LabVIEW 2010 Crash
All,
LabVIEW 2010 now crashes every time I try and open it. It seems to crash at the "loading plugins" phase. I don't recall what I did to cause this. How can I solve this?
Also there's no error log in the LabVIEW data folder under my documents.
Regards,
Ken
Has anything changed about the system? Has the system ever been in a working state? Has the computer received recent updates from IT or the OS? Did you face any installation problems?
Has any third party software been recently installed on the computer?
Thank you very much for your time and follow up. Perhaps an installation repair for LabVIEW would assist in ensuring all the correct files are still on disk, in case anything may have been deleted.
Cheers,
Patrick Corcoran
Application Engineering Specialist | Control
National Instruments
Similar Messages
-
Labview 2010 crashes XP while looking for webserver
Hi,
I am using a Windows 7 laptop with LV 2010 to compile my 32-bit executable. I've copied it to my target Windows XP, SP3 computer and after running it for a short while it rebooted the computer automatically (I believe the reboot was caused by a BSOD).
I've gone into the Windows Event Viewer and there is an event that says "Labview information: Error: 404 "Not Found" for "national instruments/ni-rpc/interface/eadfc80d-1e6f-425b-8986-12ccef98f646/ncalrpc", file "c:/program files/national instruments/shared/ni webserver/www/national instruments/ni-rpc/interface/eadfc80d-1e6f-425b-8986-12ccef98f646/ncalrpc": Can't access URL ."
I'm attaching a jpg of the Event in case I typed it incorrectly. There is another post that mentions this error but there is no resolution and the discussion went in a different direction: http://forums.ni.com/t5/LabVIEW/LabVIEW-2010-unstable-on-Windows-7/m-p/1247366/highlight/true
Neither my Win 7 development laptop or my target Win XP system have this www folder.
Has anyone seen this before or know the cause? Thanks.
Steve
Attachments:
Event Viewer small.jpg 69 KBAltenbach,
Thanks for the quick reply.
Yes, the time stamp of this error coincides with the crash. I guess I assumed that it caused the crash because I see about 20-25 instances of it in the Event Viewer. Immediately before these errors appear there are two instances of the NI Configuration Manager with the Description saying "Opening configuration database".
This only happened on time and I have not been able to reproduce it again.
I'll need to explain to my customer why this Error has appeared so many times in the Event Viewer, and also how I can get it to not happen again. Do you have any suggestions? Once I isolate this error and prevent it from happening again then I can monitor the computer for future crashes.
Thanks.
Steve -
Labview 2010 crash at startup windows 7
Hi,
Labview crashes on startup. I get this message: "Labview 10.0 Development System has stopped working." I don't get any further than this.
I have 95 computers running Windows 7 64-bit Enterprise. To install Labview on these I use the automated installer with these options: "/q /acceptlicenses yes /r:n /applyspecfile k:\zfdmsi\Labview2010\yellow1\".
This was working on Windows XP. I have tried to install Labview manually on one of the windows 7 computers and it works fine.. But I cant do that on 95 computers...
Any ideas why it's crashing?
Thanks in advance.
Solved!
Go to Solution.Yes, m: is a network drive. We have a local policy on all workstations redirecting My Documents to the M: drive.
I got the issue resolved by installing Labview 2010 SP1 -
LabVIEW 2010 crashes when changing representation of TypeDef
Hello NI,
I have to report a bug
which causes LV 2010 to crash with error in "datamgr.cpp", line 2720.
This crash is reproduceable.I use LabVIEw 2010, 32 bit on Windows 7.
To cause this crash you have to perform the
following steps (I attached a sample VI to reproduce these steps.):
Place a ring control on the FP, change
representation to I32
On the BD, create a property node “Strings
And Values[]”
The datatype of this property is Array of
Cluster with 2 Elems, “String” & “Value”, where “Value” is of type I32
Create a control of this property,
surprisingly the type of Value is “extended”
On the FP, select the cluster inside the
array, click “Customize Control…” from Edit- menu
In the Control- Editor change the DataType
of Value to I32, then exit the Control Editor without saving the control,
but replacing the original cluster
LabVIEW 2010 will crash with the error
message stated above
The problem is to change the
representation of the cluster element, where the cluster is part of a typedef. A
solution is to forbid to call the “Customize”- editor directly from the FP (not
nice) or to forbid to replace the orginal control, instead force the user to
save the altered control to a .ctl (nicer).
This shows a general problem with TypeDefs,
where the array of a not-typedefed cluster is typedefed. This was discussed
earlier with the cursor list of waveform graphs (couldn’t find it anymore, but
read it in this forum) where this problem also can occur. So this is an appeal
to National Instruments to change the TypeDef to the clusters and make arrays
of them.
And, after all, for me it is
unexpected behaviour that a constant / control / indicator, created from a
property (or any terminal / node I can find on the BD) has another datatype
than the original terminal or node.
Greets, Dave
Picture 1: Type of property node
Picture 2: Type of created control
Picture 3: Error message
Greets, Dave
Attachments:
Ring TypeDef Problem.vi 66 KBHi All,
I am also facing the same bug from the long time which causes loss of data unexpected.Please solve this bug and tell me any way to solve this.I am using Control Type Def in my project.
Thanks
Yogeshwar
Attachments:
error.jpg 19 KB -
LabVIEW 2010 crash when calling user32.dll
Interesting LabVIEW 2010 "feature" I discovered this morning.
Attached are two identical VIs, one saved in 2010 and one saved in 2009. These VIs were specifically written to demonstrate the bug I stumbled upon this afternoon. Each VI when run should allow you to find a specific program (window) open in Microsoft Windows and bring it to the foreground. It relies on "user32.dll" to perform this operation. It also allows you to specify the calling convention for the function call.
In LV 2009, either calling convention works, without error. However, in LV 2010 the calling convention for the function must be "stdcall (WINAPI)" and not the default "C". If the calling convention is "C" then LabVIEW crashes and closes without warning.
If you happen to have both LV 2009 and LV 2010 on your computer, I would love to hear if this phenomenon is duplicated so that I can pinpoint whether the bug is LV 2010 related or is more specific to my personal setup.
Thanks,
~David
Solved!
Go to Solution.
Attachments:
LV2010 test.vi 13 KB
LV2009 test.vi 14 KB221113
Return
CLFN with the wrong calling convention may siliently crash LabVIEW.
LabVIEW 8.5 through 2009 could adjust the calling convention at run time if the user selected the wrong option. In 2010 this no longer happens. More information is found in KnowledgeBase 59KB14WI
Workaround: Use the correct calling convention
Reported Version: 2010 32-bit
Resolved Version: N/A
Added: 07/23/2010
From 2010 release notes.
Paul Falkenstein
Coleman Technologies Inc.
CLA, CPI, AIA-Vision
Labview 4.0- 2013, RT, Vision, FPGA -
LabVIEW 2010 crashes often when deleting multiple diagram objects
LabVIEW 2010f2 has been reasonably stable for me so far, but I seem to get crashes to the desktop exactly under the following conditions:
When deleting larger sections of code (=several objects selected with the mouse, typically including bad wires in the selection, followed by hitting the delete key).
When this happens, LabVIEW becomes unresponsive for about 10 seconds, then crashes to the desktop. This scenario is quite reproducible in a statistically significant way. While it is not 100% reproducible, I've had it happen a couple of times in a row on the same restored VI, doing basically the same delete procedure. It happened in quite a few unrelated VIs.
This is LabVIEW 2010f2 32bit on Windows 7 64bit. There is nothing in the failure log.
I wonder if anybody else has seen similar correlations.... Thanks!
LabVIEW Champion . Do more with less code and in less time .
Solved!
Go to Solution.Ben J wrote:
I'll be looking forward to a jing or reproducable code of the issue.
OK, got one!
Open the attached file in 2010f2. (from this discussion. All that padding and re-stripping of the 2D array is not necessary, so we try to clean up the code a bit. )
Jing file is here.
We delete a few things in the right, then on the left, then on the bottom left.
At 7 seconds, LabVIEW becomes unresponsive. At 12 seconds, it crashes to the desktop.
(I was able to record this two times in a row!)
LabVIEW Champion . Do more with less code and in less time .
Attachments:
BlurBenchmark3.vi 211 KB -
Hi, I installed Labview 2010sp1 and when I start it gives me this error
"Problem Event Name: APPCRASH
Application Name: LabVIEW.exe
Application Version: 10.0.1.4002
Application Timestamp: 4d2fa7a6
Fault Module Name: LabVIEW.exe
Fault Module Version: 10.0.1.4002
Fault Module Timestamp: 4d2fa7a6
Exception Code: c0000005
Exception Offset: 018d7f76
OS Version: 6.1.7601.2.1.0.256.1
Locale ID: 1040
Additional Information 1: 0a9e
Additional Information 2: 0a9e372d3b4ad19135b953a78882e789
Additional Information 3: 0a9e
Additional Information 4: 0a9e372d3b4ad19135b953a78882e789 "
I can not use it and what can I do?Hello Simx7719,
Thank you for your update about the troubleshooting for the APPCRASH error.
Concerning the second one, did you check you installed the LabVIEW Run Time Engine before deploying your executable? Is there any error message or warnig that points us to any explanation? In what way your application doesn't work? What's the incorrect behavior?
Thank you in advance for your interest.
Have a nice day!
Best regards
Matteo C. - Test Engineer -
LabVIEW 2010 in-placeness crash bug
[cross-posted to LAVA]
I found an odd LabVIEW 2010 bug that will cause a hard crash. The bug appears to be related to how LabVIEW operates on data in-place and some interaction between clusters, arrays, and the Aum Array Elements node. It's hard to describe verbally, so I'll just draw you a picture
LabVIEW 2010 CRASH.vi (16.56K)No crash on my system: LV2010, W7 64-bit, Pentium E5200
a.lia-user-name-link[href="/t5/user/viewprofilepage/user-id/88938"] {color: black;} a.lia-user-name-link[href="/t5/user/viewprofilepage/user-id/88938"]:after {content: '';} .jrd-sig {height: 80px; overflow: visible;} .jrd-sig-deploy {float:left; opacity:0.2;} .jrd-sig-img {float:right; opacity:0.2;} .jrd-sig-img:hover {opacity:0.8;} .jrd-sig-deploy:hover {opacity:0.8;} -
Error 404 causes Labview 2010 to crash but only occasionally
Hello,
I am requesting help to solve a problem with LabVIEW 2010 crashing. I am new to this company and the last Labview developer left without providing
background on this problem. Labview crashes after running project VIs. Labview closes without warning or error messages. The project acquires data from pressure transducers, dP transducers, thermocouples, IEPE, load cells, and voltages through NI real-time system and has digital I/O. NI hardware includes PXI-1050 with modules 6221, 6280, 6224, 6220 and NI PXI-1052, SCXI-1306, SCXI-1112, SCXI-1520, and SCXI-1102. I've reviewed the labview program and the software relies heavily on shared variables, references, and local variables but I cannot find anything that stands out as a problem in the software .
The program crashed again today after running for only 1/2 hour and was not recording data. No error message occurred before the crash and the only error after restarting LabVIEW was the standard message that LabVIEW did not close properly. I went to the Event Viewer and at the time of the crash I received the following information:
Event ID = 3299
Source = LabVIEW
Log = Application
Level = Error
LabVIEW Information: Error 404 "Not found" for "/national instruments/ real-time execution trace toolkit/ 2.0/ trace receiveport", file "Crogram files (x86)/ national instruments /shared/ ni webserver/ www/ national instruments/ real-time execution trace toolkit/ 2.0/ trace receiveport": Can't access URL
According to Event Viewer, this error 3299 occurred 15 times in the last 3 days. LabVIEW crashed today at 10:19 am at the same time this error 3299 occurred but LabVIEW did not crash the other times this error occurred in the last 3 days. I believe this error is related to the crash but does not usually cause the crash. It appears to me from reading the error message that the error is the result of occasional lose of communication with the real-time system (Can't find URL). Any suggestions how to resolve this would be greatly appreciated.
Bill1. Have you had this code working before on this or another machine?
2. Which operating system and version of LabVIEW are you running? (This can be found in Control Panel >> All Control Panel Items >> System)
3. Which National Instruments Drivers are you using? (This can be found in the measurement an automation explorer under the software tab [a screenshot would be good])
I would look into removing afsetup.exe which is a data collection tool provided by Microsoft which could a) not be installed correctly and/or b) trying to pull data from LabVIEW. I think this may help you out, as even though your programs aren't explicitly calling it, the service is running in the background.
Secondly, I would look into stopping the NI Web Server application that could be polling a web page that's not needed. -
I build an application exe and then its installer along with run time environment.
The installers instals the application correctly but when I try to execute the application, I get an error that application has crashed and Windows must close it down or search for solutions online with this additional information for the crash.
Problem signature:
Problem Event Name: APPCRASH
Application Name: AGMS.exe
Application Version: 1.3.0.0
Application Timestamp: 4c24e8f5
Fault Module Name: lvrt.dll
Fault Module Version: 10.0.0.4033
Fault Module Timestamp: 4c9273f4
Exception Code: c0000005
Exception Offset: 00005310
OS Version: 6.1.7601.2.1.0.256.1
Locale ID: 1033
Additional Information 1: 0a9e
Additional Information 2: 0a9e372d3b4ad19135b953a78882e789
Additional Information 3: 0a9e
Additional Information 4: 0a9e372d3b4ad19135b953a78882e789
Read our privacy statement online:
http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0409
If the online privacy statement is not available, please read our privacy statement offline:
C:\Windows\system32\en-US\erofflps.txt
I am using labview 2010 sp1 32 bit on a 64-bit machine, with the following specs
Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.130318-1533)
Language: English (Regional Setting: English)
System Manufacturer: Dell Inc.
System Model: Dell System XPS L502X
BIOS: Default System BIOS
Processor: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz (8 CPUs), ~2.0GHz
Memory: 8192MB RAM
Available OS Memory: 8106MB RAM
Page File: 3457MB used, 12753MB available
Windows Dir: C:\Windows
DirectX Version: DirectX 11
DX Setup Parameters: Not found
User DPI Setting: Using System DPI
System DPI Setting: 96 DPI (100 percent)
DWM DPI Scaling: Disabled
DxDiag Version: 6.01.7601.17514 32bit Unicode
The exe /application runs fine on my PC but when I try to run it on another PC it crashes. The other PC has similar specs as given below
Operating System: Windows 7 Ultimate 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.140303-2144)
Language: English (Regional Setting: English)
System Manufacturer: LENOVO
System Model: HuronRiver Platform
BIOS: Default System BIOS
Processor: Intel(R) Core(TM) i3-2330M CPU @ 2.20GHz (4 CPUs), ~2.2GHz
Memory: 4096MB RAM
Available OS Memory: 4010MB RAM
Page File: 1359MB used, 6658MB available
Windows Dir: C:\Windows
DirectX Version: DirectX 11
DX Setup Parameters: Not found
User DPI Setting: Using System DPI
System DPI Setting: 96 DPI (100 percent)
DWM DPI Scaling: Disabled
DxDiag Version: 6.01.7601.17514 32bit Unicode
I tried another machine, 64 bit of course, as I want to deploy my application on a 64bit PC, but still got the same problem.
This other machine was from HP, iCore 3 (4 CPUs) 2.2GHz, 4GB RAM and running Windows Professional 64 bit.
Now as I see it, it could be a Run-time environment mis-match error.
For this I tried installing a 64 bit LVRTE from NI, but still no sucess.
I checked DEP, for all 3 PCs and it was set to the following
Turn on DEP for essential Windows programs and services only (first option).
I am confused. I can not find a solution for this and it is really frustrating.But I am assuming that when I make the installer, the 32-bit Run Time Engine is appened with the installer, as show below
Since from the picture you can see its including the support installers from '\Program Files (x86)\'
The application runs queries to fetch data from database in SQL server 2008, and for that I am using a Microsoft SQL Native Client 2008 R2 64 bit ( this is the only version that installs on either PC, even the one on which I developed my LV Application).
I am not using any driver, only toolkits for reports - and for that I un-checked the "Remove unused polymorphic VI instances" when making the executable, otherwise LV throws up an exception that share variable are not being included.
Yes I did reboot every time after I ran the installation.
Still getting the same error. -
LabVIEW 2010 F2 - Crash - Localization issue ?
Hi fellows !
I am using LabVIEW 2010 F2 (French localized version) and I am facing this strange behavior. Can you confirm that this is a bug and / or this is because I am using a localized version of LabVIEW ?
When using the Modifications:VI property node (CTRL+SHIFT+B) and connecting its output to a case structure everything works fine (it looks like that).
But now if I change the Modifications:VI property to Modifications:Front Panel and let the output of the property node connected to the case structure, LabVIEW crashes or the broken arrow appears.
If I click on the broken arrow or try to save the VI (CTRL+S), I get the following error message :
Fpsane.cpp line 442
Thanks for your help.
Regards,
Da Helmut
Attachments:
err.PNG 11 KB
test.png 14 KB
test.vi 7 KBHi,
Thanks for the answer.
There is another bug with LabVIEW 2010 (F4 this time).
To reproduce it you have to create a (strict) type definition that consists of a cluster and put a constant which is linked to this typedef on the BD (just select the .ctl file in the BD) and then delete the type definition from the hard drive.
Close the VI that has the constant in the BD.
Re-open the VI, and in the BD, right click on the cluster constant and select "View as Icon". Now you get LabVIEW crashed. (ok it is useless doing that on a non existing typedef but this is crashing LabVIEW, so I thought this should be reported).
Keep me informed if you have any further informations about that.
Regards,
Da Helmut -
Deleting broken wires crashes Labview 2010
Hi
I am down to earth after
enjoying all the nice features of LV 2010.
I randomly encounter
hour-glass hang-up when I try to delete broken wires. This is really
unpredictable as far as I have watched. I t happens if click on a broken with
the mouse or when I select a couple of those. It does not happen, if I use
ctrl-b.
When you try to delete it,
the hour glass comes up and the window is no longer refreshed.
I use the task-manger to
kill LV after
that a wild hard disk action starts, whoever initiates that ??
After LV-restart I usually
can recover a lot, but this make RAEL work almost impossible.
I a running an English LV
2010f2 on a German WinXP professional.
And Please, please patch
this as soon as possible.
Gabi
7.1 -- 2013
CLAHi Gabi,
I'm glad to hear that you are enjoying LabVIEW 2010! Can i ask what is the specifiation of the computer you are using it on?
This is because it might be that your computer doesn't have enough memory for this program.
Also there is a patch for LabVIEW 2010, in this link.
Hope this helps!
John McLaughlin
Insides Sales Engineer Team Leader
National Instruments UK & Ireland -
LabVIEW 2009 crashes at startup with the presence of a certain CRT version on the system
When installing our LabVIEW integration package on a system running
LabVIEW 2009 LabVIEW will crash at startup afterwards. Using 'dependency
walker' reveals, that 'nicont.dll' causes this crash because of a
side-by-side configuration problem. After some debugging I found out
that on this particular system installing a certain version of the
Microsoft CRT will stop LabVIEW from functioning. My fix now is to
recompile our code with a newer version of VS. I now ship a VS9 version
of the runtime and everything is working as expected.
However
I guess the real problem lies within the LabVIEW installer. I guess a
needed version of the CRT is not installed by LabVIEW. It still works
because due to some policy files on the machine it gots defaulted to a
compatible version at startup. However when I install the following 2
merge modules on the target system LabVIEW does no longer work:
Microsoft_VC80_CRT_x86.msm (file version inside: 8.0.50727.762)
policy_8_0_Microsoft_VC80_CRT_x86.msm (file version inside: 8.0.50727.4053)
Renaming
the *.policy file in the SxS dir on the target system gets LabVIEW back
to run, but of course other SW needing this file does not run then
I was using XP, 32 bit SP 3
I can provide additional information if needed. Is this a known problem? Is there a fixed version of LabVIEW already?
Message Edited by anotherStefan on 02-05-2010 05:44 AMSure! I tried to attach the installer causing the problem to this message.
However I failed miserably(BAD GATEWAY from the upstream server). Where can I upload the installer to or what do I need to do?
It will install some other stuff as well (A bunch of VIs, a DLL and an
OCX(this needs the CRT I have trouble with)and the CRT and MFC runtimes I
mentioned. An updated version of the installer can be obtain here(however it does no longer show the issue):
http://www.matrix-vision.com/functions/count.php?url=products/hardware/family/SC/mvBlueFOX/LabVIEW_a...
The only difference between the two packages is, that the OCX in the
attached file has been build using VS2005SP1 and in the package the link
points to I did use VS2008. Apart from that I changed the 2 merge
modules from Microsoft (CRT and MFC) -
3D graphs cause LabVIEW 2010 to hang
I've been using LabVIEW 2010 for several weeks without any problems, but today I noticed that it doesn't work at all with anything related to the 3D picture control. Today was the first time that I tried doing anything with the 3D picture tool since installing LV 2010. Dropping any of the 3D Graphs on the front panel of a new VI causes LV2010 to hang. (By hang, I mean the VI window remains open but most UI things no longer work. Right-clicking on the window does not show a context menu. The main menu doesn't work. The X button does not close the VI front panel window nor the diagram window. Control-Q does not cause LabVIEW to quit. I have to kill the process in Task Manager.) It is the same story with just a plaing 3D picture indicator. Also, the solarsystem.vi example does not work either. The problems start as soon as I open the solarsystem.vi. After killing LV with Task Manager and relaunching LV10, I do not get the LV message about a previous crash.
The problem I am talking about is for LabVIEW 2010 with the f2 patch running in Win7. I am actually running it using VMware Fusion 3.1.3 on a 2009 Mac Pro running Lion. The Mac drivers are all updated. Since it is VMware Fusion machine, the video driver on the Windows side is part of the VMware Tools installation, which is up to date.
After searching the forums, I've tried all the other potential solutions I could find: 1) repaired LV2010 using add/remove programs and 2) tried using the compatibilty mode settings to turn off Aero.
Interestingly, 3D graphs work fine on the Mac side for LV2010 for Mac.
Even more insterestingly, 3D graphs work fine on Win7 for LV 8.5, which I still have installed. The fact that it works fine for LV 8.5 would seem to indicate that Lion did not introduce the problem and that the video driver is working fine.
Solved!
Go to Solution.Yep, it's the same virtual machine. I set it up almost 2 years ago and it has been extremely stable. Both LabVIEW 8.5 and 2010 have been perfectly happy on it. It's a great way to do LabVIEW on Win7. I didn't notice any changes at all to the VM when I upgraded from Snow Leopard to Lion. I installed LabVIEW 2010 before upgrading to Lion, but I didn't have occasion to work with 3D controls before the upgrade to Lion so I don't know if it would have worked on Snow Leopard. The Mac versions of both LabVIEW 8.5 and LabVIEW 2010 also work great on the both Snow Leopard and Lion.
I happen to have an XP virtual machine too, but I haven't installed LabVIEW there. Let me know if that would be a worthwhile test.
You might check with Marc Page--unless he has already upgraded again I think he has a similar machine to mine.
The video card is the original stock:
NVIDIA GeForce GT 120:
Chipset Model: NVIDIA GeForce GT 120
Type: GPU
Bus: PCIe
Slot: Slot-1
PCIe Lane Width: x16
VRAM (Total): 512 MB
Vendor: NVIDIA (0x10de)
Device ID: 0x0640
Revision ID: 0x00a1
ROM Revision: 3386
Displays:
Cinema HD Display:
Resolution: 2560 x 1600
Pixel Depth: 32-Bit Color (ARGB8888)
Main Display: Yes
Mirror: Off
Online: Yes
Rotation: Supported
Display Connector:
Status: No Display Connected -
Strange problem of calling library function node in labview 2010 and 2011
one year ago,I develop a program to usb device data and it works well,in labview 8.6 or 2009(win xp).Recently, When I test
the program in labview 2010 and labview 2011(win xp).,the program always crash immediately.I check the program and find main
problem is in call library function node. In my program,I use labview 2009 library for the USBExpress driver for
Silicon Labs USB MCU's from:https://decibel.ni.com/content/docs/DOC-9522,for example, 2 functions SI_OPEN and SI_READ
can not work well.
the header definition of SI_OPEN and SI_READ is:
SI_STATUS WINAPI SI_Open(
DWORD dwDevice,
HANDLE* cyHandle
SI_STATUS WINAPI SI_Read(
HANDLE cyHandle,
LPVOID lpBuffer,
DWORD dwBytesToRead,
LPDWORD lpdwBytesReturned,
OVERLAPPED* o = NULL
the SI_STATUS is equivalent to int type.
orignally, for HANDLE * in SI_Open, the parameter type in call library function node is numeric, data format is unsigned 32 bit integer ,and pass pointer to value.
for HANDLE in SI_Read, the parameter type in call library function node is numeric, data format is unsigned 32 bit integer ,and pass value.The program works well in labview 8.6&2009,however,crash in labview 2010 &2011.
later,I debug the program, for HANDLE *, I choose parameter type in call library function node as adapt to type, data format is point to Handles.for HANDLE, I choose parameter type in call library function node as adapt to type, data format is Handles by Value.Crash not happend in labview 2010&2011,however,it cannot read any data from from USB device correctly as before.I can not find the reason.
Dear friends,I need your help to answer the problem. Thank you.Based on the help page it looks like it should execute asynchronously.
The thing in the description that leads me to believe they execute asynchronously is that you can configure the library to run as a multi-threaded operation.
Please take a look here to see the difference between synchronous and asynchronous execution.
Since the code even has the ability to be multi-threaded, you can consider it as running in parallel to your other code.
Any data returned is passed to the thread that called that function.
Cory K
Maybe you are looking for
-
Help: iphone 4 does not sync with Outlook 2007 ANYMORE
It used to, but not anymore :-( I have an iphone 4 and work with Microsoft Outlook 2007. In the beginning all worked perfect and I could sync my calendar from outlook with my iphone. Then one day it stopped working and I don't know why or what has ha
-
Hi, Does PGI creates any accounting document? Also I would like to know that PGI means that the delivery is complete and the goods are issued to the customer.Please suggest if my concept of PGI is correct?
-
I have the old CK-7W kit without the charging lead. I see the CA-116 is available, but would it charge my 7020 handset? Alternatively, is there another lead which would fit both the 7020 & CK-7W? Solved! Go to Solution.
-
CM40 dispatch planned order among different work centers
Hi we have a finish material ,which can be manufactured using 3 different work centers.Then I create 3 production versions to link each work center . PV1 Routing 1(work center1) BOM 1 production line:work center1 PV2 Routing 1(work center
-
Satellite A305-S6825 - YouTube viewing full screen
Does the following have to be done everytime we turn on the Toshiba notebook (VistaPremium) and go into YouTube? "Try adjusting this Flash Player setting. While the video is playing, right-click on it and click Settings. Uncheck the box for Enable ha