gateway i.e. NG firewall. However, i would recommend to keep the same SSID on both linksys routers for seamless wireless connectivity.
And last as you mentioned regarding the network name that you cannot see for the first router.
You can upgarde the firmware of the router
And try to change the wireless channel to 6 , 9 or 11 and then try to view the wireless network.

Firefox is in the taskbar, but won't launch. (after having issues with a wireless printer install)

Installed a new wireless printer on my home network. the two desktops running XP-SP2 are fine, but it made a complete mess of my Toshiba laptop, running Windows7.
knocked out the network, disabled my wireless adaptor, turned off the wireless on the laptop and also disabled my Avast anti virus.
Got the wireless enabled on the laptop, recovered and upgraded the anti virus program and got the network connected again.
Can use Explorer, but Firefox will not launch, either from the taskbar or from Start/programs. /they are there, but will not launch.

There may be a corrupted file on Firefox.<br>
Please attempt to perform a clean reinstall. <sup>[https://support.mozilla.org/en-US/kb/forum-response-clean-reinstall (More Details)]</sup> This is different than a regular uninstall.
If a clean reinstall does not fix the issue, please try starting your operating system in safe mode.<br>
To do so, please do the following:
#Ensure that your computer is shut down completely
#Press the power button
#Tap the <code>F8</code> key repeatedly before the Windows logo and startup screen is displayed
#Select Safe Mode With Networking for the advanced startup options list
Please report back with the results of both solutions.

Re: The ongoing saga of text issues with Verizon Wireless

Question, has this problem only occured on smartphones? If so, I'm wondering if you've tried the oh so painful factory data reset, then leave the phone mostly "stock" to see if it happens? A basic tenent of troubleshooting is to try and find a common denominator...wondering if you have a preferred app that may be causing you issues.

jdraper76 wrote:
mrpearsoy,
Thank you so much for your insightful commentary. I am curious to know your credentials that support your statements, how long have you worked for Verizon or with cellular networks?
#1. Maybe I will come by your favorite dining establishment and take a bite of your meal since, well you still get 95%. I don't believe that Verizon will accept 95% of my payment.
#2 Do a little more research, there are far more people experiencing the issue that you suggest. Far more than your 2 to 3 pages.
#3 If I wanted a phone and just a phone I would have bought a plain old phone. It is not a phone and Verizon themselves don't market as just a phone. It is in fact a productivity tool, a media tool, and a whole lot more.
#4 Yes I have used ALL of those phones and then some. I have a dozen phones that are worthy of service, and probably 20 more that are too hold to run on today's networks.
In the future you would be better served to keep your ignorant comments to yourself. I didn't ask for a troll I asked for some assistance with the issue at hand.
And I provided assistance, based on what you told us. And no, I am not a VZW employee. This is a peer to peer forum. Its unfortunate that you arent competent enough to realize that my comments were not ignorant. It was based on information that YOU the original poster, provided. However, I did know in advance that you would have something SMART to say seeing as how I shot down your post. Im sure others would have as well, but nobody else took the time to post on your post, because they know that you are just complaining for the heck of it. I hope you do indeed now pay your etfs and post. More bandwith for others texts to go through. Troll, INDEED! Clown.

Issue with new 9300 phone and Vodafone service

Hi All,
My name is Amol Supal.
I am for Mumbai, India.
I have bought new Blackberry 9300 curve from E Zone Chembur Branch, India.
I took Vodafone new connection and try to activate Blackberry service.
But Vodafone service centre convey me that you phone is not able get register in Blackberry Server.
Request you all, help me to resolve this issue.

Hello,
You will need to work with Vodafone...only they can look "behind the scenes" to see what is going on. Perhaps if they tell you why it is not able to register, that may provide some better hints as to what is going on.
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

L2 Roaming issue with Avaya wireless phone on WISM -V6.0.196.0

Similar Messages

Maybe you are looking for