LabVIEW 2010 SP1 may not cleanly shut down

Occasionally LabVIEW 2010 SP1 (32-bit, running on Windows 7) will appear to "hang" when the "Getting Started" window is closed. The window disappears but the shortcut icon still appears in the Windows toolbar in the bottom of the screen. Right-clicking and selecting "Close Program" does not work and Windows seems to think any VIs that have been recently closed are still open. The program is still in the list in Task Manager and it can successfully be shut down all the way from there.
This is more of an annoyance than an operational issue (I think) - is there something I am doing (or failing to do) that causes this problem?
Thanks in advance.

Hello Unplugnow,
Deleting the .ini file will not cause any issues in terms of being able to reload Labview it will simply restore the default settings for Labview which will insure that there were be no data corruption issues. I have tried this procedure on my side with no issue although I would recommend copying the .ini file to another directory in case you need to recover this information at a later time.
To another note, does this issue arise when you are opening a particular VI, or does it occur when you are simply opening and closing Labview?
Best,
Blayne Kettlewell

Similar Messages

Failover cluster not cleanly shutting down service

I've got a two node 2008 R2 failover cluster. I have a single service being managed by it that I configured just as a generic service. The failover works perfectly when the service is stopped, or when one of the machines goes down, and the immediate
failback I have configured works perfectly in both scenarios as well.
However, there's an issue when I take the networking down on the preferred owner of the service. As far as I can tell (this is the first time I've tried failover clustering, so I'm learning), when I take the networking down, the cluster service shuts
down, and in turn shuts down the service I've told it to manage. At this point, when the services aren't running, the service fails over to the secondary as intended. The problem shows up when I turn the networking back on. The service tries
and fails to start on the primary (as many times as I've configured it to try), and then eventually gives up and goes back to the secondary.
The reason for this, examining logs for the service, is that the required port is already in use. I checked some more, and sure enough, when I take the networking offline the service gets shut down, but the executable is still running. This is
repeatable every time. When I just stop the service, though, the executables go away. So it's something to do specifically with how the managed service gets shut down *when it's shut down due to the cluster service stopping*. For some reason
it's not cleaning up that associated executable.
Any ideas as to why this is happening and how to fix/work around it would be extremely welcome. Thank you!

Try to generate cluster log using closter log /g /copy:<path to a local folder>. You might need to bump up log verbosity using cluster /prop ClusterLogLevel=5 (you can check current level using cluster /prop).
You also can look at the SCM diagnostic channel in the event viewer. Start eventvwr. Wait for the clock icon on the Application and Services Logs to go away. Once the clock icon is gone select this entry and in the menu check Show Analytic and Debug Logs.
Now expand to the SCM provider located at
Application and Services Logs\Microsoft\Service Control Manager Performance Diagnostic Provider\Diagnostic.
or Microsoft-Windows-Services/Diagnostic
Enable the log, run repro, disable the log. After that you should see events from the SCM showing you your service state transitions.
The terminate parameters do not seems to be configurable. I can think of two ways fixing the issue
- Writing your own cluster resource DLL where you can implement your own policies. THis would be a place to start http://blogs.msdn.com/b/clustering/archive/2010/08/24/10053405.aspx.
- This option is assuming you cannot change the source code of the service to kill orphaned child processes on startup so you have to clenup using some other means. Create another service and make your service dependent on this new service. This new serice
must be much faster in responding do the SCM commands. On start of this service you using PSAPI enumirate all processes running on the machine and kill the orphaned child processes. You probably should be able to acheve something similar using GenScript resource
+ VB script that does the cleanup.
Regards, Vladimir Petter, Microsoft Corporation

Can not Open exe file that is created by Labview 2010 SP1

Hi Everyone,
My Operating system is XP .. I installed .net latest version but I can not open exe file. I try to open exe file, then crashes , quits without seeing any interface.
I tried with another computer whose o.s is xp too. I can open exe file. I saw it is created by Labview 2010 Sp1
I dont know what the difference is. I attached config file.
Attachments:
TPS65175 C (Vcom only).ini ‏1 KB

burak35 wrote:
[..]Do I need any other components besides .Net?
That's a question only the provider of the application can answer.
You could also take a look into the system event log if there is an indication for the reason of the application failing to start properly. It is possible that certain services are required for the application, but they do not run on the machine.
Another point is possibly missing rights. So you might want to test the application once with the option "Run as Admin" (right click menu item on the application shortcut or the exe itself).
Norbert
CEO: What exactly is stopping us from doing this?
Expert: Geometry
Marketing Manager: Just ignore it.

Application crashes in Windows 7 64bit made in Labview 2010 sp1 f2 with Fault module name%3A lvrt.dll%2C version 10.0.0.4033 and exception code c0000005

I build an application exe and then its installer along with run time environment.
The installers instals the application correctly but when I try to execute the application, I get an error that application has crashed and Windows must close it down or search for solutions online with this additional information for the crash.
Problem signature:
Problem Event Name: APPCRASH
Application Name: AGMS.exe
Application Version: 1.3.0.0
Application Timestamp: 4c24e8f5
Fault Module Name: lvrt.dll
Fault Module Version: 10.0.0.4033
Fault Module Timestamp: 4c9273f4
Exception Code: c0000005
Exception Offset: 00005310
OS Version: 6.1.7601.2.1.0.256.1
Locale ID: 1033
Additional Information 1: 0a9e
Additional Information 2: 0a9e372d3b4ad19135b953a78882e789
Additional Information 3: 0a9e
Additional Information 4: 0a9e372d3b4ad19135b953a78882e789
Read our privacy statement online:
http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0409
If the online privacy statement is not available, please read our privacy statement offline:
C:\Windows\system32\en-US\erofflps.txt
I am using labview 2010 sp1 32 bit on a 64-bit machine, with the following specs
Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.130318-1533)
Language: English (Regional Setting: English)
System Manufacturer: Dell Inc.
System Model: Dell System XPS L502X
BIOS: Default System BIOS
Processor: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz (8 CPUs), ~2.0GHz
Memory: 8192MB RAM
Available OS Memory: 8106MB RAM
Page File: 3457MB used, 12753MB available
Windows Dir: C:\Windows
DirectX Version: DirectX 11
DX Setup Parameters: Not found
User DPI Setting: Using System DPI
System DPI Setting: 96 DPI (100 percent)
DWM DPI Scaling: Disabled
DxDiag Version: 6.01.7601.17514 32bit Unicode
The exe /application runs fine on my PC but when I try to run it on another PC it crashes. The other PC has similar specs as given below
Operating System: Windows 7 Ultimate 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.140303-2144)
Language: English (Regional Setting: English)
System Manufacturer: LENOVO
System Model: HuronRiver Platform
BIOS: Default System BIOS
Processor: Intel(R) Core(TM) i3-2330M CPU @ 2.20GHz (4 CPUs), ~2.2GHz
Memory: 4096MB RAM
Available OS Memory: 4010MB RAM
Page File: 1359MB used, 6658MB available
Windows Dir: C:\Windows
DirectX Version: DirectX 11
DX Setup Parameters: Not found
User DPI Setting: Using System DPI
System DPI Setting: 96 DPI (100 percent)
DWM DPI Scaling: Disabled
DxDiag Version: 6.01.7601.17514 32bit Unicode
I tried another machine, 64 bit of course, as I want to deploy my application on a 64bit PC, but still got the same problem.
This other machine was from HP, iCore 3 (4 CPUs) 2.2GHz, 4GB RAM and running Windows Professional 64 bit.
Now as I see it, it could be a Run-time environment mis-match error.
For this I tried installing a 64 bit LVRTE from NI, but still no sucess.
I checked DEP, for all 3 PCs and it was set to the following
Turn on DEP for essential Windows programs and services only (first option).
I am confused. I can not find a solution for this and it is really frustrating.

But I am assuming that when I make the installer, the 32-bit Run Time Engine is appened with the installer, as show below
Since from the picture you can see its including the support installers from '\Program Files (x86)\'
The application runs queries to fetch data from database in SQL server 2008, and for that I am using a Microsoft SQL Native Client 2008 R2 64 bit ( this is the only version that installs on either PC, even the one on which I developed my LV Application).
I am not using any driver, only toolkits for reports - and for that I un-checked the "Remove unused polymorphic VI instances" when making the executable, otherwise LV throws up an exception that share variable are not being included.
Yes I did reboot every time after I ran the installation.
Still getting the same error.

The system has rebooted without cleanly shutting down first. How to clear this error. Occurs frequently.

Log Name: System
Source: Microsoft-Windows-Kernel-Power
Date: 31-12-2014 14:35:18
Event ID: 41
Task Category: (63)
Level: Critical
Keywords: (2)
User: SYSTEM
Computer: BLISS-ORACLE
Description:
The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-Kernel-Power" Guid="{331C3B3A-2005-44C2-AC5E-77220C37D6B4}" />
<EventID>41</EventID>
<Version>2</Version>
<Level>1</Level>
<Task>63</Task>
<Opcode>0</Opcode>
<Keywords>0x8000000000000002</Keywords>
<TimeCreated SystemTime="2014-12-31T09:05:18.479605300Z" />
<EventRecordID>9113</EventRecordID>
<Correlation />
<Execution ProcessID="4" ThreadID="8" />
<Channel>System</Channel>
<Computer>BLISS-ORACLE</Computer>
<Security UserID="S-1-5-18" />
</System>
<EventData>
<Data Name="BugcheckCode">0</Data>
<Data Name="BugcheckParameter1">0x0</Data>
<Data Name="BugcheckParameter2">0x0</Data>
<Data Name="BugcheckParameter3">0x0</Data>
<Data Name="BugcheckParameter4">0x0</Data>
<Data Name="SleepInProgress">false</Data>
<Data Name="PowerButtonTimestamp">0</Data>
</EventData>
</Event>

Hi,
I agree with Mr X. This should be a BSOD issue. Did you refer to Mr X’s suggestions and solve this issue?
Just addition, troubleshoot this kind of kernel crash issue, we need to analyze the crash dump file to narrow down the root cause of the issue. Please refer to following articles
and check if can help you.
Crash dump analysis using the Windows debuggers (WinDbg)
How to read the small memory dump file that is created by Windows if a crash occurs
By the way, it may be not effective for us to debug the crash dump file here in the forum. If this issues is a state of emergency for you. Please contact Microsoft Customer
Service and Support (CSS) via telephone so that a dedicated Support Professional can assist with your request.
To obtain the phone numbers for specific technology request, please refer to the web site listed below:
http://support.microsoft.com/default.aspx?scid=fh;EN-US;OfferProPhone#faq607
Hope this helps.
Best regards,
Justin Gu
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Building App Gives Error 6 about 50 - 80 - 99% of the time. Windows7, LabVIEW 2010 SP1

Hi
First off here is a link to a discussion of the problem. http://forums.ni.com/t5/LabVIEW/Error-6-occurred-when-building-an-Executable-in-Labview-2009/m-p/997...
I have tried all the suggestions on this link with no luck.
Background: have been using LabVIEW 2010 without problems since Sept, then I started getting the error 6 with the following message.
" Error 6 occurred at Delete in AB_Engine_Delete_Internal_Files.vi->AB_EXE.lvclass:Build.vi
->AB_Engine_Build.vi->AB_Build_Invoke.vi->AB_Build_Invoke.vi.ProxyCaller "
This started on one project and is now occurring on another project. Sometimes it builds 50% of the time, other times I can't get it to build at all. I have upgraded to SP1, no change.
Here are some things I have tried.
Moved build directory to c:\a
Renamed project, moved project right under c:\
Disabled Google , disabled Win indexing, disabled Win7 user acct. Control, run LabVIEW as Admit all the time, win explorer closed
mass compiling, closing the project, closing LabVIEW, re-booting
Unistalled LabVIEW 2010 SP1 and re-install, twice.
I believe I rebuilt my project in a new project.
I moved my projects to a WinXP system laptop I have, and they never get Error 6 ! Short term fix, but I have to use Win7. So I hope this means it is not my code.
The funny thing is that this is totally random. The unfunny thing is having to explain to a client I can't get my code to compile during a frustrating 95% of the time failure episode, yikes!
Any help and suggestions would be welcome.
BTW, the next step is to totally uninstall LabVIEW with a 'special' procedure and piece of code sent to me. Don't want to, but am really at wits end. Also waiting to hear back from my service ticket, but am desperate to have parallel solutions to try.
Thanks
Mark Ramsdale

Thanks for the clarify.
I also meant to post this link. It has a lot of info, this is the link I tried most if not all of the suggestions for.
http://forums.ni.com/t5/LabVIEW/Get-Error-6-about-50-of-time-when-building-Application/td-p/1242634
By the way, I was told that uninstalling LabVIEW will not resolve the issue, dodged a time killer :-)
It seems the error is caused by Win7 and file reserving. Waiting to hear back on that. Have an SR.
Again, any suggestions welcomed, maybe some Win7 ideas from those who know more about it.
mr
Mark Ramsdale

LabVIEW 2010 SP1: "Controls" pop-up palette "Select a control..." bug?

I'm using LabVIEW 2010 SP1 (32-bit) and I noticed today that I cannot place my custom controls on a VI's front panel when I use the "Select a Control..." option on the "Controls" pop-up palette. I'm wondering if anyone else is having this same problem?
Steps to reproduce the problem:
1) Create a custom control, or download/save the attached custom control "Machine State.ctl" (< a strictly-typed enum control).
2) Open a VI (new or existing).
2.1) If the "Controls" palette is visible (pinned open), close it.
3) Right-click with the mouse on the VI's front panel window to display the "Controls" pop-up palette.
Note: DO NOT use the "Controls" option in the "View" menu here.
Note: DO NOT pin open the Controls pop-up palette at this point.
See my comments below in the "Notes" section.
4) "Controls" palette > "Select a Control..." option
5) Using the "Select the Control to Open" dialog, browse to, select and open the custom control file (e.g., "Machine State.ctl").
At this point the on-screen cursor should show the outline of an instance of the custom control I just opened, but for me that doesn't happen; all I see is the "+" crosshair cursor, and left-clicking with the mouse on the front panel does not place an instance of the custom control on the front panel.
Notes:
* In step 3) above, if I open the VI's "View" menu and select the "Controls" option, or if I pop-up the "Controls" palette and pin the palette to keep it open, I can successfully use the "Select a Control..." option to browse to, select, open, and place an instance of my custom control on the VI's front panel. The failure only occurs when I use the "Select a Control..." option on the pop-up (unpinned) version of the Controls palette.
* I can successfully drag-and-drop an instance of a custom control onto a VI's front panel from a Windows Explorer window, or from the LabVIEW project explorer window.
* The host computer is running Windows 7 Enterprise x64 w/ SP1.
Jim
Attachments:
MachineState.ctl ‏5 KB

Just now I tried creating and using controls on five different computers, each running Windows 7 Enterprise x64 w/ SP1.
On three of the systems the problem did not occur; I was able to place a user-defined control on the front panel using the "Select a control..." option on the controls palette.
On two of the systems the problem still occurs. Upon further investigation, however, I learned that the hard drives in these two systems were cloned from a "master" hard drive image the IT department created. So I'm guessing there's some bad mojo on the master hard drive image, and that's what's caused this problem to show up on these two systems (and others).
So for now, I'm just going to put up with having to use the old "drag-and-drop" method for placing user-defined controls on the VIs. Thanks for your feedback and assistance with this.
Jim

Kernel-Power Event ID 41: The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly.

Hello, Currently we are seeing this issue with a couple of our Lenovo T420s laptops with a Solid State Drive. ruffly about 10 or so. The Reboots happen randomly and do not create a dump file. We have contacted Lenovo and they are
not sure why its happening. Since this Crash I set it for Minidump this did not work my next steps will be to Disable Automatic restart on System Failure to see if it brings anything up. I am also looking at using Procmon to dump to a file as well.
If anyone has any other ideas please let me know.
The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly.
+ System
- Provider
   [ Name] Microsoft-Windows-Kernel-Power
   [ Guid] {331C3B3A-2005-44C2-AC5E-77220C37D6B4}
   EventID 41
   Version 2
   Level 1
   Task 63
   Opcode 0
   Keywords 0x8000000000000002
- TimeCreated
   [ SystemTime] 2012-02-01T00:02:48.677610900Z
   EventRecordID 8270
   Correlation
- Execution
   [ ProcessID] 4
   [ ThreadID] 8
   Channel System
   Computer LR8K6TLC.cntr.thrivent.corp
- Security
   [ UserID] S-1-5-18
- EventData
BugcheckCode 0
BugcheckParameter1 0x0
BugcheckParameter2 0x0
BugcheckParameter3 0x0
BugcheckParameter4 0x0
SleepInProgress false
PowerButtonTimestamp 129725280988099400
Event 89, Kernel-Power
ACPI thermal zone ACPI\ThermalZone\THM0 has been enumerated.
_PSV = 0K
_TC1 = 0
_TC2 = 0
_TSP = 0ms
_AC0 = 0K
_AC1 = 0K
_AC2 = 0K
_AC3 = 0K
_AC4 = 0K
_AC5 = 0K
_AC6 = 0K
_AC7 = 0K
_AC8 = 0K
_AC9 = 0K
_CRT = 371K
_HOT = 0K
_PSL - see event data.
---- Details
+
System
Provider
[ Name]
Microsoft-Windows-Kernel-Power
[ Guid]
{331C3B3A-2005-44C2-AC5E-77220C37D6B4}
EventID
89
Version
0
Level
4
Task
86
Opcode
0
Keywords
0x8000000000000020
TimeCreated
[ SystemTime]
2012-02-01T00:02:49.270411900Z
EventRecordID
8271
Correlation
Execution
[ ProcessID]
4
[ ThreadID]
68
Channel
System
Computer
LR8K6TLC.cntr.thrivent.corp
Security
[ UserID]
S-1-5-18
EventData
ThermalZoneDeviceInstanceLength
21
ThermalZoneDeviceInstance
ACPI\ThermalZone\THM0
AffinityCount
1
_PSV
0
_TC1
0
_TC2
0
_TSP
0
_AC0
0
_AC1
0
_AC2
0
_AC3
0
_AC4
0
_AC5
0
_AC6
0
_AC7
0
_AC8
0
_AC9
0
_CRT
371
_HOT
0
_PSL
0000000000000000
Thank you.

We have tested and checked both the Bios and firmware of the SSD Drive's
Bios was up to date and no issue
Firmware was also up to date as well.
Users are still experiencing random Reboots.   I tried to capture the issue with Procmon but since the PC shutdown (Goes to a black screen no power at all even when turning the "Automatically
restart" off under Startup and Recovery) No dmp files as of yet. Unable to configure Procdump due to not knowing where the issue is and what is causing it to happen.
Going to replace one of the PC's with a New one with different hardware to see if this resolve the issue. If anyone has any idea's to be able to capture what maybe happening that would
be great.
Thank you.

Some times my mac not getting shut down, some times my mac not getting shut down

some times my mac not getting shut down, some times my mac not getting shut down
it will show white scree for long time and will not shut down

Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, press the key combination shift-command-U. The application is in the folder that opens.
☞ If you’re running Mac OS X 10.7 or later, open LaunchPad. Click Utilities, then Console in the page that opens.
Step 1
Select "system.log" from the file list. Enter "BOOT_TIME" (without the quotes) in the search box. Note the times of the log messages referring to boot times. Now clear the search box and scroll back in the log to the time of the most recent boot when you had the problem. Post the messages logged during the time when you had the problem – the text, please, not a screenshot. For example, if the problem is a slow startup taking three minutes, post the messages timestamped within three minutes after the boot time. If the problem is a crash or a shutdown hang, post the messages from before the boot time, when the system was about to crash or was failing to shut down.
Edit out excessive repeats and personal information, if any.
If the log doesn't go back far enough in time, scroll down in the Console file list to /private/var/log/system.log.0.bz2. Search the archived log, and if necessary the older ones below them, for the same information.
Step 2
Do the same with kernel.log.
Step 3
Still in Console, look under System Diagnostic Reports for crash or panic logs, and post the most recent one, if any. For privacy’s sake, I suggest you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if present (it may not be.) Please do not post shutdownStall or hang logs – they're very long and not helpful.

Error of LabView 2010 sp1 installed on win7 64bit

I installed LabView 2010 sp1 in a brandnew machine with 64bit Windows7.
During the process of initialize LabView, an error message coms out.
Could anyone help to solve this problem?
Thank you so much!
Attachments:
Error.png ‏45 KB

That appears to be a problem with your .NET installation, not LabVIEW. I'd suggest repairing or reinstalling your .NET framework.

Labview 2010 SP1 silent install

Hello,
I have a student version of Labview 2010 SP1. I have located an article on how to perform a silent install using v2008 (http://digital.ni.com/public.nsf/allkb/AA2371E815A418DD86257169005F2D99?OpenDocument). I was wondering if anyone had a 'spec file' or silent install file for 2010 SP1? If not has anyone tried creating a .MSI using WinInstall?
We are trying to push it out using Group policy to one of our small teaching labs. I was going to create a startup batch to accomplish this.
Thank you
ZoeTaite

OK...after some reading I see you can generate a 'spec file' that will help with the silent installation of the Labview 2010 SP1 software via group policy. Is there a way to to modify the nisuite.xml to automatically register the software? Like I mentioned we are pusing this out to a student lab and I don't want to provide the SN (even though it comes up when you launch it).
ZT

Three way switch compaitable with labview 2010 SP1

Hi,
I am in need of three way switch which is compaitable with labview 2010 SP1.
Plz help me ..
thanks
mahadev

can u help me to upconvert the vi to LV2010. which manual are u talking abt?
Attachments:
3 position.llb ‏46 KB
3switch.ctl ‏8 KB
3switch.vi ‏16 KB

My iTunes will not stay shut down. It automatically restarts even without an iPod plugged in. How do I fix this??

My iTunes, which is the latest version, will not stay shut down. No matter how many times I exit the software, it automatically starts back up. And NO, there are NO iPods plugged in. It's very annoying and is slowing down our desktop immensly. I've tried to find a setting to change it but I'm not a computer/iTunes expert. Can anyone help??

try holding the home button and off button at the same time for about 10 seconds, it should restart

Labview 2010 SP1 - How to install just the labVIEW and remote panel

Hi all
I am currently using a licensed version of LabVIEW 2010 SP1. It came up with 6 to 7 DVD’s each of them containing around 5 GB of data. Installing all these stuffs eats up around 30 GB of ma C drive.
My project just deals with 2 EPOS controllers controlling 2 of maxon EC motors and these 2 EPOS controllers are communicating via USB port with the client PC. This client PC have to be monitored and controlled remotely by host PC containing the same LabVIEW version.
To do this, do I have to install all of these 7 DVD’s or just enough to download the “LabVIEW for education 2010 SP1” from the NI website, available in the below link “http://search.ni.com/nisearch/app/main/p/ap/tech/lang/en/pg/1/sn/n8:28,ssnavdl/”
Awaiting for your reply friends.
Thanks in advance

Duplicate Post

MacBook Pro (OS X 10.9.1) calendar continues to "connect to server" and will not allow shut down or restart. Force quit worked. How can I make this calendar "behave"?

MacBook Pro (OS X 10.9.1) calendar continues to "connect to server" and will not allow shut down or restart. Force quit worked. How can I make this calendar usable? The problem began after I updated to Maverick.

babowa, it seems like it is using Fuse & NTFS, so I don't think it's the classic WD + 10.9 mess, but extra WD tools & drivers can still break things MtTran.
MrTran, if you must use unsupported disk formats on your Mac you must also consider actually paying the developers that made the trial software.
It's probably a good idea to follow the developers removal instructions, reboot & then install one tool at a time.
MacFuse, FuseOSX, NTFS-3G are all likley to confict if you run older versions so you need to be sure you are using the latest version. I can't remeber which one depends on the other, so you will need to read the manuals.
When the disk is readable copy the data to another disk. You could probably do this from a Linux distro or Windows if OS X won't do it.
If you insist on only using the trial versions you will need to reinstall Mac OS, copy data off this disk & reformat it.
Is there any good reason for not using the Mac HFS extended format?

LabVIEW 2010 SP1 may not cleanly shut down

Similar Messages

Maybe you are looking for