LabVIEW example problem

i have install labview 7.1 development software with driver , on windows xp
i am not able to open example . it shows following errors "CAN NOT FIND LabVIEW SERVICE PORT FROM SERVICE LOCATER YOU WILL BOT BE ABLE TO BROWS DIRECTRY STRUCTRY" while when i make any programme it works
please help to solve this problem
thanks
R.R.YADAV
[email protected]

Hi,
LabVIEW Example Finder uses NI Service Locator in the background. Try to restart the Service Locator and see if that helps. More information on this can be found at the following link.
http://digital.ni.com/public.nsf/websearch/8C00F1144B2CD73E86256DEF00698AC3?OpenDocument
Also, make sure that there is no antivirus or firewall application running in the background when you try to open the example.
Regards,
Ankita A.

Similar Messages

Neovi labview example

still the problem for the neoVI Labview example.
i can receive the message from another software, but i can't transmis the message.
i always arrive the good result:
thank you

Hello summerwar,
Are you talking about this? If so, I could not find much information on their website or in your post, so it is difficult to know what is going wrong...
By the looks of it, I'm guessing you are using the serial port of your PC to connect to their device which converts these to CAN messages. If you cannot transmit any messages, maybe your TX line is not connected properly to the RX line on the module. What kind of cable are you using?
Do you know if you need to send a command to represent that you want to send a message? Its difficult for us to help without the VI and the product manual at least.
I hope this helps...
O. Proulx
National Instruments
www.ni.com/support

Sorting Machine.SLDASM file from the labview \examples\Motion\SolidWorks\SolidWorks Files

Hi.
I'm new with labview. I need to use labview for my project for virtual pototyping.
Foe beginning, I'm trying the tutorials from http://www.ni.com/white-paper/9566/en/
I'm trying to open the below link both in LabVIEW and SolidWorks to understand the assembly operation.
<labview>\examples\Motion\SolidWorks\SolidWorks Files directory
I've looking for the 'Sorting Machine.SLDASM' file.
I've search everywhere but I can't find the directory for the file.
Really appreciate if anybody can tell me where I can find the link.
Thanks in advance.

The problem seems to be with Scan Engine.
Here is a screenshot of the error mesage when deployment:
Configuration:
OS: Windows 8 Final
LabVIEW Version: 2012 with all updates installed
NI SoftMotion Version: 2012
Solidworks Version: 2010 SP4
I doubt the problem lies in OS as all examples are running flawlessly except that with Mechatronics Examples. Hope to get any response from NI SoftMotion Team. Thanks for your assistance in advance.
Waleed El-Badry MSc.,MCPD, ISTQB Certified Tester
Assistant Lecturer
Mechatronics Department
Faculty of Engineering
Misr University for Science & Technology

Labview examples for an "http transponder"

I’m looking for Labview examples (LabView 5.1 or 6i) to make an “http transponder” between an intranet and internet networks.
I’ve a “system” configured with a TCP-IP address in the local intranet network, it isn’t a PC but its behaviour is like a local “web server” without external access, so it is possible to send it URLs from an every PC (with internet explorer) inside the local network, to get the “system” status.
I’d like to monitor that “system” in the internet network also, so I need to make an “http transponder” on a PC connected in the local intranet network, but with external access permission.
So it can be possible to s
end URLs to the transponder by a PC in the internet network, and the transponder can redirect them to the “system” in the intranet area.
The “system” can send his status along the inverse route.
Thank you in advance.
Natalino.

Thank you, it would be useful, but I haven't an "Internet Toolkit" at the moment.
I made some attempts with low level Tcp-ip functions, and I obtained good results by loading static html pages, bad ones by loading dynamic pages.
I think is an integration problem (timeout, waiting times, etc..), so some "previously tested" examples with Tcp-ip function would be very useful.

I would like to detect all the keyboard key is okay, but not every key can be detected by using LabVIEW example, keyboard keycode

I would like to detect all the keyboard key is okay, but not every key can be detected by LabVIEW example ( we can use 『basic input demo.vi』to detect normal key』.
I want to detect some 『hot key』 for example some keys exist in the upper part like 『search key』、『e-mail key』、『volumn control key』...etc. They are very often to be watched in some new keyboards, but we still don't know how to detect if their functions are okay.
Can we detect signals of these 『hot key』 in LabVIEW? We can apply these hot key's functions in XP, so we should detect their signal, I think, but I can't do it.
I serach some information about this question, and somebody said we can detect hot key's signal by grabing 『keybode』 these hot key feedback. But I don't know how to do these. I can't use VC. So anyone can give me a LabVIEW VI to grab keycode? Or any other solution we can detect all the key on the keyboard, including hot keys?
Thanks!
Regards,

Maybe that is the limitation of Acquire Input Data.vi.The vi can't identify the Unformal key.
You can try to use Event structure and set to listen "key down" event.
There are two terminals VKey, ScanCode will sent out the information when you press key.
There are two pictures in attached file, 2.jpg will show you the detail.
Good luck.
Attachments:
SpecialKey.zip ‏17 KB

OO question in LabVIEW example

Hello,
I am trying to learn OO and I have a question in the LabVIEW examples. See the attached image
What is the protected VI's? It looks like a collection of VIs with a type def. Isn't this a class? Why isn't it a class? What is going on?
Thanks

No image attached. Which example are you looking at?
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

Converting instek psw labview examples from v8.2 to v7.1

The labview examples v8.2 of the instek psw series in needed in a 7.1 version. All I need is to control the constant current and constant voltage. I can supply the examples and visa.vi's or they can be obtained at instekamerica.com under downloads/software/power supplies/psw series. I need this because other legacy hardware must run on v7.1 labview. Here are the attached zip files.
Thanks.
Attachments:
PSW-Series+LabView+for+ver+8_X.zip ‏553 KB

Here it is in LV 7.1
Kees
Attachments:
PSW_VI Tree Folder.zip ‏736 KB

I am looking for labview examples related to ECG

Hi, everyone!
I need your help.
I am looking for labviews examples, which are related
to ECG for my thesis .
I wait for your answer.
thanks in advance

Burcu;
I am not sure what type of examples are you looking, so this is a start:
Searching at the LabVIEW Discussion forum I found:
Example
calculate heart rate from ECG
how to design a suitable vi to acquire ECG waveform?
Doing a search with Google:
LabView Exercise to model and analysis ECG/EKG data
EE 206 MINI-PROJECT I CARDIAC MONITOR VI
Searching an NI.com:
PC-Based ECG Monitoring and Analysis Using BioBench (LabVIEW VIs at bottom - not sure if link is dead)
Regards;
Enrique Vargas
www.visecurity.com
www.vartortech.com

Labview example for data capture using 5102 scope card

How can I program a Labview Vi to control, and capture a waveform using the 5102 scope card. I need to be able to set it up to continually capture a waveform (Channel 1 and Channel 2) when triggered on a rising edge of channel 1 and then store the data on disk automatically, then wait for the next trigger.
Any help or tips as to how I could do it would be helpful.
Thanks
Allan

Allan,
Please find the attached zip file that has some useful LabVIEW examples with scope 5102
Zvezdana S.
National Instruments
Attachments:
scope.zip ‏181 KB

LabVIEW Example For Younger Crowd.

Hello,
I am giving a presentation for a group of younger kids this friday, June 29th and I need a LabVIEW example that I can show them and talk about. So I need something that younger kids, ages 5-13 can understand. Its ok if its too boring for the older kids and too confusing for the younger and vise versa. I can adjust how I talk to compensate. So far I have a bouncing cube demo, but that is not complex enough to talk about for a length of time. I would also like the example to relate to engineering as much as possible and is not just a game like Tic Tac Toe. Thank you for your suggestions.
Michael Boyd

It is always good to do something where the students can be involved during execution. For example you could fill two parallel tanks with random numbers and take bets which one fills first. (learn about loops, shift registers, comparison (see if it is full), decision, etc.)
You might also do some real DAQ with the soundcard. Again do a "race" where the two tanks fill according to sound volume. Do a FFT and tie one to the high frequency (girls!) and one to a lower frequency (boys!) and let the class scream their heart out to advance each tank/slider.
Other soundcard things would be a simple voice scrambler or changer (doesn't work that well without RT). SImply record some sentences, do some digital signal processing, then play it back. See how the sound changes depending on settings (double/half the frequency, low-pass, hi-pass, etc.)
If you have more time, you could also e.g. test batteries and see what brand is best. See:
http://forums.ni.com/ni/board/message?board.id=170&message.id=107032#M107032
LabVIEW Champion . Do more with less code and in less time .

Where can I get LabView examples for PXI-6551 or 6552? Thanks

We are thinking of buying a 655x and wanted to see sample code to get an idea of its capabilities.
Does anyone know where I could find LabView examples?
Any other information related to the PXI-655x would be appreciated too!
Thanks,
-KP

Hi KP,
Thanks for your interest in the NI 655X. These products use a brand new driver, NI-HSDIO, which is based on DAQmx. We are still working on a more bandwidth-efficient web installer for the driver, but for now I have placed it on our temporary ftp site. You can find it at ftp://ftp.ni.com/incoming/HSDIO.zip
This driver contains a full set of example programs for both LabVIEW and CVI, and the help files are a great way to learn about the physical capability of the board.
Do you have any other questions about these products?

Is anybody has the example problem for AD/DA converter controled by PIC16F84?

In my circuit( Multisim 9), I use PIC16F84 as the
MCU to control the DAC and ADC. I want to ask if anyone has the example
problem for the controlling?
Further more, the I/O port of
PIC16F84 seems can not be connected with the digital output of DAC, so
I asked myself, is it right that for PIC16F84, the I/O port can only
connected with the serial port of DAC and ADC? Or it needs a converter
to adapt to the input port of DAC?
Looking for any help! Thanks!

You can test the new Design Circuit Suite (includes Multisim10 with MCU10 and Ultiboard 10 with Ultiroute10). When you open Samples you find the folder MCU with PIC folder. In these you can find some examples to PIC16F84. With that as pattern you should solve the problem.
I attached you here the MCU examples in the *.zip
For downloading the 30 days free test version you can use the link:
http://www.ni.com/academic/multisim/ and click to evaluation software
or these link:
https://sine.ni.com/apps/utf8/nigb.confirm?p_gb_prof_id=7350&p_lang=US&p_dl_url=&p_dwnld=N&p_code=GB...
Attachments:
MCUPicScreenshot.zip ‏964 KB

Join the LabVIEW Example Code Contest and Get a Chance to Win an iPad!

This October, we are holding the LabVIEW Example Code Contest 2010. LabVIEW users can demonstrate the cool things they've been able to accomplish with LabVIEW by submitting new example code. The best example code wins an iPad.
Each participant can submit as many entries as they want as long as they fall under at least one of the following categories:
Data Acquisition
File I/O
Math/Analysis
User Interface Controls
VI Server/Scripting
Games
Submissions will be accepted from October 1 through 17. Judges will choose finalists for each category, then the NI Community will vote for their favorite example codes. Father of LabVIEW Jeff Kodosky will choose the overall winner.
Read the rules, ask questions, and submit your entries in the LabVIEW Example Code Contest 2010 Group

The submission deadline has been extended to Monday, October 25

In the Full Featured LabVIEW example, what makes the entry point button reappear?

My question is this: What piece of LV code or invoke node for the TS engine makes the Entry Point button reappear when a sequence file is loaded?
Background:
I've inherited a modified version of the Full Featured LabVIEW UI, which has been moderately modified (Enough so that restarting isn't really an option, but it's still similar enough to use them as comparisons for behaviors). Also, this code was started in LV2012/TS2012, and I'm migrating to LV2013/TS2013, but this behavior was consistent in both versions.
Here's what I've tried:
I found that when the Connect Command executes (See attachment), the button, which is a TSUI.IButton control, is gets greyed out or hidden. In the unmodified example UI that's provided with TestStand, the button reappears when a sequence file is loaded. The problem is that when I load a sequence file in my code, and click on it ahead of running, the button does not reappear. In my code, I can run the sequence successfully by right clicking on the sequence file and selecting Run, so I don't believe the sequence has an error, nor the process model.
Thanks in advance,
Seth
Solved!
Go to Solution.
Attachments:
ConnectCommand.JPG ‏56 KB

Seth,
The "options" input of the ConnectCommand function controls this. On the Help page for this input, you can see that there are options for "ignore enable" and "ignore visible". Either of these could impact the functionality of the entry point button. You might try making the options for both buttons 0 and see if this resolves the issue. If not, please let us know.
Daniel E.
TestStand Product Support Engineer
National Instruments

Labview Graph Problem

Hello,
I have a problem with a tool witch takes excel columns and plots graphs.
The problem is that when i create the png of the graph it additionaly appears the poit (0;0) witch should be on graph.
In the preview i can't see this point. I attached an example.
Attachments:
Daimler Star22_unknown_unknown_unknown_ACCX_Offset vs temp.png ‏13 KB

Have you tried putting a probe onto the data going into the graph to check there aren't any extra data points (i.e. at 0,0)?
Certified LabVIEW Architect, Certified TestStand Developer
NI Days (and A&DF): 2010, 2011, 2013, 2014
NI Week: 2012, 2014
Knowledgeable in all things Giant Tetris and WebSockets

LabVIEW example problem

Similar Messages

Maybe you are looking for