L2TP VPN doesn't work (IVPN software as server)

Hello,
I am having problems to setting up VPN connection from win XP to my MBP (WAN connection).
I use IVPN sofware on my MBP as VPN server config software. All my software and firmware are up to date.
All the right ports are mapped in my AEBS (means 1701, 1723, 4500 and 500).
When I try my VPN connection from LAN to LAN it works fine (L2TP and PPTP).
When I try from WAN it is not working at all.
The win XP things says : "error 678 : no response" or sometimes "timed out".
My WAN Ip is static, my LAN IP's too.
I've tryed the DMZ (default host) workaroud, but still no results.
Does the AEBS really VPN passthrought? Cause some forums says it's not...
Please help.
A very old mac user (since 24 years).
Thanks.
Phil.

shinzonqc wrote:
I've tryed the DMZ (default host) workaroud, but still no results.
Does the AEBS really VPN passthrought? Cause some forums says it's not...
I do not believe the AEBS completely supports passthrough traffic (even though it's supposed to). The thread over here: http://discussions.apple.com/thread.jspa?messageID=4046689 would seem to indicate that many people are having problems with VPN.

Similar Messages

  • VPN doesn't work

    I just switched from Cable Internet to Verizon high speed.  Internet and e-mail work fine, but my Cisco VPN doesn't work with Verizon.
     Thus I can't connect to my servers at work.
    I know my VPN works good because I travel alot and it works in every hotel I stay at, in fact I just tried it down the street through WiFi.
    Does anyone know the fix for this?

    Easy solution......
    Bridge mode is achieved by 2 easy steps:
    1) - Log into the GUI
    click the My Network Icon on top
    Click Network Connections on the left
    Click on the words "Broadband Connection (DSL)"
    Make the Protocol dropdown say "Bridge"
    Make the Bridge Mode dropdown say "Bridge"
    Save - the unit will reset
    2) Log back into the GUI
    Click the My Network icon on top
    Click Network Connections on the left
    Click the on the word "LAN"
    Remove the top checkmark (you want to not enable the DHCP Server)
    Make sure the modems ip address is not going to be the same of your router
    Save
    Exit the GUI
    I made my modem 192.168.10.1, and my routers lan network is 192.168.0.1
    The 6100F is bridged. The internet light will stay out. Whatever the next device on the network is will need to do the PPPoE connection (with your ISP username and password) ex your router
    Myk

  • My VPN doesn't work ever since I upgraded to iOS7

    My VPN doesn't work ever since I upgraded to iOS7, pls help?

    It's been a problem with ios 7, for now try using your apple id for it. Apple is supposed to be putting out a fix for it soon.

  • E-mail notification doesn't work after software upgrade

    Based on the recommendation of a sales rep; I did the software upgrade yesterday and have had nothing but problems.  All the e-mail accounts didn't work.  So I spent an hour getting my e-mails setup and guess what?
    Even though I have it setup to check every 10 minutes; it doesn't work.  I have to manually go to each account and click on the 2 arrows to check.  I used to get a flashing blue light on my phone when I had a new e-mail; now I don't.
    What's going on???????????????

    Hi, I did all you mentioned but still same error messages
    Oct 25 14:16:42 xxx /Applications/Server.app/Contents/ServerRoot/usr/bin/amavisd[16427]: Using primary internal av scanner code for ClamAV-clamd
    Oct 25 14:16:42 xxx /Applications/Server.app/Contents/ServerRoot/usr/bin/amavisd[16427]: Deleting db files __db.001,__db.002,__db.003,__db.004,nanny.db,snmp.db in /Library/Server/Mail/Data/scanner/amavis/db
    Oct 25 14:16:42 xxx/Applications/Server.app/Contents/ServerRoot/usr/bin/amavisd[16427]: Creating db in /Library/Server/Mail/Data/scanner/amavis/db/; BerkeleyDB 0.54, libdb 4.7
    Oct 25 14:16:43 xxx /Applications/Server.app/Contents/ServerRoot/usr/bin/amavisd[16427]: initializing Mail::SpamAssassin (0)
    Oct 25 14:16:43 xxx /Applications/Server.app/Contents/ServerRoot/usr/bin/amavisd[16427]: SpamAssassin debug facilities: info
    Oct 25 14:16:43 xxx /Applications/Server.app/Contents/ServerRoot/usr/bin/amavisd[16427]: (!!)TROUBLE in pre_loop_hook: config: no rules were found!  Do you need to run 'sa-update'?
    Suicide () TROUBLE in pre_loop_hook: config: no rules were found!  Do you need to run 'sa-update'?
    I removed all spam filters and mail works without, which is not so good but seems to be the only way at the moment.
    Any other idea or should I just reset the whole installation?
    Thanks for your feedback.

  • Nokia 5800 doesn't work after software update

    hi,
    couple of hours ago i downloaded ovi suite to update my phone's software. then my phone restarted as it was supposed to ,at first it didn't accept my lock code,and now it doesn't work AT ALL.  i tried everything,all i see is the blue "nokia" thing then it freezes. it would be awesome if anyone could help. Thanks in advance.
    Solved!
    Go to Solution.

    Try a hard reset
    http://friedbrains-friedblogs.blogspot.com/2009/02/3-finger-salute-for-5800-full-hard.html
    It WILL sort it 
    Good Luck
    If I have helped at all, a click on the White Star is always appreciated :
    you can also help others by marking 'accept as solution' 

  • VPN doesn't work anymore after 10.6.2 update

    Hello to all,
    I've a MacPro with 10.6 SnowLeopard server, and until yesterday all was great with 10.6.1.
    After update to 10.6.2 plus some airport update, VPN dooesn't work.
    Could someone help me?
    I use the firewall on Airport extreme (the latest model) and automatically forward VPn setting from SLServer Firewall.
    Why it don't go anymore?
    thank you to all for help
    Marco
    Italy

    so, I'm trying from home to use VPN:
    - if I try from usual user, doesn't work
    - if I try from Server Administrator credentials (user + password) it works
    Of course I need to use VPN from "normal" client users, not with Administrator credentials
    Another strange issue is: in VPN netwotk configaration (client, preferences, network) if I put name and password about one user the 2 field become locked and I must erase that VPN connection and create it again.
    If I put the administrator name+psw, the 2 field remaining accesible and unlocked.
    I think in Apple they made a very bad job with 10.6.2 and VPN!
    has someone any suggestion?
    Marco

  • VPN doesn't work since I reset permissions

    Hi .
    Recently I reset my permissions via disk utility app, Since I did that, VPN doesn't connect on my mac. it works with same VPN information on my iPad & iPhone so the problem is not from VPN.
    I'll be glad if you could help me.

    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings      
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                 
    iOS: How to back up                                                                
    - Restore to factory settings/new iOS device.             
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem. Other users have had the same problem.
    Apple Retail Store - Genius Bar                                      

  • PPTP VPN doesn't work on iOS 6

    I just tried to set up my iPad 2 (on iOS6) for an already working PPTP VPN server on my DD-WRT and found out that it doesn't work anymore (apparently somethings changed after iOS 4.3 according to tons of blogs on the net) There seems to be a few solutions about adding a couple entries to /tmp/pptpd/options.pptpd but none of these worked for me on iOS 6. Is there anyone knows a solution to this problem?
    Note: nopcomp, noaccomp, default-asyncmap, mru 1400, mtu 1400 options do not work nor doesn't seem to help a bit at all, by looking at the dd-wrt log output. Most people claim these options make it work for iOS 5, but didn't work for me.

    Yeah, resurrecting old thread here...
    I was having similar problems with iOS6 and my DDWRT running on Buffalo WZR-600DHP.  After I changed the mtu & mru to 1400, it worked.  It was driving me nuts before.

  • Apps and media library doesn't work after software...

    Hey guys!
    Few days ago I updated my C3-00's software and my apps (Opera Mini and Facebook) doesn't work anymore. I tried reinstalling Opera but when I try to open it it says Opening Application and immediately after that Closing application (same with Facebook client).  
    My second problem is that my media library is messing with me because it maps the song artist and titles (484 songs) and only the few ones within a folder is played over and over. E.g. I try to play Queen - I want it all but Pendulum is played besides that.
    Thank for helping

    Read
    http://support.apple.com/kb/ht1808

  • Changed the Shared Secret, and now VPN doesn't work...

    Hello all. So our VPN was working fine. I changed the Shared Secret, and it stopped working. Seems like any Shared Secret now that I use doesn't work, and I've been triple-checking it on both the server and clients to make certain that it's not miss-typed.
    It seems to connect OK, but then it fails to authorize. I've got the proper ports open, and again, it worked just fine with the first Shared Secret I used.
    Is there something I'm missing about Shared Secrets here? You should be able to change them when you need too, right?
    Message was edited by: Jeffrey McGrew

    Looking at the logs I'm seeing something strange that I don't understand. It appears that one part of the authorization is succeeding, and another part failing:
    "DSAuth plugin: Could not authenticate key agent for encryption key retrieval."
    Then, two lines later:
    "CHAP peer authentication succeeded for USER"
    "DSAccessControl plugin: User 'USER' authorized for access"
    But then the client never shows that it's authorized. So is this a problem with the client configuration, since the server is showing an authorized session starting, or is there something wrong with the DSAuth Plugin?
    (going to read more PDFs)

  • Client VPN doesn't work until reload; all other services are fine

    We have a 1800 router running 12.4.x that is acting up.  Every week or 2, client vpn connectivity stops working on it (clients receive a ' reason 412; the remote peer is no longer responding' when trying to connect).  All other traffic running through that router continues to work fine (site to site, nat, etc).  If we run a 'clear ip nat translation', then ONE client can reconnect, but any subsequent clients cannot.  So, basically one at a time.  the only 'fix' is a reboot of the router.  any suggestions on where to start troubleshooting?
    thanks!                  

    Matt,
    Did you disable NAT-T on this device?
    http://www.cisco.com/en/US/products/ps6120/products_tech_note09186a00807e0aca.shtml#solution01
    Thanks,
    Tarik Admani
    *Please rate helpful posts*

  • PHP's mail() function doesn't work as under Lion Server

    Since I've upgrades to OS X Server (10.8) my web-based contact form became essentially useless since the PHP function mail() didn't work anymore. There was a lot of traffic during those days and I bet I lost a lot of messages because of it. Does anyone have a remedy or a working example PHP script that works in OS X Server (10.8)?

    From my understanding, trying to save apple server specific attributes on Active Directory users in the WGM will not work unless the AD schema has been extended to include these attributes.
    What you can do in leopard server is to export the list of AD users in WGM and then import them into open directory in WGM.
    From my testing the open directory will automatically authenticate with AD for those imported users. You can save Apple server attributes on those imported users.
    Message was edited by: Kwong Kian Tew

  • L2TP VPN connection not working under 10.6.3

    Hi everyone.
    I need to connect to a VPN with L2TP/IPSec.
    The connection works fine if I boot into Bootcamp (win7).
    But if I boot into 10.6.3, it does not work.
    any idea what the problem could be.
    Settings are triple checked and copy pasted into their proper fields (like in win7). router settings are correct, otherwise it would not work in win7.
    So it is a problem with osx.
    The following is out of the ppp.log:
    Thu Apr 22 19:14:03 2010 : L2TP connecting to server 'vpn.xxx.com' (x.x.x.x)...
    Thu Apr 22 19:14:03 2010 : IPSec connection started
    Thu Apr 22 19:14:03 2010 : IPSec phase 1 client started
    Thu Apr 22 19:14:03 2010 : IPSec phase 1 server replied
    Thu Apr 22 19:14:04 2010 : IPSec phase 2 started
    Thu Apr 22 19:14:34 2010 : IPSec connection failed
    the server is reachable, but something fails in phase 2.
    in the system log, the entry is:
    Apr 22 19:14:03 noname pppd[517]: pppd 2.4.2 (Apple version 412.0.10) started by x, uid x
    Apr 22 19:14:03 noname pppd[517]: L2TP connecting to server 'vpn.xxx.com' (x.x.x.x)…
    Apr 22 19:14:03 noname pppd[517]: IPSec connection started
    Apr 22 19:14:03 noname racoon[518]: Connecting.
    Apr 22 19:14:03 noname racoon[518]: IKE Packet: transmit success. (Initiator, Main-Mode message 1).
    Apr 22 19:14:03 noname racoon[518]: IKE Packet: receive success. (Initiator, Main-Mode message 2).
    Apr 22 19:14:03 noname racoon[518]: IKE Packet: transmit success. (Initiator, Main-Mode message 3).
    Apr 22 19:14:03 noname racoon[518]: IKE Packet: receive success. (Initiator, Main-Mode message 4).
    Apr 22 19:14:03 noname racoon[518]: IKE Packet: transmit success. (Initiator, Main-Mode message 5).
    Apr 22 19:14:03 noname racoon[518]: IKEv1 Phase1 AUTH: success. (Initiator, Main-Mode Message 6).
    Apr 22 19:14:03 noname racoon[518]: IKE Packet: receive success. (Initiator, Main-Mode message 6).
    Apr 22 19:14:03 noname racoon[518]: IKEv1 Phase1 Initiator: success. (Initiator, Main-Mode).
    Apr 22 19:14:03 noname racoon[518]: IKE Packet: transmit success. (Information message).
    Apr 22 19:14:03 noname racoon[518]: IKEv1 Information-Notice: transmit success. (ISAKMP-SA).
    Apr 22 19:14:04 noname racoon[518]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1).
    Apr 22 19:14:04 noname racoon[518]: IKE Packet: receive success. (Information message).
    Apr 22 19:14:07 noname racoon[518]: IKE Packet: transmit success. (Phase2 Retransmit).
    Apr 22 19:14:08 noname racoon[518]: IKE Packet: receive success. (Information message).
    Apr 22 19:14:10 noname racoon[518]: IKE Packet: transmit success. (Phase2 Retransmit).
    Apr 22 19:14:10 noname racoon[518]: IKE Packet: receive success. (Information message).
    Apr 22 19:14:13 noname racoon[518]: IKE Packet: transmit success. (Phase2 Retransmit).
    Apr 22 19:14:13 noname racoon[518]: IKE Packet: receive success. (Information message).
    Apr 22 19:14:16 noname racoon[518]: IKE Packet: transmit success. (Phase2 Retransmit).
    Apr 22 19:14:16 noname racoon[518]: IKE Packet: receive success. (Information message).
    Apr 22 19:14:19 noname racoon[518]: IKE Packet: transmit success. (Phase2 Retransmit).
    Apr 22 19:14:19 noname racoon[518]: IKE Packet: receive success. (Information message).
    Apr 22 19:14:22 noname racoon[518]: IKE Packet: transmit success. (Phase2 Retransmit).
    Apr 22 19:14:22 noname racoon[518]: IKE Packet: receive success. (Information message).
    Apr 22 19:14:25 noname racoon[518]: IKE Packet: transmit success. (Phase2 Retransmit).
    Apr 22 19:14:26 noname racoon[518]: IKE Packet: receive success. (Information message).
    Apr 22 19:14:28 noname racoon[518]: IKE Packet: transmit success. (Phase2 Retransmit).
    Apr 22 19:14:28 noname racoon[518]: IKE Packet: receive success. (Information message).
    Apr 22 19:14:31 noname racoon[518]: IKE Packet: transmit success. (Phase2 Retransmit).
    Apr 22 19:14:31 noname racoon[518]: IKE Packet: receive success. (Information message).
    Apr 22 19:14:34 noname pppd[517]: IPSec connection failed
    Apr 22 19:14:34 noname racoon[518]: IKE Packet: transmit failed. (Information message).
    Apr 22 19:14:34 noname racoon[518]: IKEv1 Information-Notice: transmit failed. (Delete ISAKMP-SA).
    Apr 22 19:14:34 noname racoon[518]: Disconnecting. (Connection tried to negotiate for, 31.609591 seconds).
    Apr 22 19:14:34 noname racoon[518]: IKE Packets Transmit Failure-Rate Statistic. (Failure-Rate = 7.143).
    Apr 22 19:14:34 noname racoon[518]: IKE Information-Notice Transmit Failure-Rate Statistic. (Failure-Rate = 100.000).

    Hi
    i have the same messages on 10.6.4 and with the sonic xx170:
    28.06.10 11:39:04 racoon[489] IKE Packet: transmit success. (Phase2 Retransmit).
    28.06.10 11:39:07 racoon[489] IKE Packet: transmit success. (Phase2 Retransmit).
    28.06.10 11:39:08 racoon[489] IKE Packet: receive success. (Information message).
    28.06.10 11:39:10 pppd[488] IPSec connection failed
    28.06.10 11:39:10 racoon[489] IKE Packet: transmit success. (Information message).
    28.06.10 11:39:10 racoon[489] IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA).
    any ideas?
    waiting on 10.6.5, 10.6.6 ....?
    regards, Arthur

  • VPN doesn't work at build 10049

    VPN has worked at previous builds but not anymore at build 10049.
    When I choose VPN-network provider whole Settings-windows shuts down.

    Hi fiantsirk，
    There have been some known issues in Windows 10 build 10049:
    No access to Internet Protocol (v4 or v6) in 10049
    VPN configurations might be affected, folks here have found out some ways to make it work (3rd-party software related), you may check at :
    https://social.technet.microsoft.com/Forums/en-US/261392a2-3914-4518-acb4-065a0a635f58/build-10049-breaks-openvpn-there-are-no-tapwindows-adapters-on-this-system?forum=WinPreview2014General
    Best regards
    Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

  • Re: VPN doesn't work on my new Portege Z830

    I recently bought a portege z830. I installed watchguard firebox vpn connection software but i can not establish a vpn connection. I enter the username and password, the program seems to make a connection but it disconnects immediately. There's no problem with the password or username.
    The software works fine in other notebooks. The OS on the machine is Windows 7 Prof.(X64).
    Thanks

    I really dont know if described issue has anything directly with your new Portege. I presume you need this for your business or you must use it in your company so I strongly recommend you to speak with your local administrator and check what can be done about it.
    On this virtual way it is not easy to say what is wrong there. On my Satellite P500 I use Cisco AnyConnect VPN client and it works perfectly with preinstalled original Toshiba recovery image. It is Win7 64bit Home Premium.

Maybe you are looking for