Labview 2010 Crash on launch

Hi, I installed Labview 2010sp1 and when I start it gives me this error
"Problem Event Name: APPCRASH
   Application Name: LabVIEW.exe
   Application Version: 10.0.1.4002
   Application Timestamp: 4d2fa7a6
   Fault Module Name: LabVIEW.exe
   Fault Module Version: 10.0.1.4002
   Fault Module Timestamp: 4d2fa7a6
   Exception Code: c0000005
   Exception Offset: 018d7f76
   OS Version: 6.1.7601.2.1.0.256.1
   Locale ID: 1040
   Additional Information 1: 0a9e
   Additional Information 2: 0a9e372d3b4ad19135b953a78882e789
   Additional Information 3: 0a9e
   Additional Information 4: 0a9e372d3b4ad19135b953a78882e789 "
I can not use it and what can I do?

Hello Simx7719,
Thank you for your update about the troubleshooting for the APPCRASH error.
Concerning the second one, did you check you installed the LabVIEW Run Time Engine before deploying your executable? Is there any error message or warnig that points us to any explanation? In what way your application doesn't work? What's the incorrect behavior?
Thank you in advance for your interest.
Have a nice day!
Best regards
Matteo C. - Test Engineer

Similar Messages

Labview 2010 crashes XP while looking for webserver

Hi,
I am using a Windows 7 laptop with LV 2010 to compile my 32-bit executable. I've copied it to my target Windows XP, SP3 computer and after running it for a short while it rebooted the computer automatically (I believe the reboot was caused by a BSOD).
I've gone into the Windows Event Viewer and there is an event that says "Labview information: Error: 404 "Not Found" for "national instruments/ni-rpc/interface/eadfc80d-1e6f-425b-8986-12ccef98f646/ncalrpc", file "c:/program files/national instruments/shared/ni webserver/www/national instruments/ni-rpc/interface/eadfc80d-1e6f-425b-8986-12ccef98f646/ncalrpc": Can't access URL ."
I'm attaching a jpg of the Event in case I typed it incorrectly. There is another post that mentions this error but there is no resolution and the discussion went in a different direction: http://forums.ni.com/t5/LabVIEW/LabVIEW-2010-unstable-on-Windows-7/m-p/1247366/highlight/true
Neither my Win 7 development laptop or my target Win XP system have this www folder.
Has anyone seen this before or know the cause? Thanks.
Steve
Attachments:
Event Viewer small.jpg ‏69 KB

Altenbach,
Thanks for the quick reply.
Yes, the time stamp of this error coincides with the crash. I guess I assumed that it caused the crash because I see about 20-25 instances of it in the Event Viewer. Immediately before these errors appear there are two instances of the NI Configuration Manager with the Description saying "Opening configuration database".
This only happened on time and I have not been able to reproduce it again.
I'll need to explain to my customer why this Error has appeared so many times in the Event Viewer, and also how I can get it to not happen again. Do you have any suggestions? Once I isolate this error and prevent it from happening again then I can monitor the computer for future crashes.
Thanks.
Steve

Labview 2010 crash at startup windows 7

Hi,
Labview crashes on startup. I get this message: "Labview 10.0 Development System has stopped working." I don't get any further than this.
I have 95 computers running Windows 7 64-bit Enterprise. To install Labview on these I use the automated installer with these options: "/q /acceptlicenses yes /r:n /applyspecfile k:\zfdmsi\Labview2010\yellow1\".
This was working on Windows XP. I have tried to install Labview manually on one of the windows 7 computers and it works fine.. But I cant do that on 95 computers...
Any ideas why it's crashing?
Thanks in advance.
Solved!
Go to Solution.

Yes, m: is a network drive. We have a local policy on all workstations redirecting My Documents to the M: drive.
I got the issue resolved by installing Labview 2010 SP1

LabVIEW 2010 crashes when changing representation of TypeDef

Hello NI,
I have to report a bug
which causes LV 2010 to crash with error in "datamgr.cpp", line 2720.
This crash is reproduceable.I use LabVIEw 2010, 32 bit on Windows 7.
To cause this crash you have to perform the
following steps (I attached a sample VI to reproduce these steps.):
Place a ring control on the FP, change
representation to I32
On the BD, create a property node “Strings
And Values[]”
The datatype of this property is Array of
Cluster with 2 Elems, “String” & “Value”, where “Value” is of type I32
Create a control of this property,
surprisingly the type of Value is “extended”
On the FP, select the cluster inside the
array, click “Customize Control…” from Edit- menu
In the Control- Editor change the DataType
of Value to I32, then exit the Control Editor without saving the control,
but replacing the original cluster
LabVIEW 2010 will crash with the error
message stated above
The problem is to change the
representation of the cluster element, where the cluster is part of a typedef. A
solution is to forbid to call the “Customize”- editor directly from the FP (not
nice) or to forbid to replace the orginal control, instead force the user to
save the altered control to a .ctl (nicer).
This shows a general problem with TypeDefs,
where the array of a not-typedefed cluster is typedefed. This was discussed
earlier with the cursor list of waveform graphs (couldn’t find it anymore, but
read it in this forum) where this problem also can occur. So this is an appeal
to National Instruments to change the TypeDef to the clusters and make arrays
of them.
And, after all, for me it is
unexpected behaviour that a constant / control / indicator, created from a
property (or any terminal / node I can find on the BD) has another datatype
than the original terminal or node.
Greets, Dave
Picture 1: Type of property node
Picture 2: Type of created control
Picture 3: Error message
Greets, Dave
Attachments:
Ring TypeDef Problem.vi ‏66 KB

Hi All,
I am also facing the same bug from the long time which causes loss of data unexpected.Please solve this bug and tell me any way to solve this.I am using Control Type Def in my project.
Thanks
Yogeshwar
Attachments:
error.jpg ‏19 KB

LabVIEW 2010 Crash

All,
LabVIEW 2010 now crashes every time I try and open it. It seems to crash at the "loading plugins" phase. I don't recall what I did to cause this. How can I solve this?
Also there's no error log in the LabVIEW data folder under my documents.
Regards,
Ken

Has anything changed about the system? Has the system ever been in a working state? Has the computer received recent updates from IT or the OS? Did you face any installation problems?
Has any third party software been recently installed on the computer?
Thank you very much for your time and follow up. Perhaps an installation repair for LabVIEW would assist in ensuring all the correct files are still on disk, in case anything may have been deleted.
Cheers,
Patrick Corcoran
Application Engineering Specialist | Control
National Instruments

LabVIEW 2010 crash when calling user32.dll

Interesting LabVIEW 2010 "feature" I discovered this morning.
Attached are two identical VIs, one saved in 2010 and one saved in 2009. These VIs were specifically written to demonstrate the bug I stumbled upon this afternoon. Each VI when run should allow you to find a specific program (window) open in Microsoft Windows and bring it to the foreground. It relies on "user32.dll" to perform this operation. It also allows you to specify the calling convention for the function call.
In LV 2009, either calling convention works, without error. However, in LV 2010 the calling convention for the function must be "stdcall (WINAPI)" and not the default "C". If the calling convention is "C" then LabVIEW crashes and closes without warning.
If you happen to have both LV 2009 and LV 2010 on your computer, I would love to hear if this phenomenon is duplicated so that I can pinpoint whether the bug is LV 2010 related or is more specific to my personal setup.
Thanks,
~David
Solved!
Go to Solution.
Attachments:
LV2010 test.vi ‏13 KB
LV2009 test.vi ‏14 KB

221113
Return
CLFN with the wrong calling convention may siliently crash LabVIEW.
LabVIEW 8.5 through 2009 could adjust the calling convention at run time if the user selected the wrong option. In 2010 this no longer happens. More information is found in KnowledgeBase 59KB14WI
Workaround: Use the correct calling convention
Reported Version: 2010 32-bit
Resolved Version: N/A
Added: 07/23/2010
From 2010 release notes.
Paul Falkenstein
Coleman Technologies Inc.
CLA, CPI, AIA-Vision
Labview 4.0- 2013, RT, Vision, FPGA

LabVIEW 2010 crashes often when deleting multiple diagram objects

LabVIEW 2010f2 has been reasonably stable for me so far, but I seem to get crashes to the desktop exactly under the following conditions:
When deleting larger sections of code (=several objects selected with the mouse, typically including bad wires in the selection, followed by hitting the delete key).
When this happens, LabVIEW becomes unresponsive for about 10 seconds, then crashes to the desktop. This scenario is quite reproducible in a statistically significant way. While it is not 100% reproducible, I've had it happen a couple of times in a row on the same restored VI, doing basically the same delete procedure. It happened in quite a few unrelated VIs.
This is LabVIEW 2010f2 32bit on Windows 7 64bit. There is nothing in the failure log.
I wonder if anybody else has seen similar correlations.... Thanks!
LabVIEW Champion . Do more with less code and in less time .
Solved!
Go to Solution.

Ben J wrote:
I'll be looking forward to a jing or reproducable code of the issue.
OK, got one!
Open the attached file in 2010f2. (from this discussion. All that padding and re-stripping of the 2D array is not necessary, so we try to clean up the code a bit. )
Jing file is here.
We delete a few things in the right, then on the left, then on the bottom left.
At 7 seconds, LabVIEW becomes unresponsive. At 12 seconds, it crashes to the desktop.
(I was able to record this two times in a row!)
LabVIEW Champion . Do more with less code and in less time .
Attachments:
BlurBenchmark3.vi ‏211 KB

LabVIEW 2010 in-placeness crash bug

[cross-posted to LAVA]
I found an odd LabVIEW 2010 bug that will cause a hard crash. The bug appears to be related to how LabVIEW operates on data in-place and some interaction between clusters, arrays, and the Aum Array Elements node. It's hard to describe verbally, so I'll just draw you a picture
LabVIEW 2010 CRASH.vi (16.56K)

No crash on my system: LV2010, W7 64-bit, Pentium E5200
a.lia-user-name-link[href="/t5/user/viewprofilepage/user-id/88938"] {color: black;} a.lia-user-name-link[href="/t5/user/viewprofilepage/user-id/88938"]:after {content: '';} .jrd-sig {height: 80px; overflow: visible;} .jrd-sig-deploy {float:left; opacity:0.2;} .jrd-sig-img {float:right; opacity:0.2;} .jrd-sig-img:hover {opacity:0.8;} .jrd-sig-deploy:hover {opacity:0.8;}

Error 404 causes Labview 2010 to crash but only occasionally

Hello,
I am requesting help to solve a problem with LabVIEW 2010 crashing. I am new to this company and the last Labview developer left without providing
background on this problem. Labview crashes after running project VIs. Labview closes without warning or error messages. The project acquires data from pressure transducers, dP transducers, thermocouples, IEPE, load cells, and voltages through NI real-time system and has digital I/O. NI hardware includes PXI-1050 with modules 6221, 6280, 6224, 6220 and NI PXI-1052, SCXI-1306, SCXI-1112, SCXI-1520, and SCXI-1102. I've reviewed the labview program and the software relies heavily on shared variables, references, and local variables but I cannot find anything that stands out as a problem in the software .
The program crashed again today after running for only 1/2 hour and was not recording data. No error message occurred before the crash and the only error after restarting LabVIEW was the standard message that LabVIEW did not close properly. I went to the Event Viewer and at the time of the crash I received the following information:
Event ID = 3299
Source = LabVIEW
Log = Application
Level = Error
LabVIEW Information: Error 404 "Not found" for "/national instruments/ real-time execution trace toolkit/ 2.0/ trace receiveport", file "Crogram files (x86)/ national instruments /shared/ ni webserver/ www/ national instruments/ real-time execution trace toolkit/ 2.0/ trace receiveport": Can't access URL
According to Event Viewer, this error 3299 occurred 15 times in the last 3 days. LabVIEW crashed today at 10:19 am at the same time this error 3299 occurred but LabVIEW did not crash the other times this error occurred in the last 3 days. I believe this error is related to the crash but does not usually cause the crash. It appears to me from reading the error message that the error is the result of occasional lose of communication with the real-time system (Can't find URL). Any suggestions how to resolve this would be greatly appreciated.
Bill

1. Have you had this code working before on this or another machine?
2. Which operating system and version of LabVIEW are you running? (This can be found in Control Panel >> All Control Panel Items >> System)
3. Which National Instruments Drivers are you using? (This can be found in the measurement an automation explorer under the software tab [a screenshot would be good])
I would look into removing afsetup.exe which is a data collection tool provided by Microsoft which could a) not be installed correctly and/or b) trying to pull data from LabVIEW. I think this may help you out, as even though your programs aren't explicitly calling it, the service is running in the background.
Secondly, I would look into stopping the NI Web Server application that could be polling a web page that's not needed.

Application crashes in Windows 7 64bit made in Labview 2010 sp1 f2 with Fault module name%3A lvrt.dll%2C version 10.0.0.4033 and exception code c0000005

I build an application exe and then its installer along with run time environment.
The installers instals the application correctly but when I try to execute the application, I get an error that application has crashed and Windows must close it down or search for solutions online with this additional information for the crash.
Problem signature:
Problem Event Name: APPCRASH
Application Name: AGMS.exe
Application Version: 1.3.0.0
Application Timestamp: 4c24e8f5
Fault Module Name: lvrt.dll
Fault Module Version: 10.0.0.4033
Fault Module Timestamp: 4c9273f4
Exception Code: c0000005
Exception Offset: 00005310
OS Version: 6.1.7601.2.1.0.256.1
Locale ID: 1033
Additional Information 1: 0a9e
Additional Information 2: 0a9e372d3b4ad19135b953a78882e789
Additional Information 3: 0a9e
Additional Information 4: 0a9e372d3b4ad19135b953a78882e789
Read our privacy statement online:
http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0409
If the online privacy statement is not available, please read our privacy statement offline:
C:\Windows\system32\en-US\erofflps.txt
I am using labview 2010 sp1 32 bit on a 64-bit machine, with the following specs
Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.130318-1533)
Language: English (Regional Setting: English)
System Manufacturer: Dell Inc.
System Model: Dell System XPS L502X
BIOS: Default System BIOS
Processor: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz (8 CPUs), ~2.0GHz
Memory: 8192MB RAM
Available OS Memory: 8106MB RAM
Page File: 3457MB used, 12753MB available
Windows Dir: C:\Windows
DirectX Version: DirectX 11
DX Setup Parameters: Not found
User DPI Setting: Using System DPI
System DPI Setting: 96 DPI (100 percent)
DWM DPI Scaling: Disabled
DxDiag Version: 6.01.7601.17514 32bit Unicode
The exe /application runs fine on my PC but when I try to run it on another PC it crashes. The other PC has similar specs as given below
Operating System: Windows 7 Ultimate 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.140303-2144)
Language: English (Regional Setting: English)
System Manufacturer: LENOVO
System Model: HuronRiver Platform
BIOS: Default System BIOS
Processor: Intel(R) Core(TM) i3-2330M CPU @ 2.20GHz (4 CPUs), ~2.2GHz
Memory: 4096MB RAM
Available OS Memory: 4010MB RAM
Page File: 1359MB used, 6658MB available
Windows Dir: C:\Windows
DirectX Version: DirectX 11
DX Setup Parameters: Not found
User DPI Setting: Using System DPI
System DPI Setting: 96 DPI (100 percent)
DWM DPI Scaling: Disabled
DxDiag Version: 6.01.7601.17514 32bit Unicode
I tried another machine, 64 bit of course, as I want to deploy my application on a 64bit PC, but still got the same problem.
This other machine was from HP, iCore 3 (4 CPUs) 2.2GHz, 4GB RAM and running Windows Professional 64 bit.
Now as I see it, it could be a Run-time environment mis-match error.
For this I tried installing a 64 bit LVRTE from NI, but still no sucess.
I checked DEP, for all 3 PCs and it was set to the following
Turn on DEP for essential Windows programs and services only (first option).
I am confused. I can not find a solution for this and it is really frustrating.

But I am assuming that when I make the installer, the 32-bit Run Time Engine is appened with the installer, as show below
Since from the picture you can see its including the support installers from '\Program Files (x86)\'
The application runs queries to fetch data from database in SQL server 2008, and for that I am using a Microsoft SQL Native Client 2008 R2 64 bit ( this is the only version that installs on either PC, even the one on which I developed my LV Application).
I am not using any driver, only toolkits for reports - and for that I un-checked the "Remove unused polymorphic VI instances" when making the executable, otherwise LV throws up an exception that share variable are not being included.
Yes I did reboot every time after I ran the installation.
Still getting the same error.

LabVIEW 2010 F2 - Crash - Localization issue ?

Hi fellows !
I am using LabVIEW 2010 F2 (French localized version) and I am facing this strange behavior. Can you confirm that this is a bug and / or this is because I am using a localized version of LabVIEW ?
When using the Modifications:VI property node (CTRL+SHIFT+B) and connecting its output to a case structure everything works fine (it looks like that).
But now if I change the Modifications:VI property to Modifications:Front Panel and let the output of the property node connected to the case structure, LabVIEW crashes or the broken arrow appears.
If I click on the broken arrow or try to save the VI (CTRL+S), I get the following error message :
Fpsane.cpp line 442
Thanks for your help.
Regards,
Da Helmut
Attachments:
err.PNG ‏11 KB
test.png ‏14 KB
test.vi ‏7 KB

Hi,
Thanks for the answer.
There is another bug with LabVIEW 2010 (F4 this time).
To reproduce it you have to create a (strict) type definition that consists of a cluster and put a constant which is linked to this typedef on the BD (just select the .ctl file in the BD) and then delete the type definition from the hard drive.
Close the VI that has the constant in the BD.
Re-open the VI, and in the BD, right click on the cluster constant and select "View as Icon". Now you get LabVIEW crashed. (ok it is useless doing that on a non existing typedef but this is crashing LabVIEW, so I thought this should be reported).
Keep me informed if you have any further informations about that.
Regards,
Da Helmut

Deleting broken wires crashes Labview 2010

Hi
I am down to earth after
enjoying all the nice features of LV 2010.
I randomly encounter
hour-glass hang-up when I try to delete broken wires. This is really
unpredictable as far as I have watched. I t happens if click on a broken with
the mouse or when I select a couple of those. It does not happen, if I use
ctrl-b.
When you try to delete it,
the hour glass comes up and the window is no longer refreshed.
I use the task-manger to
kill LV after
that a wild hard disk action starts, whoever initiates that ??
After LV-restart I usually
can recover a lot, but this make RAEL work almost impossible.
I a running an English LV
2010f2 on a German WinXP professional.
And Please, please patch
this as soon as possible.
Gabi
7.1 -- 2013
CLA

Hi Gabi,
I'm glad to hear that you are enjoying LabVIEW 2010! Can i ask what is the specifiation of the computer you are using it on?
This is because it might be that your computer doesn't have enough memory for this program.
Also there is a patch for LabVIEW 2010, in this link.
Hope this helps!
John McLaughlin
Insides Sales Engineer Team Leader
National Instruments UK & Ireland

Labview 2010 randomly restarts computer - windows event viewer points to nap agent

When running my current VI that I am working on, the computer will ranomly reboot. There is no freeze, or blue screen, just a reboot. When examining the windows event viewer after the reboot, the following warning is listed immediately preceding the reboot:
Event ID 39
The Network Access Protection Agent was unable to determine which HRAs to request a health certificate from.
A network change or if GP is configured, a configuration change will prompt further attempts to acquire a health certificate. Otherwise no further attempts will be made.
Contact the HRA administrator for more information.
Previous to getting this warning before a reboot, I was getting the following error:
Event ID 10016
The application-specific permission settings do not grant Local Launch permission for the COM Server application with CLSID
{24FF4FDC-1D9F-4195-8C79-0DA39248FF48}
to the user NT AUTHORITY\SYSTEM SID (S-1-5-18). This security permission can be modified using the Component Services administrative tool.
This is a DCOM service eror and the CLSID is referring to NAPAGENT. So I configured DCOM to allow the NAPAGENT to start and now I get the Event ID 39 warning and still get the reboot.
I am not sure why labview is even asking for DCOM or NAPAGENT to start at all. My VI is simply reading information from two serial instruments.
This reboot behavior does not occur when the computer is not running labview.
I am attaching a copy of the main VI, if it will be helpful I can post the sub VI's as well.
Thanks in advance for your help.
-Justin Lee
Attachments:
testscan10.8.vi ‏179 KB

Hi Joe,
Thanks for the reply.
I am running windows XP pro service pack 3.
I am running a standard instal of labview 2010 with the latest VISA drivers, no other modules or options installed.
I am only reading and writing to the serial ports (com) in my code. I don't believe that virus/spyware/malware is to blame for several reasons.
1. This only occurs when running this VI in labview.
2. I have replicated this problem on another computer.
3. I am behind a government (DOE) firewall and virus scans and checks are performed constantly.
4. If I take out the serial portion of my code via a T/F case structure, it will not crash.
The code will run fine for sevetral hours sometimes and then crash, other times it will crash after only a few minutes.
Please let me know what other information you require.
Thanks!
Justin Lee

Ouvrir un projet LabVIEW 2010 avec 2011

Bonjour,
Je travaille sur un projet qui a été développé sous LabVIEW 2010 et je viens de passer à version 2011. Cepedant il ne m'est plus possible d'ouvrir de nombreux fichiers avec la version 2011. Il s'agit notamment de fichiers projet (.lvproj), classe (.lvclass) et quelques VIs. Lorsque j'essaie de les ouvrir LabVIEW crashe et m'affiche le message suivant :
J'espère que vous pourrez m'aider à identifier la cause de cette erreur...

Hi,
Thanks for posting on NI forum.
This forum is a worldwide forum, you have to write your questions in english.
This type of error seems to be a double read of your project, did you close the project in LV2010 before open it in 2011?
When you run your project, LabVIEW loads files or shows you the error immediatly??
What is the size of the project?
Could you try too recompile your project without launching it. When you lauch LV, click on " Option >> Avancée >> Recompiler... " and chose the project directory (You must have all files of your project in this directory).
Best regards,
Nicolas M.
National Instruments France
#adMrkt{text-align: center;font-size:11px; font-weight: bold;} #adMrkt a {text-decoration: none;} #adMrkt a:hover{font-size: 9px;} #adMrkt a span{display: none;} #adMrkt a:hover span{display: block;}
Journées Techniques LabVIEW 2012 : du 27 septembre au 22 novembre
2 sessions en parallèle : Débuter a...

Exe compiled in LV 2010 crash - Since installing LV 2012 SP1 and 2013

Exe compiled in LV 2010 crash - Since installing LV 2012 SP1 and 2013
Double-click on exe icons (LV apps written in 2010), the application icon appears on taskbar then disappears (program crashes).
I have tried re-installing the exe's but doesn't fix. Is there an issue with the new LV RTE's?
Any suggestions for fix???

battler,
Have you tried making your exe into a debuggable exe? You can do this through your project build specification Advanced>>Enable Debugging. Make sure you check the box for Wait for Debugger. This means when you launch your exe you can connect to it from LabVIEW and see your block diagrams, use highlight execution, probles etc. It is quite possible that you are running into an error case while your program is loading and it is exiting.
Regards,
Jeff Peacock
Product Support Engineer | LabVIEW R&D | National Instruments

Labview 2010 Crash on launch

Similar Messages

Maybe you are looking for