L7600 Cannot Access via browser

I'm frustrated.
HP Printer --> Wireless Bridge --> Router
I can print from my MAC and the HP Utility can access the printer so I know I have connectivity. However, driectly access the printer via the browser seems impossible. I know I have the correct IP address and netword otherwise I could not print nor would the HP Utility "see" the printer. Any ideas - my PC cannot "see" the printer either.
Thanks,
BGI

Router - Linksys E3100
Reserved DHCP for the pinter xxx.127
Access Point - WET650N - DHCP off using static IP
I can print from my Mac using the xxx.127 IP adresss and the HP Utility can connect to the pinter and print the configuration page. However, I cannot access the printer via the browser.

Similar Messages

Cisco 1262 AP cannot access via cosole and GUI

Hi,
I have a Cisco AIR-LAP1262N-E-9 but I cannot access via console and GUI. Also, I noticed that after getting IP address from DHCP server, its IP address will be released after 2minutes. Then after a while, the access point will get another new IP address. And this happens repeatedly.
Hoping for some help out there...
Thanks,
shawn

Hi Manas,
Thanks for your comments.
I have a WLC 5508 controller. I just want to have a basic setup for my upcoming project implementation. On my test bed, I have WLC, 2 sets of AP, and PoE L3 switch. The L3 switch serves as a DHCP server to APs. I manually set the Management Interface IP address of WLC in the same VLAN of the DHCP scope for AP just for basic connectivity. Upon powering up the APs, the WLC detected the APs. However, after 2-3 minutes, the WLC cannot detect anymore the APs. I also notice that the APs are getting their IP address to DHCP server but it will release after sometime..may about 3minutes. Then the APs will get again IP address and will release it. And this happens continuously. I just wish to hard code the IP settings to APs via console but I cannot access it.
Hoping for your help and thanks in advance.
Regards,
Shawn

How do i remove my old apple id from an old iphone...i cannot access via email nor security questions, pw does not work.

I got rid of my old iphone and opened new apple id and pw on this new ip4s. I cannot access the old apple ID via usual
access ie., security questions, password or email verification. The email never arrives and when I answer the security it states incorrect answer.
I just want to delete that old apple id account for security reasons, hackers, thieves, potential unknown risks.
Please advise.
Thanks.
C.

The Apple ID exists. The email address you used to create it may not, but the Apple ID does. Call AppleCare and ask to speak to someone in account security.

Portal not accessable via browser as inside sapmmc - http provider is red

Hi Experts,
I am very new to NW admin side and currently my client is facing an issue while accessing portal via browser.
Problem: Some times suddently when users try to access production portal it takes a lot of time to open up and in most cases it doesn' t get opened up at all. To check what' s wrong with the portal i access sapmmc and inside their i find under current status -> ... -> services -> http provider -> total requests in red status with a description as avg request - response time last reported value above threshold limit. It will be the same case under open alerts too.
My server configuration is:
SAP-JEE = 7.0SP14
OS = Windows 2003 (X86) 5.2
Server Version = 1.4.2_17-bo6
Kernel Version = 7.00 patch level 109886.44
Server = 32 bit
RAM = 16.00GB
Processor = Intel(R) Xeon(R) CPU E5450 @3.00GHZ (8CPUs)
Heap Size: 1024 MB
Approximate number of users = 500 - 600
Currently to solve the issue, we give a reboot to server. But with the progress in time the frequency is getting increased drastically (approx once in 2- 3 days).
Any pointers on how to solve this issue will be greatly appreciated.
Thanks In Advance,
Vipin.

Hi all,
Thanks for your valuable inputs!
Now the issue seems to end up by raising an OSS notes with SAP and i have been given responsibility to prepare a doc that needs to be submited to SAP.
I have already got the screenshots from SAPMMC on it' s status and all, but also requires log information specific to the reason behind this behaviour. Can i know where the log information specific to such issues gets logged and all the necessary information that i need to document to raise an OSS.
Inputs with be of great help and will be highly appreciated.
Thanks In Advance,
Vipin.

WRT160n cannot access via web browser

After i unchecked the acces the router through web browser box and saved setttings now I cannot get back in. I know this was a dumb mistake. I did this so I counld access my web cam. Every time I tried to access the cam the router sign in screen came up. Well now the cam orks but not the sign in screen. Please help. I really don't want to push reset because I don;t remember the settings AT*T told me to change to use the router with their Modem.

Are you getting any error message...?
Are you trying to access the router's setup page...?
If you want to access the router setup page then,Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...If you setup your own password and you don't remember the password then,you have to reset the router.

Firefox just quit on me. I cannot access the browser home page

When I try to use my browser this is what appears: Unable to connect to the server at www.mozilla.com, the site could be temporarily too busy, check your network connections(which I did), if your computer is protected by a firewall or proxy make sure firefox is permitted to access the web. This is my problem It won't let me get to the web.
== User Agent ==
Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.1; WOW64; Trident/4.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; Media Center PC 6.0)

https://support.mozilla.com/en-US/kb/Firefox+cannot+load+websites+but+other+programs+can
If you just updated to Firefox 3.6.'''6''' - a new preference was added to the Connection Settings proxy preferences in Tools > Options > Advanced >> Network tab - Connection = Settings = '''Use system proxy settings'''
The default setting now is for '''Use system proxy settings''', and that might be causing your problem.
If you select '''''No proxy''''' and restart Firefox your problem should be fixed.

Cannot delete Lists from Reminders app after upgrading to iOS 7. The deal is that those lists don't show in iCloud account in the Web-Browser, so I cannot delete via Browser, when I press the button Edit in the List, there is no Delete button at thebottom

On my iPhone 5, upgraded to iOS 7, the lists in Reminders are impossible to delete. When I press Edit button in the right corner of the app, the button Delete list is supposed to be at the bottom, but it's empty there, the deal is I could delete some of the lists, but most of them I can't. I tried delete iCloud account from iPhone, but they are still there, and still no Delete button. In the Browser I don't see those lists, so cannot delete them from the Browser as well. Could you help me?

Read on another thread here that you now swipe in the opposite direction. Try swiping right to left.

Portal URL: Why cannot access via IP address?

When I try to access portal web with IP address, the tree navigation in browse area always shows blank or keep show "loading...".
But after I access the same URL but change it to domain name address, the tree navigation shows correctly.
Could you please explain what is the setting behind this?
Why in some environment we can access directly from IP address?
Thanks !

Hi Erika
you need to update your host file with your EP server host name and IP address
this host file is present in c:/windows/system32/drivers/etc/hosts
open this host file with notepad
and at the bottom give the values like this
<IP address of your EP Server> <EP Server Host Name>
Note:: you need to provide this settings under EP server host--c:/windows/system32/drivers/etc/hosts
Rgds
Srinivas

Mx880 connected to LAN. Cannot access via wireless. ???

I have an end user on campus who has a Canon MX880 multi-function printer/copier/scanner, etc. I have it configured to a specific IP address, and connected to the college LAN via data cable, data drop. The drop is good, I have tested with a laptop. I manually set the IP4 settings on the MX880, and can ping the printer when connected via ethernet to LAN. As soon as I try to get on the the college wireless LAN, I can't ping it. I took another laptop, disconnected the data cable from the printer, plugged it into the laptop, and manually config'd the laptop to the same manual IP4 settings as the printer is set to. This time, from the other laptop, I can ping connected to the printer port wirelessly or when ethernet connected. So there is nothing wrong with the campus wired or wireless network. It's only when I try and ping the MX880, via the campus wireless network, that I have a problem. Again, I have the MX880 ethernet connected to a data drop. I have the LAN settings enabled, and IP4 manually set. I can ping the printer IP address when ethernet connected from somewhere else on the network, but I can't when I'm using the campus wireless network. And again, If I use two laptops, one used in place of the printer, but set to same IP settings, I have no problem pinging the IP address via LAN or campus wireless. Any ideas???

Most public networks (like the ones on a college campus) have built in firewalls that prevent communication between devices. They're designed primarily to give a device internet access but not to let 2 devices on the network talk to each other for security purposes (so the guy in the dorm next to you can't hack your computer). Trying to use the printer with a public network probably wont work.

Help; I cannot access my browser with all my bookmarks. When I press the firefox icon all that happens is that I go straight to yahoo. My e-mail is asampoh@yahoo.co.uk. Thanks for your help.

When I press the firefox icon on my lap top I go straight to yahoo. There is no firefox browser and all my bookmarks have disappeared. What can I do to get the browser back.
Thanks for your help.
Adrian Asampoh

This can be a problem with the file [http://kb.mozillazine.org/sessionstore.js sessionstore.js] and sessionstore.bak in the [http://kb.mozillazine.org/Profile_folder_-_Firefox Profile Folder]
Delete [http://kb.mozillazine.org/sessionstore.js sessionstore.js] and sessionstore.bak in the [http://kb.mozillazine.org/Profile_folder_-_Firefox Profile Folder]
If you see files sessionstore-##.js with a number in the left part of the name like sessionstore-1.js then delete those as well.
See:
* http://kb.mozillazine.org/Session_Restore
See also:
* http://kb.mozillazine.org/Firefox_crashes
* [[Firefox crashes]]

On Ipod, music files are in Other. Cannot access via Music menu

Ipod Nano 4G
iTunes 8.1.1.10
I sync music files onto ipod from itune.
On itunes they show they got there.
I eject ipod.
And then unable to see songs under Music menu.
iTunes shows me that the Audio files are now Other files.
Using Windows Ic can see that on the ipod music files (F00) are stored in \ipod_control\music\ .
I have tried 5Rs several times and disk mode.
Problem also occurs with podcasts.
Is the unit faulty,

Ipod Nano 4G
iTunes 8.1.1.10
I sync music files onto ipod from itune.
On itunes they show they got there.
I eject ipod.
And then unable to see songs under Music menu.
iTunes shows me that the Audio files are now Other files.
Using Windows Ic can see that on the ipod music files (F00) are stored in \ipod_control\music\ .
I have tried 5Rs several times and disk mode.
Problem also occurs with podcasts.
Is the unit faulty,

My access was blocked because i left my pc on at home and now i cannot access anymore with thunderbird only via browser how can i restore access??

I cannot access anymore via thunderbird while with the same pw i can access via browser after my account was blocked how can i restore access via email program?

I was on my gmail account and looked at settings forward and pop/imap
be sure they are activated.
Imap if you want to access it from several places. That way you have the original on Gmail-server and copies on your pc.
Pop on the other hand loads down the emails. perfect if its just one pc.
(i'm not sure the Gmail-server deletes them thou).

Cannot access browser

Hello there, I am posting this message on behalf of my sister.
She cannot access her browser on the blackberry curve 8520, it comes up saying please contact your network provider. She is connected to wifi and I do not understand why it won't let her access it, so I thought I'd install the browser back to see if it has any effect.
So is there anyway someone could give me a blackberry browser link and a blackberry appworld link aswell because my sisters app world has vanished.
Thanks

Hello rsanto360 and welcome to the BlackBerry Support Community Forums.
If your sister's data plan doesn't include browsing, this error may appear.
Have her go to Options>Advanced Options>Browser and ensure the default Browser is set to Mobile HotSpot. If she does subscribe to a data plan, have her contact her mobile carrier to ensure Browsing is included.
As for the issue with BlackBerry World, she can install it from www.blackbery.com/appworld
Let us know if this helps.
-HMthePirate
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

Cannot access portal thru IP address

Hi,
I noticed that i cannot access my portal thru its IP.
ie: http://<IP address>:50000/irj does not work
but if i use the hostname to which it is mapped,it works..
what is the reason behind this?
Thanks
rocky

Hi.
It is true.
A reason is the SSO cookies mechanism, and it cannot work without a hostname.
about this procedure: http://help.sap.com/saphelp_nw2004s/helpdata/en/28/7c383f717b5f03e10000000a114084/frameset.htm
And similar answered questions:
Re: Portal URL: Why cannot access via IP address?
Facing Issues in accessing Portal through IP
Re: After the login, the portal displays again the login page
regards.
Leandro

Cannot access a work IP address

I am working from a MacBook Pro. I work from home. I cannot access two work websites. I also cannot access my work e-mail. My two work websites have the same IP address. I had AT&T come out after extensive time on the phone with their 2nd tier tech group help me. They eventually replaced my modem. Once the modem was replaced it worked flawlessly until the next day when I tried to access the two websites and also e-mail. I thought it was an AT&T issue so I switched over to Time Warner. Once again with the new modem it worked flawlessly. Next day fail. I cannot ping the IP address and I have also have cleared the Cache, cookies, and history. I am running an OS X Maverick. If I turn on my hotspot on my phone I am able to access the websites and my work e-mail but that would end up being so costly to run this data 8 hours a day on my phone.
When I am working I sit on these 2 websites for 5 to 6 hours a day because I need to access information.

Hi.
It is true.
A reason is the SSO cookies mechanism, and it cannot work without a hostname.
about this procedure: http://help.sap.com/saphelp_nw2004s/helpdata/en/28/7c383f717b5f03e10000000a114084/frameset.htm
And similar answered questions:
Re: Portal URL: Why cannot access via IP address?
Facing Issues in accessing Portal through IP
Re: After the login, the portal displays again the login page
regards.
Leandro

L7600 Cannot Access via browser

Similar Messages

Maybe you are looking for