LabVIEW 2011 to 2010

Hi all,
Need help to convert VIs attached below (LabVIEW 2011) to LabVIEW 2010.
Thank you very much
Solved!
Go to Solution.
Attachments:
Arduino mod for apc220-43.zip ‏4908 KB

Here you go.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines
Attachments:
NET Basic Serial Write and Read (1).vi ‏17 KB

Similar Messages

Downconversion from LabVIEW 2011 to 2010

Please help convert to 2011 project to 2010. Thanks!
Attachments:
TestSolution.zip ‏320 KB

The link at the top of the LabVIEW board is for the Version Conversion That is where you need to post your request.

Trying to install Student Edition of Labview 2011, but instead got 2010

I'm installing the Student Edition of Labview 2011 on a laptop and finally when finished it turns out to be the Student edition Labview 2010, Service Pack 1 version 10.0.1. The receipt clearly say LabVIEW 2011 Student Edition Software - Suite - Download. Did I miss a step or something while installing?

Nevermind... Needed more sleep. For some reason when it created the icon it selected the 2010 verson not the 2011 verson.

Error -1074397038 occurred at IMAQ Start.vi for 64bit Labview 2011 SP1, Win7

Hello,
I am using a MC1362 camera from Mikrotron with a PCIe1433 framegrabber. I was using it with windows XP, 32 bit, labview 2010 SP1 32 bit, it was working perfectly fine. I just switch to windows 7 with labview 2011 SP1 64bit, and it is not working anymore with my custom routine in labview, though it works with MAX and camera file generator and I use the same camera file.
When I run my routine, I have this error message:
Error -1074397038 occurred at IMAQ Start.vi
Possible reason(s):
NI-IMAQ: The requested serial termination string was not found in the returned buffer.
Then, If I try to run the camera with MAX, it doesn't work anymore, I have to reboot the camera, and put it in the right mode with the Mikrotron control tool to obtain an image.
I have seen similar issue on a Basler camera on the forum, and it has been solved by using a camera file to set the different parameters. There is no camera file complete to set all the parameters of the camera, so I had to program them in serial to drive the camera with my Labview routine.
Could you help me to solve this issue please?
Thanks
Bests
David Dulin

This forum post is already handled --> SR 1154262.
Kind regards,
Corné Westeneng
Applications Engineer
NI-Netherlands

Application crashes when calling DLL built with LabVIEW 2011

Hello everybody,
Our application calls DLLs built with LabVIEW 2010 SP1. We installed LabVIEW 2011 and built some DLLs. So far so good. If we start our application and run 2010 DLLs it still works fine. If we run a 2011 DLL just once no error happens, but if we try to run the same 2011 DLL our application crashes reporting the error below. I saved the code for 2010 version and built a DLL and it works fine. Does anyone know why?
Thank you in advance.
#Date: Fr, 16. Sep 2011 16:25:25
#OSName: Microsoft Windows XP Service Pack 3
#OSVers: 5.1
#OSBuild: 2600
#AppName: PasTA
#Version: 11.0f2 32-bit
#AppKind: AppLib
#LabVIEW Base Address: 0x30000000
16.09.2011 16:25:26.181
Crash 0x0: Crash caught by NIER
File Unknown(0) : Crash: Crash caught by NIER
minidump id: 8a779b3f-51d7-4864-8e4d-6ab0195cd158
ExceptionCode: 0xC0000005
N
0x3072C804 - lvrt <unknown> + 0
0x3072CBB8 - lvrt <unknown> + 0
0x7C864191 - KERNEL32 <unknown> + 0
0x7C83AB50 - KERNEL32 <unknown> + 0
0x00000000 - PasTA <unknown> + 0
Attachments:
error.PNG ‏11 KB

On that note, you should be able to create DLLs in 2010 and run them with 2011, correct?? In my case, I have a 2010 built DLL (talking to sbRIO), most of the functions work when run in 2011, but a couple of them lock up LabVIEW on the desktop (but not the sbRIO), no lock ups happen with 2010 on the desktop.

Labview 2011 save for previous version crashes

Hello,
I am trying to save an existing Labview 2011 project to any previous version. I have tried 2010 all the way down to 8.0. I have a clean project, all files are LV 2011, it builds and runs correctly. I have mass compiled. It did call 2 dynamic vi's but I have removed those. The project did contain conditional compilation, but that is removed. It did contain disabled diagrams, but they are removed. I did a save hierarchy to a seperate folder, just to make sure the standard save works. It does. There are 1196 vi's and controls in the project.
If I save to LV 2010, quite a number of sub vi's are saved (909 including controls), but none of the top level ones. The crash is manifested by Labview leaving memory (task manager doesn't see it any more) and the Labview window dissapearing.
Attached is the save dialog at the instance before crashing.
I have not been able to locate a log to let me know the last loaded vi. If you know of such a log, please let me know.
Has anyone experienced similar problems? If so, any clues on how to fix this?
Thanks,
Bart Schroder
Attachments:
LV2011 save crash.jpg ‏17 KB

BartSchroder wrote:
I have not been able to locate a log to let me know the last loaded vi. If you know of such a log, please let me know.
In the advanced build configuration, check "generate build log file". See if you get more information. Good luck.
Quote from the help:
Generate build log file—Specifies whether to create a log file for the build. The build log file lists all files contained in the build, including subVIs you do not specify as Startup VIs or Always Included. The log file also contains general build information such as build start and end time, the build specification and project name, and any errors that occurred during the build.
LabVIEW Champion . Do more with less code and in less time .

Why can't LabVIEW 2011 find my PXI?

I'm migrating some real-time Projects from older versions of LabVIEW (8.6 and 2010) to LabVIEW 2011. For the older systems, I installed the appropriate Real-Time software (matching version numbers) on a PXI controller, which MAX saw just fine. When I opened my Project, I chose a New Target and had it look for an existing Real-Time PXI -- it always found the PXI without trouble.
I've just taken another PXI controller (8176) and installed LabVIEW 2011 RT on it. Curiously, during the installation process, MAX identified it (and still does) as a Generic Desktop PC, and when it finds it, gives it a PC-looking icon instead of a PXI chassis icon. When I open my Project in 2011 and try to add this PXI as a target, it finds no Real-Time PXIs. Why is this?
There's a VI called RT Ping Controllers that can find all the PXI controllers -- it finds my PXI, and identifies it (correctly) to me by the name I assigned it, so LabVIEW 2011 can definitely "see" this controller, even if Project (apparently) cannot.
I'm beginning some tests involving TCP/IP (and Network Streams) with this controller and configuration. I've had success with doing this in LabVIEW 2010, but in a (single!) test I've done with this new LabVIEW 2011 RT system, I couldn't "connect". I haven't beaten this system enough, nor done a side-by-side comparison of equivalent code on a LabVIEW 2010 and LabVIEW 2011 system, but would appreciate it if anyone (else) has had issues (or, better, successes) with PXI-related Real-Time in LabVIEW 2011.

Hello,
What version of Measurement Automation Explorer and the NI-DAQmx driver do you have? Also, here is article that you may find of some use:
Why can't I add my Real-Time Target in Project Explorer?
http://digital.ni.com/public.nsf/allkb/40BF6300E77E8AD4862574EF006F2793?OpenDocument
Regards,
Patricia B.
National Instruments
Applications Engineer

Driver for N9010A for Labview 2011

I am looking for a driver for Agilent N9010A Spectrum Analyzer for Labview 2011, I see the drivers for 8.6 and 2010 but we need it for 2011.
Thanks

2011 can load anything from version 6.0 and up so you don't need a specific 2011 version.

LabVIEW 2011 Development System fails to install

I have just tried several times to install my new copy of LabVIEW 2011 Dev Suite, but get an unknown exception (with no details - see attached picture) right at the start of installing the development system (English 32-bit). I have rebooted and closed all applications including virus scanning but still the same. I am using WinXP Pro SP3, and already have LV 8.6, 2009, and 2010 installed. I'm completely baffled as this type of problem has never occurred before and there is no information about the cause of the exception.
Mike
Solved!
Go to Solution.
Attachments:
LV2011 Unknown Exception.JPG ‏10 KB

Hi John,
After clicking on Details, the words "No information" or similar are displayed. I have tried again today but with the same result. I have attached a new screenshot showing the installer initialisation progress window. I have checked the DVD and it looks undamaged, and there is plenty of free disk space.
Attachments:
LV2011 Unknown Exception.JPG ‏64 KB

How to run the VI developed in labVIEW 2011 in its previous versions

Hi all,
I am currently using LabVIEW 2011 in my home PC.
But, all my school computers are installed with LabVIEW 2010 and 2010 SP1.
How to run the VI developed in LabVIEW 2011 in its previous versions?
Is there any conveter for that?
Regards
Prasanth T
Solved!
Go to Solution.

Open the VI in LabVIEW 2011 and use the File menu option, Save for Previous Version.

Profibus in Labview 2011

Hi,
I recently updated my Labview from 2010 to 2011. And then I tried to install the latest Profibus driver (DF_PROFI_II_LV_1.36.2.zip) which I downloaded from (http://joule.ni.com/nidu/cds/view/p/id/2687/lang/en). Release date: 10-10-2011
Normally, this addon should be installed at the following path (C:\Program Files\National Instruments\LabVIEW 2010\vi.lib\addons). However, I did not find it in the"addons" folder of Labview 2011. Did anyone else ever come to this issue? To solve this issue, should I just copy Comsoft.lib in "addons" folder of 2010 to the one in 2011? Anything else I should do?
Thanks,
Zhi
Solved!
Go to Solution.

I t looks like it detected the LV 2010 version as the current one and did not install anything into 2011. You should be able to copy the files over to the same path mentioned.
DirkW

Error in invoking the build rule editor, LabView 2011

Hi all. I'm having a problem in Project Explorer. When I right-click on 'Build Specifications' and select New:Application (EXE), I get the following error dialog:
"There was an error in invoking the build rule editor. Please check the corresponding provider directory to see if any VIs are broken."
After this appears, no build specification is created.
I built this application in LabView 2010 on WinXP and was able to compile and run it sucessfully many times over the last few weeks.
The problem started yesterday when I had a problem with a Ring control. I right-clicked it and selected "Edit items" or "Properties" the cursor blinked for a moment but the dialog box did not appear. I removed the Ring control and replaced it with a String control, then when I tried to build the application, I got this error message. At that time, I also noticed that I could not get a Properties dialog box to appear for any controls or indicators.
Yesterday, I installed NI Developer Suite 2011 Version DS2. This seems to have fixed the problem with the dialog boxes and I was able to use the Ring control. However, I still have the problem with the build rule editor.
To determine if there was a problem in my program, I built a new 'Hello World' .vi with just a string control and string indicator. This program has the same problem when trying to build to an .exe.
Currently, I am trying to remove all previous versions of LabView. When that is done, I will reboot and try to build again. If that doesn't work, I will remove ALL National Instruments software and re-install NI Developer Suite 2011 DS2.
I'm hoping someone can provide a solution before it comes to that.
Two other facts which might be relevant: I don't have Administrator on this machine, although I could probably get it if I could make a strong case. Also, I can't be sure, but I think the problem may have started when I undocked my laptop from the docking station to go to a meeting.
I appreciate your help. Thanks in advance.

If you need additional assistance, I encourage you to create a new thread. It is more likely to be answered by other users as a fresh post.
The most likely cause is a corrupted file (or files) in the builder directory.
I would recommend renaming/moving the following folders and performing a repair install of LabVIEW:
\National Instruments\LabVIEW 2011\vi.lib\AppBuilder
\National Instruments\LabVIEW 2011\resource
Regards,
AnjelicaW.
Regards,
Anjelica W.
National Instruments
Applications Engineer

Labview 2011 - Textbook

Hi all,
I am completely new to Labview and will be using it for one of my projects for university. I am a complete beginner to Labview and been having a look for a good text book and Labview for Everyone seems like a good choice.
But, it seems like it was based on Labview 8. Given that I will be using Labview 2011, I was wondering if there will be drastic differences between the two? For example would it be as different as Ms Word 2010 is to Ms Word 2003. Basically would be the book still be worth purchasing?
Would my project supervisor at university, who is farmiliar with Labview 8.5, be able to use Labview 2011 comfortably?

Yes, a book for LabVIEW 8 is suitable to learn LabVIEW. The changes are small.
Anyone comfortable with LabVIEW 8.5 will have no problem using LabVIEW 2011.
LabVIEW Champion . Do more with less code and in less time .

LabVIEW 2011 WSN Module?

I just received a NI WSN Starter Kit and it came with LabVIEW 2010 evaluation disks and the WSN Module Pioneer 2010. On my work laptop I have recently removed LV 2010 to upgrade to 2011. The WSN Module won't install without LabVIEW 2010...
Is there a walk-around or a new version of the WSN Module for LabVIEW 2011? Or do I have to install LabVIEW 2010 again?
Thanks.

Hello GrigS,
This is Andrew Brown, an Applications Engineer from National Instruments. There is a newer version of the NI-WSN driver (1.3) that is compatible with LabVIEW 2011. You do not need to install LabVIEW 2010 again.The download page for the driver is:
NI-WSN 1.3 - NI Wireless Sensor Networks - Windows 7/Vista/XP x86
Please note the installation instructions on the page are:
Installation Instructions
Perform the following steps to install NI-WSN 1.3.0:
Install LabVIEW
Install LabVIEW Real-Time Module (required for NI 9792 and NI 9795 support)
Install NI-RIO Driver Software 4.0 or later (required for NI 9795 support)
Download and run the self-extracting executable NIWSN130.exe. This will install NI-WSN 1.3.0 and all necessary driver files.
Regards,
Andrew Brown
Applications Engineer
National Instruments

LabVIEW 2011 download

Good afternoon engineers,
Where I find the LabVIEW 2011 to download? Only find the 2010 and 2012.
Regards,
Hugo Santos
Student at ISEC - Master Mechanical Equipment and Systems

Here:http://joule.ni.com/nidu/cds/view/p/id/2871/lang/en
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

LabVIEW 2011 to 2010

Similar Messages

Maybe you are looking for