LabVIEW 2009 and its sp1

I have the LabVIEW 2009 and LABVIEW 2009 SP1. Do I have to install 2009 first and then 2009 SP1? Or the 2009 SP1 also includes the full 2009. The reason I am asking is that I installed my 2009 on a computer, which took forever by the way. After the 2009 installation is completed, I installed the 2009 SP1, and it took pretty much the same amount of them, so I am wondering did I have to install both?
Yik
Kudos and Accepted as Solution are welcome!

Thanks!
Kudos and Accepted as Solution are welcome!

Similar Messages

Run-time engine problem in Labview 2009 and Labview 2010

I have a problem with Labview 2009 and Labview 2010. I updated my Labview 2009 into 2010. But it turned out to be a trial one, because i did not have the serial number. So I uninstalled the Labview 2010. however, the funny stuff came over. I cannot use my Labview 2009. So i uninstalled Labview 2009 again. But eventually, I could not reinstall Labview 2009. Every time i had a runtime error and i could not proceed with the installation. in addition, any installation related to Labview is not permitted and the same error came up every time. it is very annoying.
So, What is the deal?
I attached the error here. Any comments or advice are welcomed and appreciated.
Attachments:
error.docx ‏2305 KB

By chance is this machine's language set to any non-English locale? You would check the locale setting by:
Opening Control Panel.
Opening "Regional and Language Options".
Looking Under "Regional Options" >> "Standards and Formats"
If it is set to something besides English, trying setting it to English and please report back what locale it was set to (or if this even solves the problem).
Regards,
- WesW

LABVIEW 2009 and lvanlys.dll

Hi,
I'm relatively new to LABVIEW and I'm building an application with LABVIEW 2009. The application works well on my PC. However, the application is
intended to be ran on another machine. I then tried two approaches. First, I copied the executable file onto the second machine and second, I created
an installer file. Both methods resulted in an error when the executable was ran on the second machine. Here is the error:
"Missing external function lvanlys.dll Mean_Head.C in VI NI_AALBase.lvlib:Mean.vi". I'm hoping anyone out there knows the solution to this.
Thanks!
Bobby C

I'm not sure that link is appropriate since it talks about LabVIEW 7.1 installer and windows NT.
For LabVIEW 8 or higher, make sure that the data folder is part of the install. Done correctly, there will be your application, the data folder, and in the data folder, lvanlys.dll.

Potential Bug with LabVIEW 2009, Report Generation Toolkit, and MS Office 2003

We have discovered an issue with the above listed software. Specifically this pertains to Print Report.vi in the Report Gen palette. Basically, we have discovered that with Office 2003 installed the VI will error out. We've been using it in an executable, and the executable physically fails (and asks us to report an error to Microsoft). With Office 2007 we don't have a problem. We've tried building the examples into executables, and those work because they are printing HTML reports.
Also, we have converted back to LabVIEW 8.6 and rebuilt the executable and installed and it works perfectly. Its on the combination of LabVIEW 2009 and Office 2003 that seems to fail.

yeah, we had seen that, and been told about it by another user. we tried, to no avail. we still have ended up having to migrate back to 8.6.1 to get the executable to run properly.

VLC and LabView 2009

I am trying to use the latest ActiveX VLC v1.1.4 in LabView, and every time I insert the VLC ActiveX Object, LabView crashes. I've read other posts which noted success by either: 1) using a web browser ActiveX object calling VLC or 2) finding a unique older version of VLC which doesn't cause their particular version of LabView to crash.
I have yet to find a version of VLC which works with LabView 2009, and I'd prefer not to call a web browser ActiveX component just to play a video with VLC.
Has anyone had success integrating a VLC ActiveX object in LabView 2009?
Thanks,
Stephen McClanahan

just try the attached vi. Maybe this is what you are looking for.
attached is 2010 and lv86 version.
If you don't have Wait Until Next ms Multiple__ogtk.vi look in the archive or download openg libraries.
cosmin
Attachments:
vlc.vi ‏13 KB
vlc ver86.zip ‏17 KB

How to activate labview 2009 sp1 after reinstall window?

hi
my camputer was installed labview 2009 and it was activated by the academic license. Currently, i reinstalled the window and i cannot activate the labview 2009. So how can i activate it?

Hi,
In the license manager (Start » National Instruments » License Manager) you should set the correct parameters concerning your license server.
Regards,
Da Helmut

How to run the VI developed in labVIEW 2011 in its previous versions

Hi all,
I am currently using LabVIEW 2011 in my home PC.
But, all my school computers are installed with LabVIEW 2010 and 2010 SP1.
How to run the VI developed in LabVIEW 2011 in its previous versions?
Is there any conveter for that?
Regards
Prasanth T
Solved!
Go to Solution.

Open the VI in LabVIEW 2011 and use the File menu option, Save for Previous Version.

In block diagram connecting wire getting blur while saving the VI in LabVIEW 2009

Hello,
I am using Labview 2009, And while I am saving a simple VI connecting wires are getting blurry. What could be the problem?? Is it affect my program while running?
Solved!
Go to Solution.

Go into Tools>>Options, select the Block Diagram page and find the section called Constant Folding. If the CF for wires check box is checked, then this is most likely the reason. You can uncheck the check box and it won't affect the way your code runs.
If this isn't the case, you should upload an image of what it looks like.
Try to take over the world!

Labview 2009 I/O assistant issue

Hi,
I'm using labview 2009, and I can't get the I/O assistant to work-everytime I try to run it, it gives me the error message "Measurement & Automation Explorer or the Instrument I/O Assistant is not installed correctly. Please install these from LabVIEW Driver CD". I've tried uninstalling and re-installing the I/O assistant, but it's not helping-is there anything else that can cause this error I should be looking for?
Thanks

Hi ciwong,
This problem usually originates from installation order. You want to install the drivers after you install after you install LabVIEW.
Another things that jumps out is that you are listing NI VISA 488.2 as version 2.1. The current version of NI VISA is version 5 and the current version of NI 488.2 is version 2.73.
Please let us know if you have any questions
Joe Daily
National Instruments
Applications Engineer
may the G be with you ....

Build Specifications gone with LabVIEW 2009

I'm using LabVIEW 2009 and I still have the same problem as described in the following post (where all the answers were for older LabVIEW versions):
http://forums.ni.com/t5/LabVIEW/build-specifications-gone/m-p/625815
When I move a LabVIEW project from one PC to another, parts of the build specifications are gone. In the specification for the executable I have to redefine the start-up VI, the included files and the icon.
Is this a known issue and is there a fix for it?

Hello,
this might be a corrupt project file. Does this only happen with this project?
If so, then I'd suggest recreating the project and the build specifications on the original PC and trying to migrate it again to the other PC.
Regards,
Joseph Tagg

Remove labview 2009 without using add/remove program

Hi all,
I have problem with removing LabVIEW 2009.
I have deleted some folders in C drive, NI folder.
Now I can't run my LabVIEW 2009 and it doesn't show up in my add/remove program list.
I tried to delete all folder and files in C drive under NI folder, but error message pop out shows that I do not have the authority to do so.
So, how can I remove it completely ?
I intended to reinstall LabVIEW 2009 after I have removed it completely.
Appreciate your help very much.
Solved!
Go to Solution.

That is why I say try to reinstall LabVIEW. It might just do a repair of your installation. Then you can use add/remove programs to completely uninstall it.
But when you completely uninstall it there will be NI folders remaining. These are things like user.lib.
Have you tried to reinstall the runtime engine?
One last thing. I don't know how you got your install so messed up but remember that if you build an installer you should not install that onto a system with the development environment. There are so many things that can go wrong.
=====================
LabVIEW 2012

Error when trying to set up OPC I/O server with LabView 2009

Hi.I get an error when I try to set up OPC I/O server with LabView 2009 and the DSC module. If I open an empty project, right click ”My Computer”. Select new / I/O Server… and then OPC Client, the following error appears: Unable to browse OPC Server from the selected machine.Error -2147467262 occurred at GetOPCServerList.viPossible reason(s):LabVIEW: (Hex 0x80004002) No such interface supported. I have tried to repair LabView, but with no luck. Any idea what it could be?

The problems are not related to each otherOk then. Lets try getting this solved. Lemme dig......

Quanser DC Motor Control Trainer missing VI's for labview 2009

Hi my name is phillip, a student developer working with labview 2009 and the Quanser DC Motor Control trainer with ELVIS II. I have failed to run the VI for speed control, it appears to be broken and says four sub-vi's are missing and they are "Intergrator.VI," "Integrator (DBL).VI," "Transfer Function.VI," "and "Transfer Function (DBL).VI.". I happen to have installed the control design and simulation toolkit but this has not solved the problem. Please help!!!!

Hi Phillk, I have the exact same problem with the missing VIs for the Quanser DC motor control with the NIELVIS also for Labview 2009.
Can you please tell me where I can find these VIs? Can you send them to me if it is possible?
I would really appreciate it,
I need the Transfer Function.vi, Transfer Function (DBL).vi and the integrators too.
Thank you,
Carlos M. Rodriguez
[email protected]

Upgrade Mathscript LabVIEW 2009

Hello
I have developped an application in LabVIEW 8.6 that
contains a large MathScript node. it's time to upgrade to LabVIEW 2009
and i am facing problems in that. I have the Mathscript RT Module
installed and activated on my computer.
I should emphasize that
the application works perfectly in 8.6. After the first execution in
2009 version, i got 2 run-time errors:
-90031 : "unknown output
variable". The variable is of string type. it's pointed in a red dot
(see picture). I have never seen that red dot before...
another
error in another node: -20104: input parameter have at least one NaN
element. What's a NaN element? this error occurs in a line that looks
like A=median(B) where B is a row vector.
also in this second
node, i have a lot of output variables pointed in red dots, the string
outputs and some of the double precision as well.
What
are the requirements to upgrade to LabVIEW 2009, as far as MathScript
is concerned? are there issues to be considered? major changes i should
be aware of?
Thank you very much
Sam
Solved!
Go to Solution.
Attachments:
error Mathscript.JPG ‏10 KB

Thanks Jattas
i am still confused about the coercion dots but since they don't necessarily indicate problems with the code, i'll keep the focus on something else to begin with. i beleive i should look for solutions for the whole upgrade. What i did not mention in the first post (because not sure if related to Mathscript) is the error messages i have on saving the VI before quitting, i also got those messages while loading the VI.
Attached are 3 messages that appeared (Please see pics). The result is obviously a borken arrow:VI failed to complie, Mathscript node failed to compile.
that would be a nice discussion with NI support but it's hard to explain these things on the phone. i am gathering every information that might be relevent for the migration.
thanks again
Attachments:
error1.JPG ‏12 KB
error2.JPG ‏13 KB
error3.JPG ‏12 KB

Could I connect the design in Multisim in LabVIEW 2009?

Hi,
I had design a generator in LabVIEW 2009, and now I need to send the output of the generator to pass through a transformer and a transmission lines. I found out that I could use Multisim to design the transformer and transmission lines.
I was wondering if anyone knows on how to transfer/connect the transformer and the transmission lines design in Multisim using LabVIEW 2009? In my final presentation, I need to use LabVIEW 2009 and show to my supervisor the result of the simulation.
Ridhwan Ali

Hi Ridhwan,
Here are the options:
1) You can save the results from the generator to a LVM file in LabVIEW. Then, go to Multisim and use the LVM_VOLTAGE (Sources Group, SIGNAL_VOLTAGE_SOURCES Family) source to open the file, connect this source to your circuit.
2) You can create a VI in LabVIEW and use it in Multisim. Here is a good tutorial:
How to Create a LabVIEW Based Virtual Instrument for NI Multisim
3) You can control Multisim from LabVIEW via the Multisim API. Basically you can create a LabVIEW application that opens the Multisim engine, loads a circuit, and executes simulation. Basically you can bring simulation results to LabVIEW for further processing. More info:
An Introduction to Multisim Automation with the LabVIEW Multisim Connectivity Toolkit (beta)
LabVIEW Multisim Connectivity Toolkit
I hope this helps. Good luck with your application!
Fernando D.
National Instruments

LabVIEW 2009 and its sp1

Similar Messages

Maybe you are looking for