LabVIEW 4.0 Invalid Page Fault Errors

I've got myself stumped on this problem - we had a LabVIEW based PC/DAQ system that started giving invalid page fault errors and crashing in Win95. This may have been concident with a revision to a vi file. To rectify the problem I've tried the following:
1. Reinstall LabVIEW 4.0 with NI-DAQ 6.6
2. Wipe HD, reinstall Win95, LV 40, NIDAQ 6.6
3. Full HD scan and MEMTEST86 memory test
4. Install on another PC
The PCs are P5-60 Gateways with 128 MB of RAM. DAQ config is 1 AT-AO-10 and 1 AT-MIO-16DE-10
Nothing seems to help. With a reinstall of LV40, I can get it to run, but once I copy the .vi files back into User.lib LV crashes.
Does LV40 look in User.lib upon startup and crash if it finds something it doesn't like? A corrupted vi?
Thanks!

Blair Hogg wrote:
...guess the next step is to go in and load each .vi manually to see if there is one that is causing problems. Hopefully some of you out there are finding this somewhat interesting, and I'm not just cluttering up the forum...
Hi Blair Hogg,
I like your sence of humor ;-) Don't worry, even if nobody reads your
thread (well... I just did) you need to write MUCH more for it to be
considered clutter. Now, if you had created 25 duplicates of the same
thread, then we would be talking about cluttering...
I'm curious about this issue even thought NI only supports LabVIEW two
versions back - officially. My guess is that a VI is corrupted and
kills LabVIEW when the VI loads. Therefore I do aggree that the
procedure from now on is to load every single VI one by one and then
notice what VI will make LabVIEW crash. I might be able to repair that
VI if you submit it to the thread.
Another thing to try is to mass compile the user.lib. The log after the
mass compile will show if any VIs were bad or had problems getting
compiled.
Well, I hope you find the source for this issue - even if I'm the only one that cares ;-)
Have Fun!
- Philip Courtois, Thinkbot Solutions

Similar Messages

Invalid Page Fault Error Messages - ICC Profiles and Fonts

Possible causes of these error messages include bad ICC profiles and/or bad fonts. See below for corrective measures

Q: Message reads:
PHOTOSHP caused an invalid page fault in module
KERNEL32.DLL at 017f:bff7b9f5. Registers:
EAX=796692e0 CS=017f EIP=bff7b9f5 EFLGS=00210202 EBX=00d0fe28 SS=0187 ESP=00c10000...
A: You have an incompatible or corrupt ICC profile in your
Windows/System/Color folder (win 98/98SE/Me) or ./system32/spool/drivers/color (win2k).
Make a temporary folder, ICMs, under and move all the
ICM and ICC files to that folder.
Start PS and make sure it restarts OK.
Now move back JUST THE PROFILES YOU NEED to Windows\System\Color (win 98/98SE/Me) or ./system32/spool/drivers/color (win2k)
Also see: http://www.adobe.com/support/techdocs/1c4f6.htm

Invalid Page Fault Error

I an running PLUS80W on a P3 1GHz machine and
when I start up the SQL Plus 8.0 application I get an invalid page fault in ORA805.dll
If I use forms6i or reports 6i no problems.
Is this a known problem and how do I solve it.
Thanks
null

This sounds like a problem to work with Oracle Support on.
- CJ

Invalid page fault error in module kernel32.dll

I'm a VB programmer attempting to learn java. I downloaded the j2se 1.40 sdk (At present I am running Windows 98) and installed it. The download and installation process was smooth. However when I attempt to launch the program, I get the illegal operation dialog with details as follows:
SPLASH caused an invalid page fault in
module KERNEL32.DLL at 0177:bff766bc.
Registers:
EAX=0055003c CS=0177 EIP=bff766bc EFLGS=00010202
EBX=00000000 SS=017f ESP=00550000 EBP=00550010
ECX=00000000 DS=017f ESI=00550108 FS=305f
EDX=bff76855 ES=017f EDI=817b5b68 GS=0000
Bytes at CS:EIP:
e8 13 ad ff ff 8b 55 08 8f 82 b0 00 00 00 8b 4d
Stack dump:
002a0014 00000000 0055003c 0055003c 00550024 bff766fd 0055003c 005501b4 00000000 005501b4 bff883ed 0055003c bff79060 00000000 0064ffec ffffffff
I suspect this has something to do with the OS. Can anyone shed some light on this for me.
Thanks
Nancy

What command did you use to launch the program?
The readme file explains how to set the path and classpath; if you've done that, try this command in a DOS window:
java -version
C:\>java -version
java version "1.4.0"
Java(TM) 2 Runtime Environment, Standard Edition (build 1.4.0-b92)
Java HotSpot(TM) Client VM (build 1.4.0_01-b03, mixed mode)
Good luck,
Mike Rainville

Invalid page fault (only on one computer)

I keep receving a whole set of invalid page fault errors when I try to open my VI.
It is strange because the VI works perfectly on another, less powerful, computer running the same OS (Win98) and same version of LV (6.1)
Does anyone have any advice?

What all is in your code? Are you doing anything with ActiveX? Which module does the fault occuring in? This is possible a hardware issue at this point. It is possible that this could be cause by faulty memory. A page fault is generated when errors occur while moving pages in between your system memory and virtual memory. Is this a very large application? Try running other large programs (large Word or Powerpoint documents, etc.) to see if you can reproduce the page fault there. Are there any other VIs that will generate this same fault? What other software do you have on your system?
Just a few guiding questions that might help determine were this page fault is generated.

JAVA caused an invalid page fault in module KERNEL32.DLL at 016f:bff7b9a6

Hi All,
This problem is bugging me for last two days. Actually I am trying to embed Internet Explorer inside Java application. Everything is working fine till I dont close the application window. But just when I close the window everything goes down. I am working on win98 platform and not sure if it is this reason. The exact error message I am getting is:
JAVA caused an invalid page fault in
module KERNEL32.DLL at 016f:bff7b9a6.
Registers:
EAX=00000000 CS=016f EIP=bff7b9a6 EFLGS=00000246
EBX=00000001 SS=0177 ESP=0c08fb7c EBP=653cfbd0
ECX=004271ec DS=0177 ESI=653cfbd0 FS=443f
EDX=00427310 ES=0177 EDI=0042701c GS=0000
Bytes at CS:EIP:
ff 76 04 e8 13 89 ff ff 5e c2 04 00 56 8b 74 24
Stack dump:
004272e4 653a8f88 653cfbd0 0042701c 004272e4 004271fc 00000000 653aaf7b 0042701c 0b1df32c 5f3ed308 0c08fc70 00000000 5f3e5adc 004272e4 5f3ed6d8
Also since JVM is also crashing it is creating a log file which reads:
An unexpected exception has been detected in native code outside the VM.
Unexpected Signal : EXCEPTION_ACCESS_VIOLATION occurred at PC=0x6D0670CD
Function=[Unknown.]
Library=(N/A)
NOTE: We are unable to locate the function name symbol for the error
just occurred. Please refer to release documentation for possible
reason and solutions.
Current Java thread:
     at sun.awt.windows.WToolkit.eventLoop(Native Method)
     at sun.awt.windows.WToolkit.run(WToolkit.java:240)
     at java.lang.Thread.run(Thread.java:536)
Dynamic libraries:
0x7CC00000 - 0x7CC1D000      C:\WINDOWS\SYSTEM\IMAGEHLP.DLL
Local Time = Tue May 14 18:46:45 2002
Elapsed Time = 616
# The exception above was detected in native code outside the VM
# Java VM: Java HotSpot(TM) Client VM (1.4.0-b92 mixed mode)
I am not getting any clue about this error. Please help me out. :-(

aman ghus jao bans balli bamboo lekar..

F50DBG32 caused an invalid page fault in module MSVCRT40.DLL at 0167:7967d7f0.

HI all,
I trying to run a multi-tabbed form built in forms 5.0 with Oracle 8.1.7 db running on a solaris m/c.
The client m/c os is windows '98.
but when trying to run it, i get the following error:
F50DBG32 caused an invalid page fault in
module MSVCRT40.DLL at 0167:7967d7f0.
Registers:
EAX=796aadff CS=0167 EIP=7967d7f0 EFLGS=00010286
EBX=00aef3f4 SS=016f ESP=00aef284 EBP=00aef290
ECX=008e56c0 DS=016f ESI=00357365 FS=586f
EDX=0000001f ES=016f EDI=008e579c GS=0000
Bytes at CS:EIP:
8a 06 46 8a 27 47 38 c4 74 f2 2c 41 3c 1a 1a c9
Stack dump:
00aef3f4 00aef43c ffffffff 00aef2a8 617e7573 008e579c 00357365 008e56c0 008e56a8 00aef3a8 617d8bae 0101343c 008e56c0 00aef43c 00000001 00aef3f4
. The problem is tat the same form runs fine in a Win-NT machine.
Unfortunately, we have a mixed group of users for this form. some of them have NT and some others have Win95/98...
Any help?
Regards
-Sree Ram

Hi all,
Found the prob' or atleast the workaound for this...
APart from setting the fill property of the canvases to Transparent, set the same for all the DB blocks too...
Now my form is working fine in both OS.
Regards
-Sree Ram

Invalid page fault in module cvirte.dll

I have updated two old programs using LabWindows 7.0 which were perviously created with an earlier version of LabWindows. I am having problems though updating a third program. I get an error stating...
Characerization (the name of the program) caused an invalid page fault in the module cvirte.dll at 0167:684b77f5.
The operating system that I am installing these program on is Windows 95.
I'm not sure where this error is coming from but I'm assuming there might be a problem when I build with LabWindows 7.0 and install to Windows 95. But, the previous two programs updated before this one have had no problems at all. Any help is greatly appreciated.

JuanCarlos,
Thanks for you help. Since I have been getting this error, we did some system monitoring and noticed that when the system crashes, the CPU is running at 100%. It also crashes during debug mode as well. I have been putting in break points to specifically find a location. What we have come down to is that its writes the test information to a file, but crashes when the file is recalled within the program to process some results. As far as GPIB drivers, everything is correctly installed and since we are using old ISA slots, I have made sure there are no IRQ conflicts.
The funny thing is...this exact program works perfectly fine on another station but crashes on this current station! We need both fully functional though.
Is there a
nything I should look for specifically to tell if its a GPIB problem? Anything specific for CVI problems?
Thanks for you help!
Paul

Invalid Page fault in IMM32.dll on Japanese Win 98

Hi
First of all, let me say that I'm new to internationalization fundamentals.
My Java application uses i18n.jar for internationalization support(primarily Japanese) and everything seems to be fine on all OSes(Win2k,NT,98,Solaris etc), except that in particular menu options in Japanese version of Win98(m/c has MS-IME 98 running), a Windows fatal error pops up saying "Javaw caused a invalid page fault in module IMM32.dll". IMM32.dll, I understand, is the dll required for i18n support in Windows.
This error comes up if we exit immediately after launching application or when trying to launch new windows for charts etc.
Could you please suggest a workaround or a fix to this issue? What could be the root cause of the problem, I mean, does i18n.jar use the IMM32.dll, or is it just a conflict? Have there been other such cases?
Thanks for all your advice in advance
Regards
Santosh

If Javaw is causing the page fault, that's very much a bug in native code (i.e. Windows-only stuff) within the VM.
Search through the bug database on this site, and you'll more than likely find a corresponding bug report for this if it's been around a while and is fairly easy to produce. If you can't find it, submit it - I'm sure the Sun guys would be concerned to hear that Javaw is crashing and burning.
Hope that helps!
Martin Hughes

_INS5567 caused an invalid page fault in module PFMODINTL.DLL at 0167:01651

Can someone help me with this I had to reinstall windows 98se and because of that I had to reinstall the drivers for my sound blaster pci28 sound card and that error comes up every time it trys to install the drivers for it, it happens when it gets to the 00% mark of the setup for the installation. This is the full error's details.
_INS5576 caused an invalid page fault inmodule PFMODINTL.DLL at 067:065e0.
Registers:EAX=005b0000 CS=067 EIP=065e0 EFLGS=0000202EBX=003037 SS=06f ESP=006bf78c EBP=006bfcb8ECX=2000690 DS=06f ESI=00000000 FS=447EDX=006bf7a8 ES=06f EDI=00000000 GS=0000Bytes at CS:EIP:8b 08 52 56 50 ff 5 40 85 c0 7c 0a 39 5c 24 44 Stack dump:006bf7dc 006bf7a4 00000000 00000000 005b0000 0980c20 00000000 0700000 006bf7d0 0044790 0054afc2 00000004 00040005 0054ad8 00440004 003037
please if you can help me with this please do thank you.

Hi all,
Found the prob' or atleast the workaound for this...
APart from setting the fill property of the canvases to Transparent, set the same for all the DB blocks too...
Now my form is working fine in both OS.
Regards
-Sree Ram

Acrobat Pro V8.1.2 "Invalid Page Range" Error - Rotate Pages

Hi,
I have Adobe Acrobat Professional version 8.1.2. For the last couple of weeks every time I try to rotate a page in any direction I get the following error:
"Invalid Page Range" (OK)
I have tried every combination of options for amount of rotation and page range (all, selected, specify). No matter what I do I get the same message. I have tried this on several different documents both encrypted and unencrypted.
Does anyone have any ideas?

I know this is nearly 4 years late, and I realise this may not have been the cause with the original post, but for the sake of covering this issue for anyone who searches and lands on this page: The most common cause for receiving this "invalid page range" error when attempting to rotate pages is becaue the option for "Even and Odd Pages," "Even Pages Only," or "Odd Pages Only" drop-down choices are inconsistent with the selection. For example, if you're trying to rotate just page 1, but the selection "Even Pages Only" is slected, then you will receive this error. You will find this option in the options window that appears when you click the Rotate command.
Just my two cents after trying to remedy this over and over with users.
Cheers!

Hotsync Crashes (invalid page fault) - address book

Help - I know I have an old setup, but I really need help ...
I'm trying to sync between a Samsung i500 and my win 98se computer using Palm desktop 4.1 and Hotsync Manager 4.0.4. It's been working great for YEARS but I did something and now it always crashes. I CAN'T update - I have a full office of these computers running software that CAN'T run on newer systems.
I usually sync between REA (a little organizer program) and Palm and my phone, but that crashed so I EXPORTED the address database (in a comma delimited form) then brought up the database in Works and cleaned it out of comma's and any bad records I could find.
I've tried uninstalling Palm Desktop AND doing a HARD reboot on my phone, then syncing with NO addresses. That worked once. But then when I imported the addresses in Palm Desktop, on the next HotSync it crashed again (invalid page fault).
My address book is about 10,700 records, I don't know if that is the problem. HELP
Post relates to: None

No one replyed ... but I managed to call Palm One (866-751-7256) paid tech support. Herb correctly pointed out article 24515 that points out a maximum of 10,376 records that can be synced. So I need to (somehow) delete some records. Then I'll try reloading software and syncing.
Post relates to: None

Invalid page faults

Good day. I am attempting to install 8i Lite on an HP Kayak XA.
It is a pentium based box with 32 mb ram and adequate disk.
When I run the 8i install it presents the background grey screen
and then it says;
An Invalid Page Fault has occurred in module OIBKND32.DLL and
will terminate, (or quit or whatever it says at the end). Anyway
it dies.
If you have any ideas on this please let me know. I have
rebooted and powered off and on just in case and to no avail.
Eric,
null

Yes I also have the same problem.
In the meantime, do you have any solution for this. Please reply to me.

NIMAX caused an invalid page fault in module PDM.DLL at 0167:4a01259d

When I closed the MAX 2.2 and get the following problem~~
NIMAX caused an invalid page fault in
module PDM.DLL at 0167:4a01259d.
Registers:
EAX=00000000 CS=0167 EIP=4a01259d EFLGS=00010246
EBX=00761f04 SS=016f ESP=022cfe44 EBP=00000000
ECX=007700b0 DS=016f ESI=00781a10 FS=3f87
EDX=00000004 ES=016f EDI=00761ef4 GS=0000
Bytes at CS:EIP:
8b 10 ff 52 08 83 c6 04 eb c9 53 ff 15 f4 00 02
Stack dump:
00000000 00849070 00761ee8 00000001 4a01275a 00761ee4 00849070 00000000 4a012fed 00761ee8 4a012b06 0084a020 00000000 00000000 00000000 00760630
Can anyone help me to solve this problem?

Hello Ivan ,
Thank you for your inquiry regarding problems closing MAX 2.2. It sounds like MAX crashes causing an invalid page fault in module PDM.DLL. This problem can happen when Microsoft Visual Studio is installed. The following link is a great resource when dealing with this issue.
http://digital.ni.com/public.nsf/websearch/1F1B0B6A05772B6A86256BC1005634D3?OpenDocument
Other resources similar to this can be found on the ni.com website by clicking the support tab at the top of the home page. Then search for �PDM.DLL� from Technical Resources at the top of the page or topics similar to this. I hope these resources help. Let me know if I can further assist you.
Shea C.
Applications Engineering

"Program" caused an invalid page fault in module SQORA32.DLL in 0177:02f92c

We has an Visual FoxPro that generated an invalid page fault en module SQORA32.DLL
We use Windows 98 SE, ODBC 9.2.0.6.5
Server Windows 2003, Database 9.2.0.7
any ideas...

Hi all,
Found the prob' or atleast the workaound for this...
APart from setting the fill property of the canvases to Transparent, set the same for all the DB blocks too...
Now my form is working fine in both OS.
Regards
-Sree Ram

LabVIEW 4.0 Invalid Page Fault Errors

Similar Messages

Maybe you are looking for