L655 has solid white power LED and soid orange battery LED and will not power on at all.

L655 has solid white power LED and soid orange battery LED and will not power on at all.  I tried a second power adaper.  Any other suggestions?  It does not even try to power on.  No fan or any other noises.

if it is not powering up on battery or AC, then there is either something wrong on the motherboard keeping it from powering up, or a bad power switch.  I personally have not encountered a bad power switch on any of my Toshibas, so I would suspect something with the motherboard.  It is strange that it does indicate that your plugged in and charging.  If you leave the power adapter plugged in, does the battery status eventually go white?
Qosmio X875 i7-3630QM, 32GB RAM, OCZ SSD Qosmio X505 i7-920XM, PM55, 16GB RAM, OCZ SSD
Satellite Pro L350 T9900, GM45, 8GB RAM , Intel 320 SSD (my baby) Satellite L655 i7-620M, HM55, 8GB RAM, Intel 710 SSD (travel system)

Similar Messages

  • After unplugging and moving my pxi-1002 it will not power on

    need to get this thing powered back up ASAP. have presentation using it on thursday.

    I'll let you know of some possible reasons for this, but I might need more information to go off of. I'll just list off my thoughts:
    1. The chassis is just not getting power: It isn't plugged in, that particular outlet is bad, a surge protector is not working correctly, etc. You mentioned moving the chassis, does it work back in its old location?
    2. There are no modules plugged into the controller: I don't have a 1002 to check this, but I know that the 1006 will not power on unless the minimal load is met... meaning it needs to have a module or controller actually in the chassis.
    3. Too much power draw from module: If a pin was bent somehow causing a short to ground, that could be a possible problem. Or, a particular module just might have issues by
    itself. What do you have in your chassis? Try removing everything but the controller. If it boots up, then you can shut down and insert different modules to isolate the problem.
    If none of this helps, let me know and I'll see what else I can find out. Any information you can provide would be great. I hope this gets worked our before Thursday.
    Best Regards,
    Jeremy R.
    NI - Applications Engineer

  • Iphone 4 will not power on and is not charging

    iphone 4 was charged and suddenly stopped work went dark,  Will not power back on, will not charge.  Any suggestions on cause or fix???

    Hi daj1202,
    That definitely doesn't sound good. Lets see if we can isolate this issue further:
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/TS2802
    Will not turn on, will not turn on unless connected to power, or unexpected power off
    Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
    Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIs and corrosion.
    Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
    After at least 15 minutes, if:
    The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen. Then unplug the phone from power. If it immediately turns off, seek service.
    The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
    Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
    If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
    If the display turns on, go to step 4.
    If the display remains black, go to next step.
    Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
    If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
    Thanks,
    Matt M.

  • Z22 will not power on

    My z22 has been idle.  After charging for 3 hrs. - still will not power on.  I have done the "soft" reset and still will not power on.  Any sugestions?
    Post relates to: Palm Z22

    hdtrude,
    Is this a new z22 or is it on which you have stored information?  If it is new, a "hard reset" is worth a try.
    Are you using the charger that came with the z22 or are you using the USB cable to connect the z22 to your computer for charging?
    Post relates to: Palm TX

  • My IPOD Touch initially had a white screen.  I tried correcting this by restoring default settings via ITunes.  The Restore Failed with error 1602 and now the IPOD touch is completely dead. It will not power on or respond when I plug it into my PC via USB

    My IPOD Touch initially had a white screen.  I tried correcting this by restoring default settings via ITunes.  The Restore Failed with error 1602 and now the IPOD touch is completely dead. It will not power on or respond when I plug it into my PC via USB.  I get an error on my PC stating that device attached to USB port is not recognizable.  Can anyone help?

    Error 1602: Try the following steps to resolve this error:
    Ensure proper USB isolation troubleshooting has been performed, and test with a known-good cable.
    Follow the steps listed for Error 1604.
    This error may be resolved by disabling, deactivating, or uninstalling third-party security, antivirus, and firewall software. See steps in this article for details on troubleshooting security software.
    Above from:
    http://support.apple.com/kb/TS3694

  • My iPod has a white screen.  After holding down the middle and the menu button it goes black, then back white, and then beeps twice but stays white.  It never shows the apple logo, just stays white - help!

    My iPod has a white screen.  After holding down the middle and menu button, the screen goes black then back to white and beeps twice.  I have returned to original settings and resorted content to no avail.  I still have a white screen.  I have plugged it up and tried resetting again and again, still a white screen with two beeps - help.

    I have the same exact issue. Fifth generation iPod Nano, blank screen, Restore had no effect. I'm running Windows 7 Home, with all software up-to-date. I suspect hardware damage. Any clarification would be appreciated. Thank you in advance.

  • HT1414 Hi there, my I pad series 2 has a black screen, it will not power up when attached to a laptop, and only shows black screen and Apple icon when attached to a mains power source. Any thoughts please? Allan

    Hi there my Ipad 2 has a black screen, will not power up and will only have an Apple icon when plugged into a mains power source. It will not power up when connected to a laptop. Any thoughts please?
    Regards,
    Allan

    Hi there,
    You may find the troubleshooting steps in the article below helpful.
    iOS: Not responding or does not turn on
    http://support.apple.com/kb/ts3281
    -Griff W. 

  • My iphone 4s without warning has powered off and will not power back up? any suggestions?

    My iPhone 4s has just powered down without any previous indication of problems and will not power back up? Any suggestions?

    Connect iPhone to Wall Charger for 10 minutes, it may turn ON itself. If still nothing keep on Charger and Reset, hold both home and power buttons for about 20 seconds until the iPhone begins to start.

  • Iphone 4s has vertical lines all across the screen and will not power down unless it is charging. What is the problem here?

    My iphone 4s recently stopped turning on. I left it alone on the charger for a few days and now will power on just fine. However I have vertical lines going across the entire screen. I also noticed that it will not power down and stay off unless it is connected to the charger. Is this a hardware problem?

      Try to Reset your device. 
    Press and hold both the Sleep/Wake button and the Home button for at least ten seconds, until the Apple logo appears (ignore the Slide to Power Off option that shows up first).

  • Ibook abruptly lost power and will not power on

    I have a G4 Ibook. I have had it since Jan 06. I just got it back from having the optical drive replaced since it quit last April. All was working fine for just less than a day when it abruptly lost power and will not power on at all. The company did the repairs has trouble shot try to power it up and is arranging for us to ship it back. Any ideas of what it could be, and the likely hood it is related to the upgrade vs. a fluke occurrence that I will have to pay additional money to fix?
    CG

    It's hard to say for sure, but if the iBook powered up perfectly before the repair and didn't power up after the repair, you could argue that the upgrade caused the problem and it shouldn't be extra for them to fix it. I'm guessing, but the power input and the battery are in the vicinity of the drive, and it seems likely that something wasn't properly assembled or got damaged and that is what led to the failure. I wouldn't expect an independently occurring fluke.
    Good luck!

  • MacBook will not power on and no start up sounds

    My MacBook will not power on despite having a fully charged battery and the power cord has a green light. I used all of the support suggestions online and spoke with an apple care rep. I was told that it seemed as though it was a power flow issue- the power button is not responding properly. I was also told that it doesn't seem like it is affecting my hard drive since there are also no start up sounds.
    My question is, is this problem fixable if I choose to sell the MacBook? And how costly is the solution?

    Sorry about Necroing a 1 year old thread but I am having the same issue with the same Model. Laptop went dead overnight, no led indicator of power. Opened the laptop and tested the AC adapter. I get 19.5V exit on the cable. Tested the power connector on the motherboard and getting the same voltage. Capacitator to not seem damaged. Any suggestion on how to troubleshoot this further? I love that laptop

  • My iPhone 5s will not power on and I need my serial number for support.

    I am attempting to get help through Apple Support- Chat, but I need my serial number.  It is not showing up in iTunes under the device preferences.  Any other ways to retrieve the serial number through iCloud?
    If anyone has any idea of what is going on with my phone, I would love some assistance.  I live 45 minutes from the nearest Apple Store.  Here's the situation:
    About 2 weeks ago, my phone started shutting itself off and restarting randomly.
    About a week and a half ago, I would randomly get a blue screen and then the phone would restart multiple times.
    About a week ago I turned off Touch ID in an effort to resolve the issue, after reading some fixes from this community.  That seemed to help.  I do have the animation turned off, so I had read that there may be an issue between the Touch ID and animation reduction.  If that had not helped, I was going to turn the animation back on.
    Last night my phone seemed fine.  I did hear it restart in the middle of the night once, but this morning it will not power on at all.
    I tried connecting it to my computer through iTunes, but iTunes does not see it and I cannot access the device information from it.
    My phone is less than a month old, and for the first two weeks it worked great.  I am taking it into the AT&T Store today where it was purchased, but I don't really have high hopes for a resolution.
    Any help is much appreciated!

    Sorry AT&T store won't be much help.
    I suggest you make an appointment with the Genius bar and then go to the Apple store.

  • HT4061 My iPhone 4 does will not power up once I have turned it off.  When I try to charge it in the off position I only get "pinging".  Has anyone else had this problem?  If so, what is the remedy?

    My iPhone 4 does not/will not power up once I have turned it off.  When I try to charge it in the off position, the screen remains black and I only get continuous pinging tones.  Has anyone had this problem?  If so, what is the remedy?

    Thanks so much but none of that helped.  It was driving me crazy because it would back up another external drive.  I just changed the name of the drive from iPhoto/iTunes Library to Media Libraries and IT WORKED!! I guess for some reason it didn't like the drive being called iPhoto or iTunes ???? I don't understand but I have tried so many solutions and exchanging things out but the name change did it????!!!
    Thank you for your help and replying to this.  Guess I made my own issue!

  • T60 will not power up (battery status led green, power status led green)

    Ok so I have been researching this for a couple days now. Trying various things............
    Including the famous 10 second power button press discharge.........
    Symptoms:
    1st Disclaimer - coffee was exploded all over the laptop but has been running for a month.
    Symptoms:
    It has been working post coffee spill (several weeks ago) as long as you left it running. I get cocky and turn it off then it wont come back on.
    The laptop has exhibited the inability to power on since but I have been able to get it  to turn on several times since.
    green power light comes on with AC adapter only
    plug battery in and the battery light goes green
    press the power button - both lights go out
    I replaced the keyboard, battery, tested for 20 Volts on the AC adapter, tested for 2-3 volts on the CMOS battery.
    I tried testing for 20 volts on the motherboard where the power supply cable connects. I have most of the laptop broke down still.
    I did get it running again last night as a result of me incorrectly using the multimeter and short circuiting the power supply connector .
    It booted up and ran fine and I even tried turning it off and on again several times.
    I thought it might be a heat issue. I turned it off and tried to turn it on this morning and it will not power up.
    Same symptoms as before.
    no battery, only power connected, green light comes on, plug in the battery, battery light goes green, try to turn it on and the lights go out.
    It seems like it is fixable but I am not sure what to look for next.
    Or should I be looking for another system board...........if so what should I replace it with
    This is an IBM T60 Type 2613 15" screen.
    Solved!
    Go to Solution.

    Welcome to the forum!
    Your best bet would indeed be a new system board. Any single one from a non-widescreen T60/p will work.
    I've got dozens of them available - send me a PM if you're interested.
    Good luck.
    Cheers,
    George
    In daily use: R60F, R500F, T61, T410
    Collecting dust: T60
    Enjoying retirement: A31p, T42p,
    Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
    Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

  • TS1713 My mac sometimes will not power up even though it is fully charged and no matter how many key's I touch will not bring it on. It comes on after about 10 minutes and I have to shut down about 6 windows before I can open up a browser.

    My mac will not power up even though it is fully charged. It only happens occasionally and when I try to power up after about 10 minutes it comes to life but has 6 or 7 windows that I have to close in order to open up my browser.

    1. Reset PRAM.  http://support.apple.com/kb/PH4405
    2. Reset SMC.     http://support.apple.com/kb/HT3964
        Choose the method for:
        "Resetting SMC on portables with a battery you should not remove on your own".
    3. Start up in Safe Mode.
         http://support.apple.com/kb/PH11212

Maybe you are looking for

  • Video not showing in WMP ActiveX control

    Trying to play an MP4 in Windows Media Player and I get a black control and WMP acts as if it is playing.  The MP4 does not have audio but other posts have suggested this is not affected by this issue.  I have tried all of the various solutions from

  • Songs greyed out in iTunes on iMac

    I have an album that I have played previously with no problem. Now, all the songs appear greyed out on my iMac and the album will not play. I can double-click on individual songs to play them but I can't play the album, nor will iTunes play the follo

  • How can I get my embeded video to play on the IPAD?

    Hi, I added a video to my PDF by clicking interactive objects > Video.  I then needed to convert the video using Adobe media encoder which I did successfully to a .f4v file and now it will not play on my Iphone/Ipad.  What sort of player to I need to

  • Problem with "import sabasrv.database.*;"

    Hi there.. I am new to the Java game so this is probably a very easy problem to fix. I am using the Forte IDE and My code has the following imports : package sabasrv.user; import javax.servlet.*; import javax.servlet.http.*; import java.io.*; import

  • Module pool screen field should default without pressing enter

    Hi I have got a main module pool screen which has a tabstrip with four tabs. There are 2 fields in the main screen when we select from F4 for the first field then the field 2 should default in case of a condition. This happens only when i press enter